1
2
CALIPER Vernier Caliper - Standart Type Round depth bar (30-102) OD measurement ID measurement 530-101 Step measurement Depth measurement MT0000098 530-101 0-150MM 0.05MM - MT0000099 530-102 0-150MM 0.05MM - MT0000107 530-122 0-150MM 0.02MM - MT0000100 530-104 0-150MM(0-6 ) 0.05MM - MT0000108 530-312 0-150MM(0-6 ) 0.02MM - MT0000101 530-108 0-200MM 0.05MM - MT0002392 530-123 0-200MM 0.02MM 560-123 MT0000103 530-114 0-200MM(0-8 ) 0.05MM 560-114 MT0000105 530-118 0-200MM(0-8 ) 0.02MM - MT0000102 530-109 0-300MM 0.05MM - MT0002405 530-124 0-300MM 0.02MM 560-124 MT0000104 530-115 0-300MM(0-12 ) 0.05MM - MT0000106 530-119 0-300MM(0-12 ) 0.02MM - MT0000113 530-501 0-600MM 0.05MM - MT0000114 530-502 0-1000MM 0.05MM - With Depth Bar - * Inch/mm conversion table labeled on the back of the slider Vernier Caliper with Fine Adjustment Fine adjustment 532-101 Fine adjustment aids slider positioning MT0000123 532-119 0-130MM(0-5 ) 0.02MM - MT0000125 532-121 0-280MM(0-11 ) 0.02MM 562-121 With Depth Bar Vernier Caliper with Thumb Clamp Thumb Clamp 531-101 Slider moves only when the spring-loaded thumb grip is depressed MT0000117 531-122 0-150MM(0-6 ) 0.05MM 531-107 MT0000115 531-102 0-200MM 0.05MM - MT0000118 531-108 0-200MM(0-8 ) 0.05MM 561-108 MT0000119 531-109 0-300MM(0-12 ) 0.05MM - With Depth Bar 3
CALIPER Vernier Caliper with Carbide Jaws 530-320 OD measurement ID measurement The small venier face angle (14º) provides easy reading Step measurement Depth measurement MT0000109 530-320 0-150MM 0.05MM - MT0000110 530-321 0-200MM 0.05MM - MT0000111 530-322 0-300MM 0.05MM - Outside Point Caliper With Carbide-tipped jaw for OD 536-152 Measure wall thickness inside bores and recesses MT0000146 536-152 0-150MM 0.05MM - Outside Point Vernier Caliper Vernier Caliper with Nib Style Jaws 160-131 Radiused jaws for accurate ID measurement MT0000080 160-151 0-450MM(0-8 ) 0.02MM - With Nib Style Jaw (Fine Adjustment) MT0000239 160-131 0-600MM 0.05MM - With Nib Style Jaw MT0000081 160-153 0-600MM(0-24 ) 0.02MM - With Nib Style Jaw (Fine Adjustment) 4
CALIPER Dial Caliper Gages Internal Type External Type MT0000010 209-106 10-35MM 0.025MM 209-101 MT0000014 209-302 10-30MM 0.01MM 209-608 MT0000158 209-303 20-40MM 0.01MM 209-609 Internal Type MT0004938 209-309 80-100MM 0.01MM - MT0002374 209-404 0-20MM 0.01MM 209-601 External Type with Ball MT 0002677 209-602 0-50MM 0.05MM - Contact Point Throat depth 80mm Throat depth 170mm Dial Caliper Titanium Coating Conventional 505-671 After Sliding test comprising 100,000 movements, smooth movement over the entire measuring range assured even when you use a particular part of the sliding surface repeatedly Wear: 0 µm Wear: 4 µm MT0003345 505-671 0-150MM 0.02MM - With Depth Bar, Gray Cover MT0000027 505-683 0-150MM 0.02MM 505-601 MT0000030 505-685 0-150MM 0.01MM 505-666 MT0000028 505-684 0-200MM 0.02MM 505-602 With Depth Bar, Silver Cover MT0000031 505-686 0-200MM 0.01MM 505-667 MT0000029 505-673 0-300MM 0.02MM 505-648-50 With Depth Bar, Gray Cover Point Caliper 573-721 Narrow-tip jaws fit into very small grooves and tracks, making many previously difficult outside measurements far easier to obtain 536-121 MT0002278 573-721 0-150MM (0-6 ) 0.01MM 573-221-20 MT0000139 536-121 0-150MM 0.05MM - with Depth Bar 5
CALIPER ABS Digimatic Caliper Non Data Output Depth Rod Type 500-195-20 MT0000039 500-195-20 0-100MM (0-4 ) 0.01MM 500-135 With Depth Rod 10006482 500-181-30 0-150MM 0.01MM 500-181-20 MT0000040 500-196-30 0-150MM (0-6 ) 0.01MM 500-196-20 10012806 500-182-30 0-200MM 0.01MM 500-182-20 10006098 500-197-30 0-200MM (0-8 ) 0.01MM 500-197-20 MT0002721 500-193 0-300MM (0-12 ) 0.01MM - MT0002431 500-738-10 0-200MM (0-8 ) 0.01MM 500-177-20 ABS Digimatic Caliper with Data Output With Depth Bar 500-501-10 500-171-30 MT0004787 500-150-20 0-100MM 0.01MM 500-150 With Depth Rod MT0000042 500-151-30 0-150MM 0.01MM 500-151-20 MT0000045 500-171-30 0-150MM (0-6 ) 0.01MM 500-171-20 MT0000043 500-152-30 0-200MM 0.01MM 500-152-20 10006113 500-152-20 0-200MM 0.01MM 500-152 With Depth Bar 10006097 500-172-30 0-200MM (0-8 ) 0.01MM 500-172-20 MT0000044 500-153 0-300MM 0.01MM 500-303 MT0000047 500-173 0-300MM (0-12 ) 0.01MM 500-323 MT0000058 500-500-10 0-450MM 0.01MM 500-500-50 MT0000059 500-505-10 0.450MM (0-18 ) 0.01MM 500-505-50 MT0001779 500-501-10 0-600MM 0.01MM 500-501-50 - MT0000060 500-506-10 0-600MM (0-24 ) 0.01MM 500-506-50 MT0000061 500-507-10 0-1000MM (0-40 ) 0.01MM 500-507 Absolute Coolant Proof Caliper MT0000471 500-752-10 0-150MM (0-6 ) 0.01MM 500-672 MT0003073 500-753-10 0-200MM (0-8 ) 0.01MM 500-673 Non Data Output MT0002134 500-723-10 0-150MM 0.01MM 500-155-20 Carbide-tipped OD & ID MT0003655 500-702-10 0-150MM 0.01MM 500-600 Non Data Output MT0001918 500-724-10 0-200MM 0.01MM 500-157 Carbide-tipped OD & ID MT0003656 500-703-10 0-200MM 0.01MM 500-623 Non Data Output MT0004035 500-722-10 0-200MM 0.01MM 500-156-20 Carbide-tipped MT0004335 500-714-10 0-300MM 0.01MM 500-634 - MT0003904 500-754-10 0-300MM (0-12 ) 0.01MM 500-674 Non Data Output MT0001833 500-737-10 0-150MM (0-6 ) 0.01MM 500-175 Carbide-tipped OD & ID 6
