PanelConnect Module for Sensor Connection To Programmable Controller Technical Data Table of Contents Description Page Description Page System View.................................................... 2 Description..................................................... 3 Benefits........................................................ 3 Minimal Repair and Replacement Time (Plug and Play).................. 4 PanelConnect Cables........................................... 9 Catalog Number Explanation PanelConnect Modules.......................................... 10 PanelConnect Cables........................................... 11 Ordering PanelConnect Modules................................... 12 Selection Tables................................................ 12 PanelConnect Specifications....................................... 30 Digital Cable Specifications....................................... 30 Cable Pinouts................................................... 31 Dimensions.................................................... 34 Marking Systems................................................ 35 Accessories.................................................... 38 Web Site Information............................................. 39 AB Spares
2 PanelConnect Module for Sensor Connection PanelConnect for Sensors Connectivity System View PLC PanelConnect module compatible with many sensor connection systems Pre-wired cable Sensor Patch Cord Power Supply for Sensors Sensor distribution box
PanelConnect Module for Sensor Connection 3 Digital/Analog Programmable Controller Wiring Systems Description Connecting sensors to an Allen-Bradley PLC is very convenient with an Allen- Bradley PanelConnect Module for sensors and cables. Unlike conventional methods of: wiring a number of sensors to a panel connector to maintain the integrity of the enclosure then wiring the connector to a terminal block then wiring to the PLC Input Module or facing the task of providing a seal on a number of cables entering an enclosure Using a PanelConnect Module with associated sensor connection systems, allows connection of up to 16 sensors directly to a 16 point PLC Input module with convenient pre-built cables and connectors. Benefits Simplifies Machine and System Commissioning Often a machine or system is set up at the manufacture and then disassembled for shipping to the job site. Many of the sensor connection need to be initially connected, then disconnected for shipment, and then reconnected for final assembly. When connecting through the enclosure the time and cost providing the reconnection as well as making correct enclosure seals, let alone making the correct connection for final assembly can be greatly simplified and costs reduced using the PanelConnect module and Sensor Connect systems. Commissioning can be done in hours instead of taking weeks and months. Enclosure Integrity The PanelConnect module is a simple system to mount on the enclosure and create the correct seal for the entry of the sensor connections. There is no longer a need to spend the additional time to seal the opening where the sensor cables enter the enclosure or create custom connectors and the associated time and wiring errors to wire to those connectors. AB Spares
4 PanelConnect Module for Sensor Connection Benefits, Continued Reduced Wiring Time and Cost Wiring is completed in a fraction of the time when connecting the "Plug and Play" easy assembly system of PanelConnect modules, Pre-Wired I/O Cables, Sensors Distribution Box and Distribution Box Patch Cords as compared to traditional methods. Both standard and specific build to order length cables are available, providing the correct length for any panel in a neat, space-efficient wiring solution. Lower wiring costs are possible for OEM's and Users as less skilled labor is needed to connect the "Plug and Play" system. Minimal Repair and Replacement Time "Plug and Play" PanelConnect and Sensor system are easily field replaceable using threaded secured connectors and supports the control system requirement for minimal time between diagnoses, repair and up and running. Simplified Design Design engineers can simplify their panel drawings by calling out a PanelConnect Module and pre-wired cable instead of having to detail every single wire and terminal block on their drawings. Simplified panel drawings aid not only the installer but also the end customer who receives the panel. Reduced Wiring Errors Wiring system cables are pre-tested to ensure 100% accurate connections and eliminate the need for point-to-point checking of wiring. No more crossed wires and loose connections between the I/O module and the PanelConnect Module. Even one error in wiring 128 I/O points in a point-to-point system may require a complete check of the wiring. Wiring errors can take several minutes to track down and correct before the panel is ready for startup. When PanelConnect Modules and cables are snapped in place, they fit every time no need to find the wrong or loose connection, resulting in a much higher rate of success at system startup.
PanelConnect Module for Sensor Connection 5 Benefits, Continued Increased Volume and Productivity PanelConnect systems can help OEMs and panel builders produce a higher volume of machines. Inter-connect wiring for a wiring system is 60 times faster to install than traditional point-to-point wiring, enabling OEMs and panel builders using PanelConnect System components to build panels faster and produce more machines. Machine segments also can be outsourced as machine segments can be connected via the "Plug and Play " products. Wiring is completed in a fraction of the time when connecting sensors with the Sensor Connection box and the PanelConnect Module as compared to traditional methods. Design Flexibility To develop a cost-effective system, the hardware components must meet the needs of the design engineer. Allen-Bradley provides the broadest range of PanelConnect, Digital and Analog modules and Cables flexibility with modularity and system expansion capabilities. Allen-Bradley Wiring Systems deliver a lower life-cycle cost. Quality-Looking Panels The pre-wired cables and PanelConnect modules organize the wiring in your panel providing a consistent look. Markers and pre-printed adhesive labels for the terminal wiring neatly identify field-wiring-side connections, which correspond to the I/O module. A large marking area is also available for identifying I/O information on the PanelConnect modules. Reduce DIN Rail Space By mounting the PanelConnect modules on the side of the enclosure terminal block rail space is eliminated in the panel as compared to traditional terminal blocks. AB Spares
6 PanelConnect Module for Sensor Connection Benefits, Continued Reduced Wire Preparation and Routing PanelConnect systems eliminate the time and costs associated with stripping and cutting wires. Pre-wired cables eliminate this step altogether. Routing wires is much easier with wiring systems since engineers only have to worry about routing one pre-wired cable versus 20 wires in the traditional wiring method. Easier Marking and Labeling Three markers on the front of the PanelConnect are provided to mark both I/O module and input points and Sensor Patch Cord cables. Pre-printed, I/O-specific adhesive label strips for quick marking of power supply terminals save labor compared to point-to-point wiring that requires labor-intensive wire markers. No wire labels are required on a pre-wired cable. Fewer Parts, Less Inventory and Lower Carrying Cost A wiring system involves the PanelConnect module and the cable, versus a block, barrier, a jumper, markers, wires, and swing arms with traditional hardwired systems. Therefore, it requires fewer components and, in turn, less inventory and lower carrying costs. Compatibility Works with the other Allen-Bradley 1492 Programmable Controller Wiring Systems, both Digital and Analog Systems. Works with the Allen-Bradley Sensor Connection Systems as well as other leading Connection systems manufactures: Brad Harrison - Daniel Woodhead, Crouse Hinds, Lumberg and Turck. Supports Cables for both Mini Plus and M23 style for Mini and Micro Sensor connectors.
