6. Install the Nureva image alignment module NAM2-1 Install the NAM2-1 and connect it to the projectors and PC(s). PROVIDED t - Nureva image alignment module NAM2-1 u - Power supply t u YOU MUST PROVIDE HDMI cables x 2 Ethernet cables Quantity depends on your cabling configuration Wi-Fi router (See notes on page 24 and page 25) 1 Connect the NAM2-1, projectors and PC(s) For a double panoramic system For a triple panoramic system If your system has one PC Follow the connection diagram on page 24 If your system has two PCs Follow the connection diagram on page 25 Follow the connection diagram on page 25 The image alignment module is connected to the outer two PCs and the outer images are adjusted to match the static center image. May 2016 23
Follow this diagram if you have A double panoramic system with one PC The PC needs to access the NAM2-1 network in addition to the local network. Ensure the PC is set up to use the IP address range 192.168.0.xxx. The NAM2-1 s factory setting IP addresses are Channel A 192.168.0.11 Channel B 192.168.0.12 NOTE: If the PC is hard-wired via Ethernet to your local network, use Wi-Fi and a wireless router connected to the NAM2-1. See page 5 for the router minimum operating requirements. May 2016 24
Follow this diagram if you have OR A double panoramic system with two PCs A triple panoramic system Both PCs need to access the NAM2-1 network in addition to the local network. Ensure the PCs are set up to use the IP address range 192.168.0.xxx. The NAM2-1 s factory setting IP addresses are Channel A 192.168.0.11 Channel B 192.168.0.12 NOTE: If the PCs are hard-wired via Ethernet to your local network, use Wi-Fi and a wireless router connected to the NAM2-1. See page 5 for the router minimum operating requirements. May 2016 25
7. Download Span software and touch driver, and calibrate touch Download the software and touch driver, and use the touch driver to calibrate touch on the projected images. 11 1 Download files Go to span.nureva.com/download.html and download and install the software and touch driver onto each PC. 1 2 Launch touch driver Once the driver has been installed, use the wireless PC keyboard and mouse to click on the touch icon to launch the menu. The calibration process is different depending on if you have a double or triple system and your PC configuration. Follow the steps on page 27 or 28 according to your system s configuration. May 2016 26
Follow these steps if you have A double panoramic system with one PC 1 Settings 2 Matching After selecting the touch driver icon, select the gear icon. Select Number of Displays and choose Dual from the drop-down menu. Select the hand icon and click Matching. The screen will flash a series of dots. Click OK when the matching has completed. 3 Touch Area settings 4 Calibration Select Touch Area Setting and choose Auto from the drop-down menu. The screen will flash a series of dots. Click OK. Select Calibration from the menu and choose Auto from the drop-down menu. The screen will flash a series of dots. Click OK. May 2016 27
Follow these steps if you have OR A double panoramic system with two PCs A triple panoramic system 1 Touch Area settings 2 Calibration Select Touch Area Setting and choose Auto from the drop-down menu. The screen will flash a series of dots. Select Calibration from the menu and choose Manual from the drop-down menu. 3 Run the touch driver on the remaining PC(s) and repeat the calibration steps. May 2016 28
8. Align the projected images Use the Span setup center to align the projected images into a single, seamless image. 1 Install and launch Span setup center The Span setup center is included in the Span wall software download. Install the software and click the Span setup icon from the taskbar. Select Image Alignment. If your system has one PC, the software will open across both screens. If your system has two PCs, launch the software on both screens. For a triple system, launch the software on the two outer screens. 2 Ensure the image alignment settings are correct Tap Settings Select your system's PC/projector configuration Ensure the IP addresses are 192.168.0.11 and 192.168.0.12 Ensure Projector Model (Resolution) is set to 1920 x 720 Ensure Sleep Timer is set to 15 minutes Tap Save May 2016 29
3 Align the projected images The NAM IP connection will go red while it is connecting. Once the IP connection turns green, tap Start Image Alignment. If your system has two pcs, repeat this step on the remaining screens. If your system has three pcs, perform this step on the two outside screens. FOR A DOUBLE PANORAMIC SYSTEM Verify that the projected images overlap in the center by a couple of inches Starting with the larger image, tap and drag the targets on the corners and mid-lines to align the image If necessary, adjust the second image using the same method until both images are squared off and flush along the centerline Click Done on both of the screens May 2016 30
FOR A TRIPLE PANORAMIC SYSTEM You will be adjusting the two outer images to match the center image Verify that each projected image overlaps by a couple of inches Tap and drag the targets on the corners and mid-lines to align the outer images to match the center image Click Done on all of the screens Allow the calibration countdown and the touch auto calibration to complete across both screens 4 Manually calibrate touch Once the auto callibration has completed across both screens, open the Span setup center across all screens: Select Touch Calibration Press and hold the crosshair symbol that appears on the screen until it changes to a darker color Lift your finger and follow the dot to the next location. Repeat this step until the calibration process is complete. Repeat on the remaining screens May 2016 31