DIGITAL PANORAMIC Installation Manual Release 14 June 2005
Revision history Revision history Rev. Date Page/s Modification description 0 02.08.03 First release 1 14.06.05 All ROTOGRAPH D release DIGITAL PANORAMIC
Revision history THIS PAGE IS INTENTIONALLY LEFT BLANK DIGITAL PANORAMIC
Contents Contents 1. MINIMUM SYSTEM REQUIREMENTS 3 2. USB2 HUB INSTALLATION 4 2.1 STRATO 2000 D USB2 HUB installation... 4 2.2 ROTOGRAPH D USB2 HUB installation... 7 3. USB2 HUB DRIVER S INSTALLATION 8 3.1 USB2 HUB driver s installation Windows XP... 8 4. PANORAMIC DIGITAL DRIVER INSTALL GUIDE RD 15 5. CALIBRATION FILE FOR DIGITAL PANORAMIC 24 This publication can only be reproduced, transmitted, transcribed or translated into any human or computer language with the written consent of VILLA SISTEMI MEDICALI S.p.a. This manual in English is the original version. i DIGITAL PANORAMIC
Contents THIS PAGE IS INTENTIONALLY LEFT BLANK DIGITAL PANORAMIC ii
1. MINIMUM SYSTEM REQUIREMENTS NOTE: No system of lower specification than that listed below should be used. It will not allow correct functioning. Motherboard: P4 or equivalent RAM Memory: 512 MB recommended Hard disk: 80 GB Operating system: Windows XP Service Pack 2 Graphic card: 64 MB CD ROM Reader: 24X minimum USB2 port: yes Keyboard and mouse: yes Monitor: High resolution multi sync (1024:768 @ 32" bts) (CR:400) (Pixel dot pitch.25) Removable hard disk, or other backup system Direct X Image Application Software NOTE: The USB 2 port is strictly required for the functioning of the acquisition. Due to restriction of USB 1 or USB1.1 devices, those devices cannot be connected to the same HUB controller where the Panoramic Board is connected, because the acquired image may be corrupted. 3 DIGITAL PANORAMIC
2. USB2 HUB Installation 2.1 STRATO 2000 D USB2 HUB installation STRATO 2000 D has two USB 2 HUBs installed to exchange data between the digital panoramic board and the PC and related software. Before starting the operation, the operating system (Windows XP ) must recognise the hardware connected. NOTE: Although not strictly required for latest versions of Windows, we recommend following the procedure indicated hereafter. This procedure must be performed only at the installation. 1. Power off the STRATO 2000 D and, with the USB cable disconnected from the PC and having the superior cover of STRATO 2000 D open, disconnect the two USB cables from the intermediate HUB (refer to following picture). 2. Power on the PC and wait until it finishes the start up procedure; at this point, insert the USB cable into the second HUB (the one located near the base column). Plug in the second end of this cable into the USB port of the PC. 3. Power on the STRATO 2000 D; the operating system of the PC will automatically recognise the new hardware connected; in Windows XP the message that a new hardware has been detected will be shown on the display. The driver's are automatically loaded. DIGITAL PANORAMIC 4
5 DIGITAL PANORAMIC
4. When the process is finished (message "New hardware loaded..."), plug in the USB cable connecting to the PC into the intermediate HUB. The cable that must be inserted has a squared terminal; leave the rectangular terminal not connected. 5. The operating system will remake the procedure of new hardware detection and drivers loading, as described on point 3 above. 6. At this point, plug in the latest connector; the operating system will detect the digital panoramic board; due to the fact that this hardware is not a standard one, the procedure described in the following pages must be performed. This procedure depends on the operating system installed on the PC; please refer to the appropriate chapter. DIGITAL PANORAMIC 6
2.2 ROTOGRAPH D USB2 HUB installation ROTOGRAPH D has only one USB 2 HUB, located on the rear part of the column. This HUB requires a separate line voltage plug. The HUB is required in order to allow the exchange of information between the Digital Panoramic board (sensor) and the PC and related software. Before starting the acquisition, the operating system (Windows XP ) should recognise the hardware connected. NOTE: Although not strictly required for latest versions of Windows, we recommend following the procedure indicated hereafter. This procedure must be performed only at the installation. 1. Power off the ROTOGRAPH D and disconnect the cable coming from the sensor board (the one coming out from the plastic corrugate tube) from the HUB if already connected. 2. Power on the PC and wait until it finish its start up procedure. Insert the USB 2 cable into the HUB. 3. Power ON the HUB itself, plugging it into the line voltage plug. Wait until the operating system recognises the new hardware. 4. Connect the USB 2 cable coming from the sensor to the proper connector of the HUB and power ON the ROTOGRAPH D. The procedure of "new hardware found" will start automatically. 5. Proceed with the paragraph Error! Reference source not found. or 3, according to the operating system installed on the PC. 7 DIGITAL PANORAMIC