CALIPER Absolut Solar Caliper A built-in ABS (absolute) scale means that these calipers are ready to use immediately after power-on without origin resetting just like using a vernier caliper MT0002525 500-444 0-150MM 0.01MM 500-404 With Depth bar Inside Caliper 573-642 573-146 Measure wall thickness inside bores 573-646 MT0000144 536-146 20-150MM 0.05MM - Inside Point Jaw Type MT0000069 573-646 20-150MM 0.01MM 573-146-20 Point Jaw Type MT0001881 573-642 10-200MM 0.01MM 573-142-20 Knife-Edge Type Digimatic Neck Caliper MT0000070 573-651 0-150MM 0.01MM 573-151-20 Absolute Neck Caliper Blade Type Caliper 536-136 MT0000067 573-634 0-150MM 0.01MM 573-134-20 Absolute Blade MT0001977 573-734 0-150MM (0-6 ) 0.01MM 573-234-20 Caliper MT0000141 536-136 0-300MM 0.05MM - Blade Vernier Caliper Absolute Low Force Caliper MT0003077 573-191-20 0-180MM 0.01MM 573-191-10 Low Force Type 7
DEPTH GAGES Vernier Depth Gages with Fine Adjustment Vernier Depth Gages EDP No. Part No. Range Graduation Remaks MT0000086 527-101 0-150MM 0.02MM MT0000087 527-102 0-200MM 0.02MM MT0000088 527-103 0-300MM 0.02MM - Vernier Depth Gages Hook Type EDP No. Part No. Range Graduation Remaks MT0000089 527-201 0-150MM 0.05MM MT0002455 527-122 0-200MM 0.02MM MT0000090 527-202 0-200MM 0.05MM MT0000091 527-230 0-300MM 0.05MM - Vernier Depth Gages with Fine Adjustment EDP No. Part No. Range Graduation Remaks MT0002203 527-401 0-150MM 0.05MM With Hook Type Absolute Digimatic Depth Gages MT0000093 527-302-50 0-200MM 0.05MM 527-302 - MT0000304 571-201-20 0-150MM 0.01MM 571-201-10 MT0001720 571-202-20 0-200MM 0.01MM 571-202-10 MT0000305 571-203-20 0-300MM 0.01MM 571-203-10 Depth measurement With SPC 8
HEIGHT GAGES Digimatic Height Gages Standard Type Digimatic Height Gages Multi Function Type * Optional bi-directional probe 192-007 507-302 192-663-10 MT0002086 192-613-10 0-300MM 0.01MM 192-613 MT0002315 192-614-10 0-600MM 0.01MM 182-614 MT0002087 192-632-10 0-600MM (0-24 ) 0.01MM 192-632 Vernier Gages with Adjustment Main Scale With SPC MT0002088 192-663-10 0-300MM 0.01MM 192-663 Multi MT0000641 192-664-10 0-600MM 0.01MM 192-664 Function MT0002402 192-670-10 0-300MM (0-12 ) 0.01MM 192-670 Type MT0001668 570-302 0-300MM 0.01MM 570-228 With SPC Digit Counter Type Dial Height Gages Use for height measurement with carbide tipped scribber also can mark your measurement MT0000339 514-102 0-300MM 0.02MM 514-160 MT0000340 514-103 0-300MM (0-12 ) 0.02MM 514-161 MT0000037 514-104 0-450MM 0.02MM 514-172 MT0000338 514-105 0-450MM (0-18 ) 0.02MM - MT0000342 514-107 0-600MM (0-24 ) 0.02MM 514-162 With Adjustable Scale MT0000324 192-130 0-300MM 0.01MM 192-106 MT0002085 192-131 0-450MM 0.01MM - Counter Type MT0000325 192-132 0-600MM 0.01MM 192-104 9
MICROMETER Outside Micrometer Outside Micrometer with Interchangeable Anvils MT0000719 103-129 0-25MM 0.001MM - MT0000726 103-137 0-25MM 0.01MM - MT0000720 103-130 25-50MM 0.001MM - MT0000727 103-138 25-50MM 0.01MM - MT0000728 103-139-10 50-75MM 0.01MM 103-139 MT0000729 103-140-10 75-100MM 0.01MM 103-140 MT0000730 103-141-10 100-125MM 0.01MM 103-141 MT0000731 103-142-10 125-150MM 0.01MM 103-142 MT0000732 103-143-10 150-175MM 0.01MM 103-143 MT0000733 103-144-10 175-200MM 0.01MM 103-144 MT0000734 103-145-10 200-225MM 0.01MM 103-145 MT0000735 103-146-10 225-250MM 0.01MM 103-146 MT0002488 406-250 0-250MM 0.001MM 406-521-30 MT0003759 406-251 25-50MM 0.001MM - With Ratchet Stop Non Rotating Spindle Outside Micrometer Set MT0000758 104-139A 0-100MM 0.01MM 104-139 Interchangeable Anvils 25,50,75 mm MT0000754 104-135A 0-150MM 0.01MM 104-135 Interchangeable Anvils 25,50,75,100 mm MT0000759 104-140A 100-200MM 0.01MM 104-140 Interchangeable Anvils 25,50,75 mm MT0000755 104-136A 150-300MM 0.01MM 104-136 Interchangeable Anvils 2 5,50,75,100,125 mm MT0000760 104-141A 200-300MM 0.01MM 104-141 Interchangeable Anvils 25,50,75 mm MT0000761 104-142A 300-400MM 0.01MM 104-142 Interchangeable Anvils 25,50,75 mm MT0000762 104-143A 400-500MM 0.01MM 104-143 Interchangeable Anvils 25,50,75 mm MT0000763 104-144A 500-600MM 0.01MM 104-144 Interchangeable Anvils 25,50,75 mm MT0000773 104-161A 50-150MM 0.01MM - Interchangeable Anvils 50,75,100,125 mm MT0000751 103-913-31 0-150MM 0.01MM 103-913-30 103-137, 103-138, 103-139-10, 103-140-10, 103-141-10, 103-142-10 MT0000752 103-914-31 0-300MM 0.01MM 103-914-30 All Micrometers of 103-913-30 and 103-915-30 in One Set MT0000753 103-915-10 150-300MM 0.01MM 103-915 103-143, 103-144, 103-145, 103-146, 103-147, 103-148 MT0006190 103-904-10 0-6 0.001 103-904-01 103-177, 103-178, 103-179, 103-180, 103-181, 103-182 Outside Micrometer EDP No. Part No. Range Graduation Old Code MT0000706 102-301 0-25MM 0.01MM 101-103 MT0001903 102-302 25-50MM 0.01MM 102-218 MT0000703 102-303 50-75MM 0.01MM 102-236 Digimatic Micrometer with Interchangeable Anvils Remaks With Ratchet Stop MT0000642 340-251-10 0-150MM 0.001MM 340-251 Interchangeable Anvil 0,25,50,75,100,125 mm MT0000647 340-351-10 0-150MM (0-6 ) 0.001MM 340-351 MT0000649 340-352-10 150-300MM (6-12 ) 0.001MM 340-352 Interchangeable Anvil 0,1,2,3,4,5 MT0000644 340-252-10 150-300MM 0.001MM 340-215-30 Interchangeable Anvil 150,175,200,250,275 10
