CB-6204/8 Bullet Camera CM-6204/8 Mini-Dome Camera CM-6206 Hemispheric Camera Release Notes Firmware Version 20160805 Ver. 1 August 12, 2016
2016 FLIR Systems, Inc. All rights reserved worldwide. No parts of this document, in whole or in part, may be copied, photocopied, translated, or transmitted to any electronic medium or machine readable form without the prior written permission of FLIR Systems, Inc. Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR Systems, Inc. and/or its subsidiaries. All other trademarks, trade names, or company names referenced herein are used for identification only and are the property of their respective owners. This product is protected by patents, design patents, patents pending, or design patents pending. The contents of this document are subject to change. FLIR Systems, Inc. 6769 Hollister Avenue Goleta, California 93117 USA Phone: 888.747.FLIR (888.747.3547) International: +1.805.964.9797 For technical assistance, please call us at +1.888.388.3577 or visit the Service & Support page at www.flir.com/security. Document History Version Date Comment 1 August 12, 2016 Initial FLIR release ii 20160805 Firmware Release Notes August 12, 2016
Table of Contents Table of Contents 1 Version Content... 1 1.1 Version Details... 1 1.2 Firmware and Software Update Location... 1 2 Supported Products and Platforms... 3 3 Features and Improvements... 7 3.1 Rebranding and New UI Look and Feel... 7 3.2 ONVIF Profile S and Profile G Conformance... 7 3.3 New Hemispheric Camera... 7 3.4 New Quad HD Mini-Dome Camera... 7 3.5 Enhanced Motion Detection Experience... 7 3.6 Bug Fixes and Web Enhancements... 7 3.7 Basic Certification for Milestone, Exacq, Avigilon, and Genetec VMS... 7 4 Limitations... 9 5 Upgrade Procedure... 12 Appendix... 15 A.1. Discovering and Configuring the Camera on DNA 2.1.2.4... 15 August 12, 2016 20160805 Firmware Release Notes iii
August 9, 2016 20160805 Firmware Release Notes iv
Version Content 1 Version Content This release supports the key features listed in section 3 for the following cameras: CB-6204-11-I CB-6204-21-I CB-6208-11-I CB-6208-21-I CM-6204-11-I CM-6204-21-I CM-6204-10-I-RO CM-6204-11-I-RO CM-6208-11-I CM-6208-21-I CM-6206-H1-I In addition to documenting the Features and Improvements, these release notes cover Supported Products and Platforms, Limitations, Known Issues, and Upgrade Procedure. 1.1 Version Details Full version details: camera firmware version 20160805. 1.2 Firmware and Software Update Location The firmware and software updates are available from the FLIR web site or by email from product.enterprise.support@flir.com. August 12, 2016 20160805 Firmware Release Notes 1
2 20160805 Firmware Release Notes August 12, 2016
Supported Products and Platforms 2 Supported Products and Platforms This firmware is supported with the following software versions: Product Name CB-6204-11-I CB-6204-21-I CB-6208-11-I CB-6208-21-I CM-6204-11-I Description IP Mini-Bullet Camera, including 3MP,1/3 sensor, F1.4, 3-8mm, Varifocal Motorized auto-focus, P-Iris lens with 96-38 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports three streams: Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). IP Mini-Bullet Camera, including 3MP,1/3 sensor, F1.4, 7-22mm, Varifocal Motorized auto-focus, P-Iris lens with 42-14 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports three streams: Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). IP Mini-Bullet Camera, including 12MP (4072 x 3076), 1/1.7 sensor, F1.4, 3.5-8mm Varifocal Motorized auto-focus, P-Iris lens with 116-50 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports four streams: UHD 4K, Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). IP Mini-Bullet Camera, including 12MP (4072 x 3076), 1/1.7 sensor, F1.4, 9-22mm Varifocal Motorized auto-focus, P-Iris lens with 45-18 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports four streams: UHD 4K, Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). IP Mini-Dome Camera, including 3MP,1/3 sensor, F1.4, 3-8mm motorized varifocal lens, Varifocal Motorized autofocus, P-Iris lens with 96-38 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports three streams: Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). August 12, 2016 20160805 Firmware Release Notes 3
