Introduction Electronic Circuit Protection ESX0-T Electronic circuit protection type ESX0-T is designed to ensure selective disconnection of 24VDC load systems. 24VDC power supplies, which are widely used in industry today, will shut down the output in the event of an overload with the result that one faulty load in the system can lead to complete disconnection of all loads. Through selective disconnection the ESX0-T responds much faster to overload or short circuit conditions than the switch-mode power supply. This is achieved by active current limitation. The ESX0-T limits the highest possible current to.3 to.8 times the selected rated current of the circuit protector. Thus it is possible to switch on capacitive loads of up to 20,000 μf, but they are disconnected only in the event of an overload or short circuit. For optimal alignment with the characteristics of the application the current rating of the ESX0-T can be selected in fixed values from 0.5 A...2 A. Failure and status indication are provided by a multicolour LED and an integral shortcircuit-proof status output or a relay signal contact. Remote operation is possible by means of a remote reset signal or a remote ON/OFF control signal. The manual ON/OFF button allows separate actuation and reset of individual load circuits. Upon detection of overload or short circuit in the load circuit, the MOSFET of the load output will be blocked to interrupt the current flow. The load circuit can be re-activated via the remote electronic reset input, control input or manually by means of the ON/OFF button. Features Selective load protection, electronic trip characteristics Active current limitation for safe connection of capacitive loads up to 20,000 μf and on overload/short circuit ratings 0.5 A...2 A Reliable overload disconnection with. x In plus, even with long load lines or small cable cross sections (see table 3) Manual ON/OFF button (S) Control input IN+ for remote ON/OFF signal (option) Electronic reset input RE (option) Clear status and failure indication through LED, status output SF or Si contact F Integral fail-safe element adjusted to current rating Width per unit only 2.5 mm Rail mounting Ease of wiring through busbar and 0 V as well as signal bars and bridges UL/CSA Hazardous area approved Class, Div 2 42
Electronic Circuit Protection ESX0-T Approvals Authority Voltage rating ratings UL2367 (E306740) 24VDC 0.5...2 A UL604 (E322549) 24VDC 0.5...2 A (class, div. 2, group A, B, C, D) UL508/ cul 508 24VDC 0.5...2 A CSA file 6597: CSA C22.2 No: 23 (class I, div. 2) 24VDC 0.5...2 A Groups A, B, C, D, T5 CSA C22.2 No: 42 24VDC 0.5...2 A Class 2 Meets requirements for Class 2 current limitation (ESX0-T... 0.5 A / A / 2 A / 3 A Technical data (Tambient = 40 C, operating voltage Ub = 24VDC) Operating data Operating voltage Ub 24VDC (8...32 V) rating In fixed current ratings: 0.5, A, 2 A, 3 A, 4 A, Closed current I0 Status indication by means of Load circuit Load output Overload disconnection 6 A, 8 A, 0 A, 2 A ON condition: typically 20...30 ma depending on signal output multicolour LED: GREEN: unit is ON, power-mosfet is switched on - status output SF ON, supplies + 24VDC ORANGE: in the event of overload or short circuit until electronic disconnection RED: - unit electronically disconnected - load circuit/power-mosfet OFF OFF: - manually switched off (S = OFF) or device is dead - undervoltage (Ub < 8 V) - after switch-on till the end of the delay period status output SF (option) potential-free signal contact F (option) ON/OFF/ condition of switch S Power-MOSFET switching output (high side switch) typically. x In (.05...35 x In) Short-circuit current IK active current limitation (see table ) Trip time see time/current characteristics for electronic disconnection typically 3 s at I Load >. x In typically 3 s...00 ms at I Load >.8 x In (or.5 x In/.3 x In) Temperature disconnection internal temperature monitoring with electronic disconnection Low voltage monitoring load output with hysteresis, no reset required load OFF at Ub < 8 V Starting delay t start typically 0.5 sec after every switch-on and after applying Ub Disconnection of load circuit electronic disconnection Free-wheeling circuit external free-wheeling diode recommended with inductive load Several load outputs must not be connected in parallel Technical data (Tambient = 40 C, operating voltage Ub = 24VDC) Status output SF Electrical data Status OUT OFF condition Signal output F Electrical data ON condition LED green OFF condition LED off Fault condition LED orange Fault condition LED red ESX0-TB-0 ESX0-TB-02 Fault Reset input RE Electrical data Reset signal RE (terminal 22) Control input IN+ Electrical data Control signal IN+ (terminal 2) Switch S ON/OFF ESX0-TB-4/-24/ plus-switching signal output, connects Ub to terminal 2 of module 7plus nominal data: 24VDC / max. 0.2 A (short circuit proof) status output is internally connected to GND with a 0 kohm resistor ESX0-TB-4/-24 (signal status OUT), at Ub = +24 V +24 V = S is ON, load output connected through 0V = S is ON, load output blocked and/or switch S is OFF red LED lit 0 V level at status output when: switch S is in ON position, but device is still in switch-on delay switch S is OFF, or control signal OFF, device is switched off no operating voltage Ub ESX0-TB-0/-02 potential-free signal contact max. 30VDC/0.5 A, min. 0 V/0 ma voltage Ub applied, switch S is in ON position no overload, no short circuit device switched off (switch S is in OFF position) no voltage Ub applied overload condition >. x In up to electronic disconnection electronic disconnection upon overload or short circuit device switched off with control signal (switch S is in ON position) single signal, make contact contact SC/SO-SI open single signal, break contact contact SC/SO-SI closed signal output fault conditions: no operating voltage Ub ON/OFF switch S is in OFF position red LED lighted (electronic disconnection) ESX0-TB-24 voltage: max. +32VDC high > 8VDC 32VDC low 3VDC > 0 V power consumption typically 2.6 ma (+24VDC) min. pulse duration typically 0 ms The electronically blocked ESX0-TB-24 may remotely be reset via an external momentary switch due to the falling edge of a +24 V pulse. A common reset signal can be applied to several devices simultaneously. Switched on devices remain unaffected. ESX0-TB-4 see reset input RE +24V level (HIGH): device will be switched on by a remote ON/OFF signal 0 V level (LOW): device will be switched off by a remote ON/OFF signal unit can only be switched on with S if a HIGH level is applied to IN+ 43