MICROMETER Digit Counter Micrometer Features : - Mechanical digit counter - Equipped with Ratchet Stop for constant measuring force - Measuring faces : Carbide MT0000820 193-101 0-25MM 0.01MM - MT0000830 193-111 0-25MM 0.001MM MT0000821 193-102 25-50MM 0.01MM - MT0000831 193-112 25-50MM 0.001MM MT0000822 193-103 50-75MM 0.01MM - MT0000832 193-113 50-75MM 0.001MM MT0000833 193-114 75-100MM 0.001MM - With Ratchet Stop Digimatic Micrometer with Dust/Water Protection Coolant proof application Digimatic Micrometer with SPC Output 10012803 293-230-30 0-25MM 0.001MM 293-230 10012804 293-330-30 0-25MM (0-1 ) 0.001MM 293-330 10014451 293-231-30 25-50MM 0.001MM 293-231 With Ratchet Stop SPC 10012955 293-232-30 50-75MM 0.001MM 293-232 10012705 293-233-30 75-100MM 0.001MM 293-233 Digimatic Micrometer without SPC Output 10012805 293-240-30 0-25MM 0.001MM 293-240 10012802 293-340-30 0-25MM (0-1 ) 0.001MM 293-340 With Ratchet Stop 10014452 293-241-30 25-50MM 0.001MM 293-241 Digimatic Micrometer with 2mm/rev Spindle Feed (QuantuMike) Measuring time on a 6-stepped workpiece with one hand MT0004814 293-145 0-25MM 0.001MM - Without SPC Data Output MT0004817 293-140 0-25MM 0.001MM - With SPC Data Output Disk Micrometer Gear measuring MT0000625 123-101 0-25MM 0.01MM - With Ratchet Stop MT0000616 123-102 25-50MM 0.01MM - 11
MICROMETER Disk Micrometer-Non Rotating Spindle Type MT0000624 169-201 0-25MM 0.01MM - With Ratchet Stop Digimatic Disk Micrometer Measures root tangent length of spur gears and helical gears. MT0001938 323-250 0-25MM 0.001MM 323-511-30 Rotating Spindle MT0002095 323-251 25-50MM 0.001MM 323-512-30 MT0002675 369-250 0-25MM 0.001MM 369-511-30 Non Rotating Spindle Crimp Height Micrometer MT0000795 112-401 0-25MM 0.01MM - Vernier Crimp Height Digimatic Crimp Height Micrometer Cable crimp measurement MT0000653 342-271 0-25MM 0.001MM 342-411-30 With SPC Digital Tube Micrometer MT0002117 395-271 0-25MM 0.001MM - With SPC 12
MICROMETER Tube Micrometer Spherical Anvil Type & Cylindrical Anvils Type MT0000571 115-115 0-25MM 0.01MM - With Spherical Anvil MT0000573 115-215 0-25MM 0.01MM - With Spherical-Spherical Type Blade Micrometer Spherical Anvil MT0000801 122-101 0-25MM 0.01MM - Type A MT0000805 122-111 0-25MM 0.01MM - Type B Digimatic Blade Micrometer Measuring groove diameter of shaft MT0000880 422-230 0-25MM 0.001MM 422-111-30 Blade Type A, SPC Point Micrometer MT0000790 112-153 0-25MM 0.01MM - Point 15 MT0000794 112-213 0-25MM 0.01MM - Point 30 Non crbide tips Point Micrometer Measuring web thickness of drill MT0000790 112-153 0-25MM 0.01MM - Point 15 MT0000794 112-213 0-25MM 0.01MM - Point 30 13
MICROMETER Spline Micrometer Measuring splined shaft MT0000879 331-251 0-25MM 0.001 - Type A Gear Tooth Micrometer Ball Anvils Optional Measuring over-pin diameter of gears MT0002096 324-251-10 0-25MM 0.001MM 324-511-30 Digimatic Gear Tooth Micrometer Dial Snapmeter Measuring mass-produced parts MT0003045 523-121 0-25MM 0.001MM 523-101 Direct Go/no-Go Judgment Tubular Inside Micrometer-Single Rod Type MT0000581 133-143 50-75MM 0.01MM - Tubular Inside Micrometer, Single Rod Type Tubular Inside Micrometer - Extension Rod Type MT0000589 137-202 50-300MM 0.01MM 137-102 Extension Rod 13,25,50(2),100mm MT0000590 137-203 50-500MM 0.01MM 137-103 Extension Rod 13,25,50(2),100,200mm MT0000591 137-204 50-1000MM 0.01MM 137-104 Extension Rod 13,25,50(2),100,200(2)mm MT0000592 137-205 50-1500MM 0.01MM 137-105 Extension Rod 13,25,50(2),100,200(3),300(2)mm Interchangeable Rod Inside Micrometer Wide range of inside diameter measurement MT0000601 141-206 50-300MM 0.01MM 141-106 With 5 Rods 14
MICROMETER Digimatic Inside Micrometer MT0000698 345-250-10 5-30MM 0.001MM 345-250 Digimatic Inside Micrometer, Caliper Type Inside Micrometer Caliper Type 145-185 145-187 MT0000693 145-185 5-30MM 0.01MM - MT0000694 145-186 25-50MM 0.01MM - MT0000695 145-187 50-75MM 0.01MM - Can Seam Micrometer Inside diameter measurement Inside Micrometer, Caliper Type 147-103 147-105 MT0000812 147-103 0-13MM 0.01MM - Can Seam Micrometer for Steel Can MT0000814 147-105 0-13MM 0.01MM - Can Seam Micrometer for Aluminum Can Vernier Depth Micrometer - Interchangeable Rod Type Steel, aluminium cans measurement Wide range inside measurements MT0000888 129-109 0-50MM 0.01MM - With 2 Rods MT0000894 129-116 0-150MM 0.01MM - With 6 Rods Digimatic Depth Micrometer - Interchangeable Rod Type MT0000698 345-250-10 5-30MM 0.001MM 345-250 Digimatic Inside Micrometer, Caliper Type 15
HOLTEST Three Point Internal Micrometer EDP No. Part No. Range Graduation Old Code Remarks MT0000913 368-162 8-10MM 0.001MM 368-102-10 MT0000914 368-163 10-12MM 0.001MM 368-103-10 MT0000915 368-164 12-16MM 0.005MM 368-104 MT0000916 368-165 16-20MM 0.005MM 368-105 MT0000917 368-166 20-25MM 0.005MM 368-106 MT0002066 268-167 25-30MM 0.005MM 368-107 MT0002982 368-168 30-40MM 0.005MM 368-138 MT0002197 368-169 40-50MM 0.005MM 368-139 MT0001931 368-170 50-63MM 0.005MM 368-140 MT0003112 368-171 62-75MM 0.005MM 368-141 MT0001744 468-163 10-12MM 0.001MM 468-133 MT0001745 468-164 12-16MM 0.001MM 468-134-10 MT0002941 468-165 16-20MM 0.001MM 468-135 MT0002942 468-166 20-25MM 0.001MM 468-136-10 Holtest Complete-unit Set Easy and accurate measurement of inside diameter Individual MT0000943 368-911 6-12MM 0.001MM 368-901 MT0000944 368-912 12-20MM 0.005MM 368-902 MT0000956 368-914 50-100MM 0.005MM 368-954 Holtest (Type II, Complete-Unit Set In Case) With Extension Rod MT0000958 368-991 12-20MM 0.005MM 368-972 MT0000957 368-992 20-50MM 0.005MM 368-963 MT0002099 368-992 50-100MM 0.005MM 368-964 Digimatic Holtest Set Complete Set Feature: IP 65 protection Included setting ring Able to connect with PC (spec) Interchangeable head MT0002760 468-973 20-50MM 0.001MM 468-953-10 Interchangeable-Head Set 16
