MapMarker Plus 11.1 Developer Installation Guide
Information in this document is subject to change without notice and does not represent a commitment on the part of the vendor or its representatives. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, without the written permission of MapInfo Corporation, One Global View, Troy, New York 12180-8399. 2005 MapInfo Corporation. All rights reserved. MapInfo, the MapInfo logo and MapMarker are trademarks of MapInfo Corporation and/or its affiliates. Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. The following trademarks are owned by the United States Postal Service: LACS Link, DPV, ZIP + 4, ZIP Code, ZIP, CASS, CASS Certified, Post Office, USPS, U.S. Postal Service and United States Postal Service. The information was published by MapInfo Corporation, a company which holds a non-exclusive license from the United States Postal Service to publish and sell Product information The price of the Product is neither established, controlled, or approved by the United States Postal Service. Portions 2005 Tele Atlas, Inc. (GDT, Inc.). MapInfo Corporate Headquarters: Voice: (518) 285-6000 Fax: (518) 285-6070 Sales Info Hotline: (800) 327-8627 Government Sales Hotline: (800) 619-2333 Technical Support Hotline: (518) 285-7283 Technical Support Fax: (518) 285-6080 Contact information for all MapInfo offices is located at: http://www.mapinfo.com/contactus. Adobe Acrobat is a registered trademark of Adobe Systems Incorporated in the United States. Products named herein may be trademarks of their respective manufacturers and are hereby recognized. Trademarked names are used editorially, to the benefit of the trademark owner, with no intent to infringe on the trademark. November 2005
Table of Contents Chapter 1: Installation..................................................... 5 Installation Overview........................................................... 6 Making the Transition from MapMarker Plus 10.x to MapMarker Plus 11.x................ 6 Address Dictionary............................................................ 6 DPV (Delivery Point Validation) Data............................................ 6 Upgrading from MapMarker 11.0 to 11.1........................................... 7 System Requirements.......................................................... 8 Operating Systems........................................................... 8 Web Servers................................................................ 9 Minimum Requirements........................................................ 9 Recommended Requirements................................................... 9 High Performance Requirements................................................. 9 System Recommendations...................................................... 9 Storing Data on Your Hard Drive................................................. 9 Performance Tuning......................................................... 10 Windows Installation Procedure................................................. 10 UNIX and Linux Installation Procedure............................................ 16 Installing in Console Mode..................................................... 16 Re-Installing MapMarker........................................................ 17 MDAC 2.7 and MapMarker ODBC Support......................................... 18 Starting MapMarker............................................................ 19 Desktop................................................................... 19 Developer.................................................................. 19 JNI Adapter Configuration File.................................................. 19 Chapter 2: Installer Reference............................ 20 Choose a Data Folder.......................................................... 21 Choose Shortcut Folder........................................................ 22 Choose Software Install Folder.................................................. 23 Choose Install Set............................................................. 24 Choose Java Virtual Machine................................................... 25 Enter Unlocking Code.......................................................... 26 Enter Serial Number........................................................... 27 Install Complete.............................................................. 28 Introduction.................................................................. 29 License Agreement............................................................ 30 Pre-Installation Summary....................................................... 31 Sample Web Environment Parameters............................................ 32
the guide title Table of Contents Index................................................................... 33 Product Name and version number 2005 MapInfo Corporation. All rights reserved. 4 filename.pdf
Installation 2 This chapter contains instructions for installing. Refer to this chapter for step-by-step instructions and other issues related to installation. In this chapter: Installation Overview............................... 14 System Requirements.............................. 16 System Recommendations.......................... 17 Windows Installation Procedure...................... 18 UNIX and Linux Installation Procedure................ 24 Re-Installing MapMarker............................ 25 MDAC 2.7 and MapMarker ODBC Support.............. 26 Starting MapMarker................................ 27 JNI Adapter Configuration File....................... 27
