D/N VANDAL RESISTANT ATR 700TVL VARI-FOCAL DOME CAMERA CMD6182X/6186X3.6 N/P D/N VANDAL RESISTANT ATR 700TVL VARI-FOCAL IR DOME CAMERA CMR6182X/6186X3.6 N/P INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. GRAPHIC SYMBOL EXPLANATION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
PART DESCRIPTION & DIMENSION 145.0 3 4 1 10.0 2 78.7 130.0 5 6 7 (CMD6182X/6186X3.6N/P) 145.0 10.0 78.7 130.0 5 6 7 (CMR6182X/6186X3.6N/P) Unit: mm 1 2 3 4 5 6 7 8 BOTTOM CHASSIS TOP COVER BOTTOM HOLE SIDE HOLE INNER COVER DOME COVER LENS HOLE PLUG 8
INSTALLATION 1. Please use the enclosed hexagon screw driver to untighten the 4 screws on the top cover (FIG.1). FIG.1 2. Using screw drive to untighten the 3 screws on the camera module (FIG.2 & FIG.3). Camera Module Camera Module FIG.2 (CMD6182X/6186X3.6N/P) FIG.3 (CMR6182X/6186X3.6N/P) 3. Fix the safety rope on the bottom chassis with screw driver (FIG.4). Put the provided screws (M3.0x25, wooden screw) through the holes marked as a, and fix the bottom chassis in the desired area (FIG.5 & FIG.6).
FIG.4 a 66mm 120 a a FIG.5 FIG.6 4. Firstly, put video cable and power cable through a pipe with 1/2" PT at one end (FIG.7), and then screw the pipe to the side hole or bottom hole (FIG.8, please make sure the connection between the pipe and the side hole or bottom hole is watertight.). NOTE: Pipe is not provided. FIG.7 FIG.8 5. Using the screw driver to screw camera module into bottom chassis (FIG.9 & FIG.10).
Camera Module Camera Module FIG.9 (CMD6182X/6186X3.6N/P) FIG.10 (CMR6182X/6186X3.6N/P) 6. Plug and fix the power cable to the jack or terminal block and plug the video cable to video output of the camera (FIG.11 & FIG.12). For the safety reason, when plug video cable to video output, please use the cable tubing to cover the bare part to avoid danger of electric shock or electric leakage (FIG.13). FIG.11 ( ) CMD6182X3.6N/P CMR6182X3.6N/P FIG.12 ( ) CMD6186X3.6N/P CMR6186X3.6N/P Video Output Video Cable FIG.13
7. Take down the inner cover from the camera module (FIG.14, CMD6182X/6186X3.6N/P), and then adjust the direction of the lens through the adjustable Pan/Tilt bracket and rotatable round bracket for Azimuth (FIG.15 & FIG.16). TILT AZIMUTH TILT AZIMUTH FIG.14 Press inward and pull down. (CMD6182X/6186X3.6N/P) FIG.15 PAN (CMD6182X/6186X3.6N/P) FIG.16 PAN (CMR6182X/6186X3.6N/P) 8. Adjust the lens on focus and zoom to form the optimal video image after that tighten the screws (FIG.17 & FIG.18). Then adjust the OSD menu to form the optimal image. Please refer to Page 8 ~ Page 10. OSD KEY OSD KEY ZOOM ZOOM FIG.17 FOCUS (CMD6182X/6186X3.6N/P) FIG.18 FOCUS (CMR6182X/6186X3.6N/P) 8-1. USER OSD SETTING Setting switches and Functions. A. (UP) : Press to move the cursor upwards or to select B. (LEFT) items. : Press to move the cursor to the left and to select or adjust the parameters of the selected item. The parameters changes each time this button is pressed. UP LEFT RIGHT SET DOWN
C. (RIGHT) : Press to move the cursor to the right and to select or adjust the parameters of the selected item. The parameters changes each time this button is pressed. D. (DOWN) : Press to move the cursor downwards or to select items. E. SET : Executes selections and displays a submenu for an item with the mark. 9. Put on the inner cover (FIG.19, CMD6182X/6186X3.6N/P). Adjust the position of the inner cover inside the dome cover, so that the opening of the inner cover align with the direction of the lens (FIG.20 & FIG.21, CMR6182X/6186X3.6N/P). FIG.19 FIG.20 FIG.21 Press and turn (CMD6182X/6186X3.6N/P) (CMR6182X/6186X3.6N/P) (CMR6182X/6186X3.6N/P) 10. Fix the safety rope on the top cover with screw driver (FIG.22). Replace the top cover and tighten the screws (FIG.23). FIG.22 FIG.23
Alternative Cabling positions 1. Untighten the hole plug on the bottom hole of the bottom chassis and screw it to the side hole. 2. Put the video cable and power cable through the bottom hole. Then connect them to video output and power input of the camera. Please refer to INSTALLATION Step 4 for water resistant installation.
