Rigging Applications Training ITI has specialized in rigging training for 25 years and does it better than anyone in the industry. Riggers from all industries have appreciated ITI s interactive, problem-solving workshops and hands-on training approach to enhance their skill set and knowledge base. Master Rigger Rigging Gear Inspector 2 Day Course Load Weight Estimation Center of Gravity Rigging Removal Criteria Load Control Rigging Capacities Sling Angles & Tensions Horizontal Rigging Rigging Selection Rigging Procedures Accident Case Studies OSHA/ASME Standards Master Rigger 3-5 Day Course Review Load Turning Jacking & Rolling Incline Plane Chain Fall Load Drifting Off-Level Pick Points Spreader Bar s Rigging Blocks & Winching Multiple Crane Communications As the media reminds us of the high rates of accidents occurring to operators and riggers, we at Cianbro Companies strive to provide our employees with the skills and knowledge of how to prevent an accident. In the past our company has received Master Rigging Training from Industrial Training International. They offer a hands-on approach by providing rigging gear inspection, proper rigging procedures and load control using almost any vertical or horizontal rigging system. The classroom teaching techniques and hands-on learning exercises that we have received from the Industrial Training International group has guided our company in creating our own successful in house rigging training program. The Industrial Training International crew and facilities are truly a world class group, solely dedicated to educating and improving the crane and rigging world. George Arsenault, Rigging Training Coordinator, Cianbro Companies 800.727.6355 iti.com
The Program is a test preparation course that prepares participants to take the CIC Nationally Accredited Written and Practical Exams for Certification. It is an excellent program for all who rig under the direct oversight of seasoned rigging personnel. Master Rigger Rigging Gear Inspector CIC Certification Test Preparation Program Sessions Day 1 Slings and Rigging Hardware Identification and Inspection Use of Rigging Equipment Basic Hitch Configurations Knots and Tagline Use Sling Protection Basic Understanding of Crane Operations, Limitations and Capacities Site Considerations / Safety Issues / Hazards Standards / Regulations Standard Voice Communications Signaling Certification Exams Day 2 Nationally accredited certification The written and practical exams will be administered on the second day, following the test-prep program Participants who pass both the written and practical exams will receive CIC Certification, valid for five years All participants completing the test preparation program will receive Certificates of Attendance and Continuing Education Units (CEU s). 800.727.6355 iti.com
Rigging Gear Inspection Rigging Gear Inspector Level I/II 3 Day Course Master Rigger Rigging Gear Inspector The Certified Rigging Gear Inspector Program is designed to build and enhance the skills of students to become qualified, in-house rigging gear inspectors. The program is based on the applicable OSHA and ASME removal criteria and includes classroom workshops and multiple hands-on inspection sessions. Participants who pass the written and hands-on inspections will receive a three year certification. Level I Level II Wire Rope and Wire Rope Slings On-the-job field inspections Synthetic Sling Products Certification achieved after completion of 10 hours of Chain Slings hands-on field inspections Rigging Hardware in each subject area. Below-the-Hook ing Devices Rigging Gear Inspector Level III 3 Day Course The participant must be a Level II certified inspector. The Level III program is designed for the person who considers themselves ready to prove capability and knowledge as an advanced inspector or instructor. The written exam will determine the participant s knowledge of manufacturing and fabrication techniques, ability to troubleshoot problems related to wire rope and rigging systems, and a comprehensive understanding of how the regulations and standards are practically applied to daily crane and rigging activities. A five year certification is issued upon successfully passing the program. Removal criteria Product type and application Field analysis Field inspection processes Fabrication and quality control Wear and abuse prevention Problem-solving techniques Completion of Written Exam I have been to a huge amount of technical training over my 35+ year career and I must enthusiastically say that this course is one of the very best I have ever attended. Superlative organization and instructor/student interchange. Thanks ITI!! Dean Faina, SSA International 800.727.6355 iti.com
Planning Training Master Rigger These courses are designed to provide students with working knowledge of the five primary personnel assignments related to successful crane operations, as outlined in ASME B30.5, and prepares them to plan, design, and implement critical lifts. Rigging Gear Inspector /Site Supervisor 1 Day Course The /Site Supervisor course provides participants with the knowledge and skill to conduct crane and rigging operations following ASME B30.5. The program includes classroom workshops followed by hands-on activities. Site Preparation ASME B30.5 Responsibilities Traffic Control Hazard Recognition Load Chart Confirmation Multiple Crane s Responsibilities of Operator, ing Personnel Rigger, Signaler Critical Planning 2 Day Course Critical Planning is a very intense course that provides participants with the knowledge and skills necessary to properly develop and execute critical lift plans. Load Affirmation Crane Verification Rigging Confirmation Work Site Approval Pre- Checklist Load Schematic Rigging Method Load Travel Path Personnel Placement Load Handling Sequences and Procedures The /Site Supervisor and Critical Planning Courses complement each other and are typically scheduled consecutively over three days. Recently we were required to make a 3-crane pick on an ice breaker barge being built at our facility. This was a specialty lift that required several months of pre-planning including developing a critical lift plan and organizing pre-lift meetings with everyone involved. The lift was a great success! Our experienced crew has gained tremendous knowledge and skill by attending advanced training and hands-on activities provided by Industrial Training International. Challenging workshops, handson instruction and superior instructors prepared us to accomplish projects like this! Troy Higdon, Crane & Rigging Instructor, Jeffboat a division of ACL 800.727.6355 iti.com