Developer Guide Chapter 2: Installation Installation Overview The MapMarker Plus developer product comes on one DVD-ROM and includes the desktop software, the Java SDK, and data. The installer installs all the product components in one easy procedure. The installer also handles all registry keys. The components installed during a complete installation are: MapMarker Plus desktop software (Windows only) MapMarker Plus Address Dictionary Java SDK Additional Developer Tools Servlet Container Making the Transition from MapMarker Plus 10.x to MapMarker Plus 11.x MapMarker Plus 11.x marks a departure from previous version of the MapMarker product. Version 11.x is built on the Java platform. Both versions of the product can operate side-by-side on the same computer. The only difference that you will see in the way that MapMarker Plus developer product looks and performs is in the installation. If you are a MapMarker Plus 10.x customer updating to MapMarker Plus 11.x, you will not be able to perform an upgrade to install it. You will need to do a full installation of the product. You may also notice that the installation procedure is slightly different than in previous versions. We have made every effort to make installing the product as easy as possible. Address Dictionary The MapMarker Plus Address Dictionary is installed during the installation of the MapMarker Plus software. You can install individual states of data, the entire United States, or ZIP + 4 centroids. During the installation, you will be asked to supply a data licensing code for the data that you purchased. To obtain the code, call the MapMarker License Authorization Desk at (800) 552-2511 option 3, between 8 a.m. and 7 p.m. ET, Monday through Friday. When you enter your code, the installer places a license on your system that matches your purchase and entitles you to access the appropriate data. The license file is located in the \data directory after installation. You may elect to install only a portion of the data set during the installation. To do this, select the Custom install option during the installation procedure. When you reach the Choose Install Set dialog, de-select any states that you do not want to install. DPV (Delivery Point Validation) Data The licensing code also handles the installation of the DPV data, as well as makes it usable. In previous versions of MapMarker Plus, an additional unlocking step was necessary to make the DPV data usable. This unlocking step is now only necessary to re-enable DPV in the event of a usage violation. If you purchased DPV, the license code is valid for fourteen days from the date that you obtained the code. If you use a license code that has expired, you will receive the following message: 2005 MapInfo Corporation. All rights reserved. 14 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation You will be able to continue with the installation of the MapMarker software, developer components, and Address Dictionary data, but to enable DPV you will need to obtain a new authorization code from Customer Service, and then use the CASS Authorization Utility to enable DPV use. To add DPV to an existing installation, you will need to remove your MapMarker installation and install it again. Please see Re-Installing MapMarker on page 25 for more information. Upgrading from MapMarker 11.0 to 11.1 To upgrade your 11.0 installation to, do the following: 1. Start the install program by running SETUP.EXE from the media. Click Install the product in the MapMarker Installation Options screen. 2. The installer detects that you have MapMarker Plus 11.0 installed and asks if you want to upgrade your 11.0 installation to 11.1. 3. Click Upgrade. 4. The installer begins copying files. This will take a few minutes. 5. The Upgrade Complete dialog displays when the installation is finished. p 2005 MapInfo Corporation. All rights reserved. 15 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation 6. Click Done. If you purchased different data than you did for 11.0, such as additional Address Dictionary data or DPV data, remove your installation of 11.0, and install v. 11.1 using the new serial and unlocking code. System Requirements This section describes the software and hardware requirements for running MapMarker Plus. Operating Systems MapMarker Plus runs on the following operating systems: Windows 2000 with SP4 Windows XP with SP2 Windows 2003 Enterprise Edition Windows 2000 Advanced Server with SP4 Solaris 2.9, 2.10 HP-UX 11.0 Red Hat Linux Java Virtual Machine MapMarker Plus requires a Java Virtual Machine (JVM) to run. The following JVMs are supported: JVM v. 1.4.1 or later MapMarker ships with JVM v. 1.5. During the installation, you will have the option of installing one of the JVMs that ships with MapMarker, or using one that you already have installed on your computer. 2005 MapInfo Corporation. All rights reserved. 