DIAL INDICATOR Dial Indicator Lug-Back - Series 1 Features: Spindle is mad of hardened stainless steel Gears fit tight for dependable accuracy Face diameter: 41mm Shaft alignment measurement 1040S 1044S 1013S-10 MT0001897 1013S-10 1MM 0.002MM 1013F Lug-Back MT0001727 1040S 3.5MM 0.01MM 1040F Lug-Back MT0000373 1044S 5MM 0.01MM 1044F Lug-Back Back Plunger Dial Indicator 39.6 13.8 43.3 43.3 25 21.5 1160 1960 22 35 MT0001859 1960 1MM 0.01MM - MT0000375 1160 5MM 0.01MM 1158 Back Plunger Dial Indicator Lug-Back-Series 2 17.7 20 2109S-10 2110S-10 2050S 2046S 75.2 29.8 16.9 57 52 38.8 EDP No. Part No. Range Graduation Old Code Dial Reading MT0000389 2109S-10 1MM 0.001MM 2109F 0-100-0 MT0000391 2110S-10 1M 0.001MM 2110F 0-100(100-0) MT0000394 2113S-10 2MM 0.001MM 2113F 0-100-0 MT0000397 2119S-10 5MM 0.001MM 2119F 0-100-0 MT0000379 2046S 10MM 0.01MM 2046FE 0-100(100-0) MT0002136 2047S 10MM 0.01MM 2047FE 0-50-0 MT0000387 2050S 20MM 0.01MM 2050FE 0-100(100-0) MT0000388 2052S 30MM 0.01MM 2052FE 0-100(100-0) MT0004345 2046SB 10MM 0.01MM - 0-100 17
DIAL INDICATORS Dial Indicator - Series 3 14.1 75.5 25.9 61.2 3109S-10 3058S-19 Dial Indicator - Series 4 MT0002094 3109S-10 1MM 0.001MM 3109F MT0000408 3046S 10MM 0.01MM 3046F MT0002613 3050S 20MM 0.01MM 3050F Lug-Back MT0000412 3058S-19 50MM 0.01MM 3058F MT0002445 4046S 10MM 0.01MM 4046 Lug-Back Dial Test Indicator Pocket Type Horizontal Type Vertical Type Horizontal Type Basic Unit 513-501, L=12mm 513-517, L=20.9mm 513-515, L=44.5mm 513-444, L=20.9mm 513-454, L=20.9mm 513-401, L=12.8mm 513-405, L=14.7mm 513-414, L=36.8mm 513-404, L=20.9mm 513-415, L=44.5mm Full Set MT0000436 513-401E 0.14MM 0.001MM - Dial Test Indicator Basic-Unit Horizontal Type MT0000419 513-501T 0.14MM 0.001MM 513-101 Dial Test Indicator Full-Set Pocket Type MT0000439 513-405E 0.2MM 0.002MM 513-205 Dial Test Indicator Basic-Unit Horizontal Type MT0002106 513-405T 0.2MM 0.002MM 513-905F Dial Test Indicator Full-Set Horizontal Type MT0000440 513-414E 0.5MM 0.01MM 513-214E Dial Test Indicator Basic-Unit Horizontal Type MT0002107 513-414T 0.5MM 0.01MM 513-914F Dial Test Indicator Full-Set Horizontal Type MT0000423 513-404E 0.8MM 0.01MM 513-204E Dial Test Indicator Basic-Unit Horizontal Type MT0000438 513-404T 0.8MM 0.01MM 513-904F Dial Test Indicator Full-Set Horizontal Type MT0000422 513-517E 0.8MM 0.01MM 513-117-1 Dial Test Indicator Basic-Unit Pocket Set MT0000421 513-517T 0.8MM 0.01MM 513-117 Dial Test Indicator Full-Set Pocket Type MT0000450 513-454T 0.8MM 0.01MM - Dial Test Indicator Full-Set Vertical Type MT0000442 513-415E 1MM 0.01MM 513-215E Dial Test Indicator Basic-Unit Horizontal Type MT0000441 513-415T 1MM 0.01MM 513-925F Dial Test Indicator Full-Set Horizontal Type MT0002189 513-515T 1MM 0.01MM 513-115 Dial Test Indicator Full-Set Pocket Type MT0003996 513-426E 1.5MM 0.01MM - Dial Test Indicator Basic-Unit Horizontal Type MT0000446 513-444E 1.6MM 0.01MM - Dial Test Indicator Basic-Unit Horizontal Type 20 MT0000447 513-444T 1.6MM 0.01MM - Dial Test Indicator Full-Set Horizontal Type 20 18
DIGIMATIC INDICATORS IDS Digimatic Indicator Features: Battery life of 20,000 hours in continous use has been achieved Data output port to statistical process control systems ABS (absolute) sensor can restore last origin position MT0002007 543-781 12MM 0.01MM 543-681 Lug-Back With SPC MT0001993 543-781B 12MM 0.01MM 543-681B Flat-Back With SPC MT0000468 543-682B 12.7MM(0-5 ) 0.01MM - IDF Digimatic Indicator Features: The external power supply GO/NG justment result is out tolerance The maximum, minimum or runout can be displayed during measurement Analog bar indcator has been intergrated MT0002527 543-554E 50.8MM(2 ) 0.001MM 543-525E With Back-Lit LCD Screen IDC Digimatic Indicator Features: Max/min and run out valve 330º rotary display Function lock, to prevent preset function MT0002656 543-400 12MM 0.01MM 543-270 Lug-Back MT0002773 543-390B 12MM 0.001MM 543-250B Flat-Back MT0002126 543-391 0.5 /12.7M 0.001MM 543-251 Lug-Back MT0002722 543-470B 25MM 0.001M 543-450B Flat-Back 19
BORE GAGE Bore Gage with Standard Dial Indicator Bore Gage for Small Hole Bore Gage for Blind Holes Bore Gage for Xtra Small Hole Bore Gage - Short Leg Type Inside measurement Bore Gage with Standard Dial Indicator MT0000239 511-711 18-35MM 0.01MM 511-171 MT0000235 511-721 18-35MM 0.001MM 511-167 MT0000240 511-712 35-60MM 0.01MM 511-172 MT0000236 511-722 35-60MM 0.001MM 511-168 MT0000238 511-723 50-150MM 0.001MM 511-170 MT0000242 511-713 50-150MM 0.01MM 511-174 MT0000243 511-714 100-160MM 0.01MM 511-175 MT0000244 511-715 160-250MM 0.01MM 511-176 Bore Gage for Small Hole MT0000250 511-203 10-18.5MM 0.001MM - MT0000251 511-204 10-1835MM 0.01MM - Bore Gage for Blind Holes MT0000260 511-411 15-35MM 0.01MM - With Standard Dial Indicator For Small Hole For Blind Hole MT0000261 511-412 36-60MM 0.01MM - Bore Gage for Extra Small Hole MT0000295 526-127 10-18MM 0.01MM - For Xtra Small Hole Bore Gage with Standard Dial Indicator MT0002153 511-766 18-35MM 0.01MM 511-461 MT0002436 511-771 18-35MM 0.001MM 511-471 MT0002910 511-767 35-60MM 0.01MM 511-462 MT0000262 511-772 35-60MM 0.001MM 511-472 MT0002909 511-768 50-150MM 0.01MM 511-464 Short Leg Type 20
