SW-IM-709 DISTINCTIVE FEATURES Snap-action : tactile feedback with audible click High current/voltage rating Sealed to IP67 Flat round actuator for optional marking NO+NC ENVIRONMENTAL SPECIFICATIONS Front panel sealing : IP67 according to IEC 6059 Shock resistance : 50 g - ms according to IEC 68--7 Salt spray : IEC 5-6, test f Operating temperature : -0 C to +85 C (-0 F to +85 F) Storage temperature : -0 C to +85 C (-0 F to +85 F) ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : A 8 VDC Initial contact resistance : 00 mω max. Insulation resistance : GΩ min. at 500 VDC Dielectric strength : 500 Vrms between terminals Electrical life at full load : 5,000 cycles GENERAL SPECIFICATIONS Panel thickness :.5 mm (.059) to 0 mm (.9) Total travel :.7 mm (.067) ± 0. mm Low level or mechanical life :,000,000 cycles Torque (applied to nut) : Nm max. with metal nut U66.5 Nm max. with plastic nut U8 MATERIALS Case : polyamide /6 Actuator : polyamide 6/6 Bushing/bezel : polyamide 6/6 Contacts : silver, gold plated Terminal seal : epoxy The company reserves the right to change specifications without notice. B
AGENCY APPROVAL A 5 VAC/50 VAC File E88 MOUNTING STANDARD BEZEL (CONTINUED) BACK OF PANEL SPACE REQUIREMENT Availability : consult factory for details of approved models. Marking : to order switches marked UL, complete appropriate box of ordering format. PANEL CUT-OUT.90 (.507).50min-0.00Max (.059MIN.-.9MAX.) Ø.60 (.55DIA) Ø.50 (.5DIA) - Flat seal MATRIX MOUNTING 0.00 0.00 0.00 0 TERMINALS.70 (.6).00 (.09) Straight P.50 (.8) CIMCP 7.60 (.99) (.0).0 (.09).0 (.07) Quick-connect Z CIM PANEL CUT-OUT MOUNTING REDUCED BEZEL.90 (.507) 0.80min-.0Max (.0MIN.-.69MAX.).50min-0.00Max (.059MIN.-.9MAX.) ELECTRICAL FUNCTIONS Ø.60 (.55DIA) 7.50 7.50 (.689) (.689) Ø (.96) Ø5.60 (.6DIA) Ø.50 (.5DIA) - Flat seal Function 7 () MATRIX MOUNTING MOUNTING STANDARD BEZEL 7.50 (.689) BACK OF PANEL SPACE REQUIREMENT - O-ring 0 B
BUILD YOUR PART NUMBER BASIC PART NUMBER IM SERIES ACTUATOR SHAPES ELECTRICAL FUNCTION TERMINALS CONTACTS R P Round, curved Round, flat 7 NC + NO P Z Straight PC Quick-connect Silver, gold plated (standard) Actuator marking available on round flat models (symbol 0 mm max.). On request. OPTIONS ACTUATOR COLORS BUSHING & BEZEL BEZEL OPTIONS ACTUATOR OPTION APPROVAL Blue B Dark blue Black Black Other : on request Standard bezel Dia. 5 (.590) reduced bezel, front mounting Std actuator 0 High actuator UL Consult factory for detail of approved models. Green Grey Dia. 5 (.590) reduced bezel, std mounting 5 Yellow 6 Red 7 White 9 Orange ABOUT THIS SERIES On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart. Notice : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand (P/N U55). See "Sealing Boots" section of website. Mounting accessories : Standard hardware supplied : flat seal (standard bezel) or O-ring (reduced bezel) and metal hex nut mm (.55) across flats. Hex nut part number U66. Plastic nut 7 mm (.669) across flats, thickness mm (.57) available on request. Part number U8.
Flat actuator Ø.00 (.7DIA) 0.80 (.5) Ø.00x0.75SI (.7DIAx0.75IS) 0.50 (.00).5 (.).00 (.09) (.0).5 (.) FLAT CIMR7P Ø.00 (.7DIA).00 (.078) (.96) STANDARD BEZEL QUICK-CONNECT TERMINALSCIRSH.50 (.8) EPOXY IMP7P Ø7.50 (.688DIA).70 (.6) (.96) IMR7P 8. (.7) Curved actuator Common terminal identified by a horizontal dash.00 (.078) FLAT STANDARD BEZEL STRAIGHT PC TERMINALS Ø7.50 (.688DIA) Page 0--- Curved actuator CIRSH 0.80 (.5) Ø.00x0.75SI (.7DIAx0.75IS) Page 0--- CIMR7P IMP7Z 0.50 (.00).5 (.).0 0.9 Ech (.07).5 (.) 7.60 (.99) EPOXY Flat actuator.0 (.09) IMR7Z.00 (.866) (.0) LE 8/0/0 CIMR7Z CIRSH B 5 6 7 9 ACTUATOR COLORS Page 0--- CIRSH Blue Dark blue Black Green Grey Yellow Red White Orange Page 0--- CIMR7Z Ech 0.9 LE 8/0/0 BUSHING AND BEZEL Black (standard) Other : on request
BEZEL OPTIONS Ø (.96) Ø (.96) Standard bezel Dia. 5 (.590) reduced bezel, mounting of the switch from the front into a threaded panel cut-out Dia. 5 (.590) reduced bezel, standard mounting CIM ACTUATOR OPTION Standard actuator High actuator Ø.00 (.7DIA) Ø.00 (.7DIA).70 (.85) 0.70 (.85) CIM Ech 0.9 0 IMR 0 IMP LE 8/0/0 AGENCY APPROVAL UL Availability : consult factory for details of approved models. Marking : to order switches marked UL, complete appropriate box of ordering format. 5