All Metals and Long- Types CSM DS_E and Both Detectable from Long Distances times the aluminum detection of previous models Twice the max. Equipped with a function to prevent the detection of aluminum chips chip protection Long- aluminum detection For the most recent information on models that have been certified for safety standards, refer to your OMR website. Refer to Safety Precautions on page 8. Features Detection Distance: Times Previous s * Immunity against aluminum chips has enabled achieving long- detection of aluminum workpieces. The same detection has also been achieved for iron, allowing the -@ to be separated from workpieces made of either metal farther than any other Proximity Sensor. Excellent Performance, with Chip Immunity! Also Detects at Long Distances! EEZ EEZ Chip Immunity EEM EEM Long- (Ferrous Metals) EE EE Standard 5 6 7 8 9 5 6 7 8 9 Sensing (mm) Sensing (mm) * In-house comparison of M8 Shielded Long- s Detection Made Visible An operation indicator that is visible from any direction is provided as a standard feature. This indicator flashes under unstable conditions for easy installation condition verification at a glance. The indicator may be difficult to see from some directions. Visible The indicator is visible from any direction. The indicator is visible from any direction. 8 8 8 Previous Sensor Pre-wired s and Pre-wired Connector s Connector s Embeddable in Metal. The first Long- Sensor that is shielded. Possible to be completely embedded in metal. Workpiece Bracket Protruding Workpiece Embedded Mounting in Metal EEM
Ordering Information Sensors (Dimensions page 9) Standard- type DC -wire, Pre-wired s (Standard Cable Length: m) Appearance Sensing Output Operation mode NO Operation mode NC PNP -B M -B M M mm NPN -C M -C M Shielded PNP -5B M -5B M M8 5 mm NPN -5C M -5C M PNP -B M -B M M mm NPN -C M -C M Long- type DC -wire, Pre-wired s (Standard Cable Length: m) Appearance Sensing Output Operation mode NO Operation mode NC PNP -B M -B M M mm NPN -C M -C M Shielded PNP -8B M -8B M M8 8 mm NPN -8C M -8C M PNP -5B M -5B M M 5 mm NPN -5C M -5C M Long- type DC -wire, Connector s Appearance Sensing Output Operation mode NO Operation mode NC PNP -B-M -B-M M mm NPN -C-M -C-M Shielded PNP -8B-M -8B-M M8 8 mm NPN -8C-M -8C-M M 5 mm PNP -5B-M -5B-M NPN -5C-M -5C-M Long- type DC -wire, Smartclick Pre-wired Connector (M) s Appearance Sensing Output Operation mode NO PNP -B-MTJ.M M mm NPN -C-MTJ.M Shielded PNP -8B-MTJ.M M8 8 mm NPN -8C-MTJ.M M 5 mm PNP -5B-MTJ.M NPN -5C-MTJ.M
Accessories (Order Separately) Sensor I/O Connectors (M, Sockets on One Cable End) is not provided with the Sensor. Be sure to order a Connector separately. (Dimensions S5) (Required for models with Pre-wired Connectors.) A Connector Appearance Type Cable length Applicable Proximity Sensor s m S5F-D-D8-F Smartclick Standard cable Connector, 5 m S5F-D-G8-F Straight -@B-MTJ -@C-MTJ Oil-resistant polyurethane m S5F-D-D8-P cable 5 m S5F-D-G8-P Sensor I/O Connectors (M, Sockets on One Cable End) Standard type (Required for models for Connectors.) A Connector is not provided with the Sensor. Be sure to order a Connector separately. (Dimensions S) Appearance Cable length Sensor I/O Connector model number Applicable Proximity Sensor s m SF-D-DC-F -@C-M Straight 5 m SF-D-GC-F -@B-M m SF-D-D8-F -@C@-M 5 m SF-D-G8-F -@B@-M L-shape m SF-D-DC-F -@C-M 5 m SF-D-GC-F -@B-M m SF-D-D8-F -@C@-M 5 m SF-D-G8-F -@B@-M
Ratings and Specifications Size M M8 M Item -@@ -@@ -5@@ -8@@ -@@ -5@@ Sensing mm±% mm±% 5 mm±% 8 mm±% mm±% 5 mm±% Set to.6 mm to. mm to. mm to 6. mm to mm to mm Differential travel Detectable object Standard sensing object Response frequency * Power supply voltage (operating voltage range) Current consumption Control output Load current Residual voltage % max. of sensing Ferrous metals and non-ferrous metals (The sensing depends on the material of the sensing object. Refer to Engineering Data (Reference value).) : mm : mm : 8 8 mm : mm : mm 5 Hz Hz 7 Hz Hz 7 Hz Hz to VDC ( to VDC), ripple (p-p): % max. 5 mw max. (Current consumption: 5 ma max. at power supply voltage of V) Open-collector output, ma max. V max. (Load current: ma, Cable length: m) : 5 5 mm Indicators NO s: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC