Modular Jack Connectors for High-Speed LAN Transmission TM2R Series Built-in Optical Indicators Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Features. Supports High-Speed LAN Transmission Meets requirements of TIA/EIA-568-B data wiring standard. Single port configuration meeting CAT5e and multiple port configuration meeting CAT5 transmission performance. As such, these products fully support Gigabit Ethernet (000BASE-T) and Fast Ethernet (00BASE-TX) highspeed LAN transmission. 2. Built-in Optical Indicators Optical indicators are integral part of the connectors saving space on customer s board. Compared with LED type indicators, they do not emit any electrical noise.. EMI protection Metal shield covers the outer surfaces of the connectors assuring complete protection against electromagnetic interference. Built-in multiple shield and ground contacts assure reliable connection with the mounting panel as well as with the mating connector.. FCC Standards Meets requirements of FCC Title 7, Part 68, Subpart F. Optical indicator Housing Space saving Optical pipe Optical indicator LED Optical indicator area One additional TM2 multi-port jack can be mounted in the space previously occupied by LEDs. Applications Telecom Hubs, Routers, Bridges and ATM Transmission Equipment, Ethernet Switches and Networking Equipment, Test and Measurement Equipment, Medical Diagnostic Equipment. Built-in LED type (Possibility of electromagnetic noise emission and interference.) Built-in Optical pipe type (No electromagnetic noise emission.) 202.6
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission Product Specifications Ratings Current rating Voltage rating A 25 V AC Operating temperature range-25ç to +80ç (Note) Item Specification Conditions 0.Insulation resistance 02.Dielectric Withstanding Voltage (between adjacent contacts) 00 M ohms min No flashover or insulation breakdown 00 V DC 500 V AC / one minute Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 0.Withstanding voltage (between contact and shield) No flashover or insulation breakdown 0.Contact resistance 20 m ohms max. 05.Vibration 06.Shock 07.Durability (mating/unmating) 08.Temperature cycle 09.Humidity 0.Salt Spray Note :Includes temperature rise caused by current flow. Materials Part Material Finish Remarks Insulator Contact Optical pipe Shield No electrical discontinuity of 5 ms or more Contact resistance: 250m ohms max. No electrical discontinuity of 5ms or more Contact resistance: 250m ohms max. Contact resistance: 250m ohms max. Contact resistance: 250 m ohms max. Insulation resistance: 00 M ohms min. Contact resistance: 250 m ohms max. Insulation resistance: M ohms min. (High humidity) Insulation resistance: 0 M ohms min. (Dry state) Contact resistance: 250 m ohms max. PBT Copper alloy Poly carbonate Copper alloy 500 V AC / one minute 00mA DC Frequency: 0 to 55 Hz, single amplitude of 0.75 mm, 2 hours / axis Acceleration of 90 m/s 2, ms duration, sine half-wave waveform, cycles in each of the axis 200 cycles (Temperature: -55ç/+5ç to +5ç/+85ç/+5ç to +5ç Duration: 0 / 5 / 0 / 5 (Minutes) 5 cycles 500 hours at temperature of 0ç and humidity of 90% to 95% Exposed to density 5% salt water