Sawing Solutions DoALL 4100 Series Metal Cutting Band Saw Solutions for ALL Your Sawing Needs 5505 W 123rd St Savage, MN 55378 www.doallsaws.com 888.362.5572
Solutions for All Your Sawing Needs... There is a DoALL metal cutting band saw that will meet your specific requirements. Whether you saw in a metal service center, fabrication or machine shop, tool room or in a maintenance department DoALL is the solution for all your sawing needs. The DoALL wide range of sawing machines includes: general purpose saws; vertical contour saws; miter cutting saws; and production power saws with capacities up to 32 inches in diameter. The following pages provide an overview of the DoALL standard band saw offering. How to Select & Order the Right Band Saw Use the chart on page 3 as a guide to select the right saw for typical sawing applications. Consider the following conditions in making your choice. Miter vs. Non-Miter Cuts. If material needs to be cut at any angle other than straight, choose a miter cutting band saw. Manual vs.. A manual saw does not automatically move material into a saw for cutting - the operator must manually move the material. Typically an automatic saw has an indexing section that feeds material into the sawing or cutting area. High vs. Low Production. In high production applications (6 or more hours per shift or high cutting rates) a heavy-duty saw, wide band, and more horsepower provide greater productivity and reliability. Design Capacity vs. Effective Capacity. A saw is most effective in materials from 1/3 to 2/3 of the rated size capacity. Using a 12 capacity saw is not ideal for cutting 12 solids all day. Exotic Materials vs. Mild Materials. Hard-to-cut materials, like Inconel and 316 stainless, are best cut with high production, heavy-duty machines and wide blades. Bundle Cutting vs. Two-at-a-Time. Bundle cutting is good when cutting long bundles into short bundles because it eliminates the need to break and re-strap the bundles. Cutting material two-at-a-time is often faster than bundle cutting. It also eliminates the potential of bars spinning and can be done on a smaller, less expensive machine. Standard Machine vs. Custom. Some applications benefit from unique saws or handling systems that accommodate unusual materials, enhance safety, or boost productivity. If a standard machine just doesn t seem to fit, ask about custom sawing solutions. Budget Constraint vs. The Right Machine. Purchasing a less expensive machine may fall within your budgetary constraints, but not selecting the right machine may cost you in lost production. A DoALL representative will help you select the right machine for your application. There are financing programs also available to help you work through any budgetary constraints. 2 www.doallsaws.com 888.362.5572
Band Saw Selector For General Purpose, Miter Cutting & Production Power Machines Start Here Straight Cuts 90 Miter or Angle Cuts No Bundle Cuts Yes No Bundle Cuts Yes Manual Operation Manual Operation Manual Operation Manual Operation Low Production High Low Production High Low Production High Low Production High C-305A 12 x 12" 4 C-4100A 14 x 16" 4 C-4100NC 14 x 16" 4 DC-460NC 20 x 18" 5 DC-560NC 23.6 x 22" 5 DC-700NC 31 x 27" 5 ZV-3620 36 x 15" 7 DC-800NC 39.4 x 31.4" 5 C-305A 12 x 12" 4 C-4100A 14 x 16" 4 C-4100NC 14 x 16" 4 DC-460NC 20 x 18" 5 DC-560NC 23.6 x 22" 5 DC-700NC 31 x 27" 5 DC-800NC 39.4 x 31.4" 5 TF-1822NC 18 x 22" 6 TF-2025NC 20 x 25" 6 Low Production 500-SNC 14 x 20" 6 800-SNC 21 x 31.5" 6 TF-1822NC 18 x 22" 6 TF-2025NC 20 x 25" 6 Low Production 500-SNC 14 x 20" 6 800-SNC 21 x 31.5" 6 Low Production 