Electronic Circuit Protection ESX0-T Technical data (Tambient = 40 C, operating voltage Ub = 24VDC) General data Fail-safe element: backup fuse for ESX0-T not required because of the integral redundant fail-safe element Terminals / LOAD+ / 0V screw terminals M4 max. cable cross section flexible with wire end ferrule w/wo plastic sleeve 20-6 AWG (0.5-0 mm 2 ) multi-lead connection (2 identical cables) rigid/flexible 20- AWG (0.5-4 mm 2 ) flexible with wire end ferrule without plastic sleeve 20-3 AWG (0.5-2.5 mm 2 ) flexible with TWIN wire end ferrule with plastic sleeve 20-9 AWG (0.5-6 mm 2 ) wire stripping length 0 mm tightening torque (EN 60934).2 Nm Terminals aux. contacts screw terminals M3 max. cable cross section flexible with wire end ferrule w/wo plastic sleeve 23-3 AWG (0.25 2.5 mm 2 ) wire stripping length 8 mm tightening torque (EN 60934) 0.5 Nm Housing material moulded Mounting symmetrical rail to EN 50022-35x7.5 Ambient temperature 0...+50 C (without condensation, see EN 60204-) Storage temperature -20...+70 C Humidity Vibration 96 hrs/95 % RH/40 C to IEC 60068-2-78-Cab climate class 3K3 to EN 6072 3 g, test to IEC 68-2-6 test Fc Degree of protection housing: IP20 DIN 40050 terminals: IP20 DIN 40050 EMC emission: EN 6000-6-3 (EMC directive, CE logo) susceptibility: EN 6000-6-2 Insulation co-ordination 0.5 kv/2 pollution degree 2 (IEC 60934) dielectric strength Insulation resistance (OFF condition) re-inforced insulation in operating area max. 32VDC (load circuit) n/a, only electronic disconnection Approvals UL2367, File E306740, Dimensions (W x H x D) Mass Solid State Overcurrent Protectors UL604 (class I, div. 2, zone 2), UL508, CE logo CSA C22.2 No. 42 - file 6597, C22.2 No. 23 - file 6597, CD2 Groups A, B, C, D, Temp Code T5; Ambient 0-40 C 2.5 x 80 x 83 mm approx. 65 g Table : voltage drop, current limitation, max. load current current rating typically voltage drop active current max. load current at 00% ON duty In Uon at In limitation (typically) Tu = 40 C Tu = 50 C 0.5 A 70 mv.8 x In 0.5 A 0.5 A A 80 mv.8 x In A A 2 A 30 mv.8 x In 2 A 2 A 3 A 80 mv.8 x In 3 A 3 A 4 A 00 mv.8 x In 4 A 4 A 6 A 30 mv.8 x In 6 A 5 A 8 A 20 mv.5 x In 8 A 7 A 0 A 50 mv.5 x In 0 A 9 A 2 A 80 mv.3 x In 2 A 0.8 A Attention: when mounted side-by-side without convection the ESX0-T should not carry more than 80% of its rated load with 00% ON duty due to thermal effects. Please note: The user should ensure that the cable cross sections of the relevant load circuit are suitable for the current rating of the ESX0-T used. Automatic start-up of machinery after shut down must be prevented (Machinery Directive 98/37/EG and EN 60204-). In the event of a short circuit or overload the load circuit will be disconnected electronically by the ESX0-T. Refer to UL/CSA file for proper wiring and installation techniques. Table 2: ESX0-T - Ordering Information Version Signal input Signal output Signal contact Status output without Control input Remote without single signal single signal without Status OUT Status OUT Signal ON/OFF Reset Reset Signal N/O N/C Signal Positive 24V ØV = OK Input Output (normally open NO) (normally closed NC) Output = OK ESX0-TA-00 x x x ESX0-TB-0 x x x ESX0-TB-02 x x x ESX0-TB-4 x x ESX0-TB-24 x x x ESX0-TB-27 x x x ESX0-TA-00 Circuit Rating Protection (amps) Part Number 0.5 6720005305 672000530 2 6720005302 3 6720005303 4 6720005304 6 6720005306 8 6720005308 0 672000530 2 672000532 ESX0-TB-0 N/O Rating Contact (amps) Part Number 0.5 6720005320 672000532 2 6720005322 3 6720005323 4 6720005324 6 6720005326 8 6720005328 0 6720005330 2 6720005332 ESX0-TB-02 N/C Rating Contact (amps) Part Number 0.5 6720005340 672000534 2 6720005342 3 6720005343 4 6720005344 6 6720005346 8 6720005348 0 6720005350 2 6720005352 ESX0-TB-4* Control Rating Input (amps) Part Number 0.5 6720005360 672000536 2 6720005362 3 6720005363 4 6720005364 6 6720005366 8 6720005368 0 6720005370 2 6720005372 ESX0-TB-24** Reset Rating Input (amps) Part Number 0.5 6720005380 672000538 2 6720005382 3 6720005383 4 6720005384 6 6720005386 8 6720005388 0 6720005390 2 6720005392 ESX0-TB-27 Reset Rating Input (amps) Part Number 0.5 6720005309 672000539 2 6720005329 3 6720005339 4 6720005349 6 6720005369 8 6720005389 0 6720005399 2 672000533 * Control force input on/off ** Reset input only to reset under fault conditions 44
Electronic Circuit Protection ESX0-T ESX0-T Signal inputs / outputs (wiring diagram) ESX0-TA-00 without signal input/output ESX0-TB-0 without signal input with signal output F (single signal, N/O) ESX0-TB-02 without signal input with signal output F (single signal, N/C) ESX0-TB-4 with control input IN+ (+24VDC) with status output SF (+24 V = load output ON) 4 2 SF 23 3 IN 2 2 LOAD+ 0V 3 0V 3 0V 3 0V 3 operating condition: 3-4 closed fault condition: 3-4 open operating condition: -2 open fault condition: -2 closed operating condition: SF +24 V = OK fault condition: SF 0 V ESX0-TB-24 with reset input RE (+24VDC ) with status output SF (+24 V = load output ON) ESX0-TB-27 with reset input RE (+DC 24 V ) with inverse status output SF (0 V = load output ON) Dimensions 83 2.5 3.27.492 LINE LINE SF 23 SF 23 RE 22 RE 22 80 3.5 LOAD LOAD 0V 3 operating condition: SF +24 V = O fault condition: SF 0 V 0V 3 operating condition: SF 0 V = OK fault condition: SF +24 V label 80 3.5 snap-on socket for symmetrical rail EN 50022-35x7.5 This is a metric design and millimeter dimensions take precedence ( mm ) inch 45
