lumenfacade Specification Sheet Client Project name Order# Qty Type FEATURES AND BENEFITS Physical : Low copper content extruded aluminum housing Available in 1, 2, or 4 sections Electro-statically applied polyester powder coat finish Machined aluminum s and silicone gaskets Stainless steel hardware Clear tempered glass Asymmetric wallwash, 10 x 10, 10 x 60, 0 x 60 or 60 x 60 optics Right or left feeding side options available IP66 IK07 rated (asymmetric wallwash lens is IK06 rated) Meets G ANSI C16.1 Vibration standard for bridge applications Corrosion-resistant coating for hostile environments** CERTIFICADO No.054, 055 RETILAP IK07* Performance : CRI values: 5+ (2700K), 0+ (000K), 7+ (4000K) Lumen maintenance 120,000 hrs [L70 @ 25 C] Lumen measurements comply with LM - 79-0 standard Resolution per foot or per fixture (configured with LumenID V software & DMX/RDM) Operating temperatures: -25 C to 50 C [-1F to 122F] Delivered Intensity 4ft HO 4000K Output [lm] [peak cd] Electrical : Line voltage luminaire for 100 to 277V Power and data in 1 cable () Up to feet with a single120v power feed, HO version 5W/ft version meets ASHRAE standards for linear lighting on building facades.5w/ft Regular Output version 15.25/ft High Output version Dimming options: 0-10 volt, DMX/RDM enabled, DALI, Lumentalk or Lutron EcoSystem enabled 1 " [40mm] 2" [51mm] 1" 4 [7mm] Minimum spacing 4" [102mm] 10ºx10º - - 10ºx60º,692 19,654 0ºx60º*,54 4,750 60ºx60º*,676,17 WW,592 5,159 *Estimated.Consult lumenpulse website for the latest ies files. 25 ",7 ",49 " [645mm, 949mm, 1254mm] MALE INPUT CONNECTOR " 216 [56mm] FRONT VIEW *Asymmetric wallwash lens is IK06 rated. ** Use only when exposed to salt spray and harsh chemicals. This option is not required for normal outdoor exposure! 1/11 45 " 16 [110mm] 21 " [54mm] SIDE VIEW Consult
ASYMMETRIC WALLWASH OPTIC FEEDING SIDE DETAIL Wall side Wall side INPUT INPUT WW-LF Asymmetric Wallwash Optic, Left Feed WW-RF Asymmetric Wallwash Optic, Right Feed Always position frosted side toward the wall *Fixture s feeding side is based on uplight installations. Feeding sides are reversed when fixture is used in a downlight application. Recommended setback from wall is 1/10 of the wall height. Example: 2ft setback for a 20ft wall. FRONT VIEW RIGHT SIDE VIEW (Fixture pointing upwards) 2/11 Consult
FEEDING SIDE POWER IN RIGHT *Fixture s feeding side is based on uplight installations. Feeding sides are reversed when fixture is used in a downlight application. FRONT VIEW RF Right Feeding side fixed mounting shown RIGHT (Fixture pointing upwards) POWER IN LEFT FRONT VIEW LF Left Feeding side fixed mounting shown LEFT (Fixture pointing upwards) /11 Consult
lumenfacade Specification Sheet MOUNTING OPTIONS /4 [19mm] / [10mm] UMP Fixed Mounting /16 [5mm] 1/2 [9mm] 10 2 7/ [7mm] 2X 9/2 THRU ALL UMAS Universal Adjustable Mounting 90 UMP Mounting Hole Pattern 0 45º /4 [19mm] WAMH6 Adjustable Extended Arm Mounting 6" Horizontal version / [10mm] 0º / [10mm] 2 1/2 [64mm] 1 /4 [45mm] -45º 2X 9/2 THRU ALL 45º WAMH12 Adjustable Extended Arm Mounting 12" Horizontal version UMAS Mounting Hole Pattern 0º -45º / [10mm] 45º WAMH1 Adjustable Extended Arm Mounting 1" Horizontal version 2 1/2 [64mm] 0º 1 /4 [44mm] 2X 1/4 THRU ALL -45º WAMH Mounting Hole Pattern 0 9" 6" 16 [152mm] [90mm] 4/11 12" [05mm] 1" [457mm] Consult
LOUVER ACCESSORY INSTALLATION DETAIL Not suitable for asymmetric wallwash optic Blade spacing 1" [25mm] 1 9 16 ", 25 9, 7 9 16 " 16 ", 49 9 16 " [44mm, 649mm, 954mm, 125mm] 4" [102mm] 2 " [60mm] FRONT VIEW Blade depth 7 16 " [11mm] 4 1 2 " 2 1 " [114mm] [54mm] SIDE VIEW LOGHRD Radial Louver for Lumenfacade Horizontal (2 mounting screws included) (see page 6 for ordering code) OPTION ETE - End-to-end configuration, no jumper cable needed. 16 cable included at input. 5/11 Consult
