Blue Point Engineering SV203 Interface Overview Overview Sensors Light Sensor Motion Sensor Joystick Computer USB PORT Technical Pointing the Way to Solutions! T http://www.bpesolutions.com Animatronic Applications Control Software USB PORT Computer SV203 Controller Serial Cable USB to Serial Adapter C A USB Cable B - OR - USB Cable Projects Switch -Push Button - Mat Switch -Toggle Switch 1 Position CCW 2 Rotational CW Speed Control Animatronic Character 1 AC Power Sw1 ON Sw 1 - Sw2 OFF Sw 2 ON AC Devices - Motors - Lights - Strobes - Fog Unit DC Devices -DC Motors - Lights - LED's -Special Effects Devices 3 2 way switch 4 A Pneumatics Position B B A C NO Com NC Pneumatic Valve A C Pneumatic Cylinder Blue Point Engineering 213 Pikes Peak Place Longmont, Colorado 80501-3033 USA Custom Equipment, Unique Electronic Products Phone (303) 651-3794 (MST) http://www.bpesolutions.com
USB Cable to SV203 Interface USB-A (M) VSA Control Software Computer ( PC / Mac ) USB PORT USB-B (M) USB-B (F) SV203 Motor Controller Board USB to Serial Adapter Male Connector Female Connector Female Connector Male Connector Serial Cable
SV203 Control Board - SV203 Motor Controller Board Fuse Female Connector Clip Connector Signal (White) (Red) (Black) RTC1 (7) RTCO (6) CCP2 (8) Port C +5V AD3 (3) AD5 (5) AD2 (2) AD4 (4) Port C +5V (9) (10) Sensor Power 4-Cell AA Battery 5-Cell Battery 6V 300mA Adapter No.8 No.7 No.6 No.5 No.4 No.3 No.2 No.1 Port B Optional Power A (1) B (Rx) (2) Z (Tx) (3) Y (4) Multiple Board Port
(Black) (Red) Signal (White) SERVO SETUP Animatronic Character Signal (White) (Red) (Black) +5V (9) (10) POTENTIOMETER 1 5K to 10 k Ohm
Signal (Green) (Black) Port B LED SETUP Port B Signal (Green) (Black) Port B SWITCH SETUP SW3 Micro Push Buttons (Momentary) Port B SW2 SW1
Signal +5V (9) +V (10) TEMPERATURE SENSOR LM34DZ LM34 DZ LM34DZ C LM34 DZ A B Signal +5V (9) (10) A B C +V LIGHT SENSOR Signal CdS Photo Cell 10k Ohm +5V (9) (10) +V BEND SENSOR Signal 10k Ohm +5V (9) (10) +V Bend Sensor
Signal +5V (9) +V (10) IR Receiver (Detector) 1Meg Ohm Anode Cathode PHOTOGATE IR BEAM OBJECT SENSOR Object Signal 220 Ohm Anode Cathode +5V (9) (10) IR Transmitter (Emitter) +V
Signal +5V (9) +V (10) PHOTO DARLINGTON OBJECT SENSOR 12K Ohm Object IR (Emitter) IR (Detector) Signal (10) OPTEK-Photo Darlington Reflective Object Sensor +V 120 Ohm +5V (9) No Object Detection (Non Reflected Source) Emitter Detector Source Object OPTEK-Photo Darlington Reflective Object Sensor Object Detection (Reflected Source) Emitter Detector Source Reflection Object The intensity of reflected source light into the detector sensor determines the voltage value that the photo Darlington sensor will produce. These voltage variables can be detected by the Interface and through software code converted into an object detection or movement of an object as up - down or left - right in position.
RELAY / SOLENOID SETUP Relay Port B R1 D1 C D E LED OPC B T1 E R1 D1 T1 OPC LED A B C A B C N.O. Com. N.C. 4.7 Ohm IN4003 2N2222 Optocoupler RED LED
Slide Potentiometers Joystick Top Half Commercial Joystick PC Raider Joystick (InterAct Game Products) +5V (9) AD2 (2) (10)
Application Example AC Light Dimmer Pack Control 2X - 4X Channel X2 to Analog Converter Board Output Example Light Dimmer Pack Controller Channel 1 GND Output Channel 2 GND Output to Analog Controller No1 to Analog Controller No.2 MPX ADDRESS Light Dimmer Pack Controller (DDS 5600) ANALOG INPUT PORT Common ( GND) Channel 3 Channel 4 Light Dimmer Pack Analog Input ( 0-10 VDC) - CONTROL STATUS - to Analog Controller No1 Channel 2 Channel 1 CHANNEL FUSES 1 2 3 4 PWR MPX 1 2 3 4 Light Dimmer Pack Controller 1 2 3 4 5 6 7 8 ANALOG DDS 5600 Lighting Dimmer USE ONLY 5A 260V NON TIME DELAY FUSES MPX LOOP THRU
Application Example Air Out Pneumatic Valve Control 150 psi Air IN Optional (M) to (M) Jumper Solid State Relay 10 Amp - Vdc
Application Example Solid State Relay 2-Channel 2 Amp - Vdc Solid State Relay 2 Amp - Vdc Optional (M) to (M) Jumper 4- Ch Video Switch
Application Example 8-Channel LED Light Effects Controller (16 Effects) Optional (M) to (M) Jumper Air Pump Control
Application Example Water Pump Control 4- Channel Recorder and Playback Boards
Channel 1 + - Application Example 1-Channel Solid State AC Dimming Control 110 AC Wall Plug in to Analog Controller No1 GND Output + - Caution 110 AC V Light Effects Unit (Plug In) Dimming 0-100% Max - 15 Amp AC V Caution 1 + + 2 +3 Solid State Dimmer Module Crydom (10PCV2415) + + 4 DC + - - DC DC Caution: AC Voltage Use caution when working with AC Voltage. Touching or incorrectly wiring these circuit could cause serious personal injury or damage to equipment.
Application Example Red Wire Red Wire Solid State Relay 10 Amp LED Control Wall Power Supply (12 Vdc @ 1 Amp) Red Wire A Black Wire (-) B LED-Bar 1 + - LED-Light Bars + - (-) (+) B A LED's LED Resistor - OR - LED Resistor
Air Supply Air Hose 5/2 Switching Solenoid Air Valve Exhaust Pneumatic Valve Control - 12 Vdc + 12 Vdc Wire Application Example 12 Vdc Power Supply Air Hose Wire Air Hose Wire Pneumatic Cylinder (Double Acting) Solid State Relay 10 Amp
Application Example Water Valve Effects Wizard - II Controller Board Water Valve Overview Water Valve Channel 2 Fountain Heads Fountain Heads Lawn Water Valve (12 Volts dc) Water Source IN Water Valve Channel 1 Black Wire Red Wire Power Supply (12 Vdc @ 10 Amp ) Channel 2 Channel 1