400-A 10 x 16" 4 400-AV 10 x 16" 4 DC-280NC 11.75 x 11" 5 DC-330NC 15.75 x 13" 5 500-SNC 14 x 20" 6 DC-420NC 16.5 x 16.5" 5 800-SNC 21 x 31.5" 6 Manual Operation 400-M 10 x 16" 4 400-S 10 x 16" 6 C-4100M 14 x 16" 4 TF-1418 14 x 18" 6 500-S 14 x 19" 6 500-DS 14 x 20" 6 2012-VH 20 x 12" ** 2013-V 20 x 13" 7 2013-V3 20 x 13" 7 2013-V5 20 x 13" 7 2613-V3 26 x 13" 7 3612-VH 36 x 12" ** 3613-V 36 x 13" 7 3613-V3 36 x 13" 7 3613-V5 36 x 13" 7 Low Production DC-280NC 11.75 x 11" 5 DC-330NC 15.75 x 13" 5 500-SNC 14 x 20" 6 DC-420NC 16.5 x 16.5" 5 800-SNC 21 x 31.5" 6 SawType Tilt Frame TF-1822M 18 x 22" 6 TF-2025M 20 x 25" 6 C-4100M 14 x 16" 4 Manual Operation Saw Swivels/Tilts 400S 10 x 16" 6 TF-1418 14 x 18" 6 500-S 14 x 20" 6 500-DS 14 x 20" 6 TF-1822M 18 x 22" 6 TF-2025M 20 x 25" 6 Table Tilts 2012-VH 20 x 12" ** 2013-V 20 x 13" 7 2013-V3 20 x 13" 7 2013-V5 20 x 13" 7 2613-V3 26 x 13" 7 3612-VH 36 x 12" ** 3613-V 36 x 13" 7 3613-V3 36 x 13" 7 3613-V5 36 x 13" 7 ** Designates items not included in this publication. Find them at www.doallsaws.com. SawType Tilt Frame TF-1822M 18 x 22" 6 TF-2025M 20 x 25" 6 StructurALL 500-S 14 x 19" 6 500-DS 14 x 20" 6 Additional Categories Circular Saws SC-75A Up to 3" 8 SC-100A Up to 4" 8 Diamond Saws 2012-D12 20 x 12" 7 2612-D24 26 x 12" 7 2613-D36 26 x 13" 7 D-900 35 x 16" 7 www.doallsaws.com 888.362.5572 3
General Purpose Saws In machine shops, tool rooms, maintenance departments and low-volume production operations, nothing beats DoALL general purpose saws for long life, reliability and accuracy. These models will cut a wide range of materials such as tool steel, aluminum, plastic and more. Horizontal StructurALL Series 400-M 400-M 400-AV Model 400-M 400-A 400-AV Cutting Capacity Round 10-3/4" 10-3/4" 10-3/4" Cutting Capacity Rectangular 10" x 16" 10" x 16" 10" x 16" Index Stroke 22" Band Drive 2 hp 3 hp 3 hp Speed 105 to 275 fpm 50 to 400 fpm 50 to 400 fpm Blade Width 1" 1" 1" Blade Length 158" 158" 158" 1,100 lbs 1,320 lbs 1,450 lbs 1008780 1008782 1008779 Production Power Saws Production power saws are designed for cutting a wide range of metals on a production basis. They offer automatic operation and numerical control, and feature solid heavy-duty construction. This provides more rigidity and reduces vibration for higher cutting rates, exceptional accuracy, superior surface finish and increased blade life. Horizontal Series C-305A C-4100M C-4100NC Model C-305A C-4100M C-4100A C-4100NC Cutting Capacity Round 12" 16" 16" 16" Cutting Capacity Rectangular 12" x 12" 14" x 16" 14" x 16" 14" x 16" Index Stroke 24" 24" 24" Min Index Length 1/4" 1/4" 1/4" Band Drive Speed 60 to 350 fpm 40 to 360 fpm 40 to 360 fpm 40 to 360 fpm Blade Width 1-1/2" 1-1/2" 1-1/2" Blade Length 144" 186" 186" 186" 4,250 lbs 6,250 lbs 6,250 lbs 6,800 lbs CMI290197 CMI290185 CMI290186 CMI290187 4 www.doallsaws.com 888.362.5572
Production Power Saws Production power saws are designed for cutting a wide range of metals on a production basis. They offer automatic operation and numerical control, and feature solid heavy-duty construction. This provides more rigidity and reduces vibration for higher cutting rates, exceptional accuracy, superior surface finish and increased blade life. Continental Series DC-280NC DC-330NC DC-420NC DC-700NC DC-460NC DC-800NC Model Number Specification Round Cutting Capacity DC-560NC DC-280NC DC-330NC DC-420NC DC-460NC DC-560NC DC-700NC DC-800NC 11" (280mm) 13" (330mm) 16-1/2" (420mm) 18" (460mm) 22" (560mm) 27" (700mm) 31.4 *(800mm) 31" x 27" (800mm x 700mm) 39.4 x 31.4 (1,000mm x 800mm) Rectangle (WxH) 11-3/4" x 11" (300mm x 280mm) 15-3/4" x 