s: Operation indicator (yellow) (lit) Operation mode B/C s: NO B/C s: NC (Refer to the timing charts under I/O Circuit Diagrams for details.) Protection circuits Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge suppressor Ambient temperature Operating/Storage: -5 to 7 C (with no icing or condensation) Ambient humidity Operating/Storage: 5% to 95% (with no condensation) Temperature Based on the sensing at C in the temperature range of -5 to 7 C influence ±% max. ±5% max. ±% max. ±5% max. ±% max. ±5% max. Voltage influence ±.5% max. of sensing at rated voltage in the rated voltage ±5% range Insulation resistance 5 MΩ min. (at 5 VDC) between current-carrying parts and case Dielectric strength, VAC, 5/6 Hz for minute between current-carrying parts and case Vibration resistance Destruction: to 55 Hz,.5-mm double amplitude for hours each in, Y, and Z directions Shock resistance Destruction:, m/s times each in, Y, and Z directions Degree of protection IEC IP67 (Pre-wired s and Pre-wired Connector s are oil-resistant to the OMR in-house standard.) Connection method Pre-wired s (Standard cable length: m), Connector s, Pre-wired Connector s (Standard cable length: mm) Cable Approx. g Approx. 5 g Approx. g Connector Approx. g Approx. 5 g Approx. g Weight (packed state) Materials Accessories Pre-wired Connector s Case Sensing surface Clamping nuts Toothed washer Approx. 5 g Approx. 7 g Approx. g Nickel-plated brass Heat-resistant ABS Nickel-plated brass Zinc-plated iron Instruction manual * The response frequency is an average value. Measurement conditions are as follows: Standard sensing object, a between target objects of twice the size of the standard sensing object, and a set of half the sensing.
Engineering Data (Reference Value) Influence of Sensing Object Size and Material - - -5..5.5..5 Stainless steel (SUS) @d t= mm 5..5..5..5.5..5 Stainless steel (SUS) t= mm @d Stainless steel (SUS) @d t= mm 5 5 5 5 5 5-8 - -5. Stainless steel (SUS) @d t= mm. Stainless steel (SUS) @d t= mm.. Stainless steel (SUS) @d t= mm 5 5 5 5 5 6 5 6 Influence of Sensing Object Size and Material - - -5 Stainless steel (SUS) Sensing object size: mm 5..5..5..5 Stainless steel (SUS).5. t.5 Sensing object size: mm 5 6 7. 5.... Stainless steel (SUS) Sensing object size: 8 8 mm 5 6 7 8 t 5
Y Y -8 - -5. Stainless steel (SUS) Sensing object size: mm 5 6 7 8 t. Stainless steel (SUS) Sensing object size: mm 6 8 t. Stainless steel (SUS). t Sensing object size: 5 5 mm 6 8 Sensing Area. -5@. -5@. -@ -8@ -5@ -@ -@ - -9. - -.. 9. Sensing Y (mm) Sensing area () (Thickness:. mm) -@ -8@ -5@. -@ -@ - -9. - -.. 9. Sensing Y (mm) Sensing area () (Thickness:. mm) 6
I/O Circuit Diagrams NPN Output Operation mode Timing charts Output circuit -@C@ (-M/-MTJ) NO Non-sensing area Sensing object Unstable sensing area (%) 8 Rated sensing Non-sensing area Sensing object Flashing Set position Stable sensing area Proximity sensor Yellow indicator Control output Sensing area Proximity sensor Proximity Sensor main circuit Note: Connector s NO s: NC s: Brown Black Blue +V Load V NC (%) Rated sensing Yellow indicator Control output M: MTJ: Compatible Connector Cables: S5F Series SF Series PNP Output Operation mode Timing charts Output circuit Non-sensing area Sensing object Unstable sensing area Set position Stable sensing area Proximity sensor Brown +V -@B@ (-M/-MTJ) NO (%) Non-sensing area Sensing object 8 Rated sensing Flashing Yellow indicator Control output Sensing area Proximity sensor Proximity Sensor main circuit Note: Connector s NO s: NC s: Black Blue Load V NC (%) Rated sensing Yellow indicator Control output M: MTJ: Compatible Connector Cables: S5F Series SF Series Connections for Sensor I/O Connectors Type Proximity Sensor Operation mode Sensor I/O Connector model number Connections NO -@C-M -@B-M : Straight : L-shape SF-D@-@C-F D: -m cable G: 5-m cable Main Circuit SF SF Brown (+V) Blue ( V) Black (Output) DC -wire : Straight : L-shape Main Circuit Brown (+V) White (Blank) Blue ( V) Black (Output) NC -@C-M -@B-M SF-D@-@8-F D: -m cable G: 5-m cable Main Circuit SF Brown (+V) White (Output) Blue ( V) Black (Blank) Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details. 7