PanelConnect Module for Sensor Connection 7 PanelConnect Features PanelConnect Module with (2) 10-pin Mini-Plus s These modules are used with sensor connection systems without LED s on the sensor connection distribution box. Each 10-pin Mini-Plus connector mates with a 10-conductor patch cord that connects to the distribution box. Additionally on the field connection side, various sensors (including photoelectric sensors and proximity sensors) connect with a variety of connector styles. AC and DC versions of the PanelConnect module are available to meet the sensor voltage requirements. Up to 16 sensors can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-input module. Cables are available to connect to the most popular Allen-Bradley PLC input modules. PanelConnect Module with (2) 12-pin Mini-Plus s These modules are normally used with sensor connection systems with LED s on the sensor connection distribution box. Each 12-pin Mini-Plus connector mates with a 12-conductor patch cord that connects to the distribution box. Additionally on the field connection side, various sensors (including photoelectric sensors and proximity sensors) connect with a variety of connector styles. AC and DC versions of the PanelConnect module are available to meet the sensor voltage requirements. Up to 16 sensors can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-input module. Cables are available to connect to the most popular Allen-Bradley PLC input modules. PanelConnect Module with (2) 12-pin M23 s These modules are used with sensor connection systems with or without LED s on the sensor connection distribution box. Each 12-pin Mini-Plus connector mates with a 10, 11, or 12-conductor patch cord that connects to the distribution box. Additionally on the field connection side, various sensors (including photoelectric sensors and proximity sensors) connect with a variety of connector styles. AC and DC versions of the PanelConnect module are available to meet the sensor voltage requirements. Up to 16 sensors can be connected to each PanelConnect module. Each PanelConnect Module has an LED to indicate when the module is powered. On the internal panel side, the PanelConnect mates with a cable to connect to a PLC-input module. Cables are available to connect to the most popular Allen-Bradley PLC input modules. AB Spares
8 PanelConnect Module for Sensor Connection PanelConnect Features, Continued PanelConnect for Sensors ➊Field side sensor connectors for two keyed 10 pin or two keyed 12 pin main PanelConnect connectors which mate to sensor patchcords. Styles: Mini-plus (10 or 12 pin) M23 (12 pin) ➋PanelConnect input module connector for input module cable. ➌Pre-wired or input ready PanelConnect Module cable. ➍Power supply for Power source input. Note: All of the digitial PanelConnect for sensor products have the following features: Large rectangular write-on area acts as built-in group marking carrier for programmable controller rack, module group, and/or slot information culus Listed and CE Approved Power provides power and ground from Power Source to Sensor and/or I/O ➍ Keyed cable connector (20-pin) with locking tabs for easy installation and secure connection to PanelConnect input module cables ➋ In panel mounting screw LED to indicate when the module is powered Mini-plus or M23 ➊ Pre-wired PanelConnect Input Module Cable ➌ Potted to provide environmental sealing Power Connection 10 or 12-pin Patchcord cable for mating to Main 10 or 12 pin connector Marking area to identify PanelConnect cable connectors and/or customer ID label Gasket eliminates the need to seal the panel Cable clip provided to use as a strain relief for PanelConnect cable PanelConnect cable connector
PanelConnect Module for Sensor Connection 9 PanelConnect Cables Digital Pre-Wired Cables Pre-Wired Cable for PanelConnect Module Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. Pre-wired cables, when used with a PanelConnect Module replaces the point-to-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The pre-wired cables have a removable terminal block or wiring arm at the I/O end of the cable and a cable connector on the other end to connect to the PanelConnect Module. All of the pre-wired cables use #22 AWG wire and are 100% tested for continuity to make a perfect connection every time. The digital pre-wired cables are offered in four standard lengths of 0.5, 1.0, 2.5, and 5.0 m to fit a variety of applications. Other cable lengths are also available as build-to-order products. Pre-wired cables are available for many of the 1746 SLC I/O, 1756 ControlLogix, 1769 Compact for CompactLogix and MicroLogix 1500, and 1771 (PLC-5) Input Modules. Ready-to-Wire Digital Cables PanelConnect Ready Cable for PanelConnect Module PanelConnect-ready cables have a cable connector that attaches to the PanelConnect Module, pre-wired to one end and free connectors ready to wire to other suppliers I/O modules or other components on the other end. PanelConnect ready cables use #22 AWG wire and have individual color-coded conductors for quick wire-to-terminal coordination. The digital PanelConnect-ready cables are offered in standard lengths of 1.0, 2.5, and 5.0 m to fit a variety of applications. Other cable lengths are also available as build-to-order products. AB Spares