Electronic Circuit Protection ESX0-T Time/ characteristic curve (Ta = 25 C) trip time in seconds 0000 000 00 0 5 0. disconnection typically. x I n.8 x I n *) current limitation *) typically.8 x I n The trip time is typically 3 s in the range between. and.8 x In * ). Electronic current limitation occurs at typically.8 x In * ) which means that under all overload conditions (independent of the power supply and the resistance of the load circuit) the max. overload before disconnection will not exceed.8 x In * ) times the current rating. Trip time is between 00 ms and 3 sec (depending on overload or at short circuit). Without this current limitation a considerably higher overload current would flow in the event of an overload or short circuit. 0.0 0 2 3 4 5 IK...times rated current *) current limitation typically.8 x In times rated current at In = 0.5 A...6 A current limitation typically.5 x In times rated current at In = 8 A or 0 A current limitation typically.3 x In times rated current at In = 2 A Table 3: Reliable trip of ESX0-T Reliable trip of ESX0-T with different cable lengths and cross sections Resistivity of copper ρ 0 = Ub = DC 9.2 V (= 80 % of 24 V) 0.078 (Ohm x mm 2 ) / m ESX0-T-selected rating In (in A) 3 6 voltage drop of ESX0-T and tolerance of trip point (typically. x In =.05....35 x In) have been taken into account. e. g. trip current Iab =.25 x In (in A) 3.75 7.5 ESX0-T trips after 3 s Rmax in Ohm = (Ub / Iab) - 0.050 5.07 2.5 The ESX0-T reliably trips from 0 Ohm to max. circuitry resistance Rmax Cable cross section A in mm 2 0.4 0.25 0.34 0.5 0.75.5 cable length L in meter cable resistance in Ohm = (R0 x 2 x L) / A (= single length) 5.27 0.7 0.52 0.36 0.24 0.8 0.2 0 2.54.42.05 0.7 0.47 0.36 0.24 5 3.8 2.4.57.07 0.7 0.53 0.36 20 5.09 2.85 2.09.42 0.95 0.7 0.47 25 6.36 3.56 2.62.78.9 0.89 0.59 30 7.63 4.27 3.4 2.4.42.07 0.7 35 8.90 4.98 3.66 2.49.66.25 0.83 40 0.7 5.70 4.9 2.85.90.42 0.95 45.44 6.4 4.7 3.20 2.4.60.07 50 2.7 7.2 5.24 3.56 2.37.78.9 75 9.07 0.68 7.85 5.34 3.56 2.67.78 00 25.34 4.24 0.47 7.2 4.75 3.56 2.37 25 3.79 7.80 3.09 8.90 5.93 4.45 2.97 50 38.4 2.36 5.7 0.68 7.2 5.34 3.56 75 44.50 24.92 8.32 2.46 8.3 6.23 4.5 200 50.86 28.48 20.94 4.24 9.49 7.2 4.75 225 57.2 32.04 23.56 6.02 0.68 8.0 5.34 250 63.57 35.60 26.8 7.80.87 8.90 5.93 Example : max. length at.5 mm 2 and 3 A 24 m Example 2: max. length at.5 mm 2 and 6 A 06 m Example 3: mixed wiring: R = 40 m in.5 mm 2 and R2 = 5 m in 0.25 mm 2 : (Control cabinet sensor/actuator level) R = 0.95 Ohm, R2 = 0.7 Ohm Total (R + R2) =.66 Ohm 46
Electronic Circuit Protection ESX0-T Mounting examples for ESX0-T The ESX0-T features an integral power distribution system. busbar 672000535 continuous busbar 500 mm length, cut (2.5 x n)-3 = length of busbars ± 0.5 e. g. (2.5 x 5)-3 = 59.5 ± 0.5 Up to 40 pole signal bar 672000536 or jumper 672000537 (2 pole only) remove protection against brush contact located on bottom side side walls or barriers for protection against brush contact on and OV jumper locations 0V busbar 672000535 insert protection against brush contact insert busbars and protection slides to be flush with housing sides 2.5 x n = width of protector block e. g. 2.5 x 5 = 62.5 insert signal bars to be flush with housing and place them centrally over the contacts 5 ESX0-TB with busbars and jumpers 5 ESX0-TA with busbars Mounting procedure: Before wiring insert busbars into protection block. 47
Electronic Circuit Protection ESX0-T Connection diagrams and application examples ESX0-T Signal contacts are shown in OFF or fault concition. ESX0-TA-00 ESX0-TB-0 group signaling (series connection) + line entry terminals for busbars screw terminals + line entry + line entry for the SI busbar LINE + busbar +24V +24V 3 4 3 4 3 4 group signalling by means of an LED power supply DC 24 V ESX0-TA-00 ESX0-TA-00 ESX0-TA-00 power supply DC 24 V ESX0-TB-0 ESX0-TB-0 ESX0-TB-0 jumpers are staggered 0V 3 0V 3 0V 3 0V 0V 3 0V 3 0V 3 0V 0 V busbar 0 V busbar - line entry - line entry + - load + - load + - load + + + - - - load load load ESX0-TB-02 ESX0-TB-24 Single signaling with common line entry Single signaling with common reset + line entry for the SI single signalling per way by means of an LED reset button single signalling per way by means of an LED + line entry + line entry busbar busbar +24V +24V 2 2 2 22 RE SF 23 22 RE SF 23 22 RE SF 23 power supply DC 24 V ESX0-TB-02 ESX0-TB-02 ESX0-TB-02 signal busbar for common line entry power supply DC 24 V ESX0-TB-24 ESX0-TB-24 ESX0-TB-24 signal busbar for common reset 0 V 3 0V 3 0V 3 0V 0V 3 0V 3 0V 3 0V 0 V busbar 0 V busbar - line entry - line entry + - + - + - + - + - + - load load load load load load 48
Electronic Circuit Protection ESX0-T Accessories for ESX0-T Description The ESX0-T features an integral power distribution system. The following wiring modes are possible with various pluggable current and signal busbars: LINE +(24VDC) 0 V Caution: The electronic devices ESX0-T require a 0 V connection signal contacts reset inputs Description Part No. Busbars for and 0 V 672000535 max. load with one line entry Imax 50 A (recommended: centre line entry) max. load with two line entries Imax 63 A length: 500 mm Signal busbars for signal contacts and reset inputs 672000536 max. load with one line entry Imax A with one series connection of signal contacts Imax 0.5 A length: 500 mm Jumpers for signal contacts 672000537 length: packing unit: 2 mm 0 pcs TS32 rail adapter 90200000 (Remove protection walls/barriers before using adapter.) For detailed installation instructions and approvals contact Weidmuller at -800-849-9343 or go to www.weidmuller.com 49
Introduction Circuit Protection Weidmuller s DIN-rail mounted circuit breakers are available for use in applications where circuit protection must be able to distinguish between circuit overloads and short circuits. Each circuit breaker has the ability to be reset without the need to change components. All circuit breakers are available with an assortment of jumpers and marking tags. Circuit breakers in the 9926 Series are culus listed according to UL489 and CSA 22.2 No. 5.02, CE, VDE. The hydraulic magnetic trip mechanism offers 0,000A of interrupting capacity in 20V and 240V, 50/60Hz applications. The CB2200 Series feature integrated alarm contacts within a narrow profile, thereby allowing increased enclosure capacity. All of these circuit breakers demonstrate consistent reliability through 00% calibration and testing, and feature a touch safe design to prevent injury from accidental contact with live components. CB2200 Series The CB4200 Series of thermal magnetic circuit breakers feature a pushbutton style of trip reset. This reset provides a visual indication of status which allows for rapid troubleshooting. CB4200 Series The CB900 Series of thermal magnetic circuit breakers provide a rugged and industry-standard form factor (8 mm/pole). For supplemental circuit protection. CB900 Series 50