THICKNESS GAGE Digimatic Thickness Gage 547-321 547-301 547-401 MT0000357 547-301 0-10MM 0.01MM - Type A (Standard Type) MT0002617 547-321 0-10MM 0.01MM - Type B (Deep Throat Type) MT0001775 547-401 0-12MM 0.001MM - For Paper, Film, Wire Dial Thickness Gage 7321 7301 MT0002937 7327 0-1MM 0.001MM - Type A (Standard Type) MT0000359 7301 0-10MM 0.01MM - Type A (Standard Type) MT0000365 7321 0-10MM 0.01MM - Type B (Deep Throat Type) Dial Thickness Gage-Pocket 7331S Measure paper thickness easily MT0000362 7331S 0-10MM 0.01MM - Pocket Type 21
STAND Dial Gage Stand 7002 (Flat Anvil) 7001 (Serrated Anvil) 519-109M (Transfer Stand) 215-151-10 (Granite Comparator Stand) EDP No. Part No. Description Stem Old Code Remaks MT0000564 7001-10 Working Height 100MM ф8mm 7001 With Serrated Anvil MT0000565 7002-10 Working Height ф8mm 7002 With Flat Anvil MT0000563 519-109-10 Working Height 300MM ф8mm 519-109M With Serrated Anvil MT0000561 215-151-10 150 x 200 x 50MM (H:260MM) ф8mm 215-151 With Fine Adjustment Magnetic Stand 7010S-10 7011S-10 7032 7014 7012-10 7033B EDP No. Part No. Range Old Code Remaks MT0000566 7010S-10 ф8mm,ф4.5mm,ф3/8 7010SN - MT0000567 7011S-10 ф8mm,ф4.5mm,ф3/8 7011SN With Fine Adjustment MT0000568 7012-10 ф8mm,ф6mm,ф3/8 7012 For Dial Test Indicator MT0000569 7014 ф8mm,ф6mm,ф3/8 - With On-Off Switch MT0000570 7033B ф8mm,ф3/8 7019B Mechanical Lock Type MT0002934 7032 ф8mm 7027-10 Mechanical Lock Type Micrometer Stand 156-102 156-101 156-105 EDP No. Part No. Range Remarks MT0000559 156-101-10 Up To 100MM (4 ) Adjustable Angle Type MT0001768 156-102 Up To 300MM (12 ) Vertical Type MT0000560 156-105-10 0-25MM(0-1 ), 25-50MM(1-2 ) Fixed Angle Type 22
CALIBRATION TOOLS Setting Rings EDP No. Part No. Range Remaks MT0001054 177-125 8MM/±1.5µM MT0001055 177-126 10MM/ ±1.5µM MT0001713 177-284 12MM/ ±1.5µM MT0002983 177-177 16MM/ ±1.5µM MT0001061 177-286 20MM/ ±1.5µM MT0001057 177-139 25MM/ ±1.5µM MT0002481 177-288 30MM/ ±1.5µM MT0001058 177-140 35MM/ ±1.5µM MT0001715 177-290 40MM/ ±1.5µM MT0002420 177-146 50MM/ ±1.5µM MT0002634 177-314 62MM/ ±1.5µM MT0005083 177-302 175MM/ ±1.5µM Optical Paralel Set Use for calibrate your measuring devices Steel Setting Ring Design to inspect parallelism and flatness of measuring faces of micrometers EDP No. Part No. Range Remaks MT0000818 157-903 0-25MM 12, 12.12, 12.25, 12.35MM Caliper Checker EDP No. Part No. Range Remaks MT0000269 515-555 300MM Length to Check: 20, 50, 100, 150, 200, 250, 300MM MT0000270 515-556-2 600MM Length to Check: 20, 50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600, MM ( ) Length for checking accuracy of inside measurement Gauge Block Set Checking the accuracy of a caliper Also can used for setting a height gauge EDP No. Part No. Range Remaks MT0000273 516-101-10 1MM-25MM Gauge Block Set Steel (10)#1 MT0002109 516-106-10 2.5MM-25MM Gauge Block Set Steel (10)#0 MT0000275 516-111-10 1MM-50MM Gauge Block Set Steel (16)#0 MT0000285 516-938-10 1.0005MM-100MM Gauge Block Set Steel (112)#0 MT0005446 516-942-10 1.0005MM-100MM Gauge Block Set Steel (103)#0 MT0000292 516-962-10 1.005MM-100MM Gauge Block Set Steel (47)#0 MT0000293 516-966-10 1.005MM-60MM Gauge Block Set Steel (32)#0 MT0002822 516-996-10 1.001MM-100MM Gauge Block Set Steel (46)#1 MT0006325 516-101Z-10 1MM-25MM Gauge Block Set Steel (10)#1 MT0006326 516-106Z-10 2.5MM-25MM Gauge Block Set Steel (10)#0 MT0006327 516-938Z-10 1.0005MM-100MM Gauge Block Set Steel (112)#0 MT0006329 516-962Z-10 1.005MM-100MM Gauge Block Set Steel (47)#0 Steel 112-Block Set Optical Parallel Optical Parallel, Grinding Stone 23
CALIBRATION TOOLS Dial Gage Tester MT0001284 170-102-10 0-25MM 0.001MM 170-102M-2 UDT-2 Dial Gage Tester MT0001521 12AAK84 - - 951498 Stand for Dial Bore Gage * Not including dial indicators/bore gage Calibration Tester Dial Indicator Calibration Bore Gage Calibration * Not including dial test indicator Dial Test Calibration EDP No. Part No. Range Graduation Remaks MT0001310 521-103 0-1MM 0.0002MM Calibration Tester Black Granite Surface Plate * Not including stand EDP No. Part No. Flatness Grade Remaks MT0003215 517-101C 0.005MM 1 300 x 300 x 100MM MT0000985 517-111C 0.006MM 1 450 x 300 x 100MM MT0000986 517-114C 0.008MM 1 600 x 450 x 100MM MT0000380 517-103C 0.008MM 1 600 x 600 x 130MM MT0003486 517-303C 0.005MM 1 600 x 600 x 130MM MT0000982 517-105C 0.009MM 1 750 x 500 x 130MM MT0000983 517-107C 0.012MM 1 1000 x 750 x 150MM MT0000984 517-109C 0.013MM 1 1000 x 1000 x 150MM 24