10 PanelConnect Module for Sensor Connection Catalog Number Explanation for PanelConnect Modules Important: The following PanelConnect catalog number breakdown is for explanation purposes only. It is not a product configurator. Not all combinations of fields are valid product catalog numbers. First, select the desired PanelConnect module using the steps in Ordering PanelConnect Wiring Systems on page 12. Then, use this breakdown for verification and explanation only. 1492 TPM A 1 2 07 Bulletin No. Through Panel Modules Sensor and Input Module Voltage A 20 pins AC D 20 pins DC PanelConnect Type 1 Mini Plus 2 M23 Sequence number describing internal connection from Patchcord connector to cable connector 01 See Selection Table for 02 03 04 05 06 07 08 09 specific PanelConnect Module and a specific PLC Module. Number of Pins in each Panel and Distribution Box 0 10 Pin 2 12 Pin
PanelConnect Module for Sensor Connection 11 Catalog Number Explanation for PanelConnect Cables Important: Use the following tables as a product configurator for pre-wired, PanelConnect Module -ready, and I/O module-ready cables for Bulletins 1746, 1756, and 1771 digital I/O module cables. Other combinations of these fields make valid product cat. nos for other wiring systems use. 1492 CABLE 010 A Bulletin No. Digital Interface Cable CAB 1769 modules CABLE All other modules Standard or Build-to-Order Length Cable 005 0.5 m (1.64 ft) Standard 010 1.0 m (3.28 ft) 025 2.5 m (8.20 ft) 050 5.0 m (16.40 ft) 001 0.1 2.0 m (0.328 6.56 ft) Build-to-Order 020 0.1 m (0.328 ft) increments 020 100 2.0 10.0 m (6.56 32.8 ft) 0.5 m (1.64 ft) increments 100 990 10.0 99.0 m (32.8 374.72 ft) 1.0 m (3.28 ft) increments Cable Type A AC 1746-IA16 B DC 1746-IB16 1746-IC16 1746-IH16 1746-IN16 1746-ITB16 1746-ITV16 1746-IV16 X AC 1756-IA16 DC 1756-IB16 1756-IB16 1756-IB16 A69 AC 1769-IA16 B69 DC 1769-IQ16 F AC 1771-IAD DC 1771-IBD 1771-ICD 1771-IND P PanelConnect Ready AB Spares
12 PanelConnect Module for Sensor Connection Ordering PanelConnect Module and Sensor Connection Using Selection Tables to determine appropriate product Follow these steps when starting selection from the I/O Module and PanelConnect: 1. Determine the Input voltage type, AC or DC (Use Table A for AC system. Use Table B for DC system.) 2. Determine PLC I/O system that your are using, 1746, 1756, 1769, 1771 3. Determine the Sensor Connection main connector style, Mini-Plus (1 1/8 in.) or Metric (M23) 4. Determine if Sensor Distribution Box uses LED indicators 5. Select the appropriate PanelConnect module and a cable Note: Note appropriate Connection System suppliers are noted in Tables A and B. Refer to Table C for each supplier for Sensor Distribution Box details. Follow these steps when starting selection from Sensor Distribution Box and sensor connect type: From Table C (Determine Sensor Distribution Box details, first) 1. Determine manufacture of sensor distribution box 2. Determine sensor voltage type AC or DC, and nominal voltage 3. Determine LED or not LED on Distribution Box 4. Determine sensor connection type 5. Select PanelConnect Module for Sensors and a cable Refer to table "A" to determine appropriate I/O system and PanelConnect Cable. From Table D, determine Patch Cord details for Allen-Bradley Distribution Boxes and PanelConnect Modules. Ordering Digital PanelConnect-Ready Cables For pinout and wiring information, refer to PanelConnect Ready Cable Specifications on page 30 and the selection table on page 19.
PanelConnect Module for Sensor Connection 13 Selection Tables Using Selection Tables to Make Valid Catalog Numbers Configure the cable catalog number using 1492-CABLE➊ (for digital cables). See footnote ➊ on pages 13 and 14. Table A (For AC systems) AC Main Style Mini-plus (1 1/8 in.) Metric M23 s (2) 10 Pin 12 Pin 12 Pin Box LED's without LED with LED Either with or without LED ➊ Cat. No. Cat. No. Cat. No. Allen-Bradley 1492-TPMA1008 1492-TPMA1207 Brad Harrison (Daniel 1492-TPMA1008 1492-TPMA1207 Woodhead) Crouse-Hinds 1492-TPMA1008 1492-TPMA1207 Lumberg 1492-TPMA1008 1492-TPMA1207 Turck 1492-TPMA2209 Cat. No. Cat. No. Cat. No. I/O Nominal Range Frequency @ I/O Module 1492-TPMA1008 1492-TPMA1207 1492-TPMA2209 System System System Module 1746 100/120 V 85 132V AC 47 63 Hz 1746-IA16 1492-CABLE➊A 1492-CABLE➊A 1492-CABLE➊A AC 24 V AC 10 30V AC 47 63 Hz 1746-IN16 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1756 120V AC 74 132V AC 47 63 Hz 1756-IA16 1492-CABLE➊X 1492-CABLE➊X 1492-CABLE➊X 24V AC 10 30 V AC 47 63 Hz 1756-IN16 1492-CABLE➊X 1769 100/120V 79 132V AC 47 63 Hz 1769-IA16 1492-CAB➊A69 1492-CAB➊A69 1492-CAB➊A69 AC 1771 120V AC 70 138V AC 50/60 Hz 1771-IAD 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 24V AC 16 30V AC 50/60 Hz 1771-IND 1492-CABLE➊F 1492-CABLE➊F Other AC PLC Input Modules 1492-CABLE➊P 1492-CABLE➊P 1492-CABLE➊P Cables are available in standard lenghts of 0.5 m, 1.0 m, and 5.0 m. To order, insert the desired length code in the catalog number ( 005 = 0.5 m, 010 = 1.0 m, 0.25 = 2.5 m, and 050 = 5 m). Example: 1492-CABLE005B is for a 0.5 m cable for the 1746-IB16 I/O module. 1492-CABLE➊P has minimum length of 1.0 m. AB Spares