Branch Rated Circuit Breakers AC Version Circuit Breakers Hydraulic Magnetic Type Single Pole Double Pole Single pole and double pole versions 20/240 VAC, 50/60 Hz Up to 25A Just 3 mm wide Mounts on 35mm DIN-rail culus listed according to UL489 CSA C22.2 No. 5.02, CE, VDE Ordering Data Type: Single Pole (up to 20 VAC) Type: Double Pole (up to 240 VAC) Part No. Part No. (amps) TS 35 Description (amps) TS 35 Description 0.5 992625000 QL--3-DM-KM-0.5 0.5 9926252000 QL-2-3-DM-KM-0.5 99262500 QL--3-DM-KM-0 992625200 QL-2-3-DM-KM-0 2 992625002 QL--3-DM-KM-02 2 9926252002 QL-2-3-DM-KM-02 3 992625003 QL--3-DM-KM-03 3 9926252003 QL-2-3-DM-KM-03 4 992625004 QL--3-DM-KM-04 4 9926252004 QL-2-3-DM-KM-04 5 992625005 QL--3-DM-KM-05 5 9926252005 QL-2-3-DM-KM-05 6 992625006 QL--3-DM-KM-06 6 9926252006 QL-2-3-DM-KM-06 7 992625007 QL--3-DM-KM-07 7 9926252007 QL-2-3-DM-KM-07 8 992625008 QL--3-DM-KM-08 8 9926252008 QL-2-3-DM-KM-08 0 99262500 QL--3-DM-KM-0 0 992625200 QL-2-3-DM-KM-0 3 99262503 QL--3-DM-KM-3 3 992625203 QL-2-3-DM-KM-3 5 99262505 QL--3-DM-KM-5 5 992625205 QL-2-3-DM-KM-5 6 99262506 QL--3-DM-KM-6 6 992625206 QL-2-3-DM-KM-6 20 992625020 QL--3-DM-KM-20 20 9926252020 QL-2-3-DM-KM-20 25 992625025 QL--3-DM-KM-25 25 9926252025 QL-2-3-DM-KM-25 Technical Data Voltage 20/240 VAC, 50/60Hz minimum 0.5A maximum 25A Interrupting capacity 0,000A Dielectric strength 500V, 50/60Hz Insulation resistance 00MM Operating life 0000 mechanical operations Operating temperature -40 +65 C Wire size* 0.5-5A: 4AWG min., 0AWG max. 20-25A: 0AWG min. Torque 20 in.-lb Approval culus listed according to UL489 CSA C22.2 No. 5.02, CE, VDE Accessories Part No. Bus-bar ( pole, insulated, m) 670904 Bus-bar (2 pole, insulated, m) 670972 Bus-bar end cap, pole 670973 Bus-bar end cap, 2 pole 670974 Power lug, straight 670960 Power lug, 90 67096 Lock-out handle 67093 *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit). The SchS2 accepts DEK, WS and ESG 8/7 marking tags. The part number for adhesive SchS2 is 720600000. Trip Curves Hydraulic Magnetic Type Typical time/current characteristics at 30ºC Sample trip characteristics - KM 25% 50% 200% 400% 600% 800% 000% minimum 5 8 4 0.7 0.09 0.007 0.005 (sec) maximum 300 90 28 4.5 0.6 0.4 (sec) Although the 9926 series uses a magnetic only trip mechanism, CSA testing indicates a trip characteristic similar to thermal magnetic trip mechanisms. No de-rating is required at elevated temperatures. Additional trip curves and amp ratings are available upon request. AC Version - dimensions in mm (in.) 7.4 (2.8) 28.5 (.2) 5 (0.2) 9 (0.75) 74 (2.9) 66 (2.6) 32 (.26) 45 (.77) 64.8 (2.55) AC version Trip Curve Tripping Time 000 0 0 0. Seconds Minutes00 0.0 0.00 00 05 30 50 200 300 7.9 (0.7) 57 (2.24) 3 (0.5) Operating Characteristics Curve Ambient Temperature 30 C 400 500 000 500 (%) Rated 2000 2500 3000 92.8 (3.65) 4000 5000 Trip Curve applies to the following part numbers where "XX" is the current rating: Single Pole 9926252XX Double Pole 99262522XX AC version Trip Curve Tripping Time 26 (.02) 3 (0.5) 000 0 0 0. Seconds Minutes00 0.0 0.00 00 05 25 50 200 300 Operating Characteristics Curve KM Ambient Temperature 30 C 400 500 000 500 (%) Rated 2000 2500 3000 4000 5000 5
Branch Rated Circuit Breakers AC Version with Contacts Circuit Breakers with Auxiliary switch, Trip alarm, Combination of both Single Pole w/ Auxiliary Contact Single Pole Trip (Alarm Contact) Single Pole Combination (Auxiliary & Alarm Contact) AC voltages (20/240V) Single and double pole versions culus listed according to UL489 and C22.2 No. 5.02, CE, VDE Factory fitted auxiliary or trip alarm Compact 6.5mm width Attached to right hand side of circuit breaker Technical Data Voltage 20/240 VAC, 50/60Hz minimum 0.5A maximum 25A Interrupting capacity 0,000A Dielectric strength 500V, 50/60Hz Insulation resistance 00MM Operating life 0000 mechanical operations Operating temperature -40 +65 C Wire size* 0.5-5A: 4AWG min., 0AWG max. 20-25A: 0AWG min. Torque 20 in.-lb Approval culus listed according to UL489 and C22.2 No. 5.02, CE, VDE Type: Single Pole Aux (up to 20 VAC) 99262600 QL-A--3-DM-KM- 2 992626002 QL-A--3-DM-KM-2 5 992626005 QL-A--3-DM-KM-5 0 99262600 QL-A--3-DM-KM-0 5 99262605 QL-A--3-DM-KM-5 20 992626020 QL-A--3-DM-KM-20 25 992626025 QL-A--3-DM-KM-25 Double Pole w/ Auxiliary Contact Type: Single Pole Trip (up to 20 VAC) 99262700 QL-T--3-DM-KM- 2 992627002 QL-T--3-DM-KM-2 5 992627005 QL-T--3-DM-KM-5 0 99262700 QL-T--3-DM-KM-0 5 99262705 QL-T--3-DM-KM-5 20 992627020 QL-T--3-DM-KM-20 25 992627025 QL-T--3-DM-KM-25 Double Pole Trip (Alarm Contact) Type: Single Pole Combo (up to 20 VAC) 99262800 QL-AT--3-DM-KM- 2 992628002 QL-AT--3-DM-KM-2 5 992628005 QL-AT--3-DM-KM-5 0 99262800 QL-AT--3-DM-KM-0 5 99262805 QL-AT--3-DM-KM-5 20 992628020 QL-AT--3-DM-KM-20 25 992628025 QL-AT--3-DM-KM-25 Double Pole Combination (Auxiliary & Alarm Contact) UL 489 listed (5A, 250 VAC; 0.5A, 80 VDC Auxiliary; 0.5A, 25 VDC Trip Alarm) IEC 60947-5- Approved (5A, 250 VAC; 0.5A, 0 VDC Auxiliary; 0.5A, 25 VDC Trip Alarm) *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit). The SchS2 accepts DEK, WS and ESG 8/7 marking tags. The part number for adhesive SchS2 is 720600000. Type: Double Pole Aux (up to 240 VAC) 992626200 QL-A-2-3-DM-KM- 2 9926262002 QL-A-2-3-DM-KM-2 5 9926262005 QL-A-2-3-DM-KM-5 0 992626200 QL-A-2-3-DM-KM-0 5 992626205 QL-A-2-3-DM-KM-5 20 9926262020 QL-A-2-3-DM-KM-20 25 9926262025 QL-A-2-3-DM-KM-25 Type: Double Pole Trip (up to 240 VAC) 992627200 QL-T-2-3-DM-KM- 2 9926272002 QL-T-2-3-DM-KM-2 5 9926272005 QL-T-2-3-DM-KM-5 0 992627200 QL-T-2-3-DM-KM-0 5 992627205 QL-T-2-3-DM-KM-5 20 9926272020 QL-T-2-3-DM-KM-20 25 9926272025 QL-T-2-3-DM-KM-25 Type: Double Pole Combo (up to 240 VAC) 992628200 QL-AT-2-3-DM-KM- 2 9926282002 QL-AT-2-3-DM-KM-2 5 9926282005 QL-AT-2-3-DM-KM-5 0 992628200 QL-AT-2-3-DM-KM-0 5 992628205 QL-AT-2-3-DM-KM-5 20 9926282020 QL-AT-2-3-DM-KM-20 25 9926282025 QL-AT-2-3-DM-KM-25 AC version Trip Curve Dual Mount Dimensions in mm (in.) Trip Curves Hydraulic Magnetic Type Typical time/current characteristics at 30ºC Additional trip curves and amp ratings are available upon request. Tripping Time 000 0 0 0. 0.0 0.00 Seconds Minutes00 Operating Characteristics Curve KM Ambient Temperature 30 C 57.0 (2.24) 26.2 (.03) (N/O)6 (N/C)8 (C)5 3.3 (.23) (C) 2(N/C) 4(N/O) 2.3 (0.84) 32.9 (.3) 2. (0.83) 0.7 (0.42) TRIP ALARM Q. CONNECTORS 00 05 25 50 200 300 400 500 000 500 2000 2500 3000 4000 5000 2 (0.08) 0.5 (0.02) 5.5 (0.22) AUX SWITCH Q. CONNECTORS 2.8 (0.) 0.5 (0.02) 7 (0.28) (%) Rated 52
