1 SSI interface for absolute encoders, 1 analog output S20-
2 Bosch Rexroth AG Electric Drives and Controls Position detection via absolute encoders with SSI interface Encoder resolution up to 56 bit Transmission frequency up to 2 MHz Gray or binary code Rotation direction reversal Current and voltage measuring ranges Saved device nameplate Diagnostic and status indicators Documentation Data sheet Application description This module is designed for use within an IndraControl S20 station. It is used to detect positions by absolute encoder with SSI interface. An analog output, which serves to specify the command value for a drive control, for example, can be used at the same time. Technical data S20- Local bus interface Designation S20 local bus Connection type Connection for bus socket module Supply for module electronics Connection type Spring-cage connection with direct plug technology Connection data solid / flexible / AWG 0,2... 1,5 mm 2 / 0,2... 1,5 mm 2 / 24-16 Supply voltage 24 V DC Supply voltage range 19.2... 30 V DC (including all tolerances, incl. rippling) Logic voltage U BUS 5 V DC (via bus socket module) Current consumption of U BUS Max. 180 ma Protective circuit Overvoltage protection, reverse polarity protection, transient protection Analog Outputs Connection technology of the actuators 2-wire connection (shielded, twisted in pairs) Number 1 Load / output load current output Up to 500 W Output voltage range 0... 5 V, -5... 5 V, 0... 10 V, -10... 10 V Output current range 0... 20 ma, 4... 20 ma, -20... 20 ma Protective circuit Overvoltage protection, reverse polarity protection, transient protection Characteristics Measurement resolution 16 bits (15 + sign bit) Accuracy 0.1% (of output range end value) Encoder detection Type Symmetrical and asymmetrical encoders Number 1 Description of the input SSI interface
Electric Drives and Controls Bosch Rexroth AG 3 Encoder supply voltage Resolution 24 V DC 8 to 56 bits (configurable) Transmission frequency 2 MHz System times System bus cycle time 2 µs Offset per module 1 µs Load Vibration resistance 5 g according to EN 60068-2-6 Shock resistance 25 g according to EN 60068-2-27 Shock resistance (continuous shock) according 10 g according to EN 60068-2-29 to EN 60068-2-29 Emitted interference Class B according to EN 61000-6-3 Interference immunity According to EN 61000-4 Environmental conditions Permissible temperature (operation) -25... +60 C Permissible humidity (operation) Permissible humidity (storage) Protection category 5 to 95%, no dewing 5 to 95%, no dewing IP20 Dimensions 35 54 122,4 126,1 S20- Dimensions Height H [mm] 126.1 Width B [mm] 35 Length T [mm] 54
4 Bosch Rexroth AG Electric Drives and Controls Ordering information S20- IndraControl S20 analog input module - 1 SSI interface for absolute encoders, 1 analog output R911172544 S20-BS-S Bus base module (spare part) R911173203 S20-SHIELD SET Shield connection kit R911173030 S20-SHIELD-NLS Neutral busbar 3 mm x 10 mm, length: 1000 mm R911173283 S20-SHIELD-SK14 S20-SHIELD-SK5 Shielding terminal 14 mm for shield on busbars, contact resistance < 1 mohm, VPE: 10 pieces Shielding terminal 5 mm for shield on busbars, contact resistance < 1 mohm, VPE: 10 pieces R911173286 R911173282
Bosch Rexroth AG Postfach 13 57 97803 Lohr, Germany Bgm.-Dr.-Nebel-Str. 2 97816 Lohr, Germany Tel. +49 9352 18-0 Fax +49 9352 18-8400 www.boschrexroth.com/electrics Local contact information can be found at: www.boschrexroth.com/adressen Bosch Rexroth AG 2012 Subject to modification. Printed in Germany The data specified above only serve to describe the product. As our products are constantly being further developed, no statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging.