Amplifiers, Counters, Timers & Controls Panel Meter 814 Counter/Timer/Rate Indicator 815-817 Speed Monitor 818-819 Signal Converter 820-822 Power Supplies/Amplifier 823-824 813
Panel Meter Panel Meter with Dual Relay 5 digit LED display 2 relay outputs 2 programmable limit values Plug-in screw terminals Provides 24VDC to sensors 120 or 240VAC supply The DA5-IU-2K-V is a multi-function indicator that allows visual display of the connected analog signal. The input can either be analog voltage or current, typically provided by an ultrasonic or similar sensing device. The indicator has two programmable relay outputs for level detection, a scalable 5 digit display and a 24 VDC/100 ma output supply to power the sensor. SUPPLY VOLTAGE: SUPPLY VOLTAGE TO SENSOR SUPPLY TO SENSOR CONTROL S P+F ANALOG / VOLTAGE SENSORS IMPEDANCE (ANALOG ) VOLTAGE IMPEDANCE (ANALOG VOLTAGE) CONTROL OUTPUTS Relay AC RATING VOLTAGE POWER DC RATING RESPONSE ENERGIZE TIME DE-ENERGIZE TEMPERATURE OPERATING TIME STORAGE PROTECTION FRONT WINDOW (IEC) ENTIRE UNIT DA5-IU-2K-V 110/240VAC, 6VA 24VDC 100mA 0/4-20mA 50Ω 0/2-10VDC -10 to +10VDC >1MΩ 2-Form C 260V 3A 250V, 3A resistive load 300VDC, 3A 10ms 10ms +14 F to +122 F -4 F to +158 F IP65 IP20 Model DA5-IU-2K-V size #16AWG High Level Model DA5-IU-2K-V 7 83 73 Low Level Application: Level controller 96 3 814
Counter / Timer POWER NOMINAL VOLTAGE SUPPLY LOW LEVEL VOLTAGE HIGH LEVEL MAX FREQUENCY FILTERED FREQUENCY IMPEDANCE OUTPUT RELAY OUTPUT (FORM C) RELAY RESPONSE TIME SENSOR SUPPLY OPERATING TEMPERATURE RELATIVE HUMIDITY PROTECTION FRONT WINDOW (IEC) ENTIRE UNIT KCT1-6SR-V 90-250VAC 5VA max. NPN/PNP (2 or 3-wire) 0-4VDC 12-30VDC 20kHz 30Hz 10KΩ 250VAC/3A; 300VDC/3A 7ms 24VDC; 100mA 14 F to +122 F 80% non-condensing IP65 Counter/Timer/ Rate Indicator Operating range up to 20kHz Preset with relay output relay status indication 120/240 VAC power supply Push-button programmable Scalable six digit LED display Auxiliary sensor power supply The KCT1-6SR-V multi-function counter/timer accepts NPN/PNP input pulses from external sensors and can display count, time or rate information. The unit has a high visibility 6 digit LED display and can be easily programmed using the frontmount pushbuttons. Other Features: Adding /Subracting mode Count up/down Manual or external reset Quadrature input capable Count gating input Programmable preset Accepts 2 or 3-wire inputs KCT1-6SR-V 16 90 815
Counter / Timer Counter/Timer/ Rate Indicator Operating range up to 10kHz Preset with relay output 120/240 VAC power supply Push-button programmable Scalable 6 digit LCD display Auxiliary sensor power supply The KCN1-6SR-V multi-function counter/timer accepts NPN/PNP input pulses from external sensors and can display count, time or rate information. This unit has a programmable preset for limit detection and features a 2-line LCD display so that count value and preset may be shown simultaneously. Other Features: Adding /Subracting mode Count up/down Manual or external reset Quadrature input capable Count gating input Programmable preset Accepts 2 or 3-wire inputs POWER SUPPLY NOMINAL VOLTAGE LOW LEVEL VOLTAGE HIGH LEVEL MAX FREQUENCY FILTERED FREQUENCY IMPEDANCE OUTPUT RELAY OUTPUT (FORM C) RELAY RESPONSE TIME SENSOR SUPPLY OPERATING TEMPERATURE RELATIVE HUMIDITY PROTECTION FRONT WINDOW (IEC) ENTIRE UNIT KCN1-6SR-V 90-260VAC 4VA max. NPN/PNP (2 or 3-wire) 0-4VDC 12-30VDC 10kHz 30Hz 10kΩ 250VAC/3A; 300VDC/3A 6ms 14.4-27.6VDC, 80 ma 32 F to +122 F 80% non-condensing IP65 Contact Factory KCN1-6SR-V 16 88 816