CONFIGURATION OF THE MENU SETUP MENU LENS SHUTTER/ AGC WHITE BAL PICT ADJUST ATR AUTO MANUAL BACKLIGHT- BLC/ HLC/ ON TYPE-DC MODE- AUTO/ OPEN/ CLOSE SPEED(000~255) AUTO HIGH LUMINANCE MODE AUTO IRIS/ SHUT+AUTO IRIS SHUT(NOTES*2) (NOTES*1) BRIGHTNESS(000~255) LOW LUMINANCE MODE- AGC/ BRIGHTNESS- x0.25/ x0.50/ x0.75/ x1.00 MANUAL MODE-SHUT+AGC SHUTTER- 1/60(1/50) / 1/100(1/120) / 1/250~1/10000 AGC- 6.00/ 12.00/ 18.00/ 24.00/ 30.00/ 36.00/ 42.00/ 44.80 ATW SPEED(000~255) DELAY CNT(000~255) ATW FRAME- x0.50/ x1.00/ x1.50/ x2.00 ENVIRONMENT- INDOOR/ OUTDOOR PUSH USER 1 B-GAIN(000~255) R-GAIN(000~255) USER 2 B-GAIN(000~255) R-GAIN(000~255) ANTI CR MANUAL-LEVEL(000~255) PUSH LOCK MIRROR-/ ON BRIGHTNESS(000~255) CONTRAST(000~255) SHARPNESS(000~255) HUE(000~255) GAIN(000~255) LUMINANCE- LOW/ MID/ HIGH CONTRAST- LOW/ MIDLOW/ MID/ MIDHIGH/ HIGH
PRIVACY ON NR NR MODE- Y/C/ / Y/ C Y LEVEL(000~015) C LEVEL(000~015) CAMERA ID SYNC-INT ON AREA SEL-1/8~8/8 TOP [000~244(NTSC), 000~288(PAL)] BOTTOM [000~244(NTSC), 000~288(PAL)] LEFT [000~474(NTSC), 000~468(PAL)] RIGHT [000~474(NTSC), 000~468(PAL)] COLOR(1~8) TRANSP- 0.00/ 0.50/ 0.75/ 1.00 MOSAIC- / ON ^ ^ LANGUAGE- ENGLISH/ / DEUTSCH/ FRANCAIS/ PYCCK / PORTUGUES/ ~ ESPANOL/ CAMERA RESET NN NOTES *1: Set the LENS mode to AUTO on the SETUP MENU menu. *2: Set the LENS mode to MANUAL on the SETUP MENU menu.
SETTING MENU AND FUNCTION TO Open and Exit the Menu screen 1. Press "SET" button. The Menu screen appears on the monitor. Check the current settings on the menu. 2. Push or button to select the options then use or button to select a mode. NEXT: To the next setup menu. BACK: Return to the previous. RETURN: Return to the previous. SAVE ALL: Used to save the various setting of the internal OSD menu in the EEPROM together. EXIT: Exit the setup menu. SETUP MENU SETUP MENU LENS SHUTTER/AGC WHITE BAL BACKLIGHT PICT ADJUST ATR PRIVACY AUTO AUTO ATW BLC NR CAMERA ID SYNC LANGUAGE CAMERA RESET INT ENGLISH NEXT EXIT SAVE ALL BACK EXIT SAVE ALL Setting of shutter speed of AUTO IRIS mode Please set-up proper shutter speed for AUTO IRIS mode as below: SHUTTER/AGC: AUTO[SETUP MENU] SET MODE: AUTO IRIS[AUTO SETUP] RETURN SHUTTER/AGC: MANUAL[SETUP MENU] SET SHUTTER:1/60(1/50) or 1/100(1/120) or 1/250...[MANUAL SETUP] RETURN SHUTTER/AGC: AUTO[SETUP MENU] SAVE ALL SET EXIT NOTES 1. Only DC mode on the TYPE option. Because a DC auto iris lens is used with the vari-focal lens camera. 2. Please select AUTO mode on the SHUTTER/AGC option. If you select MANUAL mode, the over exposure may occur.