14 PanelConnect Module for Sensor Connection Selection Tables, Continued Table B (For DC systems) DC Main Mini-plus (1 1/8in.) Metric M23 s (2) 10 Pin 12 Pin 12 Pin 12 Pin 12 Pin 12 Pin Box Without LED With LED Either with or without LED Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Allen-Bradley 1492- TPMD1004 Brad Harrison (Daniel 1492- Woodhead) TPMD1004 1492- TPMD1201 1492-1492- TPMD1202 TPMD2006 Crouse-Hinds 1492- TPMD1004 Lumberg 1492-1492- TPMD1203 TPMD2206 System Turck 1492-1492- TPMD2205 TPMD2206 I/O Nominal Range @ Module I/O 1492-1492- 1492-1492- 1492-1492- System Module TPMD1004 TPMD1201 TPMD1202 TPMD1203 TPMD2205 TPMD2206 1746 24V DC 10 30V Sink 1746-IB16 1492-1492- 1492-1492- 1492-1492- DC CABLE➊B CABLE➊B CABLE➊B CABLE➊B CABLE➊B CABLE➊B 48V DC 30 60V Sink 1746-IC16 1492-1492- 1492- DC CABLE➊B CABLE➊B CABLE➊B 120V DC 90 146V Sink 1746-IH16 1492- DC CABLE➊B 24V DC 10 30V Sink 1746-IN16 1492-1492- 1492-1492- 1492-1492- DC CABLE➊B CABLE➊B CABLE➊B CABLE➊B CABLE➊B CABLE➊B 24V DC 10 30V Sink 1746-1492- 1492-1492- 1492-1492- 1492- DC ITB16 CABLE➊B CABLE➊B CABLE➊B CABLE➊B CABLE➊B CABLE➊B 24V DC 10 30V Source 1746-1492- 1492-1492- 1492-1492- DC ITV16 CABLE➊B CABLE➊B CABLE➊B CABLE➊B CABLE➊B 24V DC 10 30V Source 1746-IV16 1492-1492- 1492-1492- 1492- DC CABLE➊B CABLE➊B CABLE➊B CABLE➊B CABLE➊B 1756 12/24V 10 30V sink 1756-IB16 1492-1492- 1492-1492- 1492-1492- DC DC CABLE➊X CABLE➊X CABLE➊X CABLE➊X CABLE➊X CABLE➊X 48V DC 30 60V sink 1756-IC16 1492-1492- 1492- DC CABLE➊X CABLE➊X CABLE➊X 1769 24V DC 10 30V Sink or Source 1769-IQ16 1492-1492- 1492-1492- 1492-1492- DC CAB➊B69 CAB➊B69 CAB➊B69 CAB➊B69 CAB➊B69 CAB➊B69 1771 125V DC 70 138V Sink 1771-IAD 1492- DC CABLE➊F ➋ 24V DC 10 30V Sink 1771-IBD 1492-1492- 1492-1492- 1492-1492- DC CABLE➊F CABLE➊F CABLE➊F CABLE➊F CABLE➊F CABLE➊F 48V DC 20 60V Sink 1771-ICD 1492-1492- 1492- DC CABLE➊F CABLE➊F CABLE➊F 24V DC 9 30V DC Sink 1771-IND 1492-1492- 1492-1492- 1492-1492- CABLE➊F ➌ CABLE➊F CABLE➊F CABLE➊F CABLE➊F CABLE➊F Other DC PLC Input Modules 1492-1492- 1492-1492- 1492-1492- CABLE➊P CABLE➊P CABLE➊P CABLE➊P CABLE➊P CABLE➊P ➊ Cables are available in standard lenghts of 0.5 m, 1.0 m, and 5.0 m. To order, insert the desired length code in the catalog number ( 005 = 0.5 m, 010 = 1.0 m, 0.25 = 2.5 m, and 050 = 5 m). Example: 1492-CABLE005B is for a 0.5 m cable for the 1746-IB16 I/O module. 1492-CABLE➊P has minimum length of 1.0 m. ➋ Excluding Brad Harrison. ➌ Excluding Crouse Hinds.
PanelConnect Module for Sensor Connection 15 Selection Tables, Continued Table C Sensor Distribution Boxes Allen-Bradley Distribution Boxes PanelConnect Sensor Connection System 8 sensor connections Module for Sensors Cat. No. Cat. No. Voltage Type Voltage Range System LED on Connection Box Main Type Sensor Type 1492-TPMA1008 898N-38PS-N10 AC 85-132V AC No 10 pin Mini-Plus (1 1/8") 3-pin Mini 1492-TPMA1207 898N-L38PS-N12 AC 85-132V AC Yes 12 pin Mini-Plus (1 1/8") 3-pin Mini 1492-TPMD1004 898N-48PS-N10 DC 10-30V DC No 10 pin Mini-Plus (1 1/8") 4-pin Mini 1492-TPMD1201 898D-58PT-N12 ➊ DC 10-30V DC No 12 pin Mini-Plus (1 1/8") 4-pin Micro 898D-N58PT-N12 ➋ DC 10-30V DC Yes 12 pin Mini-Plus (1 1/8") 4-pin Micro NPN 898D-P58PT-N12 ➌ DC 10-30V DC Yes PNP 12 pin Mini-Plus (1 1/8") 4-pin Micro Brad-Harrison (Daniel Woodhead) Distribution Boxes PanelConnect Module for Sensors Sensor Connection System 8 sensor connections Cat. No. Cat. No. Voltage Type Voltage Range LED on Connection Box Main Type Sensor Type 1492-TPMA1008 409P801 AC 85-132 V AC No 10 pin Mini-Plus (1 1/8") 3-pin Mini 702P801 AC 85-132 V AC No 10 pin Mini-Plus (1 1/8") 3-pin Micro 1492-TPMA1207 410P801 AC 85-265 V AC Yes 12 pin Mini-Plus (1 1/8") 3-pin Mini 712P801 AC 85-265 V AC Yes 12 pin Mini-Plus (1 1/8") 3-pin Micro 1492-TPMD1004 411P801 DC 10-30V DC No 10 pin Mini-Plus (1 1/8") 4-pin Mini 1492-TPMD1202 BTY801P-FBB ➌ DC 10-30 V DC Yes 12 pin Mini-Plus (1 1/8") 5-pin Micro PNP BTY801N-FBB ➋ DC 10-30 V DC Yes 12 pin Mini-Plus (1 1/8") 5-pin Micro NPN 1492-TPMD2206 BTY801P-FBC ➌ DC 10-30 V DC Yes 12 pin M23 5-pin Micro PNP BTY801N-FBC ➋ DC 10-30 V DC Yes 12 pin M23 5-pin Micro NPN Note: All References to Crouse Hinds, Daniel Woodhead, Lumberg and Turck were obtained from manufactuers commercial literature. Refer to manufacturer s literature for specific information. ➊ Compatible with all DC input modules listed on page 14 for 1492-TPMD1201. ➋ Compatible with ONLY source (or Sink/Source) type Input Modules: 1746-ITV16, 1746-IV16, 1769-IQ16. ➌ Compatible with ONLY source (or Sink/Source) type Input Modules: 1746-IB16, 1746-IN16, 1746-ITB16, 1746-ITB16, 1756-IB16, 1769-IQ16, 1771-IBD, 1771-IND. AB Spares