Branch Rated Circuit Breakers DC Version Circuit Breakers Hydraulic Magnetic Type Single pole versions only U2 trip curve for general purpose applications 80 and 25 VDC Up to 60A Just 3 mm wide Mounts on 35mm DIN-rail UL 489A listed VDE Single Pole (80 VDC) Single Pole (25 VDC) Ordering Data Type: Single Pole (80 VDC) 0.5 992625900 QY--3-DM-U2-0.5 99262590 QY--3-DM-U2-0 2 992625902 QY--3-DM-U2-02 3 992625903 QY--3-DM-U2-03 4 992625904 QY--3-DM-U2-04 5 992625905 QY--3-DM-U2-05 0 99262590 QY--3-DM-U2-0 5 99262595 QY--3-DM-U2-5 20 992625920 QY--3-DM-U2-20 25 992625925 QY--3-DM-U2-25 30 992625930 QY--3-DM-U2-30 35 992625935 QY--3-DM-U2-35 40 992625940 QY--3-DM-U2-40 45 992625945 QY--3-DM-U2-45 50 992625950 QY--3-DM-U2-50 60 992625960 QY--3-DM-U2-60 Type: Single Pole (25 VDC) 99262580 QY--3-DM-U2-0-B 2 992625802 QY--3-DM-U2-02-B 3 992625803 QY--3-DM-U2-03-B 4 992625804 QY--3-DM-U2-04-B 5 992625805 QY--3-DM-U2-05-B 0 99262580 QY--3-DM-U2-0-B 5 99262585 QY--3-DM-U2-5-B 20 992625820 QY--3-DM-U2-20-B 25 992625825 QY--3-DM-U2-25-B 30 992625830 QY--3-DM-U2-30-B 35 992625835 QY--3-DM-U2-35-B 40 992625840 QY--3-DM-U2-40-B 45 992625845 QY--3-DM-U2-45-B 50 992625850 QY--3-DM-U2-50-B 60 992625860 QY--3-DM-U2-60-B Accessories DC version Trip Curve Dimensions in mm (in.) Type Part No. Bus-bar ( pole, insulated m) 670904 Bus bar end cap, pole 670973 Power lug, straight 670960 Power lug, 90 67096 Lock-out handle 67093 Trip Curves Hydraulic Magnetic Type Typical time/current characteristics at 30ºC Additional trip curves and amp ratings are available upon request. 74 (2.9) 66 (2.6) 7.9 (0.7) 3 (0.5) Technical Data Voltage 80,25 VDC minimum 0.5 A maximum 60 A Interrupting capacity 0,000 A Dielectric strength 500 V, 50/60 Hz Insulation resistance 00 MM Operating life 0000 mechanical operations Operating temperature -40 +65 C Wire size* -5A: 4 AWG min., 0 AWG max. 20-25A: 0 AWG min. Torque 20 in.-lb Approval UL 489A Listed, CE, VDE Tripping Time 000 0 0 0. 0.0 0.00 Seconds Minutes00 00 05 30 50 200 300 Operating Characteristics Curve U2 DC (4% Ripple Factor) Ambient Temperature 30 C 400 500 (%) Rated 000 500 2000 2500 3000 4000 5000 7.4 (2.8) 28.5 (.2) 5 (0.2) 9 (0.75) 32 (.26) 45 (.77) 64.8 (2.55) 57 (2.24) 92.8 (3.65) *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit). The SchS2 accepts DEK, WS and ESG 8/7 marking tags. The part number for adhesive SchS2 is 720600000. 53
Supplemental Circuit Breakers Circuit Breakers Hydraulic Magnetic Type Single Pole Double Pole Triple Pole AC Voltages 277/480V Trip curve 2 for general purpose applications UL 077 recognized VDE approved and CE marked Just 3 mm wide Mounts to 35 mm DIN-rail Factory fitted auxiliary or trip alarm Single, double and triple pole versions Ordering Data Accessories Type: Single Pole (up to 277 VAC) Type: Double Pole (up to 480 VAC) Type: Triple Pole (up to 480 VAC) Rating Rating 99262550 QZ--3-D-2-0 992625250 QZ-2-3-D-2-0 0 992625350 QZ-3-3-D-2-0 2 992625502 QZ--3-D-2-02 2 9926252502 QZ-2-3-D-2-02 5 992625355 QZ-3-3-D-2-5 3 992625503 QZ--3-D-2-03 4 9926252504 QZ-2-3-D-2-04 20 9926253520 QZ-3-3-D-2-20 4 992625504 QZ--3-D-2-04 5 9926252505 QZ-2-3-D-2-05 25 9926253525 QZ-3-3-D-2-25 5 992625505 QZ--3-D-2-05 6 9926252506 QZ-2-3-D-2-06 30 9926253530 QZ-3-3-D-2-30 6 992625506 QZ--3-D-2-06 0 992625250 QZ-2-3-D-2-0 40 9926253540 QZ-3-3-D-2-40 8 992625508 QZ--3-D-2-08 5 992625255 QZ-2-3-D-2-5 50 9926253550 QZ-3-3-D-2-50 0 99262550 QZ--3-D-2-0 20 9926252520 QZ-2-3-D-2-20 60 9926253560 QZ-3-3-D-2-60 5 99262555 QZ--3-D-2-5 25 9926252525 QZ-2-3-D-2-25 20 992625520 QZ--3-D-2-20 30 9926252530 QZ-2-3-D-2-30 25 992625525 QZ--3-D-2-25 35 9926252535 QZ-2-3-D-2-35 35 992625535 QZ--3-D-2-35 40 9926252540 QZ-2-3-D-2-40 40 992625540 QZ--3-D-2-40 50 9926252550 QZ-2-3-D-2-50 50 992625550 QZ--3-D-2-50 60 9926252560 QZ-2-3-D-2-60 60 992625560 QZ--3-D-2-60 Supplemental dimensions in mm (in.) Type Part No. Bus bar ( pole, insulated m) 670904 Bus bar (2 pole, insulated m) 670972 Bus bar (3 pole, insulated m) 67097 Bus bar end cap, pole 670973 Bus bar end cap, 2 pole or 3 pole 670974 Power lug, straight 670960 Power lug, 90 67096 Lock-out handle 67093 22.5 (0.86) 65 (2.56) 60 (2.36) 25.9 (0.94) 45 (.77) 3 (0.5) 92.8 (3.65) 26 (.02) 39 (.54) 44 (.73) 3 (0.5) 3 (0.5) 5.0 (0.2) 63.8 (2.5) 73 (2.87) Technical Data Supplemental Trip Curve Voltage minimum maximum Interrupting capacity Dielectric strength Insulation resistance Operating life Operating temperature Wire size* -5A: 20-25A: Torque 277/480 VAC @ 50/60 Hz 0.5 A 60 A 5 ka @ 277/480 V, 5 ka @ 20 V, 5 ka @ 240 V 500 V, 50/60 Hz 00 MM 0000 mechanical operations -40 +65 C 4 AWG min., 0 AWG max. 0 AWG min. Approval UL 077 Recognized, VDE (EN 60947-2) Approved, CSA C22.2 No. 235, CE Marked 20 in.-lb Trip Curves Hydraulic Magnetic Type Typical time/current characteristics at 30ºC Additional trip curves and amp ratings are available upon request. Tripping Time 000 0 0 0. Seconds Minutes00 0.0 Operating Characteristics Curve 2 Ambient Temperature 30 C *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit).the SchS2 accepts DEK, WS and ESG 8/7 marking tags. The part number for adhesive SchS2 is 720600000. 0.00 00 05 30 50 200 300 400 500 (%) Rated 000 500 2000 2500 3000 4000 5000 curus recognized to UL077 and C22.2 No. 235 54
Supplemental Circuit Breakers with Contacts Circuit Breakers Auxiliary switch, Trip alarm, Combination of both Single Pole w/ Auxiliary Contact Single Pole Trip (Alarm Contact) Single Pole Combination (Auxiliary & Alarm Contact) AC Voltages 277/480V Trip curve 2 for general purpose applications UL 077 recognized VDE approved and CE marked Just 3 mm wide Mounts to 35 mm DIN-rail Factory fitted auxiliary or trip alarm Single, double and triple pole versions Technical Data Voltage 277/480 VAC @ 50/60 Hz minimum 0.5 A maximum 60 A Interrupting capacity 5 ka @ 277/480 V, 5 ka @ 20 V, 5 ka @ 240 V Dielectric strength 500 V, 50/60 Hz Insulation resistance 00 MM Operating life 0000 mechanical operations Operating temperature -40 +65 C Wire size* -5A: 4 AWG min., 0 AWG max. 20-25A: 0 AWG min. Torque 20 in.