SECOND SHOOTER PLUS USER GUIDE WHAT YOU LL NEED Second Shooter Plus Slider Motor Mount Camera Control Cable (or external intervalometer) TABLE OF CONTENTS The Controller... 2 Getting Started: Hardware Set-Up - Slider Motor... 3 - Pan & Tilt Axis... 6 - Intervalometer Connect... 6 - Bridge Mode... 7 Powering Up The System... 7 Power Up Menu - Program Move... 8 - Manual Move... 11 - Turntable... 11 - Settings... 11 Using kos... 12 Updating Firmware... 12 1
THE CONTROLLER a) Menu Button Navigate backwards to the previous menu with this button. b) Directional Arrows The directional arrows can be used to navigate through the menu and also control the Left/Right movement of the Slider motor, Left/Right movement of the pan motor, and the Up/Down movement of the tilt axis. Press and hold (for 3 seconds) Left/Right or Up/Down to swap move orientations. c) Enter Button Use this button to select options through the menu. d) Shift Button This button in conjunction with other buttons allows for secondary controls. Shift + Directional arrows increases speed during set up to allow moves to be programmed faster Shift + Enter turns the LED Light on/off Shift toggles backlight on/off during timelapse move a) b) c) d) e) Power Port Connect the supplied AC wall power cord or a 12V DC cable for battery power. h) f) USB Port Connect the Controller to a computer via the supplied USB cable to update firmware. g) Two Expansion Ports Connect to various external accessories such as the Digital Control Center, while at the same time connecting two controllers together in Bridge Mode. h) Wire Clip Connect the power cord through this clip to prevent unwanted disconnection. i) LED Light Press Shift + Enter to turn off/on. e) f) g) l) j) IN Port Used to connect external intervalometer or bulb ramper k) OUT Port Used to connect a camera via the Camera Control Cable for intervalometer control of the camera by the Second Shooter Plus, or to connect to a bulb ramping device that supports receiving an external trigger signal. l) Cat5 Ports (Slider, Pan, Tilt) Connect each axis to corresponding port via provided CAT5 cable. i) k) j) 2
GETTING STARTED: HARDWARE SET-UP SLIDER MOTOR 1. Choose your desired motor speed by arranging the proper combination of motor pulleys. The metal pin on the Slider motor is to be used for storing the extra pulley LARGE PULLEY SMALL PULLEY PULLEY STORAGE 2. To remove the pulley installed on the Slider motor, simply pull outward away from the motor. 3. To install the pulley, simply push the pulley onto the motor shaft while aligning the holes. Be sure to hold the belt in place while installing. 3
4. Install the Small Pulley onto the Slider Motor. The pre-installed belt (labeled 110XL) on the Slider Motor is to be used in most applications. However, if using the Small Pulley in conjunction with the Shuttle Pod, Shuttle Pod Mini or Pocket Dolly v2.0 follow steps 5-6. 5. Place the smaller belt (labeled 100XL) around the Small Pulley. 6. Mount the Slider Motor onto the Motor Mount utilizing the threaded holes nearest to the pulley on the back side of the motor. 7. Choose between the following pulley combinations: Fast, Normal and Slow. FAST (LOW TORQUE) *This combination is only compatible with CineSlider, Philip Bloom and Stealth sliders. 4
NORMAL *This combination requires the pulley from the Motor Mount Kit to be used on the slider. SLOW (HIGH TORQUE) 8. Mount Slider motor to slider using a Kessler Motor Mount. 9. Connect CAT5 cable from Slider motor to the SLIDER port on the Controller. 5
PAN & TILT AXIS 1. Mount your Pan & Tilt head utilizing the 3/8-16 and ¼ 20 holes on the underside of the Head. (Recommended Mounting: Kessler Kwik Release + 3/8-16 Kwik Short Plate) 2. Connect CAT5 cable from the side of the Pan base to the PAN port on the controller. 3. Connect CAT5 cable from the Tilt axis to the TILT port on the controller. 4. Plug in power supply. INTERVALOMETER CONNECT 1. For time lapse or stop motion, connect a Camera Control Cable to the out port on the controller to the camera. 6
BRIDGE MODE By utilizing one of the available expansion ports, users can link two Second Shooter Plus controllers or a Second Shooter Plus and first generation Second Shooter controller to have 6-axes available simultaneously. In order to get started with Bridge Mode, users will need to connect each of the controllers with a Bridge Cable.* In addition to the Second Shooter Plus Expansion Port being used to connect to Controllers in Bridge Mode, it can also be utilized to connect to motion control accessories, such as the Digital Control Center SETTING UP BRIDGE MODE Plug in the Bridge Cable* into one of the expansion ports on the bottom of each controller, and connect your motors to the CAT5 ports on the top of the controllers. Once the controllers are powered on, in the Power Up Menu indicate if the controller is going to be a master or slave unit. (If bridging a Second Shooter Plus and first generation Second Shooter Controller you will want to set the Second Shooter Plus controller as the master unit.) You can now program a move or do a manual move like normal. When (Master Active) is shown on the Master controller the arrow buttons