for 8 hours Color: Black Contact area: Gold plating Termination area: Gold plating flash Color: Clear Tin plating UL9V-0 ------- ------- ------- Ordering information Jacks TM2 R - 5 A - 2 2 D - LP (50) 2 5 6 7 8 9 q Series Name TM2 w Connector type R : Jack e Jack type number 5 : PCB Right-angle through hole type r Jack performance level code A : CAT5 (Single row, multi-port) B : CAT5 (Double row, multi port) C : Supports CAT5e (Single port) t Jack opening code 8 : 8 contacts 2 : 8 contacts / ports 8 : 8 contact/6 ports y Number of inserted contacts 8 : 8 contact 2 : 8 contact inserted in ports=2 contacts 8 : 8 contact inserted in 6 ports=8 contacts u Number of rows Blank: Single row D: Double row i Optical pipe LP: With optical pipe inserted Blank: Without optical pipe o RoHS compliant (50) 2
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission Modular Jack Connectors Supporting CAT5e Single Port With Built-in Optical Pipe 6 Contact No. 2 (5.5).75 Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved...7 Part Number CL No. RoHS TM2R-5C-88-LP(50) 222-2892-0-50 YES Single Port Without Optical Pipe (5.5) 0.5 Contact No.7 0.5. 5.75 TM2R-5C PC.9 6. 5.75 0.25 (5.5).6 Contact No. Contact No.2 Contact No..6.75 0.25. (2.8).05 (2.8).05 0.5 6.5 2.5 0.25.05 2 2 (5.5) 0.5 6.5 2.5 0.25.05 2 (5.5) (5.5).7 Contact No.7 TM2R-5C PC Contact No. Part Number CL No. RoHS.9 Contact No.2 TM2R-5C-88(50) 222-289-2-50YES
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission BRecommended PCB mounting patterns With Built-in Optical Pipe Without Optical Pipe Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved..05 6.5 2.5.05 2-Ø.6 8-Ø BPanel Cutout 7.9 8.89 8 6 5. 5.75 2 6.5.8.27 LED location area Contact No. 2-Ø.2 LED light emission area 6.75 MIN MIN 6.75 Printed board edge Connector front edge No conductive traces 2 No ground traces.min 6.5 2.5.05 2-Ø.2 2-Ø.6 8-Ø 7 8 6 8.89 5 2. 5.75 *Recommendations for PCB Design The contact arrangement differs between the contact area side and Printed board side. (,2,,,5,6,7,8 on the contact are side / 2,,,,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. Area indicated should be free of ground traces. Recommended board thickness:.6mm. 5 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. For Both Types, With and Without Built-in Optical Pipe PCB mounting surface.5min. 0.6MIN TM2P--88P () Lock lever 6.5.8.27 Contact No. No ground traces 5 6.75 MIN No conductive traces 2 PCB mounting pattern 8 Other Series 7 6 MIN 6.75 Printed board edge Connector front edge.min.5 + -2 5 2.7MAX 2.2MAX TM2R Series 7 Suggested LEDs TM2R--5C--88--LP 8 6 5 2 LED light emitting center.5max 0.5 Panel side 6. Connector front surface 2.8 0-6.75 0.25 *Recommendations for Panel Design The shield contacts should connect with the panel cut-out on all sides. Note: IPA cleaning at room temperature is recommended for the cleaning of this product. When an aqueous cleaning agent is to be used, there is a concern that the light pipe (made of polycarbonate resin) may change color; therefore, please make a selection based on a table showing the effects on the resin. These tables are issued by the various manufacturers of cleaning agents.