-lb Approval UL 077 Recognized, VDE (EN 60947-2) Type: Single Pole Aux (up to 277 VAC) 99262650 QZ-A--3-D-2-0 2 992626502 QZ-A--3-D-2-02 5 992626505 QZ-A--3-D-2-05 0 99262650 QZ-A--3-D-2-0 5 99262655 QZ-A--3-D-2-5 20 992626520 QZ-A--3-D-2-20 25 992626525 QZ-A--3-D-2-25 Double Pole w/ Auxiliary Contact Type: Single Pole Trip (up to 277 VAC) 99262750 QZ-T--3-D-2-0 2 992627502 QZ-T--3-D-2-02 5 992627505 QZ-T--3-D-2-05 0 99262750 QZ-T--3-D-2-0 5 99262755 QZ-T--3-D-2-5 20 992627520 QZ-T--3-D-2-20 25 992627525 QZ-T--3-D-2-25 Double Pole Trip (Alarm Contact) Type: Single Pole Combo (up to 277 VAC) 99262850 QZ-AT--3-D-2-0 2 992628502 QZ-AT--3-D-2-02 5 992628505 QZ-AT--3-D-2-05 0 99262850 QZ-AT--3-D-2-0 5 99262855 QZ-AT--3-D-2-5 20 992628520 QZ-AT--3-D-2-20 25 992628525 QZ-AT--3-D-2-25 Double Pole Combination (Auxiliary & Alarm Contact) Approved, CSA C22.2 No. 235, CE Marked UL 489 listed (5A, 250 VAC; 0.5A, 80 VDC Auxiliary; 0.5A, 25 VDC Trip Alarm) IEC 60947-5- Approved (5A, 250 VAC; 0.5A, 0 VDC Auxiliary; 0.5A, 25 VDC Trip Alarm) *Wire sizes: gauges specified are the minimum allowable as per CSA and UL standards. The 9926 circuit breakers do not have provisions for marking tags. A possible solution is to cut the adhesive SchS2 tag rail to length (approximately 20 mm on a single pole unit so the current rating remains visible or approximately 30 mm on a two pole unit). The SchS2 accepts DEK, WS and ESG 8/7 marking tags.the part number for adhesive SchS2 is 720600000. Supplemental Trip Curve Trip Curves Hydraulic Magnetic Type Typical time/current characteristics at 30ºC 000 Operating Characteristics Curve 2 Type: Double Pole Aux (up to 480 VAC) 992626250 QZ-A-2-3-D-2-0 2 9926262502 QZ-A-2-3-D-2-02 5 9926262505 QZ-A-2-3-D-2-05 0 992626250 QZ-A-2-3-D-2-0 5 992626255 QZ-A-2-3-D-2-5 20 9926262520 QZ-A-2-3-D-2-20 25 9926262525 QZ-A-2-3-D-2-25 Triple Pole w/ Auxiliary Contact Type: Double Pole Trip (up to 480 VAC) 992627250 QZ-T-2-3-D-2-0 2 9926272502 QZ-T-2-3-D-2-02 5 9926272505 QZ-T-2-3-D-2-05 0 992627250 QZ-T-2-3-D-2-0 5 992627255 QZ-T-2-3-D-2-5 20 9926272520 QZ-T-2-3-D-2-20 25 9926272525 QZ-T-2-3-D-2-25 Triple Pole Trip ( Alarm Contact) Type: Double Pole Combo (up to 480 VAC) 992628250 QZ-AT-2-3-D-2-0 2 9926282502 QZ-AT-2-3-D-2-02 5 9926282505 QZ-AT-2-3-D-2-05 0 992628250 QZ-AT-2-3-D-2-0 5 992628255 QZ-AT-2-3-D-2-5 20 9926282520 QZ-AT-2-3-D-2-20 25 9926282525 QZ-AT-2-3-D-2-25 Triple Pole Combination (Auxiliary & Alarm Contact) Tripping Time 0 0 0. Seconds Minutes00 0.0 0.00 00 05 30 50 200 300 400 500 Ambient Temperature 30 C (%) Rated 000 500 2000 2500 3000 4000 5000 curus recognized to UL077 and C22.2 No. 235 Type: Triple Pole Aux (up to 480 VAC) 992626350 QZ-A-3-3-D-2-0 2 9926263502 QZ-A-3-3-D-2-02 5 9926263505 QZ-A-3-3-D-2-05 0 992626350 QZ-A-3-3-D-2-0 5 992626355 QZ-A-3-3-D-2-5 20 9926263520 QZ-A-3-3-D-2-20 25 9926263525 QZ-A-3-3-D-2-25 Type: Triple Pole Trip (up to 480 VAC) 992627350 QZ-T-3-3-D-2-0 2 9926273502 QZ-T-3-3-D-2-02 5 9926273505 QZ-T-3-3-D-2-05 0 992627350 QZ-T-3-3-D-2-0 5 992627355 QZ-T-3-3-D-2-5 20 9926273520 QZ-T-3-3-D-2-20 25 9926273525 QZ-T-3-3-D-2-25 Type: Triple Pole Combo (up to 480 VAC) 992628350 QZ-AT-3-3-D-2-0 2 9926283502 QZ-AT-3-3-D-2-02 5 9926283505 QZ-AT-3-3-D-2-05 0 992628350 QZ-AT-3-3-D-2-0 5 992628355 QZ-AT-3-3-D-2-5 20 9926283520 QZ-AT-3-3-D-2-20 25 9926283525 QZ-AT-3-3-D-2-25 55
Supplemental Circuit Breakers GFCI Ground Fault Interrupt CE approved UL077 and UL053 recognized Small frame size (26mm wide) Single pole plus switched neutral ground leakage protection Trip point is unaffected by ambient temperature ratings up to 50A Trip indication (mid trip handle position) Trip curve 2 for general purpose applications GFCI Ordering Data Type: Single Pole GFCI 5 99262905 QF7A2505 - CB W/GFI 0 9926290 QF7A250 - CB W/GFI 5 9926295 QF7A255 - CB W/GFI 20 99262920 QF7A2520 - CB W/GFI 25 99262925 QF7A2525 - CB W/GFI 30 99262930 QF7A2530 - CB W/GFI 50 99262950 QF7A2550 - CB W/GFI GFCI dimensions in mm (in.) 73 (2.87) 65 (2.56) Technical Data Standard Ampere (A) 5 to 50A Sensitivity (ma) 30 (CE) / 22 (UL) Number of Poles + N Equipment Type Ground Leakage/GFCS Rated Voltage (V) 230 (CE) / 240 (UL) Rated Interrupting/ 5 ka Withstand Capacity (ka) Weight (kg) 0.26 Trip Curve (standard) 2 Operating Temperature -40 to +65ºC Approval UL 077 and UL 053, CE AC version Trip Curve Trip Curves Hydraulic Magnetic Type Typical time/current characteristics at 30ºC Tripping Time 000 0 0 0. Seconds Minutes00 0.0 Operating Characteristics Curve 2 Ambient Temperature 30 C 93 (3.66) 82.4 (3.24) 26 (.02) 44 (.73) 68.8 (2.7) 7.8 (0.307) 57 (2.24) 6.4 (0.646) 8.0 (0.35) 0.00 00 05 30 50 200 300 400 500 000 500 2000 2500 3000 4000 5000 7.4 (2.8) 26 (.02) (%) Rated 35.7 (.406) 56
Mounting Options and Accessories Mounting Options If the product is not vertically mounted in the normal DIN-rail mounting orientation, a rating factor must be applied. Figure shows a diagram of the rating factor to apply. The published curves for these circuit breaker products are produced with the circuit breaker in the vertical mounting position. The rating factor only applies to the must hold and must trip points of the curve as the other parts (instantaneous trip point) stay largely unaffected. ON OFF 95% ON OFF 45 UP 93% HORIZ ON 45 UP OFF 95% ON OFF It is important to note that in environments that are exposed to a high degree of vibration, the cables that connect to the circuit breaker must be securely held in place, as the breaker is not designed to carry the weight of the cables. A maximum of 35N can be applied to the terminal area, in a direction perpendicular to the mounting axis. 00% OFF ON VERT DOWN 45 HORIZ DOWN 45 VERT OFF ON 00% 05% OFF ON OFF ON 05% Accessories 07% Technical Data Rating 80A max. Voltage 500V max. Short Circuit Strength 25kA Type Part No. Bus bar ( pole, insulated m) 670904 Bus bar (2 pole, insulated m) 670972 Bus bar (3 pole, insulated m) 67097 Type Part No. Bus bar end cap, pole 670973 Bus bar end cap, 2 pole or 3 pole 670974 Technical Data Rating 85A max. Wire Size 0 AWG min., 4 AWG max. Dimensions A: 6 mm B: 32 mm Type Part No. Power lug, straight 670960 Power lug, 90 67096 Type Part No. Lock-out handle 67093 Part Number Table - Example To order Single Pole Circuit Breaker Part No. 99262500 Rating of.0 amp Internal Resistance per Pole of. ohms Trip Curve M, Medium (Standard) 992625000 Amperage "00" - 0.5A "0" - A "02" - 2A / "60" - 60A 992624000 Amperage Trip Curves (Types 5-9) "0" - Branch AC KM (Standard) "" - Branch AC OP (Instantaneous) "2" - Branch AC (Fast) "3" - Supplemental 9 (Slow) "4" - Branch 80VDC (Fast) "5" - Supplemental 2 (Standard) "6" - Branch 25VDC OP (Instantaneous) "7" - Branch 80VDC OP (Instantaneous) "8" - Branch 25VDC U2 (Standard) "9" - Branch 80VDC U2 (Standard) Poles Pole 2 Pole 3 Pole Type "5" - Base Breaker "6" - With Auxiliary Contact "7" - With Trip Alarm Contact "8" - Combo Aux/Trip Contact "9" - GFCI "00" - 0.5A "0" - A "02" - 2A / "60" - 60A Trip Curves (Type 4) "0" - Supplemental (Slow) "" - Supplemental 3 (Fast) "3" - Branch AC 9 (Slow) Poles Pole 2 Pole 3 Pole Type "4" - Base Breaker 57