on each controller will control the motors connected to that controller. To be able to control the motors connected to the slave unit through the master unit double tap shift. The controller will now show (Slave Active) and pressing the arrow buttons on the master unit will control the motors connected to the slave unit. * Although these cables are similar to other RJ-11 cables, DO NOT use any other cable for bridging Second Shooter Controllers. Doing so may put your system at risk for damage. POWERING UP THE SYSTEM To Power on your Second Shooter Plus simply connect the controller to a power source and the unit will automatically power on. Powering on while holding SHIFT + ENTER will reset the controller to factory defaults. POWER UP MENU Upon power up, you will see 4 menu items. If no item is selected within 30 seconds the controller will boot into the main menu with the same selection as the previous time the controller was booted. STANDALONE: Used for a single controller set up. To enter this mode simply press ENTER MASTER/SLAVE: Used if operating with two controllers in bridge mode to determine which unit is the Master and which is the Slave unit. To change these setting SELECT MASTER/SLAVE with the ENTER key and then SELECT either MASTER OR SLAVE and press ENTER. 7
WIFI SETTINGS: Used to toggle between WIFI Enabled and Disabled. To toggle SELECT WIFI Enabled with the ENTER key. Select MENU to exit WIFI Settings, the controller will automatically reboot with WIFI Disabled. Repeat to re-enable WIFI. To connect Second Shooter Plus via USB the WIFI should be disabled on the controller MOTOR OPTIONS AXIS ENABLE/DISABLE: Used to Enable and Disable individual axes. To disable an axis, highlight desired axis with the UP/DOWN arrow key and press ENTER. The axes will be crossed out, showing that it is disabled. FAST MODE: Used to enable or disable Fast Mode. Press ENTER to toggle between Fast Mode Enabled and Disabled QUIET MODE: Used to enable or disable Quite Mode. Press ENTER to toggle between Quite Mode Enabled and Disabled. When Quite Mode is enabled Motor RPM s can be changed from 1,000-4,000 by highlighting Quite RPM with the arrow key pressing ENTER and then changing the speed with the UP and DOWN ARROWS and pressing ENTER. MAIN MENU Once the power up menu is exited, the main menu is displayed with the following menu items: PROGRAM MOVE: Select PROGRAM MOVE to set up a 2 or 3 key frame move. (Page 8-10) MANUAL MOVE: Select MANUAL MOVE to use the controller to move your axis manually using the directional buttons on the Second Shooter Plus controller. (Page 10) TURNTABLE: Select TURNTABLE to use the controller for continuous panning (Page 10) SETTINGS: Select SETTINGS to get to, OPERATING MODE, CONTROL OPTIONS, FIRM- WARE UPDATE AND LASH COMPENSATION (Page 11) PROGRAM MOVE Select PROGRAM MOVE to choose 2 or 3 key frames for the move. (If using a Master/Slave configuration press SHIFT twice to toggle between Master/Slave motors (Page 7)) Move your motors to desired beginning position and press ENTER to SET 1ST KEY FRAME. Move motors to desired 2nd position and press ENTER to SET 2ND KEY FRAME. If setting up a 3 key frame move then move motors to desired 3rd position and press ENTER to SET 3RD KEY FRAME. Now choose one of the following shooting modes LOOP/SCRUB: Loop your 2 or 3 key frame move for a set amount of time or manually Scrub through the 2 or 3 key frame move (Page 8-9) RUN ONCE: Run through a 2 or 3 key frame move one time (Page 9) TIME LAPSE: Create a basic or complex timelapse with a 2 or 3 keyframe move (Page 9-10) 8
LOOP/SCRUB STOP MOTION: Manually or auto advance through each position of a 2 or 3 key frame move to achieve a flawless stop motion. (Page 10) Set TIME and RAMP values by selecting with Enter and adjusting with the Up and Down arrows: Time The amount of time it will take to complete entire move Ramp Percentage value indicates the change in speed of the movement over the entire move. The time value to the right shows how fast/slow the system gets up to the top speed or how fast/slow the camera comes to a stop. Runtime Optimization: Press SHIFT twice to auto calculate the fastest move between keyframes. Fig. A Press ENTER to select RUN. RUN ONCE Scrubbing Press ENTER while Looping to enter SCRUB mode. This feature will allow you to manually advance the position of the Slide, Pan & Tilt axis within the programmed move by holding the LEFT or RIGHT arrow button. Set TIME and RAMP values by selecting with Enter and adjusting with the Up and Down arrows: Time The amount of time it will take to complete entire move Ramp Percentage value indicates the change in speed of the movement over the entire move. The time value to the right shows how fast/slow the system gets up to the top speed or how fast/slow the camera comes to a stop. Runtime Optimization: Press SHIFT twice to auto calculate the fastest move between keyframes. 9