ACCESSORIES Order separately Control Systems: LTO2 Lumentouch is a wall mount DMX 512 controller keypad. LCU Lumencue is a USB / mini SD DMX 512 controller. LID LumenID is a diagnostic and addressing DMX 512 controller. It must be specifi ed on all DMX applications. Refer to LID specifi cation sheet for details. LTN Lumentone is a simple pre-programmed DMX 512 controller with a push button rotary dial and live feedback. Control Boxes: CBX DMX/RDM control box. Up to six power and data outputs to fi xtures or fi xture runs. Ethernet enabled option. Refer to CBX specifi cation sheet for details. Leader Cable : LOGLCD LOGLCD -ETE Leader Cable for Lumenfacade. Please add desired cable length : 10, 25 or 50 [m, 7.6m or 15.2m] standard lengths endcap is mandatory for any unused connector. (1) included with every leader cable Leader Cable for Lumenfacade, ETE option. Please add desired cable length : 10, 25 or 50 [m, 7.6m or 15.2m] standard lengths endcap is mandatory for any unused connector. (1) included with every leader cable Jumper Cable : LOGJCD LOGJCD -ETE Jumper Cable for Lumenfacade. Please add desired cable length : 2 or 4 [0.6m, 1.2m] standard lengths Jumper Cable for Lumenfacade, ETE option. Please add desired cable length : 2 or 4 [0.6m, 1.2m] standard lengths Radial Louver : Not suitable for asymmetric wallwash optic LOGHRD - Radial louver for Lumenfacade Horizontal. Louver blade depth: 7/16 [11mm]; louver blade spacing: 1 [25mm] 1. Please specify desired nominal length: 1, 2, or 4. 2. Please specify finish as BK - Black Sandtex, SI - Silver Sandtex, or WH - Smooth white (Custom color available on request, please specify as CC together with RAL color : ) 6/11 Consult
RESOLUTION DETAILS Applicable for DMX/RDM control option only. Fixture resolution can be configured on-site within the LumenID V software. A DMX/RDM enabled CBX is required. Resolution per foot: each foot is addressed independently DMX ADDRESSES: 1 2 4 5 6 7 LOGH 4 inches LOGH 4 inches Resolution per fixture: each fixture is addressed independently DMX ADDRESSES: 1 2 LOGH 4 inches LOGH 4 inches 7/11 Consult
TYPICAL WIRING DIAGRAMS Non-Dimming or Lumentalk Dimming Version 1% minimum dimming value for Lumentalk dimming American CE USE Green Yellow/Green Ground Black Brown Live 100-277V White Blue Neutral Red/Purple Black 0-10V / Data + Orange Grey 0-10V / Data - #16 #16 JBOX #16 Maximum run length by 15A circuit - Lumenfacade horizontal HO Cable length/voltage 120V 240V 277V ft 100ft 112ft 6ft 76ft 4ft Maximum run length by 15A circuit - Lumenfacade horizontal RO 14ft 16ft 14ft 120ft 12ft 14ft ASHRAE Code Compliant - Lumenfacade Horizontal 5W/ft Maximum run length by 15A circuit 100-277V Line black Ground green Neutral white Wire-nuts 10ft 250ft 00ft 16ft 20ft 20ft Junction box (by others) Notes: 1 Maximum run length calculations are typically based on 4ft fixtures. 2 Consult factory for specific applications. From dimmer Dimming Version (0-10V) 10% minimum dimming value Data+ red Data-- orange 100-277V To fixtures Line black Ground green Neutral white Junction box (by others) Dimmer JBOX 0-10V /11 Consult
Open Preset Close 1 2 4 Off Specification Sheet TYPICAL WIRING DIAGRAMS - continued Dimming Version (DALI) 1% minimum dimming value American CE USE Green Yellow/Green Ground Black Brown Live 100-277V White Blue Neutral Red/Purple Black 0-10V / Data + Orange Grey 0-10V / Data - Typical DALI Controller JBOX Maximum run length by 15A circuit - Lumenfacade horizontal HO Cable length/voltage 120V 240V 277V ft 100ft 112ft 6ft 76ft 4ft From DALI Controller Maximum run length by 15A circuit - Lumenfacade horizontal RO 14ft 16ft 14ft 120ft 12ft 14ft ASHRAE Code Compliant - Lumenfacade Horizontal 5W/ft Maximum run length by 15A circuit 10ft 250ft 00ft 16ft 20ft 20ft Notes: 1 Maximum run length calculations are typically based on 4ft fixtures and up to 64 DALI or EcoSystem enabled fixtures per run. 2 Consult factory for specific applications. Each fixture requires 1 DALI or Lutron EcoSystem address. Dimming Version (EcoSystem )* 1% minimum dimming value Junction box (by others) From Lutron EcoSystem Controller Data+ red Data-- orange 100-277V To fixtures Line black Ground green Neutral white Data+ red Data-- orange 100-277V To fixtures Line black Ground green Neutral white Junction box (by others) JBOX LUTRON Grafik Eye shown *Each Lutron EcoSystem enabled fixture has its own address; for the example shown above, there are a total of EcoSystem addresses. 