MISCELLANEOUS Precision Square 916-213 916-404 916-102 Steel Rules - Wide Ridgid Steel Rules - Full Flexible Rules Combination Square set EDP No. Part No. Range Remaks MT0000541 916-102 100MM x 70MM Beveled-edge Type MT0000546 916-213 100MM x 70MM Precision Square MT0000542 916-103 150MM x 100MM Beveled-edge Type MT0000547 916-214 150MM x 100MM Precision Square MT0000555 916-404 200MM x 130MM Precision Square With Stand EDP No. Part No. Range Graduation Remaks MT0000997 182-105 6 /150MM 1/32,1/64,1MM,0.5MM MT0000999 182-111 150MM 1MM, 0.5MM MT0001000 182-121 12 1/8,1/16,1/32,1/64 MT0001002 182-131 300MM 1MM, 0.5MM MT0001004 182-165 24,600MM 1/32,1/64,1MM,0.5MM Wide Rigid Rule EDP No. Part No. Range Graduation Remaks MT0001006 182-205 6 /150MM 1/32,1/64,1MM,0.5MM Full Flexible Rule MT0001923 182-302 6 /150MM 1/16,1/32,1/64,1MM,0.5MM Semi Flexible Rule MT0001007 182-225 12 /300MM 1/32,1/64,1MM,0.5MM Full Flexible Rule MT0001009 182-309 40 /1000MM 1/16,1/32,1/64,1MM,0.5MM Semi Flexible Rule Square head: Used to set the rule at 90 degrees or 45 degrees to an edge of a workpiece Center head: Used to locate centers of round workpiece Protractor head: Used to set the rule at a desired angle to an edge of a workpiece. Also used for measuring angles Universal Bevel Protractor EDP No. Part No. Range Graduation Remaks 10006096 180-907B 12 /300MM 1/32,1/64,1MM,0.5MM With Blade MT0001016 180-910U 300MM 1MM,0.5MM Precision Level EDP No. Part No. Range Graduation Remaks MT0001020 187-901 150MM, 300M 5min. (0-90 -0 ) With 60, 45, 30 Edges MT0001021 187-907 150MM 5min. (0-90 -0 ) With 60, 45 Edges V-Block 960-606 960-706 MT0001933 960-603 200MM x 44MM x 38.2MM 960-606 - - MT0002274 960-703 200MM x 44MM x 200MM 960-706 181-902-10 181-947 EDP No. Part No. Range Remaks MT0000221 181-902-10 25MM With Clamp MT0001836 181-947 50MM Magnetic Type 25
MISCELLANEOUS Radius Gauge 186-105 186-110 Screw Pitch Gage Thickness Gage EDP No. Part No. Range Remaks MT0004379 186-110 0.4MM-6MM (18Pairs) MT0000508 186-902 0.5MM-13MM (26 Pairs) MT0000502 186-105 1MM-7MM (34 Pairs) MT0000503 186-106 7.5MM-15MM (32 Pairs) MT0000504 186-107 15.5MM-25MM (30 Pairs) 90 Arc 180 Arc EDP No. Part No. Range Remaks MT0000475 188-101 4TPI-42TPI (30 Leaves) MT0000476 188-102 4TPI-60TPI (28 Leaves) Withworth MT0000477 188-111 4TPI-42TPI (30 Leaves) unified MT0000481 188-151 4TPI-42TPI, 0.4MM-7MM Metric & Unified MT0000480 188-130 0.35MM-6MM (22 Leaves) MT0000478 188-121 0.4MM-7MM (18 Leaves) Metric MT0000479 188-122 0.4MM-7MM (21 Leaves) Reticles for Pocket Comparator EDP No. Part No. Range Old Remaks MT0000491 184-302S 0.03MM-0.5MM (13 Leaves) 184-302 MT0000490 184-301S 0.05MM-1MM (13 Leaves) 184-301 MT0000492 184-303S 0.05MM-1MM (28 Leaves) 184-303 MT0000493 184-304S 0.05MM-1MM (20 Leaves) 184-304 MT0000496 184-307S 0.03MM-0.5MM (13 Leaves) 184-307 MT0000492 184-303S 0.05MM-1MM (28 Leaves) - MT0002127 184-308S 0.05MM-0.8MM (10 Leaves) - Clear Loupe Long Leaf Type EDP No. Part No. Range MT0000520 183-102 MT0002369 183-104 MT0001790 183-109 Zoom Loupe Reticle EDP No. Part No. Range Remarks MT0000530 183-302 10X Magnification Drawtube Removable MT0000531 183-303 15X Magnification Pocket Comparator EDP No. Part No. Range Remarks MT0002786 183-304 8X-16X(Zoom) Magnification With Reticle Zoom Loupe * Scale Graduation 0.1MM,0.005 EDP No. Part No. Range Remarks MT0000519 183-101 8X Magnification Optional Reticle MT0000525 183-131 10X Magnification Available MT0001540 950757 - Optional Illuminator Spring Caliper EDP No. Part No. Range Remarks MT0000526 183-210 25X Magnification Pen Type MT0000528 183-203 50X Magnification With Stand EDP No. Part No. Range Remarks MT0000076 950-223 8 /200MM Outside Spring Caliper MT0000009 950-233 8 /200MM Inside Spring Caliper 26
SURFTEST Surftest SJ-210 Model Code No. Order No. Evaluation Length Measuring Range Measuring Force Drive/Detector Unit Evalution Parameter Roughness Standard Cutoff Length Display Data Output Dimension SJ-210 178-561-02E MT0002378 17.5mm 360µm (-200µM to + 160µM) 4mN Detecting method: Skidded Material of Stylus: Diamond Stylus tip Radius: 5µm Ra,Rc,RY,RZ,Rq,Rt,Tmax,Rp,Rv,R3z,Rsk,Rku,Rc,Rpc,Rsm,R z1max,s,hsc,rzjis,rppi, R a,r q,rlr,rmr, Rmr(c),R C,R k,rpk,rvk,mr1,mr2,a1,a2, Vo, Rpm,Tp,Htp,R,Rx,Ar JIS 82, JIS 94, JIS 01, ISO 97,ANSI, VDA λc:0.08, 0.25, 0.8, 0.25mm λs: 2.5, 8µM LCD Via RS232C Interface/SPC output, USB Digimatic Output 115 x 65.8 x 160mm Surftest SJ-310 Model Code No. Order No. Evaluation Length Measuring Range Measuring Force Drive/Detector Unit Evalution Parameter Roughness Standard Cutoff Length Display SJ-310 178-571-02E MT0001807 17.5mm 360µm (-200µM to + 160µM) 0.75mN or 4mN Detecting method: Skidded Material of Stylus: Diamond Stylus tip Radius: 5µm Ra,Rc,RY,RZ,Rq,Rt,Tmax,Rp,Rv,R3z,Rsk,Rku,Rc,Rpc,Rsm,R z1max,s,hsc,rzjis,rppi, R a,r q,rlr,rmr, Rmr(c),R C,Rk,Rpk,Rvk,Mr1,Mr2,A1,A2,Vo,Rpm,Tp,Htp,R,Rx,Ar JIS 82, JIS 94, JIS 01, ISO 97,ANSI, VDA λc:0.08, 0.25, 0.8, 0.25mm λs: 2.5, 8µM LCD (touch Panel Data Output Dimension Via RS232C Interface/SPC output, USB Digimatic Output 275 x 109 x 198mm 27
D PROFILE PROJECTOR PH-3515F PJ-A3000 PH-3515F Model PH-3515F Order No. 172-858 XY stage travel range 254 x 152 mm Measurement method Linear encoder Quick-release mechanism X axis XY stage table top size 450 x 146 mm Swiveling function ± 10 Max. stage loading 45 kg Remarks - PJ-A3010-100 Magnification 10X 20X 50X 100X View field ø31.5 ø15.7 ø6.3 ø3.1 W 66 (20) 32.5 (2) 12.6 5-50 models 123.5 123.5 123.5 123.5 H - 100 models 91 91 91 91-150 models 103.5 103.5 103.5 103.5-200 models 92.5 92.5 92.5 92.5-50 models 224 (198) 87 (61) 27 10-100 models 182 87 (61) 27 10-150 models 207 (198) 87 (61) 27 10-200 models 185 87 (61) 27 10 Technical Data : Projected image : Erect Protractor scren (optional) Effective diameter : 353 (13.9")mm 356 (14")** Screen material : Fine-ground glass Screen rotation : ±360, fine feed and clamp Angle reading : Digital counter (LED) Resolution:1' or 0.01 (switchable) Range: ±370 ABS/INC mode