13" (400mm x 330 mm) 16-1/2" x 16-1/2" (420mm x 420mm) 20" x 18" (510mm x 460mm) 23.6" x 22" (600mm x 560mm) Maximum (WxH) 9-3/4" x 4" (250mm x 100mm) 14-1/2" x 6-5/8" (370mm x 170mm) 14-1/2" x 7-7/8" (370mm x 200mm) 18-7/8" x 9-3/8" (480mm x 240mm) Minimum (WxH) 6-1/2" x 5/8" (165mm x 15mm) 6-1/2" x 2" (165mm x 50mm) 6-1/2" x 3-1/4" (165mm x 80mm) 9-1/2" x 3-1/4" (240mm x 80mm) Band Saw Blade x 150" x 167" 1-1/2" x 192" 1-1/2" x 209" 2" x 260" 2-5/8" x 325" 2-5/8 x 346 Band Speed 72-390 FPM (22-120mpm) 52-275 fpm (16-85mpm) Band Drive 1 Hydraulic Pump 1 hp 1 hp 2 hp 2 hp 3 hp 3 hp 3 hp Hydraulic Tank Capacity 16 Gallons (60 Liters) 16 Gallons (60 Liters) 22 Gallons (85 Liters) 22 Gallons (85 Liters) 34 Gallons (130 Liters) 34 Gallons (130 Liters) 34 Gallons (130 Liters) Coolant Tank Capacity 20 Gallons (80 Liters) 24 Gallons (90 Liters) 26 Gallons (100 Liters) 29 Gallons (110 Liters) 37 Gallons (140 Liters) 37 Gallons (140 Liters) 63 Gallons (240 Liters) 15.75" (400mm) 19.68" (500mm) 19.68" (500mm) 19.68" (500mm) 15.75" (400mm) 15.75" (400mm) 15.75 (400mm) 141.73" (3600mm) 177.16" (4500mm) 177.16" (4500mm) 177.16" (4500mm) 141.73" (3600mm) 141.73" (3600mm) 236.2 (6000mm) 27-1/2" 27-1/2" 27-1/2" 29-1/2" 33-1/2" 31-1/2" 36.2 Bundle Capacity Index Length Single Multiple Material Pass Line Height 3858 lbs. 4410 lbs. 5402 lbs. 6284 lbs. 9923 lbs. 15650 lbs. 25,350 lbs CMIDC280NC CMIDC330NC CMIDC420NC CMIDC460NC CMIDC560NC CMIDC700NC CMIDC800NC www.doallsaws.com 888.362.5572 5
Miter Cutting Saws DoALL miter cutting saws increase flexibility and improve efficiency in fabrication shops or other sawing applications that require the cutting of miters. DoALL offers a full range of saws that feature a variety of cutting capacities and angle cutting options. Horizontal StructurALL Series 400-S 500-DS 500-S Model Cutting Capacity Round - 0 Cutting Capacity Round - 45 Cutting Capacity Round - 60 Cutting Capacity Rect. - 0 Cutting Capacity Rect. - 45 Cutting Capacity Rect. - 60 Index Stroke Band Drive Speed Blade Width Blade Length 400-S 10-3/4" 10-3/4" 9" x 16" 9" x 10.75" 2 hp 105 to 275 fpm 1" 158" 1,200 lbs CMI1008780 500-S 14-3/4" 15" 8" 14" x 19" 14" x 14" 14" x 8" 50 to 400 fpm 197" 3,000 lbs CMI1009648 500-DS 15" 15" 14" x 20" 14" x 14" 14" x 8" 50 to 400 fpm 197" 2,400 lbs CMI1009650 500-SNC 800-SNC 500-SNC 14-3/4" 13" 14" x 20" 14" x 13" 14" x 9" 14" - 40" 50 to 400 fpm 197" 3,000 lbs CMI1009652 Vertical Tilt Frame Series 800-SNC 21" 16" 14" 21" x 31-1/2" 21" x 16" 21" x 14" 26-60" 70 to 400 fpm 1-1/2" 271" 10,800 lbs CMI1012048 Upright Band Mill For high production, heavy-duty applications. TF-2025M TF-1822M Model Cut. Cap. Rnd - 0 Cut. Cap. Rnd - 45 Cut. Cap. Rnd - 60 Cut. Cap. Rect. - 0 Cut. Cap. Rect. - 45 Cut. Cap. Rect. - 60 Index Stroke Band Drive Speed Blade Width Blade Length 6 TF-2025NC TF-1822NC TF-1418 TF-1418 10" 10" 8" 14" x 18" 12.5" x 14" 8" x 14" 2 hp 50 to 400 fpm 1" 157" 1,800 lbs 225040 TF-1822M 18" 15" 10-1/4" 18" x 22" 15" x 18" 10-1/4" x 18" 65 to 385 fpm 195" 2,800 lbs 1003538 TF-1822NC (APC) 17-1/2" 13" 18" x 22" 18" x 13" 17-1/2" 5" to 40" 7. 65-385 fpm 179" 7500 labs 1003539 TF-2025M 20" 17" 11" 20" x 25" 17" x 20" 11" x 20" 50 to 300 fpm 209" 7,200 lbs 590043 TF-2025NC 20" 17" 11" 25" x 20" 17" x 20" 11" x 20" 5" to 40" 50 to 300 fpm 209" 10,450 lbs 590042 www.doallsaws.com 888.362.5572 2618 Model Cutting Capacity Cutting Capacity Round Band Drive Speed Blade Width Blade Length 2618-4 26" x 18" 18" 7. 40-300 fpm 3/8" to 1-1/2" 206" 6,600 lbs 1009044
