PRODUCER STATEMENT PS1 TUBULAR SWIMMING POOL FENCING (NZ MADE)
600mm min between hinges Pool Fence & Gate Design Specifications 2 FUTURA - CLASSIC II End View Self-Closing Spring Hinges. Height of Magnetic Pool Gate Latch 1500mm minimum from ground Panel Width Post with plug or cap W Legal minimum 1200mm Base Post with 4 fixing holes Concrete or timber surface Pool Fences & Gates GALV Butt Welded ALUMINIUM Horizontal top and bottom rail punched to provide strength and drainage ALUMINIUM HORIZONTAL PROFILE 25mm x 25mm 32mm x 32mm 38mm x 25mm 40mm x 40mm 50mm x 50mm VERTICAL PROFILE 16mm diameter 16mm diameter or 16mm square 16mm diameter 19mm diameter 25mm square VERTICAL GAP 99mm or 75mm 99mm 99mm or 59mm 96mm or 56mm 90mm GATE SIDE FRAME 25mm x 25mm 38mm x 25mm 38mm x 25mm 40mm x 40mm 50mm x 50mm OPTIMUM PANEL WIDTH 2150mm 1940mm 1940mm 2060mm 2060mm ABILITY TO RAKE Up to 10 16mm diameter = Up to 5 Up to 30-99mm gap only Up to 10 Up to 2 CONNECTIONS (See Page 20 for details) POSTS (See Pages 17-19 for details) HARDWARE Typical post size: 50sq Aluminium or Galv Refer to Pages 13-16 for options Friars stone Titania Denim Blue Page 2
600mm min between hinges Pool Fence & Gate Design Specifications 2 FUTURA - EDINBURGH III End View Self-Closing Spring Hinges Height of Magnetic Pool Gate Latch 1500mm minimum from ground Panel Width Post with plug or cap W Legal minimum 1200mm Base Post with 4 fixing holes Concrete or timber surface Pool Fences & Gates GALV Butt Welded ALUMINIUM Horizontal top and bottom rail punched to provide strength and drainage ALUMINIUM HORIZONTAL PROFILE 25mm x 25mm 32mm x 32mm 38mm x 25mm 40mm x 40mm 50mm x 50mm VERTICAL PROFILE 16mm diameter 16mm diameter or 16mm square 16mm diameter 19mm diameter 25mm square VERTICAL GAP 99mm or 75mm 99mm 99mm or 59mm 96mm or 56mm 90mm GATE SIDE FRAME 25mm x 25mm 38mm x 25mm 38mm x 25mm 40mm x 40mm 50mm x 50mm OPTIMUM PANEL WIDTH 2150mm 1940mm 1940mm 2060mm 2060mm ABILITY TO RAKE Up to 10 16mm diameter = Up to 5 Up to 30-99mm gap only Up to 10 Up to 2 CONNECTIONS (See Page 20 for details) POSTS (See Pages 17-19 for details) HARDWARE Typical post size: 50sq Aluminium or Galv Refer to Pages 13-16 for options Friars stone Titania Denim Blue Page 4
600mm min between hinges Pool Fence & Gate Design Specifications 2 FUTURA - BALMAIN II End View Self-Closing Spring Hinges Height of Magnetic Pool Gate Latch 1500mm minimum from ground Panel Width Plastic plugs inserted in tops of verticals Post with plug or cap W Legal minimum 1200mm Base Post with 4 fixing holes Concrete or timber surface Pool Fences & Gates Face Welded ALUMINIUM ALUMINIUM Horizontal top and bottom rail punched to provide strength and drainage HORIZONTAL PROFILE 25mm x 25mm 32mm x 32mm 38mm x 25mm 40mm x 40mm 50mm x 50mm VERTICAL PROFILE 16mm diameter 16mm diameter 16mm diameter 19mm diameter 25mm square VERTICAL GAP 99mm 99mm or 59mm 96mm or 56mm 90mm GATE SIDE FRAME 38mm x 25mm 38mm x 25mm 40mm x 40mm 50mm x 50mm OPTIMUM PANEL WIDTH 1940mm 1940mm 2060mm 2060mm See page 8 for specifications Up to 30-99mm gap ABILITY TO RAKE Nil Rake Nil Rake Nil Rake only CONNECTIONS (See Page 20 for details) POSTS (See Pages 17-19 for details) HARDWARE Typical post size: 50sq Aluminium or Galv Refer to Pages 13-16 for options Friars stone Titania Denim Blue Page 6
600mm min between hinges Pool Fence & Gate Design Specifications 2 FACE WELDED - BALMAIN II End View Self-Closing Spring Hinges Height of Magnetic Pool Gate Latch 1500mm minimum from ground Panel Width Plastic plugs inserted in tops of verticals Post with plug or cap W Legal minimum 1200mm Base Post with 4 fixing holes Concrete or timber surface Pool Fences & Gates HORIZONTAL PROFILE VERTICAL PROFILE VERTICAL GAP GATE SIDE FRAME OPTIMUM PANEL WIDTH 25mm x 25mm 16mm diameter 99mm or 75mm 25mm x 25mm 2150mm Face Welded ABILITY TO RAKE Up to 10 CONNECTIONS (See Page 20 for details) POSTS (See Pages 17-19 for details) HARDWARE Typical post size: 50sq Aluminium or Galv Refer to Pages 13-16 for options Friars stone Titania Denim Blue Page 8
