GX620 (MS-1651)Disassemble SOP 1 Battery Pack 2 BOTTOM DOOR ASSY 3 THERMAL-KIT And CPU Module 4 RAM WLAN And TUNER Module 5 HDD Module ASSY 6 ODD Module ASSY 7 HINGE COVER ASSY 8 UP CASE ASSY 9 LOWER CASE ASSY 10 LCD MODULE ASSY
1 Battery Pack 1-1:Push the battery Unlock button as below; 1-2:Push the battery Release button as below, then slide the battery pack out of the slot; 1 Battery Pack S9N-0366200-SB3 1
2 BOTTOM DOOR ASSY 2-1:Remove 2pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm GX620&MS-1651 Disassemble SOP 2-2:Remove Bottom Door Assy as below;
2-3:Remove SIM Card Door as below; 1 Screw E43-1255001-H29 2 2 SIM CARD DOOR E2P-6510511-Y31 1 2 BOTTOM DOOR ASSY 307-651J411-Y31 1
3 THERMAL-KIT And CPU Module 3-1:Remove 7pcs SPING Screws, Then Disconnect CPU Fan sink Cable; Note:Screw driver torque is 2.0~2.5kgf.cm 5 6 2 4 7 3 1 3-2:Remove CPU Fan sink; 1 CPU FANSINK E32-0900531-F05 1
3-3: Open CPU slot as below; 3-4:Remove CPU Module; 1 CPU Module A09-2520106-I06 1
3-5:Remove 2pcs M2.5*5mm Screws; Note:Screw driver torque is 2.5~3.0kgf.cm GX620&MS-1651 Disassemble SOP 3-6:Remove VGA Card Module; 1 VGA CARD Module 602-V114-06S 1 2 Screw E43-1255001-H29 2
4 RAM WLAN And TUNER Module 4-1:Push RAM Slot Fastener as below; 4-2:Remove RAM Module; 1 RAM Module S7C-S347701-T10 2
4-3:Remove WLAN Card Antenna, Then remove 1pcs M2*3mm Screw; Note:Screw driver torque is 1.8~2.2kgf.cm 4-4:Remove WLAN Card Module; 1 WLAN CARD Module S57-0800180-I06 1 2 Screw E43-1203003-H29 1
4-5:Remove Tuner Antenna, Then remove 1pcs M2*3mm Screw; Note:Screw driver torque is 1.8~2.2kgf.cm 4-6:Remove Tuner Module; 1 TUNER Module S36-0000610-K45 1 2 Screw E43-1203003-H29 1
5 HDD Module ASSY 5-1:Remove 2pcs M2.5*5mm Screws Then remove HDD Door Assy as below; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E43-1255001-H29 2 2 HDD DOOR ASSY 307-651K411-Y31 1
5-2:Remove HDD Module as below; 1 Screw E43-1255001-H29 1
5-3:Remove 2pcs M3*3.5mm Screws Then remove HDD Bracket as below; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E43-1303501-H29 2 2 HDD Bracket 307-6510111-Y28 1 3 HDD MODULE ASSY S71-2425504-F06 1
6 ODD Module ASSY 6-1:Remove 1pcs M2.5*5mm Screw Then remove ODD Module Assy as below; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E43-1255001-H29 1
6-2:Remove ODD Bezel as below; 1 ODD Bezel E2P-651F211-Y31 1
6-3:Remove 2pcs M2*3mm Screws Then remove ODD Bracket as below; Note:Screw driver torque is 1.5~1.8kgf.cm 1 Screw E43-1203007-H29 2 2 ODD Bracket E2M-6510211-Y28 1
7 HINGE COVER ASSY 7-1:Push Fastener as below; GX620&MS-1651 Disassemble SOP
7-2:Remove Hinge Cover as below; GX620&MS-1651 Disassemble SOP 1 HINGE COVER 307-651E111-Y31 1
7-3:Remove Hinge Cover Cable as below; 1 POWER BOARD 607-1651B-C10 1
7-4:Remove Cap Sensor Board as below; 1 Cap Sensor Board 607-1651D-C10 1
7-5:Remove Cap Sensor Board as below; 1 Cap Sensor Board 607-1651D-C10 1 2 Cap Sensor Board Cable K1C-1012023-J36 1