3. USB2 HUB driver s installation 3.1 USB2 HUB driver s installation Windows XP The operating system displays the following image, meaning that it had detected new hardware, and asks for the corresponding driver. 1. Select the option "Install from a list or specific location" and click on "Next"; the following windows will be displayed. DIGITAL PANORAMIC 8
2. Select "Don't search. I will choose the driver to install". Click on "Next". Be sure to have already the CD on the reader. 9 DIGITAL PANORAMIC
3. Select the type of hardware to be installed by clicking on "Universal Serial Bus controllers", then on "Next"; the following windows will be displayed. 4. Click on the tab "Have Disk". DIGITAL PANORAMIC 10
5. Click on "Browse"; the following windows will be displayed. 6. Click on "My computer" on the vertical left bar, and search for the driver in the location "D:\Pano_install\Driver_Pano". In this example, the letter D: represents the CD ROM drive, and it is related to the PC in use. Select the file "ow_usb.inf" and click on "Open". 7. The location of the driver should appear on the command line. Click on "OK". 11 DIGITAL PANORAMIC
8. Select "DIGITAL PANORAMIC board" and click on "Next"; the following windows will be displayed. 9. This message is a Warning; click on "Continue Anyway". DIGITAL PANORAMIC 12
10. Click on "Finish" button to terminate the driver installation. 11. To check if the driver was correctly installed and the unit is functioning, right click on "My Computer", "Properties" and then click on "Device Manager" button. 13 DIGITAL PANORAMIC
12. The panoramic is installed in "Universal Serial Bus controllers". Clicking on it, the following window will appear; the "DIGITAL PANORAMIC board" is correctly installed. DIGITAL PANORAMIC 14
4. Panoramic Digital Driver Install Guide RD The following steps should be completed on a Windows XP machine with the latest version of ProImage installed. Steps: 1. Insert the Dent X Panoramic Digital Driver Version 3.0 CD. 2. The following window will open after a few seconds: 3. Click on Next. 15 DIGITAL PANORAMIC
4. Select I accept the terms in the license agreement. 5. Click on Next. DIGITAL PANORAMIC 16
6. Click on Next. 7. Click on Install 17 DIGITAL PANORAMIC
8. After a few minutes the following window will be displayed: 9. Click on Finish. 10. Window will close. 11. Connect the Rotograph D (USB 2.0 connection). 12. The Fount New Hardware Wizard window will open. DIGITAL PANORAMIC 18
13. Select No, not this time. 14. Click on Next. 19 DIGITAL PANORAMIC
15. Click on Next. 16. The following window will open: 17. Click on Continue Anyway. DIGITAL PANORAMIC 20
18. Enter D:\Pano Drivers and click on OK. 19. Click in Finish. 20. Verify the following windows message is received: 21 DIGITAL PANORAMIC
21. Select Start All Programs AFP Imaging Digital Pan Set System. 22. The following window will open: 23. Chose Rotograph Digital from the drop down menu. 24. Click on OK. 25. Open ProImage and select Edit Preferences Hardware Type Strato Digital. 26. Select File Update Patient. 27. Verify the Select Patient window has the correct icons, as displayed below: DIGITAL PANORAMIC 22
28. Close ProImage. 29. Disconnect the Rotograph D. 23 DIGITAL PANORAMIC
Program installation for Network Software 5. CALIBRATION FILE FOR DIGITAL PANORAMIC The unit is shipped with a floppy disk or CD; this contains the calibration file for the specific CCD sensor installed on the machine. NOTE: The disk must be kept in a safe place in order to be able to reinstall it in case of system crash. In any case, Dent X will be able to deliver a copy of this file. The small mini CD disk contains a file named "pano_oem_dspr.bmp". This is not an image file, so it cannot be opened by standard image software. This file must be copied, on the PC and the location where to copy it depends on the operating system in use. The copy operation can be performed with the standard Windows procedure, using Explorer. Open Explorer clicking on "Start", "Programs" and locate "Explorer". A double click will start it. The "Copy" and "Paste" procedure can be used to copy the file into the subfolder hereafter specified: Windows XP: copy it on the folder "C:\windows\system32"; to perform this you must be logged in as "System Administrator". DIGITAL PANORAMIC 24
Program installation for Network Software 25 DIGITAL PANORAMIC
Cod. 6909906103_Rev.1 Dent X An AFP Imaging Company 250 Clearbrook Rd. Elmsford, NY 10523 Office 914 592 6100 Fax 914 592 6769