16 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation Web Servers The following Web servers are supported: Tomcat 4.1.1.8, 5.x (MapMarker ships with v. 5.0) Sun One 7.0 BEA WebLogic 8.1 WebSphere 5.1 and 6.0 Minimum Requirements The minimum system requirements for MapMarker Plus 11.x on a full installation are: 800 Mhz Pentium processor or equivalent 256 MB RAM 5 GB available disk space Recommended Requirements The recommended system requirements on a full are: 1 Ghz processor or better 512 MB RAM 10 GB available disk space High Performance Requirements For high performance, the following system requirements should be in place: 2.5 Ghz dual processor or better 1 GB RAM or better 10 GB available disk space The MapMarker software requires about 25 MB of available hard drive space. The Plus Address Dictionary requires approximately 2.63 GB (for nationwide data) of disk storage space. The DPV data requires approximately.5 GB of disk storage space. System Recommendations Please note the following recommendations in order to maximize the performance of your MapMarker Plus installation. Storing Data on Your Hard Drive To maximize MapMarker s performance, we recommend that the Address Dictionary data be stored on a local hard drive. The data resides in the data directory under the MapMarker program directory (default is c:\program Files\MapInfo\MapMarker_USA\data). 2005 MapInfo Corporation. All rights reserved. 17 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation Performance Tuning To get the most out of MapMarker s geocoding capabilities, consider these tips for optimizing your system. Use the fastest processor available to you. Have enough memory so that the operating system can allocate some memory to your disk cache. Copy the Address Dictionary to your hard drive. Sort your table by ZIP Code. Choose exact match criteria for all (house number, street name, city name, ZIP Code). Do not create points automatically. Windows Installation Procedure 1. Place the MapMarker DVD into your DVD-ROM drive. On Windows platforms, if the installation does not automatically start, choose Run from the Windows 2000/2003/XP START button. From the Run dialog, type D:\SETUP.EXE in the Open command box, where D is the drive letter of your DVD-ROM. Click OK. The MapMarker Installation Options screen displays on your screen. 2. Click the INSTALL MAPMARKER... button. 3. The Introduction dialog displays on the screen. 4. Click NEXT to continue. The License Agreement dialog displays on the screen. 2005 MapInfo Corporation. All rights reserved. 18 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation 5. After reading the License Agreement, click the I ACCEPT THE TERMS OF THE LICENSE AGREEMENT BUTTON, and then click NEXT to continue. The Enter Serial Number dialog displays on the screen. 6. At the Enter Serial Number dialog, type your MapMarker Plus serial number. The serial number is located on a sheet of stickers in the MapMarker Plus package. Click NEXT to continue. The Enter Unlocking Code dialog displays on the screen. 2005 MapInfo Corporation. All rights reserved. 19 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation 7. At the Enter Unlocking Code dialog, type your data unlocking code in the box. This code enables the installer to create a license file for your system that gives you access to the data you purchased. Please call (800) 552-2511 option 3, between 8 am and 7 pm, EST, Monday through Friday, and the MapMarker License Authorization desk will provide your unlocking code. Have your product serial number ready when you call. If you have purchased a single state, or a six-state pack, you will be able to install those states after entering your unlocking code. 8. Click NEXT to continue. The Choose Install Set dialog displays on the screen. 9. In the Typical Install Set, all of the product components are installed by default. To see a description of each component, click on the component to highlight it. A description for the component displays in the Description box. To select which components you want to install, choose Custom in the Install Set drop-down list. Clear the check boxes of the components you do not want to install. 10. When you are finished, click NEXT to continue. The Installation Type dialog displays on the screen. 2005 MapInfo Corporation. All rights reserved. 20 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation Select the location of the MapMarker Plus software. You can use the default location: C:\Program Files\MapInfo\MapMarker\MapMarker_USA or click CHOOSE to display the Browse for Folder dialog, where you can navigate to the desired location. Click OK in the Browse for Folder dialog when you are finished. If you decide after selecting an alternative location that you would prefer the default location, click RESTORE DEFAULT FOLDER in the Choose Install Set dialog. 11. Click NEXT in the Choose Software Install Folder dialog to continue. The Choose a Data Folder dialog displays on the screen. 2005 MapInfo Corporation. All rights reserved. 21 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation 12. Select the location of the MapMarker data. You can use the default location: C:\Program Files\MapInfo\MapMarker\MapMarker_USA\Data or click CHOOSE to display the Browse for Folder dialog, where you can navigate to the desired location. Click OK in the Browse for Folder dialog when you are finished. If you decide after selecting an alternative location that you would prefer the default location, click RESTORE DEFAULT FOLDER in the Choose a Data Folder dialog. 13. Click NEXT in the Choose a Data Folder dialog to continue. The Choose Java Virtual Machine dialog displays on the screen. Do one of the following: Select the Install a Java VM specifically for this application button to install the Java virtual machine that comes with MapMarker Plus. Select the Choose a Java VM already installed on this system button to select a Java virtual machine that you already have installed on the computer. 2005 MapInfo Corporation. All rights reserved. 