Vertical Saws Among the most versatile machines available, vertical contour saws cut aluminum, brass, copper, mild steel, tough tool steel, stainless steel and sheet metal as well as nonmetals like plastics, paper and fibrous materials. Plus, they re available with a wide variety of attachments for contour cutting, miter cutting, disc cutting and more. Contour Series 2013 2613 3613 Model 2013-V 2013-V3 2013-V5 2613-V3 3613-V 3613-V3 3613-V5 Cutting Capacity Rectangular 20" x 13" 20" x 13" 20" x 13 26" x 13 36" x 13 36" x 13 36" x 13 Cutting Capacity Round 13" 13" 13" 13" 13" 13" 13" Band Drive 2 hp 3 hp 3 hp 3 hp 3 hp Speed 55-300/960-5,200 fpm 30-320/550-5,500 fpm 550-5,500 fpm 30-320/550-5,500 fpm 55-300/950-5,200 fpm 30-320/550-5,500 fpm 550-5,500 fpm Blade Width 1/8" to 1" 1/8" to 1" 1/8" to 1" 1/8" to 1" 1/8" to 1" 1/8" to 1" 1/8" to 1" Blade Length 154" 154" 154" 185" 199" 199" 199" 1,250 lbs 1,250 lbs 1,250 lbs 1,400 lbs 1,550 lbs 1,550 lbs 1,550 lbs CMI290166 CMI290184 CMI290207 CMI1003536 CMI290221 CMI290215 CMI290216 Ask about these and other accessories for your vertical band saw! Mitre Attachment High Contour Glide Table HMD Power Feed Tables and Diamond Saws Zephyr Series - Diamond Series - Vertical ZV-3620 Model ZV-3620 Cutting Capacity Rectangular 36" x 15" 20" Round Max Work Height Under Guide 20", at Column 15" Band Drive 1 Speed Specify: 1,000 to 4,400, 4,000 to 8,000 or 10,000 to 15,000 fpm Blade Width 1/8" to 1" Blade Length 232" - 240" 3,000 lbs CMI490003 2012-D12 2612-D24 2613-D36 Model 2012-D12 2612-D24 2613-D36 D900 Cutting Capacity Rectangular 20" x 12" 26" x 12" 26" x 13" 35" x 16" Max Work Height 12" 24" 13 16" Band Drive 1 Speed 550 to 5,500 fpm 550-5500 fpm 1000-4000 fpm 1000-5000 fpm Blade Width 1" 1/2" - 1" 1/2" - 3/4" 1.25" Blade Length 154" 154" 186" 234" 1,650 lbs 1900 lbs 2500 lbs CMI223736/1010172 Special 5003016 CMID900 D-900 www.doallsaws.com 888.362.5572 7
Circular Cut-Off/Cold Saws If you are cutting small diameters, short lengths and thousands of parts, circular cut-off saws are perfect additions to any shop. Circular cut-off saws from DoALL can provide full automation for intricate and precise cuts, saving both time and money. SC-100A SC-75A Model SC-100A SC-75A Cutting Capacity Rectangular - 90 0.39-3.15" x 0.39-3.15" 0.32-2.36" x 0.32-2.36" Cutting Capacity Round 90 0.39" to 4" 0.32" to 3" Blade Speeds 30-150 rpm 30-150 rpm Blade Length 14.2" 11.2" Blade Width 0.102" x 0.089' 0.079" x 0.069" Blade Drive Motor 1 Auto Index Length Single 0.24" to 24" 0.24" to 24" 7937 lbs 6713 lbs CMISC-100A CMISC-75A Additional Sawing Resources Have technical questions or need more information? Call SAM - The Sawing Answer Man. SAM can be reached during normal business hours at 1-888-DoALLSAW Sign up for our DoALL University training program and sharpen your skills today! Class includes: Four hour training on the elements of sawing (machine, blade, fluids). DoALL Sawing Solutions Products that are a cut above the rest! DoALL replacement and repair parts are now available 24-hours a day online at www.doallsaws.com/store 5505 West 123rd Street Savage, MN 55378 USA www.doallsaws.com 1-888-362-5572 Copyright 2015 DoAll Sawing Products. All Rights Reserved. No image(s) or part(s) from this site may be reproduced without the written permission of Continental Machines, Inc. Options, specifications and any product information is subject to change without notice or obligation. Machine safety items may be omitted for illustration purposes only -- For proper application, always read the operation manual. DoALL, StructurALL and SAM - The Sawing Answer Man are all registered trademarks of DoALL Company. DSPSSB008 10102015 www.doallsaws.com 888.362.5572