CB4200 Series Supplemental Circuit Breakers Circuit Breakers Thermal Magnetic Type CB4200 Series Single Pole CB4200 Series Double Pole Rated from 0.05 to 6.0 amps Available in single or double pole configurations Features a tease free design to reduce contact damage Offers push button trip/reset function Trip free design means the breaker cannot be held closed against a fault Mounts on 32mm* or 35mm DIN-rail UL 077 recognized CSA C22.2 No. 235 Ordering Data Type: Single Pole Type: Double Pole Part No. TS 35 Part No. TS 35 *For TS 32 Rail, *For TS 32 Rail, (amps) see adapter below (amps) see adapter below 0.05 924083500 0.05 924223500 Trip Curves Thermal Magnetic Type Typical time/current characteristics at 23ºC 0.08 924653500 0.08 924233500 0. 90473500 0. 920353500 0.2 90483500 0.2 924243500 0.3 92983500 0.3 924263500 0.4 924093500 0.4 924273500 0.5 90003500 0.5 929583500 0.6 9243500 0.6 924283500 0.7 929563500 0.7 924293500 0.8 9003500 0.8 929593500.0 90203500.0 92963500.2 90303500.2 929623500.3 92423500.3 92433500.4 92433500.4 924323500.5 90403500.5 929633500.8 92443500.8 924333500 2.0 90503500 2.0 929643500 2.5 90603500 2.5 929653500 3.0 90703500 3.0 929663500 3.5 92463500 3.5 924343500 4.0 904353500 4.0 92973500 4.5 92473500 4.5 924353500 5.0 90803500 5.0 929673500 5.5 907833500 5.5 924363500 6.0 90383500 6.0 924373500 6.5 920043500 6.5 924383500 7.0 90453500 7.0 924393500 8.0 903003500 8.0 904673500 9.0 90463500 9.0 924423500 0.0 90903500 0.0 929683500.0 92483500.0 924433500 2.0 907843500 2.0 924443500 3.0 92493500 3.0 924453500 4.0 907853500 4.0 924463500 5.0 902003500 5.0 929693500 6.0 92423500 6.0 924473500 CB4200 Series M+ 0.05 to 7.5 A M+ 8 to 6 A *Adapter foot dimensions in mm (in.) 0,000,000 30 C +23 C +55 C 0,000,000 30 C +23 C +55 C 00 00 20 (.787) Trip time in seconds 0 Trip time in seconds 0 90200000 TS32 adapter 0. 0. 0.0 0.0 0.00 0.8 2 3 4 6 8 0 20 30 50 70 00 times rated current 0.00 0.8 2 3 4 6 8 0 20 30 50 70 00 times rated current 58
CB4200 Series Supplemental Circuit Breakers CB4200 Series Single Pole CB4200 Series Double Pole Internal Wiring Diagram Internal Wiring Diagram Dimensions in mm Technical Data Rated voltage & current Creepage resistance Dielectric strength Insulation resistance Interrupting capacity (VDE 0660, Part 0, P-2) Interrupting capacity; 420 (UL 077/EN 60934 PC) UL CSA VDE Voltage AC 250 V, DC 65 V, 50/60 Hz 0.05 6 A AC 250 V, DC 65 V, 50/60 Hz 0.05 6 A AC 250 V, DC 65 V, 50/60 Hz 0.05 6 A PTI 600 to IEC 2 4,000 VAC; IEC 664 & 664 A > 00 MM (DC 500 V) 420-0 Maximum capacity 0.05 0.8 A Self-limiting 2 A 200 A 2.5 6 A 400 A Rated current Rated voltage Maximum capacity 0.05 2.0 A AC 250 V 200 A 2.0 6 A AC 250 V 200 A 20 A AC 25 V 400 A Dimensions in mm Typical life at 2 x rated current Shock Torque Vibration Temperature range Corrosion Humidity Weight Wire size (UL) 5,000 operations 25 g ( ms) to IEC 68-2-27, Test Ea.2 Nm 5 g (57 to 500 Hz / ±0.38 mm, 0 to 57 Hz) to IEC 68-2-6, Test Fc -30 C +55 C (-22 F +3 F) 96 hours at 5% salt spray, to IEC 68-2-, Test Ka 240 hours at 95% RH, to IEC 68-2-3, Test Ca 60 g per pole #20 8 AWG solid/0.5 6 mm 2 Accessories Jumpers Type Part No. Adapter foot (for TS 32 Rail) Busbar Busbar end cap for 6720000227 Power lug for 6720000227 Daisy Chain 50* Straight CQB** insulated Angled CQB** insulated Single pole meter BDC 50 9970290000 CQB 2 9970560000 CQB 3 9970570000 CQB 4 9970580000 CQB 0 9970590000 CQB 2 9970600000 CQB 3 997060000 CQB 4 9970620000 CQB 0 9970630000 MCBAF/TS 32 90200000 6720000227 6720000225 6720000226 Marking Tags Note: Part numbers are shown for a single card of pre-printed tags numbered -50. Special print only Consecutive horizontal Consecutive vertical WS 8/5 MC 640750000*** DEK 5/5 047346000 DEK 5/5 047356000 Note: Resistive and inductive loads (0.05-6 A) *BDC will accommodate 20 A per pin, 20 A total **CQB will accommodate 8 A per pin, 8 A total; dedicated to 420 Series ***Please specify horizontal or vertical print when ordering. Standard quantity = 44 tags per card. 59
CB2200 Series Supplemental Circuit Breakers Circuit Breakers Thermal Magnetic Type CB2200 Series Single Pole CB2200 Series Double Pole CB2200 Series Triple Pole Rated from 0. to 32.0 amps Available in single, double and triple pole configurations Offers normally open (N/O) and normally closed (N/C) auxiliary contacts Lever-switch trip/reset function Mounts on 32mm or 35mm DIN-rail UL 077 recognized CSA C22.2 No. 235 Ordering Data Type: Single Pole* Type: Double Pole Type: Triple Pole N/O Aux. N/O-N/C N/O-N/C (amps) Part No. (amps) Part No. (amps) Part No. 0. 9900005 0. 99200003 0. 99300003 0.2 99020005 0.2 992020003 0.2 993020003 0.3 99030005 0.3 992030003 0.3 993030003 0.4 99040005 0.4 992040003 0.4 993040003 0.5 99050005 0.5 992050003 0.5 993050003 0.6 99060005 0.6 992060003 0.6 993060003 0.8 99080005 0.8 992080003 0.8 993080003.0 9900005.0 99200003.0 99300003.5 9950005.5 99250003.5 99350003 2.0 99200005 2.0 992200003 2.0 993200003 2.5 99250005 2.5 992250003 2.5 993250003 3.0 99300005 3.0 992300003 3.0 993300003 4.0 99400005 4.0 992400003 4.0 993400003 5.0 99500005 5.0 992500003 5.0 993500003 6.0 99600005 6.0 992600003 6.0 993600003 8.0 99800005 8.0 992800003 8.0 993800003 0 99200005 0 992200003 0 992300003 2 99220005 2 992220003 2 992320003 5 99250005 5 992250003 5 992350003 6 99260005 6 992260003 6 992360003 8 99280005 8 992280003 8 992380003 20 992200005 20 9922200003 20 9923200003 25 992250005 32 992320005 *All part numbers with N/O Auxiliary Contacts on each pole when the main breaker contact is open (in the OFF position) Ordering Data Type: Single Pole Type: Double Pole Type: Triple Pole All part numbers with N/C Auxiliary Contacts on each pole when the main breaker contact is open (in the OFF position) (amps) Part No. (amps) Part No. (amps) Part No. 0. 9900000 0. 99200000 0. 99300000 0.2 99020000 0.2 992020000 0.2 993020000 0.3 99030000 0.3 992030000 0.3 993030000 0.4 99040000 0.4 992040000 0.4 993040000 0.5 99050000 0.5 992050000 0.5 993050000 0.6 99060000 0.6 992060000 0.6 993060000 0.8 99080000 0.8 992080000 0.8 993080000.0 9900000.0 99200000.0 99300000.5 9950000.5 99250000.5 99350000 2.0 99200000 2.0 992200000 2.0 993200000 2.5 99250000 2.5 992250000 2.5 993250000 3.0 99300000 3.0 992300000 3.0 993300000 4.0 99400000 4.0 992400000 4.0 993400000 5.0 99500000 5.0 992500000 5.0 993500000 6.0 99600000 6.0 992600000 6.0 993600000 8.0 99800000 8.0 992800000 8.0 993800000 0 99200000 0 992200000 0 992300000 2 99220000 2 992220000 2 992320000 5 99250000 5 992250000 5 992350000 6 99260000 6 992260000 6 992360000 8 99280000 8 992280000 8 992380000 20 992200000 20 9922200000 20 9923200000 25 992250000 25 9922250000 25 9923250000 32 992320000 32 9922320000 32 9923320000 60