switching, Zero Set Reference line : Cross-hairs Projection lens : 10x [172-184] Optional: 5x, 20x, 50x, 100x Magnification accuracy Contour illumination : ±0.1% or better Surface illumintaion : ±0.15% or better Maximum workpiece height : Refer to the projection capacity (H) below. Contour illumination Light source : Halogen bulb (24V, 150W) Optical system : Telecentric system Function : 2-step (high/low) brightness switch, Heat-absorbing filter, Cooling fan Surface illumination Light source : Halogen bulb (24V, 200W) Optical system : Vertical illumination Functions : Adjustable condenser lens, Vertical/ oblique surface illumination selectable Heatabsorbing filter, Cooling fan Focusing : Manual focus Resolution : 0.001mm or 0.0001"/0.001mm (using optional KA counter) Power supply : 100-240V AC, 50/60Hz Mass : 150 kg PH-3515F Unit: mm Magnification 5X 10X 20X 50X 100X View field 70.6 35.5 17.65 7.06 3.5 W 175 235 235 80 109 H 160(64) 93(35) 40 14.6 9.5 D 152.4 152.4 116 30.4 19 Technical Data : Projected image : Inverted Protractor screen Effective diameter : 315 mm (12.4") Screen material : Fine-ground glass Screen rotation : ± 360, fine feed and clamp Angle reading : Digital counter (LED) Resolution: 1' or 0.01 (switchable) Range: ±370 ABS/INC mode switching, Zero Set Projection lens : 10x (172-202) Optional: 20x, 50x, 100x Magnification accuracy Contour illumination : ±0.1% or better Surface illumintaion Maximum workpiece height : ±0.15% or better : Refer to the projection capacity (H) below Contour illumination Light source : Halogen bulb (24V, 150W) Optical system : Telecentric system Functions : 2-step (high/low) brightness switch, Heat-absorbing filter, Cooling fan Surface illumination Light source : Halogen bulb (24V, 150W) Optical system : Vertical illumination with adjustable condenser lens Functions : Heat-absorbing filter, Cooling fan Resolution : 0.001mm or 0.0001"/0.001mm (.00005"/0.001mm: digital head) Power supply : 100-240V AC, 50/60Hz Mass : 105kg - 140kg Model PJ-A3010F-100 PJ-A3005F-150 PJ-A3010F-200 Order No. (metric) 702-703 302-702 302-701 Order No. (inch/metric) 302-713 302-712 302-711 XY stage travel range 100 x 100 mm 150 x 150 mm 200 x 100 mm Measurement method Linear encoder Linear encoder Linear encoder Quick-release mechanism X and Y axes X and Y axes X and Y axes XY stage table top size 250 x 250 mm 280 x 152 mm 380 x 250 mm XY stage effective area 142 x 142 mm 185 x 84 mm 266 x 170 mm Stage glass No. 12BAE041 381349 382762 Sweveling function - - ± 3 Max. stage loading 10 kg 8 kg 8 kg Remarks - - - 28
SURFACE ROUGHNESS TESTER CV-2100M4 (PC type) CV-2100M4 (PC type) Model No. CV-2100M4 Order No.* 218-643A Measurement range X- axis 4 (100mm) Z1-Axis (Detector unit) 2 (50mm) Z2-axis (column) travel range 13.8 (350mm) X-axis inclination angle ±45º Resolution X-axis 3.93µin (0.1µm) Z1-axis 3.93µin (0.1µm) Driver method X-axis Motorized drive 0-0.79in/s (0-20mm/s) Z2-axis (column) Manual (quick-up-and-down motion, fine feed) Measuring Speed 0.00078-0.2in/sec (0.02-5mm/s) Linearity accuracy (X-axis horizontal orientation) 98.4µin/4in (2.5µm/100mm) Accuracy (20ºC) X-axis ±(100+20L)µin [±(2.5+0.02L)µm)] L= measurement Length (mm) Z1-axis ±(100+20L) µin [(2.5+ 0.1H ) µm)] H= Measurement height from horizontal position within 1 (±25mm) Measurement direction Push and pull Measurement surface direction Downward Measuring Force (3gf) (30±10mN) Stylus traceable angle (Standard accessory stylus) Ascent77º, Descent 87º (Depends on the surface condotion) External dimensions (W x D x H) 745 x 450 x 885 mm Mass 145.8 kg CV-C3200S4 CV-C3200S4 with personal computer system and software Technical Data : X1 axis Stylus orientation : Upward/ downward Measuring range : 100 mm or 200 mm Measuring force : 30 mn Resolution : 0.05 µm Traceable angle : Ascent: 77, descent: 83 Scale : Linear encoder Stylus tip : Radius: 25 µm, carbide tip Drive speed : 0-80 mm/s and manual Base size (W x H) : 600 x 450 mm or 1000 x 450 mm Measuring speed : 0.02-5m/s Base material : Granite Measuring direction : Forward/backward Mass Traverse linearity : 0.8 µm/ 100 mm, 2 µm/ 200mm Main unit : 140 kg Accuracy (at 20 C) : ±(0.8+0.01L) µm Controller unit : 14 kg ±(0.8+0.02L) µm Remote control box : 0.9 kg Inclining range : ±45 Power supply : 100-120 V AC ±10% Z2 axis (column) 200-240 V AC ±10%, 50/60 Hz Vertical travel : 300 mm or 500 mm Power consumption : 400 W (main unit only) Resolution : 1 µm Scale : ABSOLUTE linear encoder Model No. CV-3200S4 Drive speed : 0-30 mm/s and manual mm 218-481* Z1 axis (detector unit) Order No. inch 218-491* Measuring range : ± 30 mm X1-axis measuring range 100 mm Resolution : 0.04 µm Vertical travel 300 mm power column Scale type : Rotary arc encoder Granite base size (WxD) 600 x 450 mm Accuracy (at 20 C) : ±(1.6+I2HI/100) µm Dimenasion (main unit, WxDxH) 756 x 482 x 966 mm Stylus movement : Arc Mass (main unit) 140 kg 29