22 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation Select the Search for Others button to have the installer search your computer for an installed JVM. Select the Choose Another button if you know where your JVM is installed. You must have a JVM v. 1.4.1 or later. Note: If you select the Choose a Java VM already installed on this system button and there is no VM installed on your computer, you will receive an error message when you click NEXT. 14. Click NEXT to continue. The Sample Web Environment parameters dialog displays. Enter the hostname and port you want to use with the sample web environment. The default hostname is the name of your computer, and the default port number is 8095. 15. Click NEXT to continue. The Choose Shortcut Folder dialog displays on the screen. Click the corresponding button of the desired location of the product icons. Click the Don t create icons button if you do not want to create product icons. If you clicked the OTHER button, and you want to use a location different from the default, click the CHOOSE button to navigate to the desired location. 16. Click Next to continue. The Pre-Installation Summary dialog displays on the screen. 2005 MapInfo Corporation. All rights reserved. 23 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation 17. Review your install selections. To edit any of the selections, click the Previous button to go back to the earlier dialogs. 18. When you are satisfied with your installation choices, click INSTALL. A progress dialog displays as the software and data is installing. 19. When the installation is finished, the Install Complete dialog displays on the screen. Click DONE to exit the installer. UNIX and Linux Installation Procedure On HP-UX, Solaris, or Linux platforms, do the following: 1. Place the MapMarker DVD into your DVD-ROM drive. 2. Open a terminal window. 3. At the command prompt enter: sh <path to media>/startinstall.sh to start the MapMarker installer, where path to media is the full path to the mounted installer media, e.g., /dvdrom/dvdrom0. Installing in Console Mode To run the installation program in console mode: 1. Change directories to the instdata directory on the installation media, and then to the directory appropriate to your platform (HP-UX, Solaris, or Linux). 2. In your platform s directory, descend to the directory named vm. 3. Enter install.bin -i console or sh /install.bin as appropriate for your platform. The installer detects that there is no user interface and runs itself in console mode. Note: The MapMarker console mode installation works only with the DVD media. If you requested CDs, you will need to perform the GUI installation. 2005 MapInfo Corporation. All rights reserved. 24 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation Re-Installing MapMarker If you purchase components and data subsequent to your MapMarker purchase, such as DPV or licenses for additional states, you will need to remove your current installation of MapMarker Plus, and then install it again. If you re-launch the installation program from the DVD, it will guide you through the removal and reinstallation process: 1. Place the MapMarker DVD into your DVD-ROM drive. If the installation does not automatically start, from the Windows 2000/2003/XP START button, choose RUN. From the Run dialog, type D:\SETUP.EXE in the Open command box, where D is the drive letter of your DVD-ROM. Click OK. 2. A dialog displays on the screen with a message, indicating that you already have MapMarker Plus installed and that to make change to your current installation, you must remove MapMarker and reinstall it. 3. Click REMOVE to remove your installation of MapMarker Plus. When the existing installation of MapMarker Plus has been removed, the installer continues, and the Enter Serial Number dialog displays on the screen. Your serial number is already filled in. 4. Click NEXT to continue. The Enter Unlocking Code dialog displays on the screen. The license code from your original installation is already filled in. You will need to call Customer Service for a new license code in the following circumstances: You are a current DPV customer and your original license code is over fourteen days old. You are installing DPV as an add-on. You are installing additional data. 2005 MapInfo Corporation. All rights reserved. 25 MapMarker11_1Developer.pdf
Developer Guide Chapter 2: Installation Please call MapInfo Customer Service: (800) 552-2511 option 3, between 8 am and 7 pm, EST, Monday through Friday, and the MapMarker License Authorization desk will provide your unlocking code. Have your product serial number ready when you call. If you have purchased a single state, or a six-state pack, you will be able to install those states after entering your unlocking code. If you proceed to the next dialog without changing your unlock code, and a new code was needed, you will need to exit and restart the installer to change the code. 5. Click NEXT to continue. The rest of the installation procedure is the same as it is for a new install. For more information, please see Windows Installation Procedure on page 18. MDAC 2.7 and MapMarker ODBC Support Microsoft Data Access Components 2.7 is required to use MapMarker with a SQL database. This component is installed automatically when you install MapMarker Plus 11.x either on a standalone workstation or on a client machine. The MapMarker Plus installer and the client setup program both install the Jet 4.0 database engine for use with Microsoft Access. The Jet 4.0 package and the MDAC 2.7 installer together install a number of ODBC drivers for use with MapMarker. Among them are the following supported drivers: SQL Server v. 2000 Microsoft Access (*.mdb) v. 4.00 MapMarker also supports the following Oracle driver: Oracle 9i Release 2 You must install the Oracle driver separately. To use the driver, you must have the Oracle 9i client installed. 2005 MapInfo Corporation. All rights reserved. 26 MapMarker11_1Developer.pdf