T CB2200 Series Supplemental Circuit Breakers CB2200 Series Trip Curves Thermal Magnetic Type Typical time/current characteristics at 23ºC CB2200 Series 0,000,000 F 0. to 32 A 30 C +23 C +55 C Trip time in seconds 00 0 0. 0.0 0.00.8 2 3 4 6 80 20 30 50 70 00 times rated current -M 0. to 7.5 A 0,000,000 30 C AC +23 C DC +23 C +55 C 00 Dimensions in mm Technical Data Rated voltage & current UL Voltage 277 / 480 VAC (50/60 Hz); 65 VDC 0. 32 A Trip time in seconds 0 0. 0 DC CSA 277 / 480 VAC (50/60 Hz); 65 VDC 0. 32 A 0.0 AC VDE 250 / 45 VAC / 65 VDC 0. 32 A Auxiliary contacts 250 VAC / 65 VDC, A 0.00.8 2 3 4 6 80 20 30 50 70 00 times rated current Creepage resistance PTI 600 to IEC 2 Dielectric strength Insulation resistance Interrupting capacity (VDE 0660, Part 0, P-2) 3,000 VAC; IEC 664 & 664 A > 00 MM (DC 500 V) Rated current Rated voltage Rupture capacity (3 times) 0.05 0.8 A 250 / 45 VAC 400 A 0,000,000 -M 8 to 32 A 30 C AC +23 C DC +23 C +55 C 6 32 A 250 / 45 VAC 800 A 00 Interrupting capacity (UL 077/EN 60934 PC) Rated current Rated voltage Max. rupture capacity (3 times) 0. 6 A 277 / 480 VAC 5000 A 20 32 A 277 / 480 VAC 2000 A Trip time in seconds 0 0. 32 A 65 VDC 2000 A 0. DC Typical life at 2 x rated current Shock Torque Vibration Temperature range Corrosion Humidity Weight Wire size (UL) Nm (lb. in.) Accessories Jumpers Daisy Chain 50 Busbars 5,000 operations 25 g ( ms) to IEC 68-2-27, Test Ea 0.6 (5.3) Auxiliary contact: 0.5 (4.4) 5 g (57 to 500 Hz / ±0.38 mm, 0 to 57 Hz) to IEC 68-2-6, Test Fc -30 +60 C (-22 F +40 F) 96 hours at 5% salt spray, to IEC 68-2-, Test Ka 240 hours at 95% RH, to IEC 68-2-3, Test Ca Approximately 60 g per pole max 6 mm 2 8 AWG max.5 mm 2 4 AWG (Aux. contact) Type Part No. BDC 50, 20 A maximum 9970290000 pole (CB2200) 998650000 2 pole (CB2200) 9987360000 Trip time in seconds 0.0 0,000,000 00 0 0. AC 0.00.8 2 3 4 6 80 20 30 50 70 00 times rated current -T 0. to 7.5 A 30 C +23 C +55 C 0.0 Marking Tags 2 3 4 5 6 Note: Part numbers shown are for a single card of pre-printed tags numbered -50. Special print only Consecutive horizontal Consecutive vertical DEK 5/6 0490360000* DEK 5/6 046866000 DEK 5/6 046876000 0.00.8 2 3 4 6 80 20 30 50 70 00 times rated current -T 8 to 32 A Note: Resistive and inductive loads (0.05-6 A) *Please specify horizontal or vertical print when ordering. 0,000,000 30 C +23 C +55 C Trip time in seconds 00 0 0. 0.0 0.00.8 2 3 4 6 80 20 30 50 70 00 times rated current 6
CB900 Series Supplemental Circuit Breakers Circuit Breakers Thermal Magnetic Type CB900 Series Single Pole CB900 Series Double Pole CB900 Series Triple Pole Rated from 0.5 to 63 amps Available in single, double and triple pole configurations Optional auxiliary contacts Mounts on 35mm DIN-rail UL and CSA approvals CSA 277 VAC ( pole) or 480 VAC (2 and 3 pole) 50 VDC (0.5 A to 50 A) pole 0 VDC (0.5 A to 50 A) 2 pole Ordering Data Type: Single Pole Type: Double Pole Type: Triple Pole (amps) Part No. (amps) Part No. (amps) Part No. 0.5 9925350000 0.5 9925650000 0.5 992580000.0 9925360000.0 9925660000.0 9925820000 2.0 9925380000 2.0 9925680000 2.0 9925840000 3.0 9925390000 3.0 9925690000 3.0 9925850000 4.0 9925400000 4.0 9925700000 4.0 9925860000 6.0 992540000 6.0 992570000 6.0 9925870000 0.0 9925430000 0.0 9925730000 0.0 9925890000 3.0 9929820000 3.0 9929830000 3.0 9929840000 6 9925440000 6 9925740000 6 9925900000 20 9925450000 20 9925750000 20 992590000 25 9925460000 25 9925760000 25 9925920000 32 9925470000 32 9925770000 32 9925930000 40 9925480000 40 9925780000 40 9925940000 50 9925490000 50 9925790000 50 9925950000 63 9925500000 63 9925800000 63 9925960000 Trip Curves Thermal Magnetic Type Typical time/current characteristics at 23 C CB900 Series M 0.5 to 6 A M AC 0 to 40 A M AC 63 A 0,000 0,000 0,000 23 C 23 C 23 C,000,000,000 00 00 00 Trip time in seconds 0 Trip time in seconds 0 Trip time in seconds 0 0. 0. 0. 0.0 0.0 0.0 0.00 0.8 2 3 4 6 8 0 20 30 50 70 00 times rated current 0.00 0.8 2 3 4 6 8 0 20 30 50 70 00 times rated current 0.00 0.8 2 3 4 6 8 0 20 30 50 70 00 times rated current 62
CB900 Series Supplemental Circuit Breakers CB900 Series 45 59 pole 36 8 6 44 70 2 pole 3 pole 54 86 Dimensions in mm Internal Wiring Diagram Technical Data Rated voltage & current UL 077 CSA C 22.2 No. 235 VDE Creepage resistance Insulation resistance Interrupting capacity (UL 077/EN 609334 PC) pole Mechanical/Electrical endurance Shock Torque Vibration Temperature range - operating Weight Strip length Auxiliary contact rating Wire size - #22 2 AWG Wire size 277 V ( pole) 480 V (2 and 3 pole) 50 VDC ( pole) 0 VDC (2 pole) 277 V ( pole) 480 V (2 and 3 pole) 50 VDC ( pole) 0 VDC (2 pole) PTI 250 to IEC 2 >00 MM at 500 VDC ratings Interrupting Rupture capacity (3X) Voltage 0.5...63 A 0,000 A (UL) 277 VAC/50 VDC 0.5...32 A 2,000 A (UL) 277 / 480 AC 0.5...63 A 6,000 A (UL) 50 VDC () pole 0.5...50 A 6,000 A (UL) 0 VDC (2) poles 20,000/0,000 20 g (0 ms) 2 Nm 3 g (0 to 55 Hz) -25 C...+55 C (-3 F to 3 F) pole (30 g); 2 pole (280 g); 3 pole (430 g) 2 mm Voltage AC 220/240 5 A AC 277 3 A DC 24 V 4 A DC 60 V A DC220 V 0.4 A #8 2 AWG (line); #8 3 AWG (load) 69 Auxiliary Contact Modules 5.8 9 9.4 80.6 44 44 5 45.2 Accessories Jumpers Auxiliary contacts SPDT Type Side/Middle Part No. 3 pole bus, 0 x 00 mm, buses (9) 3 phase groupings 80A/00A 9970330000 3 pole bus, 6 x 20 mm, buses (4) 3 phase groupings 20A/30A 9970340000 3 pole bus, 6 x 00 mm, buses (9) 3 phase groupings 20A/30A 9970350000 pole bus, 2 x 20 mm, buses 2 breakers 80A/00A 9970360000 pole bus, 2 x 20 mm (insulated), buses 2 breakers 63A 999990000 Bus bar clamp 30A 9970370000 Auxiliary contacts 9970300000 Internal Auxiliary Wiring Diagram 4 2 Security hardware Lock out cover 9970380000 Marking Tags Adhesive label ETO 0/26, yellow (26 mm x 0 mm) 68640687 63