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission Modular Receptacles Supporting CAT5 Single row/ multiple ports, with Built-in Optical Pipe Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. BRecommended PCB mounting patterns 6MAX 2.7 8. -Ø2 MIN -Ø2 2-Ø.2 Part Number TM2R-5A-22-LP(50) 6 7 2 5 8 58.9.9 LED location area LED light emission area.97 Contact No. No conductive traces 2 5.8 CL No. RoHS 222-287-50YES 8.89 6.5.8.27 5.8 (6) 2-Ø 8. 5.525 2.5.97 Printed board edge Connector front edge 0.5 (.5) Contact No.2 0.25 0.5 Contact No. Contact No.7. 5.8 2.5 8. 58.9 0.25 5.525 2.7.. 59.8.9 Contact No. CL-220 Series.9 2.7 SML-020 Series 0. 2.7 0.6.5 SML-00 Series 0.9.5.6 2.7..2.9 5.8 8. 5..6 2.7 (6) 0.75 5. LED Mount Area Dimensions 25.9 (6).7 5. *Recommendations for PCB Design The contact arrangement differs between the contact area side and Printed board side. (,2,,,5,6,7,8 on the contact are side / 2,,,,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. Recommended board thickness:.6mm. To assure that the indicator light pipes operates correctly the LED s must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. Suggested LEDs Series Name Manufacturer CL-220 SML-00 SML-020 Citizen Electronics Co., Ltd. Rohm Co., LTD Rohm Co., LTD PCB mounting pattern 2 6 8 6 7 5 7 2 5 8 5
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission BRecommended Panel Cutout PCB mounting surface 5.8 Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 0.5 Panels Side TM2P-- 88P () Connector front surface Lock lever.9 59.6.5 0 -.5MIN 0.25.97 5 + - 2.5 6 MAX 0.MIN Shield spring contact *Recommendations for Panel Design The shield contacts should connect with the panel cut-out on all sides. Note: IPA cleaning at room temperature is recommended for the cleaning of this product. When an aqueous cleaning agent is to be used, there is a concern that the light pipe (made of polycarbonate resin) may change color; therefore, please make a selection based on a table showing the effects on the resin. These tables are issued by the various manufacturers of cleaning agents. 6
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission Double row / multiple port, with Built-in Optical Pipe Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. TM2R-5B-22D-LP(50) TM2R-5B-88D-LP(50) Part Number TM2R-5B-22D-LP(50) TM2R-5B-88D-LP(50) CL No. 222-2879--50 222-2885--50 BRecommended PCB mounting pattern 6 MAX 9. Upper row LED mount position Lower row LED mount position...9 MIN - Ø2 2- Ø.2.2 D- Ø (6) A B.97 0.5 Contact No. 0.25 C D Lower row connectors contacts PBT 2 5 8 6 7 7 6 8 5 2.9 Upper row Contact No. 28.6 Lower row (6) 5.8 8. 27.9 0.75 (.5) 0.25 2..9 9.. 2.5.9 Upper row connectors contacts 7.7 A B C D RoHS 59.8.9 5.8 58.9 YES 87.2 69.85 8.75 86.87.9 7.7 Contact No. 8 5 2 7 6 6 7 2 5 8 A B LED light emission area E- Ø2 No conductive traces 2 C.97 8.89 6.5.8.27 Upper row contact hole Lower row contact hole 2.5 5.8 8. 2..9 22.25 Printed board edge Connector front edge 2.5 (6) 22.25.7 0.5 28 Part Number TM2R-5B-22D-LP(50) TM2R-5B-88D-LP(50) CL No. 222-2879--50 222-2885--50 A B C D E 58.9.9 5.8 6 86.87 69.85 8.75 96 6 *Recommendations for PCB Design The contact arrangement differs between the contact area side and Printed board side. (,2,,,5,6,7,8 on the contact are side / 2,,,,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. Recommended board thickness:.6mm. To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. PCB mounting pattern Other Series TM2R Series 7 5 8 5 2 8 6 2 7 6 2 6 8 6 7 5 7 2 5 8 Suggested LEDs Series Name Manufacturer CL-220 Citizen Electronics Co., Ltd. 7
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission BPanels Cutout Shield spring contact spring 28. PCB mounting surface Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 0.5 Panel Side Part Number TM2R-5B-22D-LP(50) TM2R-5B-88D-LP(50) TM2P -- 88P ().5MIN A B CL No. 222-2879--50 222-2885--50 Lock lever.97 5 + -2.5 0. MIN A B RoHS.9 59.60 YES 69.85 87.5 TM2R -- 5B -- * * * * D -- LP Connector front surface 6 MAX.5 0 - *Recommendations for Panel Design 0.25 The shield contacts should connect with the panel cut-out on all sides. Note: IPA cleaning at room temperature is recommended for the cleaning of this product. When an aqueous cleaning agent is to be used, there is a concern that the light pipe (made of polycarbonate resin) may change color; therefore, please make a selection based on a table showing the effects on the resin. These tables are issued by the various manufacturers of cleaning agents. 8
