Automatic Insulating In-Line Oil Tester DTA 100 E-AD The DTA 100 E-AD is designed to measure the electric breakdown strength of liquid or gaseous insulants fully automatically. It is used in conjunction with a personal computer and the DTA 100 E-AD control software package from BAUR. Measurement routines are executed in accordance with the selected control program and the selected test standard. Features: Electromagnetic screening - nearby electronic appliances are not affected by any interference Lockable protective hood for maximum user safety Quick breakdown detection and current break time < 1 ms. Avoids formation of fibres or carbonation of mineral oils Selectable test voltages up to 100 kv rms Self-test after each switch-on Printer log for evaluation of measured data Test cell Hermetically sealed design resistant to pressure, vacuum and temperature for carrying out flow type oil tests (also available as a transportable cell) Adjustable electrode spacing Exact setting of electrode spacings in conformance with the standards (without touching with a check gauge) by means of a built-in vernier and electro-acoustic zero spacing control Simple rinsing of the test cell by key-operated triggering of a solenoid valve Available to order with stirrer
DTA 100 E-AD - measurement set-up: 1 DTA 100 E-AD oil tester with test cell 2 Personal computer (IBM-compatible XT, AT or higher) 3 Printer (IBM graphics) Block diagram: 1 2 3 F1 F2 F3 F4 F5 BAUR Oil Test System Version 1.0 MV2 Oil regenerating system MV1 Output regenerated oil F9 P DTA 100 E-AD Printer PC MV3 All the measurement and control functions are performed by the personal computer with the DTA 100 E-AD control software package from BAUR. This user-friendly measurement program offers the following selection of measurement functions: F1 withstand standard test F2 automatic standard test F3 single standard test F4 single test F5 options (select language, input report data, printer) F9 terminate (program exit) The required parameters (e.g. test standard, mean value pre-set, etc.) are entered in the respective submenus. A connected printer enables evaluation of the measurements and test data after completion of the measurement routine. Fully automatic control of a regenerating system In the measurement functions F1 (withstand standard test) and F2 (automatic standard test), the solenoid valves (MV1 - Fill, MV2 - Regenerate) of a regenerating system are controlled automatically during a measurement routine.
Interfaces on the DTA 100 E-AD: View of rear panel 8 3 4 7 1 2 6 5 Hydraulics 1 Oil inlet 2 Oil outlet 10 6 9 Electrics 3 2-pole socket "Overflow", input for external overflow sensor (e.g. a float switch) 4 2-pole plug "Alarm", output for external alarm signalling device (e.g. a flashing light or horn) 5 RS 232 interface for a personal computer 6 Appliance socket connector 7 10-pole plug X1 "Extern Valves" for external solenoid valves MV1 (Fill) and MV2 (Regenerate) Switching elements 8 Pushbutton "MV3 ON", for opening the solenoid valve MV3 (e.g. for rinsing the test cell) 9 Power switch "ON / OFF" 10 Solenoid valve MV3 (Fill test cell)
Technical data DTA 100 E-AD Power supply 110-120 V / 220-240 V (50 Hz - 60 Hz) Power consumption max. 200 VA Display backlit, 160 x 80 dot-matrix, LCD Voltage indication, digital 0-100; ± 1 kv Resolution (displayed) 0,1 kv Selectable languages German, English, French, Italian, Spanish, Dutch; other language on request Test cycles according to a standard 13 pre-programmed test standards are available: ASTM D 1816 / 97; ASTM D 877 / 87; BS EN 60156; CEI EN 60156; CSSR RVHP / 85; IEC 156 / 95; IRAM 2341 / 72; JIS C2101 / 78; PN 77 / ED 4408; SEV EN 60156; UNE 21 309 / 89; NF EN 60156; VDE 0370 part 5 / 96; Additional test cycles 5 free programmable test cycles Test voltage, testing insulants 0... 100 kv rms, symmetric Voltage rate of rise 0,5 kv / s / 1 kv / s / 2 kv / s / 3 kv / s / 5 kv / s Switch off current 4 ma Switch off time on breakdown 1 ms RBM (Real Breakdown Monitoring) detects insulating liquids with specific resistance too low ρ < 30 MΩm Relative humidity 90 not condensing Maximum ambient temperature Working: 0... + 45 C Dimensions (W x H x D) Weight Printer PC-Interface Designed and built acc. To the following standards Use Outputs 2 pole plug for "alarm" 10 pole plug for "external values" 2 pole socket for Overflow Storage: - 20... + 55 C 450 x 460 x 500 mm 37,6 kg Matrix printer, 24 char., 57 mm plain paper bi-directional RS 232, 9 pin sub D Optional: Windows PC Software Low voltage directive 73 / 23 / EWG, EN 61010-1 EMV directive 89 / 336 / EWG with modification 91 / 263 / EWG, 92 / 31 / EWG VDE 0843 part 2, IEC 801-2 / VDE 0843 part 4, IEC 801-4 VDE 0875 part 11, EN 55 011 for insulating liquids / gas with tan δ - values < 4,5 specific resistance ρ > 30 MΩm - potential-free (max. 1500 V AC ) switching capacity 250 V AC / DC; 1 A potential-free (max. 1500 V AC ) switching capacity 250 V AC / DC; 1 A + 12 V DC / 14 ma for switch open
Order instructions: Please specify in each enquiry or order: Automatic Insulating In-Line Oil Tester DTA 100 E-AD 415+038 Delivery includes: Automatic insulating in-line oil tester DTA 100 E-AD without accessories Test-Cell (test vessel)) Test-Cell 0.7 l according to IEC 156 fig. I; for insulating liquids, flow type Test-Cell 0.7 l according to IEC 156 fig. II; for insulating liquids; flow type Test-Cell 0.7 l according to ASTM D 877 for insulating liquids; flow type Test-Cell 0.7 l according to ASTM D 2477; for insulating gases; flow type Oil collecting tray PC control software for DTA 100 E-AD Cable with D socket 9 poles / D socket 9 poles Cable for external magnetic valves DTA 100 E-AD Filter plug RS 232 Setting gauge 2.5 mm IEC Mains connection cable Ink ribbon for plain paper printer - fed into printer Paper roll for plain paper printer, 57 mm width, Ø 30 mm, inserted in printer Operating manual Options: Transport case made of plywood Test-Cell 0.7 l according to IEC 156 fig. I; for insulating liquids, flow type Test-Cell 0.7 l according to IEC 156 fig. II; for insulating liquids; flow type Test-Cell 0.7 l according to ASTM D 877 for insulating liquids; flow type Test-Cell 0.7 l according to ASTM D 2477; for insulating gases; flow type Dust cover Setting gauge 1 mm Setting gauge 2 mm Setting gauge 4 mm Setting gauge 5 mm Calibrator KA 100, including software, connection cables, operating manual Consumer parts for plain paper printer: Ink ribbon for plain paper printer Paper roll for plain paper printer, 57 mm width, Ø 30 mm Mains supply: 110 V ~ to 120 V ~ 220 V ~ to 240 V ~... Included in standard delivery... Selectable (please mark with a cross or specify) Standard Selection