16 PanelConnect Module for Sensor Connection Selection Tables, Continued Table C Sensor Distribution Boxes, Continued Crouse-Hinds Distribution Boxes PanelConnect Sensor Connection System-8 sensor connection Module for Sensors Cat. No. Cat. No. Voltage Type Voltage Range LED on Connection Box Main Type Sensor Type 1492-TPMA1008 MP8FA000 AC 85-132 V AC No 10 pin Mini-Plus 3-pin Mini (1 1/8") 1492-TPMA1207 MP8FC000 AC 85-265 V AC Yes 12 pin Mini-Plus 3-pin Mini (1 1/8") 1492-TPMD1004 MP8FD000 DC 10-30 V DC No 10 pin Mini-Plus (1 1/8") 4-pin Mini Lumberg Distribution Boxes PanelConnect Sensor Connection System 8 sensor connection Module for Sensors Cat. No. Cat. No. Voltage Type Voltage Range LED on Connection Box Main Type Sensor Type 1492-TPMA1008 ZVS8-30 AC 85-132 V AC No 10 pin Mini-Plus 3-pin Mini (1 1/8") 1492-TPMA1207 ZVS8/LED-30 AC 85-265 V AC Yes 12 pin Mini-Plus 3-pin Mini (1 1/8") 1492-TPMD1203 ASB8/LED5/4-14- DC 10-30 V DC Yes 12 pin Mini-Plus 5-pin Micro RS120M PNP (1 1/8") 1492-TPMD2206 ASBS85/4 ➊ DC 10-30 V DC No 12 pin M23 5-pin Micro ASBS8/LED5/4 ➋ DC 10-30 V DC Yes 12 pin M23 5-pin Micro Turck Distribution Boxes PanelConnect Sensor Connection System 8 sensor connection Module for Sensors Cat. No. Cat. No. Voltage Type Voltage Range LED on Connection Box Main Type Sensor Type 1492-TPMA2209 8RKF30-X9-CS12 AC 85-132V AC Yes 12 pin M23 3-pin Mini metal VBKB80-X9-CS12 AC 85 132V AC Yes 12 pin M23 3-pin Micro 1492-TPMD2205 VBM80-CS12 DC 10 48V DC Yes 12 pin M23 5-pin Micro metal ➌ NPN VB80-CS12 ➌ DC 10 48V DC Yes 12 pin M23 5-pin Micro NPN VB80N7X9-CS12 ➍ DC 10 48V DC Yes 12 pin M23 5-pin Micro NPN VB80P7X9-CS12 ➎ DC 10 48V DC Yes PNP 12 pin M23 5-pin Micro Note: All References to Crouse Hinds, Daniel Woodhead, Lumberg and Turck were obtained from manufactuers commercial literature. Refer to manufacturer s literature for specific information. ➊ Compatible with all DC input modules listed on page 14 for 1492-TPMD2206. ➋ Compatible with ONLY source (or Sink/Source) type Input Modules: 1746-IB16, 1746-IN16, 1746-ITB16, 1756- IB16, 1769-IQ16, 1771-IBD, 1771-IND. ➌ Compatible with all DC Input Modules listed on page 14 for 1492-TPMD2205. ➍ Compatible with ONLY source (or Sink/Source) type Input Modules: 1746-IB16, 1746-IC16, 1746-IN16, 1756-IC16, 1769-IQ16, 1771-IBD, 1771-IND. ➎ Compatible with ONLY source (or Sink/Source) type Input Modules: 1746-ITV16, 1746-IV16, 1769-IQ16.
PanelConnect Module for Sensor Connection 17 Selection Tables, Continued Table D Allen-Bradley Patchcord for PanelConnect Patch Cord Connects PanelConnect to Sensor Distribution Box Cat No. Diameter Wire Rating Length Type Male Female mm (in) m (ft) 889N-F10AFNU-2 17 (0.67) 16AWG 2 (6.5) 10 pin Mini-Plus (1 1/8") Straight Straight 889N-F10AFNU-3 600V 7A 3 (9.8) 889N-F10AFNU-5 5 (16.4) 889N-F10AFNU-10 10 (32.8) 889N-F12AFNU-2 18 (0.71) 2 (6.5) 12 pin Mini-Plus (1 1/8") 889N-F12AFNU-3 3 (9.8) 889N-F12AFNU-5 5 (16.4) 889N-F12AFNU-10 10 (32.8) 889N-F10AFNV-2 17 (0.67) 2 (6.5) 10 pin Mini-Plus (1 1/8") Right Angle 889N-F10AFNV-3 3 (9.8) 889N-F10AFNV-5 5 (16.4) 889N-F10AFNV-10 10 (32.8) 889N-F12AFNV-2 18 (0.71) 2 (6.5) 12 pin Mini-Plus (1 1/8") 889N-F12AFNV-3 3 (9.8) 889N-F12AFNV-5 5 (16.4) 889N-F12AFNV-10 10 (32.8) 889N-F10ACNU-2 9 (0.36) 18/22AWG 2 (6.5) 10 pin Mini-Plus (1 1/8") Straight 889N-F10ACNU-3 300V 3A 3 (9.8) 889N-F10ACNU-5 5 (16.4) 889N-F10ACNU-10 10 (32.8) 889N-F12ACNU-2 2 (6.5) 12 pin Mini-Plus (1 1/8") 889N-F12ACNU-3 3 (9.8) 889N-F12ACNU-5 5 (16.4) 889N-F12ACNU-10 10 (32.8) 889N-F10ACNV-2 2 (6.5) 10 pin Mini-Plus (1 1/8") Right Angle 889N-F10ACNV-3 3 (9.8) 889N-F10ACNV-5 5 (16.4) 889N-F10ACNV-10 10 (32.8) 889N-F12ACNV-2 2 (6.5) 12 pin Mini-Plus (1 1/8") 889N-F12ACNV-3 3 (9.8) 889N-F12ACNV-5 5 (16.4) 889N-F12ACNV-10 10 (32.8) Note: Custom assembled patchcords or patchcords from other manufacturers are available. AB Spares
18 PanelConnect Module for Sensor Connection Selection Tables, Continued Table E Bulletins 1746, 1756, 1769, 1771 Input Modules with PanelConnect and Cable Solutions These pre-wired cables have a pre-wired removable terminal block (RTB) or wiring arm on one end to connect to the front of a related input module and a connector on the other end to plug into a 20-terminal PanelConnect. You must first select the PanelConnect from one of the preceding selection tables. Panel Connect Module I/O Module PanelConnect Cat. No. 1492-TPMA1008 1492-TPMA-1207 1492-TPMA2209 1492-TPMD1004 1492-TPMD1201 1492-TPMD1202 1492-TPMD1203 1492-TPMD2205 1492-TPMD2206 1746-IA16 1492-CABLE➊A 1492-CABLE➊A 1492-CABLE➊A 1746-IB16 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1746-IC16 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1746-IH16 1492-CABLE➊B 1746-IN16 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1746-ITB16 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1746-ITV16 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1746-IV16 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1492-CABLE➊B 1756-IA16 1492-CABLE➊X 1492-CABLE➊X 1492-CABLE➊X 1756-IB16 1492-CABLE➊X 1492-CABLE➊X 1492-CABLE➊X 1492-CABLE➊X 1492-CABLE➊X 1492-CABLE➊X 1756-IC16 1492-CABLE➊X 1492-CABLE➊X 1492-CABLE➊X 1756-IN16 1492-CABLE➊X 1492-CABLE➊X 1492-CABLE➊X 1769-IA16 1492-CAB➊A69 1492-CAB➊A69 1492-CAB➊A69 1769-IQ16 1492-CAB➊B69 1492-CAB➊B69 1492-CAB➊B69 1492-CAB➊B69 1492-CAB➊B69 1492-CAB➊B69 1771-IAD 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1771-IBD 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1771-ICD 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1771-IND 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F 1492-CABLE➊F ➊ Cables are available in standard lenghts of 0.5 m, 1.0 m, and 5.0 m. To order, insert the desired length code in the catalog number ( 005 = 0.5 m, 010 = 1.0 m, 0.25 = 2.5 m, and 050 = 5 m). Example: 1492-CABLE005B is for a 0.5 m cable for the 1746-IB16 I/O module.