Counter / Timer POWER NOMINAL VOLTAGE SUPPLY LOW LEVEL VOLTAGE HIGH LEVEL MAX FREQUENCY FILTERED FREQUENCY IMPEDANCE OUTPUT RELAY OUTPUT (FORM C) RELAY RESPONSE TIME SENSOR SUPPLY OPERATING TEMPERATURE RELATIVE HUMIDITY KCN1-6WR-V 90-260VAC 4VA max. NPN/PNP (2 or 3-wire) 0-4VDC 12-30VDC 10kHz 30Hz 10kΩ 250VAC/3A; 300VDC/3A 6ms 14.4 to 27.6VDC, 80mA 32 F to +122 F 80% non-condensing Counter/Timer/ Rate Indicator with 2 Relay s Operating range up to 10kHz Two Presets with 2 relay outputs 120/240 VAC power supply Pushbutton programmable Scalable 6 digit LCD display Auxiliary sensor power supply PROTECTION FRONT WINDOW (IEC) ENTIRE UNIT IP65 Contact Factory The KCN1-6WR-V multifunction counter/ timer accepts NPN/PNP input pulses from external sensors and can display count, time or rate information. The unit has two programmable preset limits that can be easily programmed and features a 2 line LCD display so that count value and preset may be shown simultaneously. Other Features: Adding /Subracting mode Count up/down Manual or external reset Model KCN1-6WR-V Quadrature input capable 16 88 Count gating input Two programmable presets 817
Standstill Monitoring Standstill/ Zero-Speed Monitor Operating range up to 2kHz Standstill detection at 0.1 Hz, 0.5 Hz, 2 Hz, 10 Hz LED status indicators Switch adjustable 3 wire PNP, push-pull, NAMUR or rotary encoder inputs accepted Two relay outputs POWER NOMINAL VOLTAGE SUPPLY NAMUR SENSOR OPEN LOOP VOLTAGE SHORT CIRCUIT SWITCHING POINT IMPEDANCE PNP SENSOR HIGH LOW FREQUENCY RANGE CUTOFF FREQUENCY STARTUP OVERRIDE KFD2-SR2-2.W.SM 20-30VAC 1.5W 8.2VDC 6.5mA 1.2-2.1mA hysteresis 0.2 ma 1.2kΩ 3-wire PNP >2.5VDC <1.0VDC 2k Hz 0.1Hz, 0.5Hz, 2Hz, 10Hz 5 seconds/20 seconds The KFD2-SR2-2.W.SM is zero speed/ standstill monitor that accepts input frequency pulses and triggers an output when the frequency drops below the selected level. The available diagnostic LED s allow for rotation detection, limit trip indicator, power on and hardware error indication. The unit is easily programmed via switches mounted on the front of the unit. te: External Sensor supply required for 3-wire sensors. OUTPUT RELAY OUTPUT (2 FORM C) ACTIVATION DELAY OPERATING TEMPERATURE PROTECTION (IEC) 250VAC/2A; 40VDC /2A 20ms -4 F to +140 F IP20 Model KFD2-SR2.W.SM 118 115 20 818
