System Suggestion www.silva.se
NX2 Race The FDX, Fast Data exchange, is the protocol that allows the PC to become a fully integrated NX2 instrument when connected to the NX2 Server. The NX2 Race software free of charge with all NX2 FDX Servers, so bring your PC onboard and use all capabilities that the NX2 system can offer! The NX2 Race software enables you to monitor all data in analogue or digital format, create waypoints and routes, logging all data, calibrate the transducers and system setup. You can also activate the NX2 Steer Pilot, set backlight levels on the instruments etc. In short - control the whole NX2 system. The latest NX2 Race software can also be downloaded on the web for use with Silva NX2 FDX server based systems. The NX2 Race software will not work with NMEA0183 protocol. Connect your PC direct to the NX2 FDX Server PC port that normally is operating in NMEA0183 mode. When the NX2 Race software is started, the Server will automatically switch over to FDX mode to be fully integrated with the NX2 system.
NX2 General Every unit/instrument with the name NX2 can be connected to the network. You can configure the system in pretty much which way you want with up to 32 NX2 units connected to the network. The Server must be a part of the system. FDX Server: Steer Pilot Analog Wind Speed Trim Compass Is the brain of the NX2 system. To the Server you will connect all transducers you want information from, instruments in which you want to see the information and all other non NX2 units, e.g. a PC, you want to have in the system. The Server must be used together with the Multi Control and/or Remote Control. Shows you the difference from a set reference angle. E.g. The compass course, bearing to waypoint, course to steer etc. Steer Pilot must be controlled from the Multi Control and/or the Remote Control. It can also be set from a push button. Shows you the wind angle. True or apparent Presents speed changes in per cent since last trimming. Presents current course.
Multi Control: Multi XL: Wind Data GPS Navigator Compass Data Is an instrument that is able to present all information (two lines of information at the same time) available in the NX2 network. This instrument can also control all the information in the Server e.g. settings and calibrations. It also has the feature to be used as a remote control for other instruments. Works basically as the Multi Control. The difference is that it has larger digits. Multi XL must be controlled from the Multi Control and/or the remote control. Digital wind display. Shows both TWA & AWA at the same time. Can also present TWS, AWS, BSP among other things. TBS can be presented if a PC is connected to the server. Shows current position, SOG, COG and other satellite based information. Also has the ability to enter and edit waypoints, routes and sailplans in the instrument. A digital compass display that shows the boats current course both in numbers and graphic. Has the ability to use BTW, CTS and wind as steer reference. Speed Star Sea Data Remote Control CF Mast Bracket Presents BSP, distance, maximum BSP, average BSP and timer with countdown function. It can be a standalone instrument. Is a standalone instrument which can present log, depth and distance values. Works basically as a Multi Control instruments. Can present all data in the network and used for autopilot steering. Fitting for Multi XL instruments on the mast.
NX2 TRANSDUCERS. NX2 AUTOPILOT. LOG TRANSDUCER WIND TRANSDUCERS. GPS ANTENNA 52mm THF DEPTH TRANSDUCER COMPASS TRANSDUCERS. NX2 Autopilot consists, for boats up to app. 45 feet, of 5 parts. For boats above app. 45 feet the integrated drive unit, HP40, will be split in to two parts; a separate ram and a separate pump. Servo unit: Connection box and brain for the autopilot system. Integrated hydraulic drive unit: The unit that affects the rudder to move when the autopilot is engaged. Will be mounted a tiller arm attached to the rudder stock or the quadrant. Rudder angle transmitter: Important to give the autopilot as accurate rudder information as possible. Compass transducer: Gives the autopilot information about the actual course which will be compared to the set reference course. The compass transducer shall be connected to the Servo unit. If the autopilot system is integrated with the NX2 system i.e. with the Server, the compass transducer can be connected to either the Server or the Servo. Instrument that can control the autopilot: From the instrument you will activate/deactivate the autopilot. This instrument can be: - NX2 Autopilot instrument - NX2 Remote Control SERVO
Instrument placering Raceutförande: Med log, lod, vind, kompass och GPS Mast Ratt pedistalen 2X Multi Control 3X Multi XL 1X Steer Pilot Navstation (PC Tillbehör) Multi Control GPS Navigator
Detaljerad Specification Raceutförande: Med log, lod, vind, kompass och GPS Mast Ratt pedistalen Tillbehör 3X Multi XL Steer Pilot 2X Multi Control VHF S10 Nav station GPS Navigator Multi Control Mast fäste Q: Product name: Part no. Q: Product name: Part no.: Product name: Part no.: 1 Multi Control 22118-31 incl. Server 1 Log givare 20707 1 Lod givare 22409 1 Kompass givare 45º 20860 1 GPS Nav+Antenn 22118-6 1 Vind givare. Race 22511 3 Multi XL 21680-1 1 Mastfäste Kolfibr. 69995-4 1 Styr Pilot 22115-02 2 Multi Control 22117-3 VHF S10 28011