Developer Guide Starting MapMarker Chapter 2: Installation Please follow these instructions to start the MapMarker Plus desktop and developer products. Desktop On Windows 2000/2003/XP, choose MapMarker Plus 11.x Desktop from the Start menu or Shortcut menu. Developer To start the Java server On Windows 2000/2003/XP, choose MapMarker USA> Start MapMarker Plus USA Server from the Start menu or Shortcut menu. You can also start the Java server by running startup.bat (Windows) or startup.sh (Solaris, HP-UX, and Linux). This file is located in the \SDK\MapMarker-4.0\bin folder. Note: On HP-UX and Solaris, you can start either the RPC or Java server. On Linux, only the Java server is available. JNI Adapter Configuration File The adapter uses a configuration file that is put down at the time of installation, geojni.cfg. On Windows systems it is located in the MapInfo\MapMarker\MapMarkerPlusUSA\SDK\Additional Tools folder where MapMarker Plus is installed. On UNIX systems it can be located anywhere and have any name. The environment variable CONFIG_FILE_PATH must be set to the full path of the file (including the filename) and exported in the environment of an application using the adapter. export CONFIG_FILE_PATH=/opt/mapinfo/mapmarker/geojni.cfg You may want to modify this file to increase the memory usage. You also may want to take note of the location of the file, for technical support purposes. For more specific information about the configuration file settings, see JNI Adapter Configuration File Settings in Appendix B on page 85. 2005 MapInfo Corporation. All rights reserved. 27 MapMarker11_1Developer.pdf
Installer Reference 2 This installer reference is a feature reference for the product installer and is organized alphabetically by dialog box name. In this chapter: Choose a Data Folder............................... 21 Choose Shortcut Folder............................. 22 Choose Java Virtual Machine........................ 25 Enter Unlocking Code.............................. 26 Enter Serial Number................................ 27 Install Complete................................... 28 Introduction....................................... 29 License Agreement................................ 30 Pre-Installation Summary........................... 31 Sample Web Environment Parameters................. 32
Developer Installation Guide Choose a Data Folder Chapter 2: Installer Reference The Choose a Data Folder dialog enables you to specify a location for the MapMarker Plus data. Please choose a folder Restore Default Folder Choose Cancel Help Previous Next Enter the install location for the data. The default path and folder is C:\Program Files\MapInfo\MapMarker\MapMarkerPlusUSA-Data. Click to reselect the default folder as the data location. Click to navigate to another location for the MapMarker data. Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 21 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Choose Shortcut Folder Chapter 2: Installer Reference The Choose Shortcut Folder dialog enables you to specify where you want to create product shortcut icons. You can accept the default location, browse to another location, or choose one of the other available options. In a new Program Group In an existing Program Group In the Start Menu On the Desktop In the Quick Launch Bar Other Don t create icons Select to place shortcut icons in a new program group. The default name of the new program group is MapMarker Plus USA. Type a different name if desired. Select to place shortcut icons in an existing program group. Select the program group you want from the drop-down list. Select to place shortcut icons in the Start menu. Select to place shortcut icons on the desktop. Select to place shortcut icons on the Quick Launch Bar. Select to choose a different location for the shortcut icons. Select if you do not want to create shortcut icons. Create Icons for All Users Cancel Help Click to exit the installation wizard without installing the program. Click to view help for this dialog. 2005 MapInfo Corporation. All rights reserved. 22 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Chapter 2: Installer Reference Previous Next Click to go back to the previous dialog. Click to proceed to the next dialog. Choose Software Install Folder The Choose Software Install Folder dialog enables you to specify the location of the MapMarker Plus USA program. You can use the default location, specify a different location directly into the text box, or use the Choose button to navigate to a different location. If, after selecting an alternate location for the software, you decide that you would prefer to use the default location, simply click the Restore Default Folder button to respecify the default folder as the location. Where would you like to install? Restore Default Folder Choose Cancel Help Previous Next Enter the path of the location for the MapMarker Plus software. The default location is C:\Program Files\MapInfo. Click to reselect the default folder as the location for the MapMarker Plus software. Click to navigate to the location where you want to install the Map- Marker Plus software. Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 23 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Choose Install Set Chapter 2: Installer Reference The Choose Install Set dialog asks you for the type of installation you want to perform. Install Set Cancel Help Previous Next Select either Typical or Custom. Select Typical to install the complete software and all of the licensed data. Select Custom to choose which components and what portion of your data to install. Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 24 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Choose Java Virtual Machine Chapter 2: Installer Reference Install a Java VM specifically for this application Choose a Java VM already installed on this system Search for Others Choose Another Cancel Help Previous Next Select this option to install the Java VM that comes with MapMarker. Select this option to install a Java VM that is already on your system. To select a Java VM, click on one of the installed VMS listed in the box. Click Search for Others to locate a different Java VM. Click to navigate to the location of a different Java VM. Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 25 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Enter Unlocking Code Chapter 2: Installer Reference In the Enter Unlocking Code dialog, you must enter a data unlocking code. This code enables the installer to create a license file for your system that gives you access to the data you purchased. To obtain your data unlocking code, please call the MapMarker License Authorization desk at (800) 552-2511, Monday through Friday, between 8 am and 7 pm. Have your product serial number ready when you call. Unlocking Code Cancel Help Previous Next Enter the data unlocking code into the box. Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 26 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Enter Serial Number Chapter 2: Installer Reference The Enter Serial Number dialog indicates that the installer is ready to begin the installation. Serial Number Cancel Help Previous Next Enter the product serial number into the box. The serial number is located on a sheet of stickers in the MapMarker Plus package. Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 27 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Install Complete Chapter 2: Installer Reference The Install Complete dialog indicates that MapMarker has been installed successfully. Cancel Help Previous Done Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to exit the installation. 2005 MapInfo Corporation. All rights reserved. 28 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Introduction Chapter 2: Installer Reference The Introduction dialog is the start of the MapMarker Plus installation. It displays when you launch the MapMarker Plus installer from the DVD (or CD-ROM if you selected the alternate media when you purchased MapMarker). Cancel Help Previous Next Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 29 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide License Agreement Chapter 2: Installer Reference The License Agreement enables you to specify that you accept the license agreement for the MapMarker Plus product. You must accept the license agreement to proceed with the installation. I accept the terms of the License Agreement I do NOT accept the terms of the License Agreement Cancel Help Previous Next Click to accept the terms of the license agreement and proceed with the installation. Click to deny the terms of the license agreement and exit the installation. Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 30 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Pre-Installation Summary Chapter 2: Installer Reference Please review your installation settings in the Pre-Installation Summary dialog. If you want to change any of your settings, click the Previous button to return to the setting(s) you want to change. Cancel Help Previous Install Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to start the installation. 2005 MapInfo Corporation. All rights reserved. 31 MapMarker11_1DeveloperInstall.pdf
Developer Installation Guide Sample Web Environment Parameters Chapter 2: Installer Reference In the Sample Web Environment Parameters dialog, specify the hostname and port to be used for configuring the example Web environment. Hostname Specify the hostname for the sample Web environment. Port Specify the port number. The default port number is 8095. Cancel Help Previous Next Click to exit the installation wizard without installing the program. Click to view help for this dialog. Click to go back to the previous dialog. Click to proceed to the next dialog. 2005 MapInfo Corporation. All rights reserved. 32 MapMarker11_1DeveloperInstall.pdf
Index A address dictionary installing 6 storing data 9 storing on hard drive 9 C choosing shortcuts 22 configuration file JNI adapter 19 console mode installation 16 custom install set 24 D data installing 6, 21 storing 9 unlocking code 26 database drivers 18 DPV (Delivery Point Validation) installation 6 I installation console mode 16 data 21 data folder 21 re-installing 17 18 software folder 23 system recommendations 9 system requirements 8 9 UNIX/Linux procedure 16 upgrading 7 Windows procedure 10 16 J Java Virtual Machine 8, 25 JNI adapter configuration file settings 19 L license agreement 30 O operating systems 8 P performance increasing 10 R re-installing MapMarker 17 18 remote database drivers 18 S starting MapMarker 19 Sun One 7.0 9 system recommendations 9 system requirements 8 9 T transition to MapMarker Plus 11.0 6 typical install set 24 U unlocking code 26 upgrading your installation 7 W Web environments 9, 32 WebLogic 8.1 9 WebSphere 5.1 and 6.0 9