Safety Precautions Refer to the Proximity Sensors Technical Guide. WARNING This product is not designed or rated for ensuring safety of persons. Do not use it for such purposes. Never use the product with an AC power supply. Otherwise, explosion may result. Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Designing Influence of Surrounding Metal When embedding the Sensor in metal, be sure that the clearances given in the following table are maintained. d dia. D m n m t t t Table. Influence of Surrounding Metal (Unit: mm) Item - -5 - d dia. 8 D m 5 n 8 7 5 Item - -8-5 * d dia. 8 * D * m 5 n 8 7 5 * If the thickness of the mounting bracket (t) exceeds 5 mm, be sure to install the Sensor so that, d (dia.) 5, and D. Sensing Distance The sensing depends on the sensing object size, material, and thickness. If the sensing object has a thickness of less than mm, the sensing will decrease. In some cases, it may not be possible to detect stainless steel. Use the following graph and the Influence of Sensing Object Size and Material information in Engineering Data (Reference Value) as a reference. and Cuttings Normally aluminum or iron cuttings will not be detected even if they adhere to or accumulate on the sensing surface. Detection signals may be output for the following. If this occurs, remove the cuttings from the sensing surface. Diameter of cutting = d and diameter of sensing surface = D Cuttings in center of sensing surface with d /D (Unit: mm) d Mode Size D -@/@ -5@/8@ 6 -@/5@ 8 Tightening Torque Do not tighten the nut with excessive force. A washer must be used with the nut. Tightening Torque Part A Part B Dimension (mm) Torque Torque -/ 7 5.9 N m 9.8 N m -5/8 5 N m 5 N m -/5 6 9 N m 78 N m D (Shielded ) Pressed against Cutting sensing surface. Sensing Cutting surface Part B Part A Mutual Interference When installing Sensors face-to-face or side-by-side, be sure that the minimum s given in table are maintained. Chart. Mutual Interference (Unit: mm) Item - -5 - A 5 B 5 Item - -8-5 A 5 6 B 5 5 7 8
Dimensions Sensors Pre-wired s -/ (Unit: mm) Tolerance class IT6 applies to dimensions in this data sheet unless otherwise specified. -5/8 dia. 7 7 6 with conductors (Conductor cross section:.5 mm, Insulator diameter:.9 mm), Standard length: m 6 9 dia. 5 with conductors (Conductor cross section:.5 mm, Insulator diameter:.9 mm), Standard length: m M Indicator * Toothed washer M8 Indicator * Toothed washer -/5 6 dia. 5 6 with conductors (Conductor cross section:.5 mm, Insulator diameter:.9 mm), Standard length: m M.5 5 Indicator * Toothed washer * NO s: Operation indicator (yellow) (flashing) Setting indicator (yellow) () NC s: Operation indicator (yellow) () Pre-wired Connector s --MTJ -8-MTJ dia. 7 7 6 Standard length: mm 6 9 dia. 5 Standard length: mm Indicator * M M Toothed washer M8 Indicator * Toothed washer M -5-MTJ 6 dia. 5 6 Standard length: mm Indicator * M M.5 5 Toothed washer * NO s: Operation indicator (yellow) (flashing) Setting indicator (yellow) () NC s: Operation indicator (yellow) () 9
Connector s E F A G D C B M Four indicators * Toothed washer * NO s: Operation indicator (yellow) (flashing) Setting indicator (yellow) () NC s: Operation indicator (yellow) () Item -@-M -8@-M -5@-M A M M8 M.5 B 65 6 6 C 7 D 5 7 9 E dia. 9 dia. dia. F 7 6 G 5 Mounting Hole Dimensions Proximity Sensor dimensions M M8 M + + + Dimension H (mm).5 dia. 8.5 dia..5 dia.
Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMR representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMR MAKES NO WARRANTY OR REPRESENTATI, EPRESS OR IMPLIED, ABOUT N-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron s sole obligation hereunder shall be, at Omron s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMR COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTI OR COMMERCIAL LOSS IN ANY WAY CNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer s application or use of the Product. At Buyer s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATI INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMR PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. OMR Corporation Industrial Automation Company http://www.ia.omron.com/ 5. In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMR Corporation 5 All Right Reserved.