Multi-function POWER NOMINAL VOLTAGE SUPPLY AC POWER FREQUENCY NAMUR SENSOR OPEN LOOP VOLTAGE SHORT CIRCUIT SWITCHING POINT IMPEDANCE NPN/PNP SENSOR HIGH LOW MAX KFU8-DW-1.D 24VDC +15%/-10%; 120-240VAC ±10% 5W/5VA 47-63Hz 8.2VDC 6.5mA 1.2-2.1mA hysteresis 0.2 ma 1.2kΩ 3-wire NPN/PNP; isolated 16-30VDC 0-6VDC 10 ma, impedance 3kΩ Rotational Speed Monitor Operating range up to 5kHz Preset with Relay output Multi-range power supply Push-button programmable Start-up delay Auxiliary Sensor power supply LED display; Hz. or 1/min 2, 3 and 4-wire, NAMUR or encoder FREQUENCY RANGE OUTPUT RELAY (FORM C) ACTIVATION TIMER FUNCTION SENSOR SUPPLY OPERATING TEMPERATURE PROTECTION (IEC) 4999Hz 250VAC/2A; 40VDC /2A <20ms ON/OFF delay 24VDC ±10%, 30mA, short circuit proof 14 F to +156 F IP20 The KFU8-DW-1.D monitors for an over-speed condition by comparing the input frequency to the programmed preset limit value. This preset limit frequency, with hysteresis, can be easily programmed using the pushbuttons located on the front of the unit. When an overspeed condition occurs. It can be signaled via the relay output that can be conditioned through the use of timer function; delay on/off and pulse extension features. The unit also provides a start-up override feature, which allows the relay output to be controlled by an external input to prevent false triggering at start up. Model KFU8-DW-1.D 40 115 107 819
Frequency Converter Frequency to Voltage/Current Converter Operating range up to 10kHz Isolated analog outputs Multi-range power supply Push-button programmable Frequency divided pulse output Auxiliary sensor power supply POWER NOMINAL VOLTAGE SUPPLY AC POWER FREQUENCY NAMUR SENSOR OPEN LOOP VOLTAGE SHORT CIRCUIT SWITCHING POINT IMPEDANCE NPN/PNP SENSOR HIGH LOW MAX KFU8-FSSP-1.D 24VDC +15%/-10%; 115-230VAC ±10% 5W/5VA 47-63Hz 8.2VDC 6.5mA 1.2-2.1mA hysteresis 0.2 ma 1.2kΩ 3-wire NPN/PNP isolated 16-30VDC 0-6VDC 10 ma, impedance 3kΩ The KFU8-FSSP-1.D is a signal conditioner that converts input frequency pulses to an analog voltage or current signal. The user can scale the maximum output signal using a scaling parameter or the teach method via the pushbuttons located on the front of the unit. The front of the unit also has a 4 digit LED display to assist in configuration. FREQUENCY RANGE OPERATING RANGE DEVIATION OUTPUT ANALOG OUTPUTS ANALOG VOLTAGE 10kHz 0.001-10kHz 0.2% of full scale value Isolated 0-10VDC, 2-10VDC, 30mA max LOAD IMPEDANCE 330Ω The unit provides isolation for the sensor inputs as well as for the analog output. RESOLUTION ANALOG 10mV 0-20mA, 4-20mA LOAD IMPEDANCE 600Ω Model KFU8-FSSP-1.D RESOLUTION SENSOR SUPPLY FREQUENCY DIVIDER OUTPUT 20µA 24VDC ±10%, 30mA, short circuit proof 20mA, short circuit proof OPERATING TEMPERATURE -13 F to +140 F PROTECTION (IEC) IP20 40 115 107 820
3-wire to Relay Converter : VOLTAGE RELAY OUTPUT The output is isolated from the input and supply AC RATING VOLTAGE POWER DC RATING SWITCHING FREQUENCY RESPONSE TIME ENERGIZE WORKING TEMPERATURE RANGE DE-ENERGIZE KCD2-R 3-wire NPN/PNP 24VDC 16mA SPDT 250V 2A 30VDC/2A 10Hz max. 6ms 2ms -14 F to +140 F Sensor Converter SPDT relay output Compact Din rail mount This device can be used to convert NPN/PNP sensor outputs to relay contact output. The sensor must be supplied from a seperate power supply unit. HOUSING MATERIAL Makrolon #65 size #16AWG KCD2-R 3- Input 2+ LED Yellow: Status 60 20 40 4 6 5 821