SPECIFICATIONS Model No. Lens Power Input Voltage System Pick Up Element Effective Pixels Chip Size Horizontal & Vertical Sync. Frequency Scanning System Menu Control Sync. Mode Infrared Cut Filter Resolution Minimum Illumination S/N Ratio Auto Gain Control White Balance Shutter Adaptive Tone Reproduction Back Light Compensation Noise Reduction Picture Adjust Privacy Masking Privacy Masking Zone OSD Language Video Output Gamma Characteristic Power Consumption Operating Temperature IP Rating Vandal Proof Focal Length Iris Angle of view D/N VANDAL RESISTANT ATR 700TVL VARI-FOCAL DOME CAMERA Auto Manual H V Color Mono Luminance Contrast D CMD6182X3.6N/P DC12V ( ± 10%) 3.3 ~ 12mm F1.4 89.8 ~ 23.9 63.6 ~ 17.9 125.7 ~ 29.9 NTSC or PAL 1/3" Exview HAD CCD Sensor 976(H) x 494(V) [NTSC] 976(H) x 582(V) [PAL] 5.58mm(H) x 4.67mm(V) 15.734 KHz / 59.94Hz [NTSC] 15.625 KHz / 50Hz [PAL] 2:1 Interlace OSD Control Internal Auto Selectable, Automatic Switch From Color Mode to Monochrome Color: 700TV Lines, Mono: 750TV Lines 0.045Lux / F1.4 0.009Lux / F1.4 More Then 50dB (AGC-) AUTO / MANUAL ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK 1/60(1/50)S ~ 1/100,000S 1/60(1/50)S, 1/100(1/120)S, 1/250S, 1/500S, 1/1,000S, 1/2,000S, 1/4,000S, 1/10,000S LOW / MID / HIGH LOW / MIDLOW / MID / MIDHIGH / HIGH BLC / HLC(High Light Compensation) / Y / C / Y/C / MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN ON / 8 Zones ENGLISH/JAPANESE/GERMANS/FRENCH/RUSSIAN/PORTUGUESE/SPANISH/SIMPLY CHINESE 2.3W CVBS 1.0Vp-p, 75ohm γ=0.45-10 ~ +50 (14 ~ 122 ) IP67 3.5W (DC12V) 3.0W (AC24V) Withstand a blow from a 10 lbs sledgehammer Dimension ψ145(d) x 130mm(H) Weight 970g Design and specifications are subject to change without notice. CMD6186X3.6N/P DC12V ( ± 10%) AC24V ( ±10% ) 990g
Model No. Lens Power Input Voltage System Pick Up Element Effective Pixels Chip Size Horizontal & Vertical Sync. Frequency Scanning System Menu Control Sync. Mode Infrared Cut Filter Resolution Minimum Illumination S/N Ratio Auto Gain Control White Balance Shutter Adaptive Tone Reproduction Back Light Compensation Noise Reduction Picture Adjust Privacy Masking Privacy Masking Zone OSD Language Video Output Gamma Characteristic Power Consumption Operating Temperature IP Rating Vandal Proof Infrared LED Focal Length Iris D/N VANDAL RESISTANT ATR 700TVL VARI-FOCAL IR DOME CAMERA Angle of view Auto Manual Peak Wavelength Beam Spread H V Color Mono Luminance Contrast D IR On Radiant Distance CMR6182X3.6N/P DC12V ( ± 10%) NTSC or PAL 1/3" Exview HAD CCD Sensor 976(H) x 494(V) [NTSC] 976(H) x 582(V) [PAL] 5.58mm(H) x 4.67mm(V) 15.734 KHz / 59.94Hz [NTSC] 15.625 KHz / 50Hz [PAL] 2:1 Interlace OSD Control Internal Auto Selectable, Automatic Switch From Color Mode to Monochrome Color: 700TV Lines, Mono: 750TV Lines 0.045Lux / F1.4 0.009Lux / F1.4 0Lux More Then 50dB (AGC-) AUTO / MANUAL ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK 1/60(1/50)S ~ 1/100,000S 1/60(1/50)S, 1/100(1/120)S, 1/250S, 1/500S, 1/1,000S, 1/2,000S, 1/4,000S, 1/10,000S LOW / MID / HIGH LOW / MIDLOW / MID / MIDHIGH / HIGH BLC / HLC(High Light Compensation) / Y / C / Y/C / MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN ON / 8 Zones ENGLISH/JAPANESE/GERMANS/FRENCH/RUSSIAN/PORTUGUESE/SPANISH/SIMPLY CHINESE 6.1W 3.3 ~ 12mm F1.4 89.8 ~ 23.9 63.6 ~ 17.9 125.7 ~ 29.9 CVBS 1.0Vp-p, 75ohm γ=0.45-10 ~ +50 (14 ~ 122 ) IP67 8.8W (DC12V) 7.0W (AC24V) Withstand a blow from a 10 lbs sledgehammer 850nm Dimension ψ145(d) x 130mm(H) Weight 1000g Design and specifications are subject to change without notice. 30 25M CMR6186X3.6N/P DC12V ( ± 10%) AC24V ( ±10% ) 1020g 66-CMR618CSE-2
MERIT LILIN ENT. CO., LTD http://www.meritlilin.com 66-CMR618CSE