Fig. A Press ENTER to select RUN. TIME LAPSE Select SHOOT/MOVE/SHOOT or CONTINUOUS mode: Shoot/Move/Shoot Camera will only fire when not moving. That is, the camera will fire, move to next position, stop and fire. Continuous Camera will move without stopping and fire throughout the duration of the move * If using a 3rd party intervalometer, select Continuous and set the overall run time by increasing or decreasing the Photos value. The exposure, delay and photo values will not be used. Set the RAMP value by selecting with Enter and adjusting with the Up and Down arrows: Ramp Percentage value indicates the change in speed of the movement over the entire move. The frame value to the right shows how many images until the system gets up to the top speed or how many images until the camera comes to a stop. Select START to begin the time-lapse. STOP MOTION The motors will move into the start position (1st key frame) and the backlight will turn off. Press the Shift button to toggle the backlight on/off. Press the Enter button to Pause/ Resume the time lapse move. Set values for #PHOTOS & RAMP: #Photos - Indicates the number of photographs taken during the entirety of the move Ramp Percentage value indicates the change in speed of the movement over the entire move. The frame value to the right shows how many images until the system gets up to the top speed or how many images until the camera comes to a stop. 10
Select AUTO ADVANCE or MANUAL ADVANCE by pressing Enter to toggle selections. Auto Advance - In this mode, after the camera fires, the system will automatically advance to the next position in the movement Manual Advance - After firing the photo, you will hit Left or Right to move the camera into the next/previous position in the move Select NEXT by pressing Enter. Select SNAP to trigger the camera and repeat for auto advance. Select SNAP to trigger the camera. Press the Left or Right arrow to move the camera into the next/previous position for manual advance. Repeat. MANUAL MOVE Select MANUAL MOVE to do a live move without programming. Set Speed: Select Speed by pressing ENTER. Adjust speed with UP/DOWN arrows and press ENTER to set. Set Ramp: Select Ramp by pressing ENTER. Adjust ramp with UP/DOWN arrows and press ENTER to set. Set Cal Limits: Select Cal Limits. Use controller to position motors to desired start position and press ENTER to set BEGIN, then position motors to desired end position and press ENTER to set END. Select START to begin Manual Move. TURNTABLE SETTINGS Select TURNTABLE for continuous panning. The speed can be adjusted by pressing the Up or Down arrow at any time. Press the pan Left or Right arrow to start/stop panning. Operation Mode Takes you back to the Power Up Menu. Control Options Inverts Controls depending on user preference Firmware Update See Updating Firmware section Lash Compensation Set up a pre-move to remove any lash in the system due to a change in direction. 11
USING KOS WITH SECOND SHOOTER PLUS To use the Second Shooter Plus controller with kos software, you will need kos for Second Shooter v4.5 or greater for Mac, Windows or ipad. The Second Shooter Plus is not compatible with kos software versions prior to v4.5. CONNECTING TO KOS VIA USB Connect USB/Micro USB cable to computer and Second Shooter Plus controller. Open kos and click connect. Your Second Shooter Plus will automatically connect to kos. CONNECTING TO KOS VIA WIFI Press the Menu button until the main version screen is displayed. Once the version is displayed, the Operation Mode menu will display. If the WiFi menu option reads WiFi Enabled, the WiFi access point is active. Proceed to #4 If the WiFi menu option reads WiFi Disabled, select it and press the Enter button, your Second Shooter Plus will reboot and will now say WiFi Enabled. On your computer or tablet you will now see a WiFi network named 2ndShooter+. Connect to that wireless network. Once connected to the 2ndShooter+ network, open kos and it will automatically connect to your Second Shooter Plus via WiFi UPDATING FIRMWARE Download and extract the attached zip file. There are 2 files within the zip. The one you will need is SECONDSHOOTER+.IMG. Plug in the power cord for the Second Shooter controller. Plug the micro-usb to USB cable from the USB port on the computer into the micro-usb port on the controller. Once system powers up, navigate to SETTINGS. In SETTINGS, find and select FIRMWARE UPDATE. The Controller will display FIRMWARE UPDATE READY The Controller will show up as a USB device on your computer titled 2nd Shooter. Go to the location where you extracted SECONDSHOOTER+.IMG. 12
Click and drag SECONDSHOOTER+.IMG to the USB device titled 2nd Shooter and release. The system is now updating. The Controller s screen will detail the update process. Do not remove power to the controller during firmware update process. Select REBOOT to restart the controller. MAC Users: Once Reboot is selected during the update firmware process, a Disk Not Ejected Properly message appears on the Mac OS X desktop. Users may simply close this message without issue. As the system restarts, confirm the splash screen shows the latest firmware version across the bottom. TERM REFERENCE GUIDE Exposure The length of time the camera s shutter is open when taking a photograph Delay Amount of time between photos Ramp Rate of Change of acceleration/deceleration Visit support.kesslercrane.com for manuals, support videos, references & more 13