NAMUR to 3-wire Sensor Amplifier/ Converter Converts NAMUR to standard 3-wire NPN or PNP n-isolated These devices provide an inexpensive method of converting a NAMUR output proximity sensor to 3-wire DC (NPN or PNP). Models with the suffix "L" offer monitoring of the input circuit. If either wire is broken the output will turn off. These devices are not isolated and not intrinsically safe. Lead breakage monitoring can be disabled via jumper connection between terminals 1 and 3. (terminals 1+, 2-) LEAD BREAKAGE MONITORING OUTPUT (terminal 4) E/EL Transitor rmally open E2/E2L VOLTAGE DROP SHORT CIRCIUT PROTECTION POWER SUPPLY Amplifier Supply Voltage (terminals 5+, 6-) CONSUMPTION LED(S) SWITCHING FREQENCY PROTECTION IEC AMBIENT TEMPERATURE HOUSING MATERIAL KCD2-E KCD2-E2 NAMUR NPN, Sinking PNP, Sourcing 1.8VDC 200mA 10-30VDC 22mA (1) 1kHz IP20-14 F to +158 F Makrolon #65 KCD2-EL KCD2-E2L NAMUR NPN, Sinking PNP, Sourcing 1.8VDC 200mA 10-30VDC 22mA (1) 1kHz IP20-14 F to +158 F Makrolon #65 Input Sensor Function Diagram 1+ 1+ 2- Lead breakage ("L" models only) monitoring disable 3 1+ 2-3 KCD2-E KCD2-E2 KCD2-EL KCD2-E2L LED Yellow: Status NAMUR Inductive Sensor NAMUR Capacitive Sensor ON LED ON I 0.1 ma 60 OFF OFF 4+ 6-5+ Supply voltage 20 40 822
Switch Amplifier/Relay SUPPLY VOLTAGE: The supply is isolated from the input and output : The input is isolated from the output and supply MAXIMUM VOLTAGE MAXIMUM RELAY OUTPUT The output is isolated from the input and supply AC RATING VOLTAGE POWER DC RATING SWITCHING FREQUENCY RE-1 120VAC 3VA 3-wire NPN/PNP 24VDC 80mA SPDT 250V 4A 500VA 110V/0.2A, 60V/0.4A, 24V/4.0A 10Hz max. Sensor Power Supply with Single Relay SPDT output Accepts 120VAC Supplies DC power to sensor The RE-1 is a DC power supply for single switch point output sensors or other 3-wire NPN/PNP output devices. It requires a 120VAC supply voltage and provides a SPDT relay output. RESPONSE TIME ENERGIZE DE-ENERGIZE 20ms 10ms Model RE-1 WORKING TEMPERATURE RANGE -14 F to +140 F HOUSING MATERIAL NORYL SE O size #16AWG Operating Controls and Indicators: Front View RE-1 110 30 between holes 40 Oblong hole 4.8 x 5.8 thru (2 places) Operating mode Input pnp npn 4 5 6 2 1+ Input supply 3-60 between holes 70 8 9 7 11 12 Supply voltage 823
Switch Amplifier/Relay Sensor Power Supply with Dual Relay s Dual SPDT outputs Dual NPN or PNP inputs Supplies DC power to sensor This device is a DC power supply for 2-single, or 1-dual switch point output sensors or 3-wire NPN/PNP devices. It requires 120VAC supply voltage and provides two separate SPDT relay outputs. SUPPLY VOLTAGE: The supply is isolated from the input and output : The input VOLTAGE is isolated from the output and supply RELAY OUTPUT: The output is isolated from the input and supply AC RATING VOLTAGE POWER DC RATING SWITCHING FREQUENCY RESPONSE TIME ENERGIZE DE-ENERGIZE WE77-RE2 120/240VAC 4VA 24VDC 160mA SPDT (2) max. 250V max. 4A max. 500VA 110V/0.2A, 60V/0.4A, 24V/4.0A 10Hz max. 20ms 10ms Model WE77-RE2 WORKING TEMPERATURE RANGE -14 F to +140 F HOUSING MATERIAL NORYL SE O size #16AWG Switching Input Input Input supply I II pnp npn 5 6 7 2 4 1+ 3- WE77-RE2 50 between holes ~ 60 110 Oblong hole 4.8 x 5.8 thru (2 places) 60 between holes 70 ~ 11 12 10 14 15 13 16 17 18 I II Supply voltage 824