Supported Products and Platforms Product Name CM-6204-21-I CM-6204-10-I-RO CM-6204-11-I-RO CM-6208-11-I CM-6208-21-I CM-6206-H1-I Description IP Mini-Dome Camera, including 3MP,1/3 sensor, F1.4, 7-22mm motorized varifocal lens, Varifocal Motorized autofocus, P-Iris lens with 42-14 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports three streams: Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). IP Mini-Dome Camera, including 3MP,1/3 sensor, F1.4, 3-8mm, Varifocal Motorized auto-focus, P-Iris lens with 96-38 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports three streams: QHD, Full HD 1080p, and HD 720p or D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). For indoor use and retrofitting inside Quasar Gen I enclosure. IP Mini-Dome Camera, including 3MP,1/3 sensor, F1.4, 3-8mm, Varifocal Motorized auto-focus, P-Iris lens with 96-38 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports three streams: QHD, Full HD 1080p, and HD 720p or D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). For indoor/outdoor use and retrofitting inside Quasar Gen I enclosure. IP Mini-Bullet Camera, including 12MP (4072 x 3076), 1/1.7 sensor, F1.4, 3.5-8mm Varifocal Motorized auto-focus, P-Iris lens with 116-50 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports four streams: UHD 4K, Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). IP Mini-Bullet Camera, including 12MP (4072 x 3076), 1/1.7 sensor, F1.4, 9-22mm Varifocal Motorized auto-focus, P-Iris lens with 45-18 horizontal viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports four streams: UHD 4K, Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). IP Hemispheric ( Fisheye ) Camera, including 6MP (3072 x 2048), 1/1.8 sensor, F2.8, 1.05mm Hemispheric lens with 180 viewing angle, audio line in, alarm in, True Day/Night, and infrared IR illuminator. The camera supports four streams: UHD 4K, Full HD 1080p, HD 720p, and D1 with H.264 or MJPEG compression. Powered by 12VDC, 24VAC, or 802.3af Power over Ethernet (PoE). For indoor/outdoor use 4 20160805 Firmware Release Notes August 12, 2016
Supported Products and Platforms Product Name United VMS 7.0 LU 5710 Latitude 6.3 CP1 LU 4148 United VMS 6.4 LU 6830 DNA 2.1.2.4 Description Latitude/Horizon/Meridian update 7.0.0.5710 and above. Installing the update patch is mandatory. Using patch 5757 is highly recommended Latitude 6.3 Camera Pack 1 with update 6.3.0.4148 and above. Installing the update patch is mandatory. Latitude/Horizon/Meridian 6.4 with update 4.0.6830 and above. Installing the update patch is mandatory. Discovery Network Assistant (DNA) version 2.1.2.4 or later. Note: 1. To discover the camera in Latitude/Horizon/Meridian, use the DVTEL Quasar Gen II option. 2. The camera s web UI is supported on Internet Explorer versions 10 and 11. August 12, 2016 20160805 Firmware Release Notes 5
6 20160805 Firmware Release Notes August 12, 2016
Features and Improvements 3 Features and Improvements 3.1 Rebranding and New UI Look and Feel cameras have been rebranded as FLIR models and feature a new user interface. 3.2 ONVIF Profile S and Profile G Conformance The current release conforms with the ONVIF 2.0 Profile S and Profile G, as tested with the ONVIF 16.01 test tool. 3.3 New Hemispheric Camera The FLIR CM-6206-H1-I camera is an indoor/outdoor, vandal-proof, IP hemispheric camera. The camera supports edge dewarping and software dewarping. 3.4 New Quad HD Mini-Dome Camera The FLIR CM-6204-11-I-RO camera is an indoor/outdoor, vandal-proof, IP mini-dome camera whose body is designed to be retrofitted inside the enclosure of a deployed Quasar Gen I CM-3211 or CM-4221 camera. The Quad HD camera now also supports 1080p resolution as a primary stream, in addition to the existing options. 3.5 Enhanced Motion Detection Experience Enhanced motion detection settings ( cell-based ) supported in Latitude s AdminCenter. It is available in Latitude 7.0.0.5757 and above. 3.6 Bug Fixes and Web Enhancements The current version includes various bug fixes and enhancements in the web interface. These include setting the default audio encoding to ulaw and the default Shutter WDR to Off. 3.7 Basic Certification for Milestone, Exacq, Avigilon, and Genetec VMS The current version has received basic certification for Milestone, Exacq, Avigilon, and Genetec Video Management Systems. August 12, 2016 20160805 Firmware Release Notes 7