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission BTechnical Documentation CAT5e Transmission Characteristics Data Representative values of the various transmission characteristics data for fully mated receptacle (TM2R-5C-88-LP) and plug (TM2P-88P). All plugs in the TM2R-5C Series that were manufactured based on the De-embedded method of the TIA/EIA-568-B.2 standard and meet performance requirements of CAT5e single transmission. Note:These data are for the listed connector combination. Inquire with your Hirose Electric account representative about other combinations. Signal Attenuation 0.5 Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Attenuation(dB) NEXT(dB) 0. 0. 0.2 0. 0 0 020005060708090 0 Frequency(MHz),2,6,5 7,8 CAT5e Spec Near-End Crosstalk (NEXT) Data Return Loss 20 00 80 60 0 20 0 0 020005060708090 0 Frequency(MHz),2-,6,2-,5,2-7,8,6-,5,6-7,8,5-7,8 CAT5e Spec 80 Return Loss(dB) 60 0 20 0 0 020005060708090 0 Frequency(MHz),2,6,5 7,8 CAT5e Spec 9
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission Far-End Crosstalk (FEXT) 20 00 FEXT(dB) 80 60 0 Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 20 0 Propagation Delay Delay(ns) 2.5 2.5 0.5 0 Propagation Delay (Delay Skew) 0 020005060708090 0 Frequency(MHz),2-,6,2-,5,2-7,8,6-,2,6-,5,6-7,8,5-,2,5-,6,5-7,8 7,8-,2 7,8-,6 7,8-,5 CAT5e Spec 0 020005060708090 0 Frequency(MHz),2,6,5 7,8 CAT5e Spec Delay Skew(ns)..2 0.6 0. 0.2 0 0 020005060708090 0 Frequency(MHz) Measurement Value CAT5e Spec 0
TM2R Series Modular Jack Connectors for High-Speed LAN Transmission BReference Documentation CAT6 Certification Received Only the high quality plugs in the TM2R-5C Series (based on the De-embedded method of the TIA/EIA-568-B.2 standard) clear CAT6 single transmission performance. A certificate was issued by the GHMT, independent European testing company. Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Certificate of Acceptance Return Loss NEXT
Powered by TCPDF (www.tcpdf.org) TM2R Series Modular Jack Connectors for High-Speed LAN Transmission GUIDANCE FOR MODULAR CONNECTORS Modular Connector Terminal Numbers Unless otherwise specified, see the figures below for the terminal numbers of the product. Plug Jack (mating face) Dec..207 Copyright 207 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Attention to Plug Mating Contact No. Use only plugs conforming to FCC standards. Please pay particular attention to dimensions shown right. Contact No.8 Opening Size and Number of Conductors(6-Conductor) FCC PLUG DIMENSIONS See the figures below for the relationship between the opening size and the number of conductors of the jack connectors. Models 6 and 62 are obtained by removing pin and 2 pins, respectively, from both sides of model 66.For details, please contact us for drawings because only standard models are shown in the catalogs. Recommended Soldering for Modular Dip Connectors Flow solder (automatic soldering machine) Pre-heat : 90-0ç Pre-heat time : 20 seconds maximum Solder temperature : 20-260ç Soldering time : 0 seconds maximum Hand soldering Soldering iron tip temperature : 50ç Soldering temperature : 5seconds maximum Soldering iron output : 0-0W Note: When soldering, use care not to apply excessive force to the connector terminals. Recommended Solder composition: Paste, 96.5%Sn/.0%Ag/0.5%Cu Contact No.8 Model 66 Model 6 Model 62 5.89-6.5 Contact No. 6-,Nakagawa Chuoh-2-Chome,Tsuzuki-Ku,Yokohama-Shi 22-850,JAPAN TEL: +8-5-620-526 Fax: +8-5-59-726 http://www.hirose.com http://www.hirose-connectors.com 2 The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 06/202. Contents are subject to change without notice for the purpose of improvements.