Joystick with grip Multi-axial miniature joystick based on Hall Effect technology J... + space-saving design + highly reliable and long lifetime due to contactless Hall Effect technology + integrated third axis or button in handle + ratiometric output signal 0.5...4.5 VDC + high protection class IP67 for extreme environments + operating temperature range -40 to +85 C + redundant/semi-redundant output signal optional Use Thanks to its very compact design, the J joystick is ideally suited for use in small control panels such as arm rests and remote control consoles. The contactless Hall Effect technology enables precise control in applications such as remote controls for cranes, robot monitoring as well as lab and medical equipment. Options For safety related applications, various versions of the grip such as the third axis (also called z-axis ) or an additional push button switch allow the control of additional functions. J with integrated third axis J Version.4 Page of
Mechanical assembly» Dimensions» Grip variant 3 with z-axis» Grip variant 2 with button» Grip variant *2 *2 * *2 LifY-t 0. mm 2 (grip) LifY-t 0.34 mm 2 (x-/) * Assembly height with assembly type: Installation into the console from below, screw connection from above *2 Assembly height with assembly type: Installation into the console from above, screw connection from above» Installation dimensions Assembly type Mounting Installation from below / installation from above into the customized console or the armrest 4x M3 screws; optionally screwed in from above or below (not included with delivery) Panel depth Installation from above: not relevant The Installation relevant corresponding from below: technical min. 2 mm, documents max. 4 will mmbe supplied with the product. J Version.4 Page 2 of
Installation from below, screw connection from above Assembly cut-out Customized mounting console M3 mounting thread in joystick module Installation from below, screw connection from below Assembly cut-out Customized mounting console Inner thread in mounting ring J Version.4 Page 3 of
Installation from above, screw connection from above Assembly cut-out M3 mounting thread in the installation console necessary Customized mounting console Key mechanical data Technology contactless Hall sensor technology Mechanical life 2 m cycles ) Static capacity x-/: 200 N at 50 mm from the pivot point Axes standard 2, optional z-axis 2) Deflection x-, ± 5 Deflection z-axis ± 30 rotation angle area Push button stroke total 2.5 mm Operating temperature range -25 to +85 C (-40 to +85 C without push button or z-axis) Storage temperature -40 to +85 C Protection class electronic IP67 DIN EN 6052 Protection class mechanical IP67 DIN EN 6052 sealing of the console required Connection Litz wire with Molex-Micro-Fit 3.0 connector 3) Weight approx. 4 g (approx. 6 g with z-axis) plus connector plug ) one elobau cycle corresponds to one oscillation of the joystick in all four directions under load (see adjacent figure) 2) third axis above handle, see figure below 3) connector is not sealed Chemical resistance + gear oil + motor oil + diesel + biodiesel + battery acid (conditional) + cleaning agent + gasoline + coolant + portable liquids J Version.4 Page 4 of
Color Standard grip Upper part Signal Black RAL004 Lower part Signal Black RAL004 Grip with push button Upper part Signal Black RAL004 Lower part Signal Black RAL004 Button cap Signal Black RAL004 Grip with z-axis Upper part Graphite Grey RAL7024 Lower part Signal Black RAL004 Key electrical data Joystick base Operating voltage Output signal Current consumption Load resistance Center position Reverse connection protected Output signal delay 4.5...5.5 VDC - 0.5...4.5 VDC - 0.5...4.5 VDC semi-redundant* - 0.5...4.5 VDC redundant max. 0 ma per signal input (40 ma; redundant) > 20 kω 2.5 V typical yes approx. 3 ms * The semi-redundant version features a common voltage supply z-axis ± 30 ± 30 Operating voltage Output signal Current consumption Load resistance Center position Reverse connection protected Output signal delay 4.5...5.5 VDC - 0.5...4.5 VDC - 0.5...4.5 VDC semi-redundant* max. 0 ma (20 ma; semi-redundant) > 20 kω 2.5 V typical yes approx. 3 ms J Version.4 Page 5 of
Push button Switching voltage Switching current Switching power Contact form 48 V AC / DC 0.3 A / DC 5 W / VA - N.O. (normally open) - Namur wiring Wiring Joystick base analog ratiometric Signal outputs of redundant and semiredundant outputs are always opposite. Joystick base analog ratiometric semi-redundant Joystick base analog ratiometric redundant Analog standard z-axis semi-redundant Push buttons N.O. (normally open) contact Namur wiring J Version.4 Page 6 of
Connection type Standard version 6-PIN Molex-Micro-Fit 3.0 43025-600 connector, view A (page 2) Joystick module Joystick module semi-redundant Joystick module redundant 2 2 2 2 Push buttons N.O. (normally open) contact / Namur wiring z-axis z-axis semi-redundant J Version.4 Page 7 of
Fax: +4 (0) 756 70-00 E-Mail: info@elobau.de Specifications of your J Joystick J.6AA0... ZA ZH Grip with z-axis Output signal z-axis analog Output signal z-axis semi-redundant TN TS Grip with push button Namur wiring N.O. (normally open) K- Grip without additional function Standard grip Assembly type A = Instl. from below, screw conn. from above B = Instl. from below, screw conn. from below C = Instl. from above, screw conn. from above 0 = multi-axial Actuation A = no detent End positions x-/ Output signal 6 = analog 0.5..4.5 VDC ratiometric Electronics A = analog H = analog semi-redundant redundant R = analog redundant J Version.4 Page 8 of
Fax: +4 (0) 756 70-00 E-Mail: info@elobau.de Your product enquiry Quantity Batch size Name / first name Company Address Postal code / town Country E-Mail Notes, questions, other J Version.4 Page of