8 20160805 Firmware Release Notes August 12, 2016
Limitations 4 Limitations BUG ID SUMMARY COMMENTS 42844 Audio-out doesn t work when the camera is set to multicast. The CM-6206-H1-I only supports rotation to 0 and 180 degrees while set to resolution 3072x2048. The CM-6206-H1-I can only be set to 6MP (3072x2048) when attached to Latitude in Software dewarping mode. The full experience of the enhanced motion detection ( cellbased ) is available on Latitude 7.0.0.5757 onward. Users of Latitude versions lower than 7.0.0.5757 may encounter that, after upgrading to the new firmware, motion detection may stop working. 42555 42908 Users of Latitude versions lower than 7.0.0.5757 may encounter that, when attaching a default camera to Latitude and setting Motion detection from AdminCenter, there are no detections. When a CM-6206-H1-I camera is attached to Latitude, it s automatically set on Software dewarping, using a single 6MP video stream. Software dewarping is only supported on this configuration in Latitude. On the CM-6206-H1-I camera in Latitude, the privacy mask moves on Control center and it does not cover its target well when zooming in. In Latitude, the camera s information on AdminCenter is not being refreshed on some cases, such as after firmware upgrade. Re-enable the Motion detection on the camera s web interface. Re-enable the Motion detection on the camera s web interface. Draw the zone on the Motion detection page in the camera s web interface. Use the Privacy mask that can be set from the camera s web interface. Manually re-discover the camera in AdminCetner. August 12, 2016 20160805 Firmware Release Notes 9
10 20160805 Firmware Release Notes August 12, 2016
5 Upgrade Procedure Use the Discovery Network Assistant (DNA) tool or the camera s web page to upgrade from previous firmware. Refer to the Appendix for details how to use DNA to discover cameras. To upgrade the camera firmware through DNA 1. Upon discovery of the unit(s), select the relevant unit(s) from the Discovery list. 2. Click the Firmware icon on the navigation bar. 3. Select the camera firmware file from the relevant fields on DNA. The upgrade file is named uimage_userland_all_20160805. 4. Click the Upgrade button. To upgrade the camera firmware through the camera s web page 1. Select the System tab on the navigation bar. 2. Select the Maintenance > Software Upgrade tab on the sidebar. 3. Follow the steps indicated on the screen to perform the upgrade. 4. In Step 2, change the option to uimage_userland.img 5. Click the Upgrade button 12 20160805 Firmware Release Notes August 12, 2016
14 20160805 Firmware Release Notes August 12, 2016
Appendix Appendix A.1. Discovering and Configuring the Camera on DNA 2.1.2.4 To operate DNA, copy the DNA.exe file to a folder on a PC and then double-click it. DNA is required to discover the cameras, because the camera initializes by default with a DHCP configuration. If a DHCP server is not available in your network, the camera will initialize with the default static IP 192.168.0.250. If you have more than one camera, connect them one at a time and change their IP addresses to avoid potential network conflicts. Refer to the DNA 2.1 User Manual for additional information on working with edge devices. August 12, 2016 20160805 Firmware Release Notes 15
FLIR Systems, Inc. 6769 Hollister Ave Goleta, CA 93117 USA PH: +1 805.964.9797 PH: +1 877.773.3547 (Sales) PH: +1 888.388-3577 (Support) FX: +1 805.685.2711 http://www.flir.com/security Corporate Headquarters FLIR Systems, Inc. 27700 SW Parkway Ave. Wilsonville, OR 97070 USA PH: +1 503.498.3547 FX: +1 503.498.3153 Document: Firmware 20160805 Release Notes Version: 1 Date: August 12, 2016 Language: en-us