MICROSCOPES TM-500 Unit : mm TM-510 Angle reading Technical Data : Observation Optical tube : Erect image : Monocular (diopter adjustable) Despression angle: 30 Reticle: 90 broken cross-hair (176-126) Angel reading : Range 360 Minimum reading: 6' (by vernier) Eyepiece : 15X (176-116), view field dia. : 13mm Optional: 10X, 10X Objective : 2X (176-138), Working distance: 67 mm Optional: 5X, 10X Total magnification : 30X Transmitted illumination Light source : Tungsten bulb (24 V, 2 W) Functions : Light intensity adjustable, Nonstepped brightness adjustment Surface illumination Light source : Tungsten bulb (12 V, 150 W) Functions : Light intensity adjustable Power supply : 100/110/120/220/240 V AC, 50/60 Hz Mass : 13.5 g (14.5kg: TM-510) Model No. TM-505 TM-510 Order No. 176-811 176-812 XY stage travel range 50 x 50 mm 100 x 50 mm Measurement method Micrometer head (optional) Micrometer head (optional) Floating function - - XY stage table top size 152 x 152 mm 240 x 152 mm Effective area of table 96 x 96 mm 154 x 96 mm Max. workpiece height 115 mm 107 mm Max. stage loading 5 kg 5 kg Remarks - - 30
HARDNESS TESTING MACHINES ROCKWELL HARDNESS TESTING MACHINES HR-210 MR/ 430MS ROCKWELL TYPE HARDNESS HR-522 HR-210MR HR-430MS Model No. HR-210MR HR-430MS Order No. 963-220 963-241 Type of hardness test Rockwell - Rockwell superficial Standard JIS B 7726 ISO6508-2 (ASTM E18) Display Analog Minimum reading 0.5HR graduation 0.1HR indication Preliminary test force (Handling support) Preliminary test force setting Automatic pre-setting dial gauge Automatic steering wheel brake - Dial switching Total test force setting Weight change Dial switching Total test force control Motor drive - Button start Motor drive-automatic start Test force duration Fixed 3-5.5s or manual 3-60s setting or manual operation Maximum specimen height 180 mm (100mm if cover is attached) Maximum specimen depth 165 mm (from indenter axis to the frame) - Success at failure decision function Function - Offset revision function - Hardness conversion function Data output - Digimatic (SPC), RS-232C Power supply AC100-240V, 1.2A Dimension (W x D x H) Approximately 235 x 512 x 780 mm Approximately 235 x 516 x 780 mm Mass Approximately 47 kg Approximately 50 kg HR-522 Touch-screen type: Touch screen operation with a back-lit LCD graphic display Remote selection of the test force linked to the hardness scale selection Choice of message language in English, German, French, Spanish, Italian and Japanese for user friendly operation Cylindrical and spherical surface compensation Data offset Conversion to other hardness scales Powerful statistical processing with flexible data point editing and 1024 data memory Measured data editing OK/±NG tolerance judgment Statistical processing, histogram and X-R chart Technical Data : Preliminary test force : 29.42N, 98.07N Test force Rockwell superficial : 147.1, 294.2, 441.3N Rockwell : 588.4, 980.7, 1471N Brinell : 61.29, 98.07, 153.2, 245.2, 294.2, 306.5, 612.9, 980.7, 1226, 1839N Test force setting : By control unit Load control : Automatic (load, dwell, unload) Load dwell time : 0s-120s (1s increments) Max. specimen height : 205 mm (for standard flat anvil) max. specimen depth : 150 mm (from the center of indenter shaft) Stage elevation : Manual or power drive Control unit : Sheet-switch type or touch-screen type Data output : RS-232C, Digimatic code (SPC) and centronics Power supply : 100/120/220/240V AC, 50/60Hz Dimension (WxDxH) Main unit : 250 x 670 x 605 mm Control unit : 165 x 260 x 105 mm Mass (main unit) : 65 kg Model No. HR-522 Order No. 810-203 Preliminary test force 29.42N, 98.07N Rockwell superficial : 147.1, 294.2, 441.3N Test force Rockwell : 588.4, 980.7, 147N Brinell : 61.29, 98.07, 153.2, 245.2, 194.2, 306.5, 612.9, 980.7, 1226, 1839N Test force setting By control unit Stage elevation Manual Control unit 31
INPUT & OUTPUT TOOLS Digimatic gage/pc Data Input Device EDP No. Part No. Remarks MT0003844 264-012-10 Digimatic USB Signal Specification: Code No 264-012-10 Data 1nput port 1 channel for Mitutoyo digimatic gage Data output port Digimatic USB Power supply Supplied from PC Dimension 72(W) x 43(D) x 23.5(H) mm Mass 74 gram Digimatic Mini Processors (DP1-VR) 05CZA663 EDP No. Part No. Remarks MT0003887 05CZA663 SPC Cable for Micrometer 293 Type * Not including SPC cable EDP No. Part No. Old Remarks MT0000160 264-504-5E 364-504E Digimatic Data Mini Processor DP1VR, 240/230VAC SPC Connection Cables 936937 937387 905338 905689 EASILY TO CONNECT YOUR MEASURING DEVICES TO PC GENERATE YOUR REPORTING SHEET PLEASE CONTACT US FOR FUTHER INFORMATION Code No 936937 937387 905338 905689 959149 05CZA662 Application IDF Dig. Indicator Series 543 surftest SJ-201 Series 178 surftest SJ-301 Series 178 Digimatic Micrometers Series 193, 314, 317, 323, 324, 326, 331, 340, 342, 343, 369, 389, 395, 406, 422 Digimatic Bench Micrometers Series 121 Digimatic Inside Micrometer Series 345 Digimatic Series 468 IDS Digimatic Indicators Series 543 IDC Digimatic Indicators Series 543 Digimatic Caliper Series 550, 551 Digimatic Thickness gages Series 547 Digimatic Height Gage Series 192,570 Digimatic Depth Gage Series 547 Digimatic Caliper Series 500, 550, 551, 573 Digimatic Depth Gage Series 571 Digimatic Scale Unit Series 572 Digimatic Micrometers Series 293, 314, 323, 324, 326, 331, 342, 343, 369, 389, 395, 406, 422 32
USB INPUT TOOL DIRECT USB type input tool with slim body. The inclusion of dedicated optional software enables a level of measurement convenience unrealized until now. 33
MEASUREMENT DATA WIRELESS COMMUNICATION SYSTEM U-WAVE 34
35
kls/p&a.166/5kmeasuring.22/can.gra/05.14 36