EyeBall Camera 1080P Mini Wifi Spy Camera Quick Start Guide
Enji EyeBall Cam 1080P Mini Wifi Spy Camera This manual describes how to use a 1080P Enji EyeBall Mini Hidden Spy Camera and install the supplied software. Be sure that you have read and understood its contents before using the camera. To get started, you need: 1. A wireless router, its network name, and password if necessary. (NOTE: Router accepts only 2.4 Ghz. Use numbers and letters in creating network name and password.) 2. A smart device, such as an Android Smart Phone or Tablet (Android version 4.0 or latest) or an iphone, ipad, or ipod Touch (ios version 6.1 or later). PARTS & CONTROLS
CHARGING Before use, fully charge the built-in rechargeable lithium battery first for about 2 hours. The camera works even while charging. Notes: Red LED light is on while charging, once fully charged, red LED light turns off. If image is not clear, this means the battery is low. Charge the battery first for 2-3 hours. Battery life is about 60 minutes. POWER ON / POWER OFF Press ON/OFF button once to power the camera on. To power off, press and hold the ON/OFF button for 5 seconds. The red and yellow indicators will turn off.the Camera is now off. INDICATORS & MODES After connecting the battery/charger to the camera, press the ON/OFF button to power on the camera. 1. Red LED indicates that the camera is charging. 2. P2P(AP) mode: Blue LED lights on, yellow LED flashes slowly 3. Remote IP Mode: Blue LED lights on, yellow LED flashes quickly for a few seconds then always stays ON NOTES: 1. Once you have configured remote IP mode, yellow LED is lighted and stays ON. Under any mode, the camera can be reset to P2P Mode. 2. Press the reset key about 5 seconds until all lights go OFF, if the camera boots up again, reset is successfull (about 30 seconds).
APP DOWNLOAD MUCAM Picture 1 Picture 2 1. Scan the QR (picture 1) code directly to the download interface (picture 2). 2. Select and download software according to your mobile phone system. *You can also download the App Mu Cam from Google Play Store (for Android) or Apple Store (for ios). Or open the link to download the APP. APP Download Link : http://112.124.40.254:808/app_dwn/mucam.html CONNECTING TO WIFI P2P Mode Connection (Point to Point) 1. To connect to your smartphone s hotspot connection, search for your phone s WIFI signal and tap to connect network with the camera UID (which is unique to each unit), as shown in the image below:
Please note that when connected to your phone s hotspot, camera can t be controlled remotely when phone s WIFI signal is out of camera range. If there is no hotspot Wifi, please reset the camera. 2. Then Open the phone App (Mu Cam). This signal is the machines UID which is different for each machine. Click on the icon to add into the camera as shown below:
The default password is 8888. If you forget the new password, please reset the camera.
3. Click to go online. The camera appears as shown below:
Remote IP Mode Connection 1. Click on the small gear icon 2. Enter advanced configuration as shown in image. 3. Find the installation location of the signal router, configure the camera to enter the password into the router as shown in the image. NOTE: If you have 2.4 and 5.0Ghz dual Wi-Fi on your router, please select 2.4Ghz. Network name and password accepts numbers and letters only.
4. Wait for the camera to restart. It takes about 40 seconds, then the camera will show online. You can now remotely access your camera wherever there is WIFI connection available either in the same network which is a local area network, or any other phone hotspot. APP will automatically reconnect the camera once it is connected to WIFI. You can now watch the video on your own smartphone. Adding A New Online Camera 1. If the camera is already connected to a network (remote IP Mode), you need to select add new online camera to add the online camera to your smart phone, as shown below:
2. Input the UID number (you also can scan the camera QR Code to get the UID number), then input new password if changed. The default password is 8888. If you forgot the new password, just reset the camera. Click OK to add camera to the device list Computer Software Download 1. Open Link: http://112.124.40.254:80 8/app_dwn/MuCam.html 2. Download and install the software IP Camera Search Tool ( only works in same area network ) 3. IPCMultiView ( for remote control )
Adding Camera to IPC Multi View Camera must be connected to a network first. (For more details, please refer to page 7-9). Run IPC MultiView Setup EN on your Computer. The Username is admin and NO password is required. 1. Click Camera Setup or 2. To add camera to PC, Click +, input the camera name, camera s UID (located at the bottom of camera), and password (Default password is 8888), then click OK. 2.1. If the camera and PC is in LAN, just click to search the camera s UID, then click the camera s UID and OK. 2.2. Click - to delete camera from the device list. 3. Double click the camera name at the bottom right corner or connect the camera.
4. After connecting, click these icons to use the camera functions. Click Settings icon to finish settings. Adding Camera to IP Camera Search Tool 1. View in Web Browser 2. Camera must be connected to network first. (For more details, please refer to page 7-9). 3. Make sure the Computer and camera are connected to the same WiFi network. 4. Run IP Camera Search Tool on your computer. 5. Click IP Camera Search Tool icon. 6. You can see the camera item list in the camera list. You can visit camera only in the local area network (LAN) on Computer. 7. Double click IP address, the Username is admin and no password is required. If your PC does not install the player plug-ins, please click to download and install. 8. After installing the player plug-ins, click Browser plug-ins you can view the camera real-time video on your computer via Website.
You can also click the settings icon to see more information.
SPECIFICATIONS Pixel 2.0 MP Video Resolution 1080P/720P/VGA Frame 25 Visual Angle 120 degree Motion Detection Shooting Straight line 6 meters Compressed Format H.264 Recording Range 5 m² Storage Temperature -20-80 degree centigrade Operating Temperature -10-60 degree centigrade Operation Humidity 15-85%RH Memory Card Type Max 128GB (Fat.) Player Software VLC Player/SM Player Mobile Phone Operating Android / IOS System Computer Operating Windows/Mac OS X System Web Browser IE7 and above, Chrome, Firefox, Safari,etc. Maximum User 4
FREQUENTLY ASKED QUESTIONS What Micro SD Card is required for recording? Why can t I use my Micro SD Card for recording? The camera supports up to 128 GB Micro SD card. Please use High Speed Class 10 FAT formatted memory card. Original SanDisk and Kingston brands are most preferred. You must format the Micro SD before using. If SD card is not recognized when inserted into camera, just remove and re-insert. Why does my computer or security software say the software is dangerous and it is a virus? Just ignore the warning and continue. Why can t the camera go online? 1. Powerless, please charge the battery or connect the camera while charging. 2. Check if your router is working properly or not. 3. Check your signal, your device may not be connected to Wi-Fi due to weak Wi-Fi signal. 4. Please check your network name and password to see if it includes special symbols. 5. Check if your Wi-Fi setting is correct or not, correct password may be needed. How can I record videos in the Micro SD card? Insert a memory card in the camera and open the setting menu to set SD card video recording. Why is remote monitoring not smooth? You should choose a suitable resolution to watch according to your internet speed.
Why I can t save to my SD card? SD Card must be formatted if this is your first time to use it. How do I change my password? Press reset key for 10 seconds and restore the factory setting. EyeBall Camera 1080P Mini Wifi Spy Camera For more info email us at: info@enji-prime.com OR visit our website: www.enji-prime.com