PanelConnect Module for Sensor Connection 19 Selection Tables, Continued Table F PanelConnect-Ready I/O Cables PanelConnect-ready cables have a cable connector on one end to attach to the PanelConnect and 20 individually color-coded conductors on the other end (CABLE➊P). These cables allow the PanelConnect to be used in specialty applications that require a custom connection. PanelConnect-Ready I/O Cable Cable Cat. No. Standard Cable Lengths Insulation Rating No. Conductors Conductor Size Nominal Outer Diameter Current/ Conductor 1492-CABLE➊P 1.0, 2.5, 5.0 m 300V, 80 C 20 22AWG 9mm (0.36in.) 2A ➊ Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the desired cable length into the cat. no. (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE025P is for a 2.5 m, 20 conductor PanelConnect-ready cable. Also refer to 19 on page 19. Build-to-Order Length Cables Build-to-Order Length Cables Cable Lengths Increment Size Cable Length Codes Example Cat. No. 0.1 2.0 m 0.1 m 001 020 1492-CABLE015A (1.5 m cable) 2.0 10.0 m 0.5 m 020 100 1492-CABLE075P (7.5 m cable) 10.0 99.0 m 1.0 m 100 990 1492-CABLE150F (15.0 m cable) All Bulletin 1492 cables are available in build-to-order lengths. Consult your local Allen-Bradley Sales Office or distributor for availability. AB Spares
20 PanelConnect Module for Sensor Connection Digital PanelConnect Specifications Digital/Analog Programmable Controller Wiring Systems For all PanelConnect dimensions, refer to page 34. For general Marker Card information, refer to page 35. For general Adhesive Label Card information, refer to page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web page at http://www.ab.com/catalogs/b113/. Refer to page 39 for specific platform web site information. Refer to the online documentation for new product information. 19 1 20 2
PanelConnect Module for Sensor Connection 21 1492-TPMA1008 Pinout Mini-Plus 10 PIN 1-1/8 In. 8 7 9 1 10 5 3 1492-TPMA1008 Specifications Main PanelConnect ➊ ➋ Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 10 Style Mini-Plus 1 1/8 in. IP65 NEMA 1, 3, 4, 12, 13 10 265V AC 600V p 2A 12 A 2 ma Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand.. Maximum number of the same gauge stranded copper conductors allowed per wire funnel. 2 0 +60 C Non-Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Panel Connections Input Pin Reference Application Notes CHANNEL 0-7 A Field Side CHANNEL 8-15 B Input Pin Reference Field Side 1 15 B3 2 16 B4 3 A7 17 B5 4 A1 18 B6 5 A9 19 6 A2 20 7 A3 Power Pin Reference 8 A4 C A10, B10 9 A5 D 10 A6 E A8, B8 11 B7 12 B1 13 B9 14 B2 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. 3. Dimensions Refer to page 34. AB Spares
22 PanelConnect Module for Sensor Connection 1492-TPMA1207 Pinout Mini-Plus 12 PIN 1-1/8 In. 8 9 1 10 2 12 7 6 3 5 4 11 1492-TPMA1207 Specifications Main PanelConnect ➊ ➋ Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 12 Style Mini-Plus 1 1/8 in. IP65 NEMA 1, 3, 4, 12, 13 10 265V AC 600V p 2A 12 A 2mA Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand. Maximum number of the same gauge stranded copper conductors allowed per wire funnel. 2 0 +60 C Non Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Panel Connections Input Pin Reference Application Notes CHANNEL 0-7 A Field Side CHANNEL 8-15 Input Pin Reference Field Side 1 A7, B7 15 B3 2 16 B4 3 A10 17 B5 4 A1 18 B6 5 A12 19 A7, B7 6 A2 20 7 A3 Power Pin Reference 8 A4 C A11, B11 9 A5 D A7, B7 10 A6 E A9, B9 11 B10 12 B1 13 B12 14 B2 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. 3. Dimensions Refer to page 34. B
PanelConnect Module for Sensor Connection 23 1492-TPMA2209 Pinout M23 12 PIN 23 mm 1 9 8 12 10 3 5 11 7 1492-TPMA2209 Specifications Main PanelConnect Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 12 Style M23 Metric 23 mm. IP65 NEMA 1, 3, 4, 12, 13 10 265V AC 600V p 2A 12 A 2mA 2 0 +60 C Non-Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Panel Connections Input Pin Reference CHANNEL 0-7 A Field Side CHANNEL 8-15 Input Pin Reference Field Side 1 A7, B7 15 B3 2 16 B4 3 A10 17 B5 4 A1 18 B6 5 A12 19 A7, B7 6 A2 20 7 A3 Power Pin Reference 8 A4 C A11, B11 9 A5 D A7, B7 10 A6 E A9, B9 11 B10 12 B1 13 B12 14 B2 B ➊ Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand. Application Notes ➋ Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Maximum number of the same gauge stranded copper conductors allowed per wire funnel. 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. 3. Dimensions Refer to page 34. AB Spares
24 PanelConnect Module for Sensor Connection 1492-TPMD1004 Pinout Mini-Plus 10 PIN 1-1/8 In. 8 7 9 1 10 5 3 1492-TPMD1004 Specifications Main PanelConnect Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 10 Style Mini-Plus 1 1/8 in. IP65 NEMA 1, 3, 4, 12, 13 10 265V DC 600V p 2A 12 A 2 ma 2 0 +60 C Non-Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Panel Connections Input Pin Reference CHANNEL 0-7 A Field Side CHANNEL 8-15 B Input Pin Reference Field Side 1 A8, B8 15 B3 2 16 B4 3 A7 17 B5 4 A1 18 B6 5 A9 19 A8, B8 6 A2 20 7 A3 Power Pin Reference 8 A4 C A10, B10 9 A5 D A8, B8 10 A6 E 11 B7 12 B1 13 B9 14 B2 ➊ Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand. Application Notes ➋ Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Maximum number of the same gauge stranded copper conductors allowed per wire funnel. 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. 3. Dimensions Refer to page 34.