600mm min between hinges Pool Fence & Gate Design Specifications 2 FUTURA - SHERWOOD II End View Self-Closing Spring Hinges Height of Magnetic Pool Gate Latch 1500mm minimum from ground Panel Width Post with plug or cap W Legal minimum 1200mm Base Post with 4 fixing holes Concrete or timber surface Pool Fences & Gates Face Welded ALUMINIUM Horizontal top and bottom rail punched to provide strength and drainage HORIZONTAL PROFILE 25mm x 25mm 32mm x 32mm 38mm x 25mm 40mm x 40mm VERTICAL PROFILE 16mm diameter 16mm diameter 16mm diameter 19mm diameter VERTICAL GAP 99mm 99mm 96mm GATE SIDE FRAME 38mm x 25mm 38mm x 25mm 40mm x 40mm OPTIMUM PANEL WIDTH ABILITY TO RAKE See following page for specifications 1940mm Nil Rake 1940mm Up to 5 2060mm Nil Rake CONNECTIONS (See Page 20 for details) POSTS (See Pages 17-19 for details) HARDWARE Typical post size: 50sq Aluminium or Galv Refer to Pages 13-16 for options Friars stone Titania Denim Blue Page 10
600mm min between hinges Pool Fence & Gate Design Specifications 2 FACE WELDED - SHERWOOD II End View Self-Closing Spring Hinges Height of Magnetic Pool Gate Latch 1500mm minimum from ground Panel Width Post with plug or cap W Legal minimum 1200mm Base Post with 4 fixing holes Concrete or timber surface Pool Fences & Gates HORIZONTAL PROFILE VERTICAL PROFILE VERTICAL GAP GATE SIDE FRAME OPTIMUM PANEL WIDTH 25mm x 25mm 16mm diameter 99mm 25mm x 25mm 2150mm Face Welded ABILITY TO RAKE Up to 10 CONNECTIONS (See Page 20 for details) POSTS (See Pages 17-19 for details) HARDWARE Typical post size: 50sq Aluminium or Galv Refer to Pages 13-16 for options Friars stone Titania Denim Blue Page 12
The Adjustable Self-Closing Spring Hinges are designed to assist in the closing of Swimming Pool and Pathway Gates. This product conforms to Pool Safety Standards provided all other fencing materials, manufacturing and installation methods also conform to the same standards. The Manufacturer cannot accept responsibility for an accident where this device is used. Ultimately, pool safety is the responsibility of the owner. Freephone 0800 353 500 www.warnerfences.co.nz ADJUSTABLE SPRING HINGE NOTE: Swimming Pool Gates must be hinged so they self-close and open outwards from the Pool enclosure. 1. Before fixing the hinges, hold the gate in position and decide which way the gate will swing, then mark the location of where the hinges are ideally fixed on. Fix outside screws of both hinges to gate. 2. Fasten other outer hinge flaps to gate post. This has now automatically aligned gate to gatepost. 3. Open gate to 90deg. and fix all inside screws. 4. Adjust tension of both hinges using nail provided. Turn the adjuster (direction shown) and put fixing pin in hole on both hinges until the gate will close by itself. Designed and Manufactured in Australia FIXING PROCEDURE NOTE: For hinges used on Swimming Pool Gates, the tension must be adjusted so gate will self-close from 25mm of closed position. For Heavy Gates it is recommended to fit 3-4 Hinges Page 13 Pool Fence & Gate Design Specifications
Pool Fence & Gate Design Specifications DOWNEE MAGNETIC GATE LATCH 2 Continued next page... Page 14
Freephone 0800 353 500 www.warnerfences.co.nz DOWNEE MAGNETIC GATE LATCH Page 15 Pool Fence & Gate Design Specifications
Pool Fence & Gate Design Specifications D&D MAGNA LATCH 2 Page 16