8 UPCASE ASSY 8-1:Remove 5pcs M2*3mm Screws, Then remove Keyboard as below; Note:Screw driver torque is 1.5~2.0kgf.cm 1 Screw E43-1203003-H29 5 2 Keyboard S1N-3UTC131-C54 1
8-2:Remove 2pcs M2*3mm Screws, Then remove Power Board as below; Note:Screw driver torque is 1.5~2.0kgf.cm 1 Screw E43-1203003-H29 2 2 Power Board 607-1651B-C10 1
8-3:Remove 13pcs M2.5*5mm Screws, Then remove 2pcs M2.5*7mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E43-1255001-H29 13 2 Screw E43-1257001-H29 2
8-4:Remove PCI-E Card And XD Card as below; 1 PCI-E Card E2P-6510411-Y31 1 2 XD Card E2P-6510611-Y31 1
8-5:Disconnect Speaker Cable and Microphone Cable as below; 1 Speaker Cable S33-A020200-F33 1 2 Microphone Cable S34-2100580-F33 1
8-6:Remove FFC Cable(TO Audio Board) and FFC Cable(TO M/B) as below; 1 FFC Cable(TO Audio Board) K1C-1020003-J36 1 2 FFC Cable(TO M/B) K1C-1012024-J36 1
8-7:Remove 2pcs M2*3mm Screws, Then remove FFC Cable(TO M/B)&(TO Button) as below; Note:Screw driver torque is 1.5~2.0kgf.cm 8-8:Remove Touchpad Bracket; 1 Screw E43-1203003-H29 2 2 FFC Cable(TO Button) K1C-1012025-J36 1 3 Touchpad Bracket E2M-6510911-Y28 1
8-9:Remove 1pcs M2*3mm Screw, Then remove Touchpad Button Board; Note:Screw driver torque is 1.0~1.5kgf.cm 1 Screw E43-1203003-H29 1 2 Touchpad Button Board 607-1651C-C10 1
8-10:Remove FFC Cable (TO Button) as below; 1 FFC Cable(TO Button) K1C-1012025-J36 1 2 Touchpad Module S78-3700360-SD2 1
9 LOWER CASE ASSY 9-1:Remove 1pcs M2.5*5mm Screw, Then remove FFC Cable (TO Audio Board) as below; Note:Screw driver torque is 2.3±0.2kgf.cm 9-2:Remove FFC Cable (TO Power Board) as below; 1 Screw E43-1255001-H29 1 2 FFC Cable(To Audio Board) K1C-1020003-J36 1 3 FFC Cable(To Power Board) K1C-1018003-J36 1
9-3:Remove RJ11 Cable and Bluetooth Cable as below; 9-4:Remove M/B; 1 RJ11 CABLE K10-3002110-H58 1 2 BLUETOOTH CABLE K10-3008077-H39 1 3 M/B 607-16511-B10 1
9-5:Remove 1pcs M2*3mm Screw, Then remove Bluetooth Antenna; Note:Screw driver torque is 1.0~1.5kgf.cm 1 Screw E43-1203003-H29 1 2 BLUETOOTH ANTENNA S79-1800890-V03 1 3 BLUETOOTH MODULE 605-6837D-070 1
9-6:Remove 2pcs M2*3mm Screws, Then remove Audio Board; Note:Screw driver torque is 1.0~1.5kgf.cm 1 Screw E43-1203003-H29 2 2 AUDIO BOARD 607-1651A-C10 1 3 LOWER CASE ASSY 307-651D411-Y31 1
9-7:Remove Bluetooth Antenna RJ11 Cable and TV IO Jack; 1 BLUETOOTH ANTENNA S79-1800890-V03 1 2 RJ11 CABLE K10-3002110-H58 1 3 TV IO JACK K19-3001017-H39 1
10 LCD MODULE ASSY 10-1:Disconnect Camera Cable as below; GX620&MS-1651 Disassemble SOP 1 Camera Cable K10-3006056-H39 1
10-2:Remove 2pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm 10-3:Use Plastic Stick Push Hinge Cap as below; 1 Screw E43-1255001-H29 2 2 Hinge Cap_L E2P-6511311-Y31 1 3 Hinge Cap_R E2P-6511411-Y31 1
10-4:Draw Out Camera Cable Wireless Antenna and 3G Antenna as below; 1 3G Antenna S79-1800780-V03 1 2 Wireless Antenna_L S79-1800800-V03 1 3 Wireless Antenna_R S79-1800790-V03 1