PanelConnect Module for Sensor Connection 25 1492-TPMD1201 Pinout Mini-Plus 12 PIN 1-1/8 In. 8 9 1 10 2 12 7 6 3 5 4 11 1492-TPMD1201 Specifications Main PanelConnect Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 12 Style Mini-Plus 1 1/8 in. IP65 NEMA 1, 3, 4, 12, 13 10 265V DC 600V p 2A 12 A 2mA 2 0 +60 C Non Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Panel Connections Input Pin Reference CHANNEL 0-7 A Field Side CHANNEL 8-15 Input Pin Reference Field Side 1 A11, B11 15 B5 2 16 B6 3 A1 17 B7 4 A2 18 B8 5 A3 19 A11, B11 6 A4 20 7 A5 Power Pin Reference 8 A6 C A12, B12 9 A7 D A11, B11 10 A8 E A9, B9 11 B1 12 B2 13 B3 14 B4 B ➊ Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand. Application Notes ➋ Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Maximum number of the same gauge stranded copper conductors allowed per wire funnel. 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. 3. Dimensions Refer to page 34. AB Spares
26 PanelConnect Module for Sensor Connection 1492-TPMD1202 Pinout Mini-Plus 12 PIN 1-1/8 In. 8 9 1 10 2 12 7 6 3 5 4 11 CHANNEL 0-7 A CHANNEL 8-15 B 1492-TPMD1202 Specifications Main PanelConnect ➊ ➋ Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 12 Style Mini-Plus 1 1/8 in. IP65 NEMA 1, 3, 4, 12, 13 10 265V DC 600V p 2A 12 A 2 ma Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand. Maximum number of the same gauge stranded copper conductors allowed per wire funnel. 2 0 +60 C Non Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Panel Connections Input Pin Reference Application Notes Field Side Input Pin Reference Field Side 1 A11, B11 15 B5 2 16 B6 3 A1 17 B7 4 A2 18 B8 5 A3 19 A11, B11 6 A4 20 7 A5 Power Pin Reference 8 A6 C A10, B10 9 A7 D A11, B11 10 A8 E A9, B9 11 B1 12 B2 13 B3 14 B4 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. 3. Dimensions Refer to page 34.
PanelConnect Module for Sensor Connection 27 1492-TPMD1203 Pinout Mini-Plus 12 PIN 1-1/8 In. 8 9 1 10 2 12 7 6 3 5 4 11 1492-TPMD1203 Specifications Main PanelConnect Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 12 Style Mini-Plus 1 1/8 in. IP65 NEMA 1, 3, 4, 12, 13 10 265V DC 600V p 2A 12 A 2 ma 2 0 +60 C Non Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Panel Connections Input Pin Reference CHANNEL 0-7 A Field Side CHANNEL 8-15 Input Pin Reference Field Side 1 A10, B10 15 B3 2 16 B2 3 A7 17 B1 4 A6 18 B8 5 A5 19 A10, B10 6 A4 20 7 A3 Power Pin Reference 8 A2 C A12, B12 9 A1 D A10, B10 10 A8 E A9, B9 11 B7 12 B6 13 B5 14 B4 B ➊ ➋ Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand. Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Application Notes Maximum number of the same gauge stranded copper conductors allowed per wire funnel. AB Spares 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. 3. Dimensions Refer to page 34.
28 PanelConnect Module for Sensor Connection 1492-TPMD2205 Pinout M23 12 PIN 23 mm 1 9 8 12 10 3 5 11 7 1492-TPMD2205 Specifications Main PanelConnect Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 12 Style M23 Metric 23mm IP65 NEMA 1, 3, 4, 12, 13 10 265V DC 600V p 2A 12 A 2 ma 2 0 +60 C Non-Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Panel Connections Input Pin Reference CHANNEL 0-7 A Field Side CHANNEL 8-15 Input Pin Reference Field Side 1 A3, B3 15 B8 2 16 B9 3 A4 17 B10 4 A5 18 B11 5 A6 19 A3, B3 6 A7 20 7 A8 Power Pin Reference 8 A9 C A1, B1 9 A10 D A3, B3 10 A11 E A12, B12 11 B4 12 B5 13 B6 14 B7 B ➊ Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand. Application Notes ➋ Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Maximum number of the same gauge stranded copper conductors allowed per wire funnel. 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. Dimensions Refer to page 34.