Mobile Crane Operator Training Mobile Crane Operator Mobile Crane Initial Mobile Crane Inspector With over 25 years of industry experience, ITI s Mobile Crane Operator Programs are designed to increase the operator s knowledge, skill, and proficiency level through classroom workshops and hands-on training. Mobile Crane Operator Initial 10 Day Course This program is designed for the person who has little or no experience with mobile crane operation. It builds participants knowledge, skill and proficiency through classroom workshops and hands-on operating sessions. The program covers: Crane terminology Basic functions Hand signals Pre-shift inspections Outrigger set up Erect extension Practical exercises Controls Proper leveling Basic crane principles Load charts Mobile Crane Operator ITI Qualified 5 Day Course This program is designed for the incidental or experienced operator and provides participants with the knowledge and skills necessary to properly and proficiently operate mobile cranes and move loads. Classroom workshops are followed by handson operating sessions. Operators who successfully pass the written exams and handson evaluation will receive qualification valid for three years. The program covers: Daily inspection Hand signals Load control Operating practices Load weight estimation Load charts Crane set-up Rigging gear selection Mobile Crane Operator CIC Nationally Accredited Certification 5 Days ITI offers Mobile Crane Operator Certification which is nationally accredited by the National Commission for Certifying Agencies (NCCA) through Crane Institute Certification (CIC). 3-day Test Preparation Course Day four: Written exams administered by a Chief Examiner Day five: Practical exams administered by a Practical Examiner Candidates must pass the written and practical exams to become a certified operator. Certification is valid for five years. 800.727.6355 iti.com
Mobile Crane Inspector Training Mobile Crane Operator Mobile Crane Initial Mobile Crane Inspector ITI s Mobile Crane Inspector Program is designed to increase the participants knowledge of inspection requirements for mobile cranes, and is based on the OSHA and ASME standards. Classroom workshops are followed by hands-on inspections. Mobile Crane Inspector 4 Day Course OSHA / ASME Standards Daily, Monthly & Annual Checklists Inspection Requirements Upper Revolving Structure Electrical, Hydraulic & Air Systems Safety Devices Lower Structure Testing Wire Rope Outriggers Boom Certification is available* *Students can achieve Certified Inspector status by successfully passing the written and hands-on exams. All participants completing the program will receive Excellent class. Thank you. The subject matter covered will be extremely useful and the subject content was just right. Elmer Woods, Energy Northwest 800.727.6355 iti.com
Heavy Equipment Operator Training ITI has specialized in heavy equipment training for 25 years. With an emphasis on operating practices, safety and pre-use inspections, ITI provides training on a variety of equipment. Classroom workshops are followed by hands-on operating activities. Forklift Aerial Work Platforms Inspector training is also available. Inspector training is also available. Telescopic Handler Bucket Truck Inspector training is also available. Inspector training is also available. Skid Steer Construction Equipment Operator qualifications and responsibilities Pre-use inspection OSHA requirements Proper operating practices Certification is available (Vertical and boom-supported) Load ratings Machine stability Pre-operational inspection Proper operating practices Certification is available Operator qualifications and responsibilities Pre-use inspection OSHA requirements Proper operating practices Certification is available Pre-operational inspection Proper operating techniques Certification is available Control Functions Inspections: Daily, Weekly, Monthly, Annual Proper Operating Practices Certification is available (Dozer, backhoe, front-end loader, and grader) Pre-operational inspection Proper operating techniques Thanks, ITI for putting together a specialized course to fit our needs in such short notice. You folks are awesome! Scott P. Kelly, BPA 800.727.6355 iti.com
Overhead Crane Operator Training Overhead Crane Operator Overhead Crane Inspector Overhead Crane Operator Training 1 Day Course This program is designed to instruct the operators in the proper operating techniques and pre-operational inspection of overhead lifting devices which include bridge, gantry, monorail, fixed hoists, and jib wall mounts. The purpose of this training is to provide participants with the knowledge and skill necessary to properly operate overhead cranes. Classroom interactive workshops are followed by hands-on operating activities. This course covers: OSHA and ASME Daily pre-operational inspection Operating practices Load weight estimation Rigging gear selection Load control Hand signals Certification is available This course is often partnered with a rigging applications program. All participants completing the program will receive Instructor was very professional and accommodated our specific needs. Charles Bennett, PacifiCorp 800.727.6355 iti.com
Overhead Crane Inspector Training Overhead Crane Operator Overhead Crane Inspector ITI s Overhead Crane Inspector Program is designed to increase the participants knowledge of inspection requirements for overhead lifting devices which include bridge, gantry, monorail, fixed hoists, and jib wall mounts. The program is based on the OSHA and ASME standards. Classroom workshops are followed by handson inspections. Overhead Crane Inspector Training 4 Day Course OSHA/ASME Standards Hoist Chain Inspection Wire Rope Inspection Wire Rope Installation Daily, Monthly and Annual Checklists Limit Switches Brakes Hooks Structural Drive Trains Runway Electrical Testing Certification is available* *Written exams and hands-on evaluations will be administered. Those inspectors who successfully pass will receive certification that is valid for 3 years. All participants completing the program will receive The program was presented by an instructor who was very knowledgeable and has years of experience in the industry. The information and experience that I received was invaluable. Chris Smith, Technical Trainer, Morrow Equipment Company 800.727.6355 iti.com