10-5:Disconnect Coaxia Cable as below; 1 Coaxia Cable K19-3040006-H39 1
10-6:Remove 2pcs M2.5*7mm Screws; Note:Screw driver torque is 3.5±0.2kgf.cm 1 Screw E43-1257001-H29 2
10-7:Remove 8pcs LCD Rubbers Then remove 8pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm 1 LCD Rubber E2Y-6510111-Y40 8 2 Screw E43-1255001-H29 8
10-8:Remove LCD Bezel as below; 1 LCD BEZEL 307-651B411-Y31 1
10-9:Remove 6pcs M2.5*5mm Screws, Then remove Left And Right Hinge; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E43-1255001-H29 6 2 Hinge_Left E2M-6510411-G60 1 3 Hinge_Right E2M-6510711-G60 1
10-10:Remove Inverter Cable, Then remove Display Module; 1 Display Module S1J-690A004-S02 1
10-11:Remove Inverter Module 3G Antenna WLAN Antenna; 1 INVERTER S78-3300450-SG3 1 2 Wireless Antenna_R S79-1800790-V03 1 3 Wireless Antenna_L S79-1800800-V03 1 4 3G Antenna S79-1800780-V03 1
10-12:Remove CMOS Camera Module as below; 1 CMOS Camera Module S1F-0003020-C54 1 2 Camera Cable K10-3006056-H39 1 3 LCD Cover Assy 307-651A511-CG0 1
10-13:Remove Coaxial Cable as below; 1 Coaxial Cable K19-3001017-H39 1 2 Display Module S1J-690A004-S02 1
10-14:Remove 8pcs M2*3mm Screws, Then remove LCD Bracket as below; Note:Screw driver torque is 1.5~2.0kgf.cm 1 Screw E43-1203007-H29 1 2 LCD Bracket_Left E2M-6510511-Y28 1 3 LCD Bracket_Right E2M-6510611-Y28 1
GX620 (MS-1651)screws specification Photo Screw specification Label (M2.5*L5MM) black (M2*L3MM)white (M3*L3.5MM) white (M2.5*L7MM) black
GX620 (MS-1651)screws specification 1 BOTTOM DOOR ASSY total 18Pcs M2.5*5 and 2pcs M2.5*7 screws, specification: Photo Screw specification label (M2.5*L7MM) black (M2.5*L5MM) black
GX620 (MS-1651)screws specification 2 THERMAL-KIT total 7pcs spring Screws 5 6 2 4 7 3 1
GX620 (MS-1651)screws specification 3 TUNER, WIRELESS,MDC CARD and HDD ASSY total 8Pcs screws, specification: Photo Screw specification label (M3*L3.5MM) white (M2*L3MM)white
GX620 (MS-1651)screws specification 4.UPCASE ASSY total 13pcs screws, specification: Photo Screw specification Label (M2*L3MM)white (M2.5*L5MM) black
GX620 (MS-1651)screws specification 5.LCD Bezel total 8pcs screws, specification: Photo Screw specification label (M2.5*L5MM) black
GX620 (MS-1651)screws specification 6. LCD MODULE ASSY total 14cs screws specification: Photo Screw specification label (M2.5*L5MM) black (M2*L3MM)white
GX620 (MS-1651)screws specification 7. UPCASE and LOWER CASES total 3pcs screws, specification: Photo Screw specification label (M2*L3MM)white
8 NB total 1pcs screw, specification: GX620 (MS-1651)screws specification Photo Screw specification label (M2.5*L5MM) black
9. Bluetooth and Audio Board 3pcs screws specification: GX620 (MS-1651)screws specification Photo Screw specification label (M2*L3MM)white
GX620 (MS-1651)screws specification 10. Touch Pad Board total 3pcs screws specification: Photo Screw specification label (M2*L3MM)white