PanelConnect Module for Sensor Connection 29 1492-TPMD2206 Pinout M23 12 PIN 23 mm 1 9 8 12 10 3 5 11 7 1492-TPMD2206 Specifications Main PanelConnect ➊ ➋ Degree of Protection Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common Operating Temperature Range Approvals No. Pins 12 Style M23 Metric 23 mm IP65 NEMA 1, 3, 4, 12, 13 10 265V DC 600V p 2A 12 A 2 ma Transient voltage greater than >600V p use a UL recognized suppression device rated at 2.5 kv withstand. Maximum number of the same gauge stranded copper conductors allowed per wire funnel. 2 0 +60 C Non-Condensing culus-listed (File E113724 Guide NRAQ) CE Approved Power Supply Specification Wire Range (Rated Cross Section) ➋ Wire Strip Length Recommended Tightening Torque #22 #12 AWG (0.2 4 mm 2 ) 0.32 in. (8 mm) 4.5 5.5 lb-in. (0.50 0.60 Nm) Panel Connections Input Pin Reference Application Notes CHANNEL 0-7 A Field Side CHANNEL 8-15 Input Pin Reference Field Side 1 A9, A10, 15 B5 2 B9, B10 16 B6 3 A1 17 B7 4 A2 18 B8 5 A3 19 A9, A10, 6 A4 20 B9, B10 7 A5 Power Pin Reference 8 A6 C A11, B11 9 A7 D A9, A10, B9, B10 10 A8 E A12, B12 11 B1 12 B2 13 B3 14 B4 1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the PanelConnect Module. 2. Wiring Refer to the Label Section on page 37. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 39. 3. Dimensions Refer to page 34. B AB Spares
30 PanelConnect Module for Sensor Connection Digital Cable Specifications Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. Digital pre-wired cables, when used with an PanelConnect Module, replace the point-to-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The digital ready-to-wire cables provide one end of the cable pre-terminated, for the PanelConnect Module. Pre-Wired Cables Specifications The pre-wired cables have a Bulletin 1746 Removable Terminal Block, 1756 Removable Terminal Block, 1769 Removable Terminal Block, or 1771 Wiring Arm on one end and a cable connector on the other to connect to the PanelConnect Module. The broad offering of digital pre-wired cables supports 16--point Bulletin 1746, 1756, 1769, and 1771 digital input modules. Digital Pre-Wired Cable Specifications Cat. No. Standard Cable Lengths Insulation Rating No. of Conductors Conductor Size Nominal Outer Diameter I/O Module Cat. No. 1492-CABLE➊A 0.5, 1.0, 2.5, 5.0 m 300V 80 C 20 #22 AWG 9.0 mm (0.36") 1746-RT25R Red Removable Terminal Block 1492-CABLE➊B 0.5, 1.0, 2.5, 5.0 m 300V 80 C 20 #22 AWG 9.0 mm (0.36") 1746-RT25B Blue Removable Terminal Block 1492-CABLE➊F 0.5, 1.0, 2.5, 5.0 m 300V 80 C 20 #22 AWG 9.0 mm (0.36") 1771-WH (16-Point/21 Terminal) Wiring Arm 1492-CABLE➊X 0.5, 1.0, 2.5, 5.0 m 300V 80 C 20 #22 AWG 9.0 mm (0.36") 1756-TBNH Removable Terminal Block 1492-CAB➊A69 0.5, 1.0, 2.5, 5.0 m 300V 80 C 20 #22 AWG 9.0 mm (0.36") 1769-RTBN18 Removable Terminal Block 1492-CAB➊B69 0.5, 1.0, 2.5, 5.0 m 300V 80 C 20 #22 AWG 9.0 mm (0.36") 1769-RTBN18 Removable Terminal Block ➊ Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the cat. no. (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Cat. No. 1492-CABLE005A is for a 0.5 m cable for the 1746-IA16 I/O Module. Also refer to Build-to-Order Length Cables on page 19.
PanelConnect Module for Sensor Connection 31 Digital Cable Specifications, Continued Pinouts Digital/Analog Programmable Controller Wiring Systems Digital Pre-Wired Cables The following diagrams illustrate how the individual conductors in the digital pre-wired cables are terminated at both ends. The description listed first is the wire color of the conductor connected to the removable terminal block (Bulletin 1746, 1756, and 1769 I/O) or wiring arm (1771 I/O). The number that follows in parentheses is the corresponding pin number of the PanelConnect mating connector. Base Color Stripe Color Blue (24) (12) White/Green (22) (18) NC 20 or 40 Pin Number Black (23) (9) White/Red (19) Twisted Pair No Connection Individual Conductor Jumper Wire I/O Pin Definition 1 19 2 20 20-Conductor Cable PanelConnect Mating Definition AB Spares
32 PanelConnect Module for Sensor Connection Digital Cable Specifications, Continued Pinouts Digital/Analog Programmable Controller Wiring Systems Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19) Red RTB Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Red/Green (20) Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19) Blue RTB Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Red/Green (20) 1492-CABLE➊A 1492-CABLE➊B Black (1) White (2) Blue/Red (19) Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) Orange/Black (10) Blue/Black (11) Black/White (12) Red/White (13) Green/White (14) Blue/White (15) Black/Red (16) White/Red (17) Orange/Red (18) Red/Green (20) A B C D 00 01 02 03 04 05 06 07 10 11 12 13 14 15 16 17 E Green (4) Blue (6) Red/Black (8) Orange/Black (10) 2 1 20 19 Red (3) Orange (5) White/Black (7) Green/Black (9) Black (1) White (2) Black/White (12) Blue/Black (11) Green/White (14) Red/White (13) Black/Red (16) Blue/White (15) Orange/Red (18) Blue/Red (19) White/Red (17) Red/Green (20) 1492-CABLE➊F 1492-CABLE➊X Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Blue/Red (19) Red/Green (20) 2 4 6 8 10 12 14 16 18 1492-CAB➊A69 1 Red (3) 3 Orange (5) 5 White/Black (7) 7 Green/Black (9) 9 Blue/Black (11) 11 Red/White (13) 13 Blue/White (15) 15 White/Red (17) 17 Black (1) White (2) Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Blue/Red (19) Red/Green (20) 2 4 6 8 10 12 14 16 18 1492-CAB➊B69 1 Red (3) 3 Orange (5) 5 White/Black (7) 7 Green/Black (9) Black (1) 9 White (2) 11 Blue/Black (11) 13 Red/White (13) 15 Blue/White (15) 17 White/Red (17) ➊ Cables are available in standard lenghts of 0.5 m, 1.0 m, and 5.0 m. To order, insert the desired length code in the catalog number ( 005 = 0.5 m, 010 = 1.0 m, 0.25 = 2.5 m, and 050 = 5 m). Example: 1492-CABLE005B is for a 0.5 m cable for the 1746-IB16 I/O module.