9/11 Consult
TYPICAL WIRING DIAGRAMS - continued Daisy Chain Layout (DMX/RDM) 1% minimum dimming value American CE USE Green Yellow/Green Ground Black Brown Live 100-277V White Blue Neutral Red/Purple Black 0-10V / Data + Orange Grey 0-10V / Data - Lumentouch 2.0 CBX 100-277V Data input 100-240V Maximum run length by 15A circuit - Lumenfacade Horizontal HO DMX/RDM Cable length/voltage 120V 240V 277V CBX 100-277V Data input ft 100ft 112ft 6ft 76ft 4ft Maximum run length by 15A circuit - Lumenfacade Horizontal RO DMX/RDM 12ft 12ft 12ft 120ft 12ft 12ft ASHRAE Code Compliant - Lumenfacade Horizontal 5W/ft DMX/RDM Maximum run length by 15A circuit 12ft 12ft 12ft 12ft 12ft 12ft Notes: 1 Maximum run length calculations are typically based on 4ft fixtures and up to 2 DMX/RDM enabled fixtures per DMX/RDM run. 2 Consult factory for specific applications. Each fixture requires 1 DMX address. 10/11 Consult
HOW TO ORDER LOGH 1 2 4 5 6 7 9 10 1 Housing: LOGH ASHRAE - Lumenfacade Horizontal, 5W/ft ASHRAE compliant LOGH RO - Lumenfacade Horizontal Regular Output,.5W/ft LOGH HO - Lumenfacade Horizontal High Output, 15.25W/ft 6 Feeding Side: Please specify one of the following: (Right Feeding side is standard unless otherwise specified.) LF - Left Feeding side RF - Right Feeding side 2 Voltage: 7 Mounting Option: Length: 100-100 volts 120-120 volts 20-20 volts 220-220 volts 240-240 volts 277-277 volts UMP - Fixed Mounting 2 UMAS - Universal Adjustable Mounting 2 WAMH6 - Adjustable Extended Arm Mounting 6 Horizontal version WAMH12 - Adjustable Extended Arm Mounting 12 Horizontal version WAMH1 - Adjustable Extended Arm Mounting 1 Horizontal version 12-1 / inches (40mm) (2 kg/4.5 lbs) 24-25 / inches (645mm) (.17 kg/7 lbs) 6-7 / inches (949mm) (4.75 kg/10.5 lbs) 4-49 / inches (1254mm) (6.5 kg/14 lbs) 4 Colors and Color Temperatures: 5 Optics: 27K - 2700K 0K - 000K 5K - 500K 40K - 4000K RD - Red GR - Green BL - Blue WW - Asymmetric Wallwash optic 10x10-10 x 10 1 10x60-10 x 60 0x60-0 x 60 60x60-60 x 60 Finish: 9 Control: 10 Option: BK - Black Sandtex SI - Silver Sandtex WH - Smooth white CC - Custom color and finish (please specify RAL color) NO - No dimming LT - Lumentalk Dimming 4 DIM - 0-10V Dimming option 5 DMX/RDM - DMX/RDM enabled 6 DALI - DALI Dimming option 7 ES - Lutron EcoSystem Enabled Dimming ETE - End - to - end configuration, no jumper cable needed CRC - Corrosion-resistant coating for hostile environments GV - G ANSI C16.1 Vibration Rating 9 Notes: 1 For best results use with HO fixtures at a 6-inch (15cm) setback from surface. Contact factory for application support. 2 Suitable to use when GV option is specified. North American RAL colors specified with RAL number only are provided with a smooth/high-gloss finish. Please consult factory for other RAL textures and glosses, or to match alternate color charts. Final color matching results may vary. 4 1% minimum dimming value. Available for 2 RO, and 4 lengths only. 5 10% minimum dimming value. 6 1% minimum dimming value. Fixtures set to by fixture resolution. 1 DMX address per fixture. 7 1% minimum dimming value. 1 DALI address per fixture. 1% minimum dimming value. Available for 2 RO, and 4 lengths only. 1 EcoSystem address per fixture. 9 Available with UMP and UMAS mounting options only. 11/11 Consult