TYPICAL BASEPLATE FIXING DETAILS: Freephone 0800 353 500 www.warnerfences.co.nz TOP FIXING BASE POSTS (a) To Timber: (b) To Concrete: (c) To Concrete Block: Post Fasteners x 4 Post Fasteners x 4 Post Fasteners x 4 Edge joist Baseplate Baseplate Baseplate Joist (or dummy joist where joists are parallel to the edge) Nog attached to joists Concrete substrate Concrete block with solid concrete infill Base Posts for Pool Fencing & Gates POST PROFILE 40mm x 40mm 50mm x 50mm POST CAPS Plastic Plug Aluminium Cap or Plastic Plug WELD ON BASEPLATE Aluminium: 120mm x 75mm x 6mm Galv: 120mm x 80mm x 6mm Aluminium: 120mm x 75mm x 6mm Galv: 120mm x 80mm x 6mm SCREW ON BASEPLATE N/A Aluminium: 120mm x 100mm x 10mm (a) BASE POST FIXINGS TO TIMBER (b) BASE POST FIXINGS TO CONCRETE (c) BASE POST FIXINGS TO CONCRETE BLOCK 4 x Galv or Stainless Steel Coach Screws: M6 x 90-130mm 4 x Stainless Steel Dynabolts: M10 x 50-100mm 4 x Stainless Steel Threaded Rod: M8-M10 x 100-140mm Note: Above fixings pertain to boundary and pool fencing only. Please refer to Balustrade section for details on balustrade post fixing specifications. Friars stone Titania Denim Blue Page 17 Pool Fence & Gate Design Specifications
Fasteners Fasteners Fasteners Pool Fence & Gate Design Specifications TYPICAL SIDE FIXING DETAILS: SIDE FIXING POSTS 2 (a) To Timber: (b) To Concrete: (c) To Concrete Block/Brick: Post Joist (or dummy joist where joists are parallel to the edge) Post Post Cap Cap Cap Double edge joist, or a single Concrete Nogs attached edge joist with 90mm min. substrate to joists if thickness. Attach structurally required to the joists. Concrete block with solid concrete infill 250mm min fixing depth for side fixed posts Side Fixed Posts for Pool Fencing & Gates POST PROFILE 40mm x 40mm 50mm x 50mm POST CAPS Plastic Plug Aluminium Cap or Plastic Plug (a) SIDE POST FIXINGS TO TIMBER Galv or Stainless Steel Coach Screws: M6 x 90-150mm (b) SIDE POST FIXINGS TO CONCRETE Stainless Steel Dynabolts: M10 x 100mm or Stainless Steel Threaded Rod: M8-M10 x 100- (c) SIDE POST FIXINGS TO CONCRETE BLOCK/BRICK Stainless Steel Threaded Rod: M8-M10 x 100-140mm SIDE POST FIXINGS TO FULL LENGTH WALL See Page 19 for details Note: Above fixings pertain to boundary and pool fencing only. Please refer to Balustrade section for details on balustrade post fixing specifications. Friars stone Titania Denim Blue Page 18
INGROUND POST: INGROUND / SIDE FIX POSTS TYPICAL SIDE FIXING DETAILS (full length posts): Freephone 0800 353 500 www.warnerfences.co.nz (a) To Timber: (b) To Concrete: (c) To Concrete Block/Brick: 600mm minimum Fasteners for side fixings to be a minimum 100mm and a maximum 250mm from top and bottom of posts. 150mm Inground / Side Fix Fence & Gate Posts POST PROFILE 40mm x 40mm 50mm x 50mm POST CAPS Plastic Plug Aluminium Cap or Plastic Plug INGROUND POST HOLE SIZE 150mm diameter x 600mm deep minimum 150mm diameter x 600mmdeep minimum (a) SIDE POST FIXINGS TO TIMBER (b) SIDE POST FIXINGS TO CONCRETE (c) SIDE POST FIXINGS TO CONCRETE BLOCK / BRICK MALE GUDGEONS Galv or Stainless Steel Coach Screws: M6 x 90-150mm Stainless Steel Dynabolts: M10 x 100mm or Stainless Steel Threaded Rod: M8-M10 x 100-140mm Stainless Steel Threaded Rod: M8-M10 x 100-140mm Refer to Accessory Section for options Friars stone Titania Denim Blue Page 19 Pool Fence & Gate Design Specifications
Pool Fence & Gate Design Specifications RAIL CONNECTIONS TO WALLS/POSTS TYPICAL INTERNAL AND EXTERNAL BRACKET FIXING DETAILS: or Internal Brackets can be used at these points 2 Connecting Brackets Suitable 25x25 horizontal profile Rail Brackets Suitable 25x25 horizontal profile WALL: or Internal Brackets can be used at these points Brick Wood Concrete Masonry Internal Connecting Brackets Suitable 32x32/38x25/40x40 horizontal profile Rail Brackets Suitable 32x32/38x25/40x40/50x50 horizontal profile Rail Connections RAIL PROFILE 25mm x 25mm 32mm x 32mm 38mm x 25mm 40mm x 40mm 50mm x 50mm INTERNAL CONNECTION YES YES YES YES NO EXTERNAL CONNECTION () YES YES YES YES YES a) FIXINGS TO TIMBER Wood Screw: 12 gauge 11 x 50mm b) FIXINGS TO BRICK/CONCRETE/MASONRY Metal Tapit or 8mm Raw Plug and 8 gauge Screws c) FIXINGS TO METAL Tek Screw: 12-14 gauge x 20mm Friars stone Titania Denim Blue Page 20