Cisco 642-035 Troubleshooting Cisco Data Center Unified Computing Download Full Version : https://killexams.com/pass4sure/exam-detail/642-035
QUESTION: 154 HOTSPOT
Answer:
QUESTION: 155 Which command output shows the interface assigned as the designated receiver of each VLAN? A. show system vlan reserved B. show vlan internal bd-info bd-to-vlan all-bd C. show port internal info all D. show platform software enm internal info vlandb all Answer: D QUESTION: 156 Which option describes how you can reset the BIOS password of a Cisco UCS C- Series Rack-Mount Server? A. Turn off the server. Press and hold the F7 key, and then turn on the server. B. Reset the jumper on the motherboard. C. Press and hold the power switch for 20 seconds. D. Turn off the server. Press and hold the F2 key, and then turn on the server. Answer: B QUESTION: 157 Which three components are updated using the Host Upgrade Utility? (Choose three.)
A. BIOS B. Network Adapter(s) C. Array Controller D. Cisco IMC E. LOM port F. UCSM G. Drive Firmware Answer: A, B, D QUESTION: 158 Which two types of ports does end host mode switching have? (Choose two.) A. VSS B. border C. router D. server E. STP F. client Answer: B, D QUESTION: 159 You have a Cisco UCS Fabric Interconnect in Fibre Channel end-host mode. You must check whether all of the Fibre Channel targets are available through the fabric interconnect at VSAN 200. Which command must you use? A. show npvflogi-table B. show flogi-table C. show flogi database D. show zoneset active VSAN 200 Answer: A QUESTION: 160 Refer to the exhibit.
Which tab would be the most useful for troubleshooting a blade discovery problem? A. Faults B. Events C. FSM D. Servers Answer: C QUESTION: 161 At any given time, each server can be associated with how many service profiles? A. 1 B. 2 C. 5 D. 10 E. unlimited Answer: A QUESTION: 162 Which two options are ways to identify the exact BIOS version of a Cisco UCS C- Series Rack-Mount Server? (Choose two.) A. Use the iflash32 command and select the -i option. B. Press F2 during server bootup. C. Press F6 during server bootup. D. Press F12 during server bootup. E. Press F10 during server bootup. F. Use the EFI interface. Answer: A, B QUESTION: 163 Which two areas should you investigate when experiencing problems with the UCS Manager KVM? (Choose two.) A. Java complications
B. network complications C. server CPU type D. Fabric Interconnects hardware E. SSD complications Answer: A, B QUESTION: 164 During the installation of Windows 2008 64-bit operating system on a Cisco UCS server, the RAID controller is not found. What is the cause of the problem? A. The Cisco IMC firmware needs to be updated. B. The LSI option ROM needs to be configured by pressing Ctrl-H during post. C. The LSI drivers are not bundled and need to be loaded by clicking the Load Driver option to point to the correct drivers. D. Windows 2008 64-bit operating system is not supported on Cisco UCS servers. Answer: C QUESTION: 165 HOTSPOT
Answer:
QUESTION: 166 Which four tasks can be performed via Cisco IMC remote access to a Cisco UCS system? (Choose four.) A. power cycle the server B. deploy an operating system C. toggle the locator LED D. configure the boot order E. view properties and sensors F. configure the hypervisor G. enable Cisco UCS Manager Answer: A, C, D, E QUESTION: 167 While updating firmware in a Cisco UCS environment, what will the Cisco UCS Manager do? A. show you all versions available on Cisco.com B. show you all versions downloaded to the Cisco UCS Manager C. show you only versions that are supported in your environment D. show you only versions that you selected to show E. show you old and new versions from your download Answer: C
For More exams visit https://killexams.com Kill your exam at First Attempt...Guaranteed!