DANLERS PIR OCCUPANCY SWITCHES CEFLPIR Neat and unobtrusive, flush mounted for suspended or plasterboard ceilings. 2 metre lead for ease of installation. 6 amps, most types of load. CEFLPIR 12V and 24V variants Versions of CEFLPIR can also be supplied with 12 volt or 24 volt supply. Versions of CEFLPIR can also be supplied with volt free output (12VVF) or (24VVF) supply. PLEASE SPECIFY A.C OR D.C. SUPPLY CEFLPIRSV As CEFLPIR except has short visit mode and exit functions to reduce the time lag duration when used in combination with a momentary wall switch. CESFPIR Surface mounted (square) for solid ceilings. Hard wired version. Can be mounted on a square pattress box. 6 amps, most types of load. CESFPIRIP66 IP66 rated enclosure. Surface mounted for solid ceilings. Hard wired version. 6 amps, most types of load. CESFPIRSV As CESFPIR except has short visit mode and exit functions to reduce the time lag duration when used in combination with a momentary wall switch. CESRPIR Surface mounted (round) for solid ceilings. Hard wired version. Can be mounted directly on solid ceilings or onto a mounting box. 6 amps, most types of load. CESRPIRSV As CESRPIR except has short visit mode and exit functions to reduce the time lag duration when used in combination with a momentary wall switch. PIR Switches with Short Visit and Exit Modes Benefit from manual intervention (short time lag) when used in combination with a momentary switch. CEFLPIRSV Ceiling flush mounted CESFPIRSV Ceiling surface - square CESRPIRSV Ceiling surface - round Round Surface Mounted PIR Switches CESRPIR PIR Occupancy Switch CESRPIRSV Short Visit PIR Switch CESRAPIR PIR Absence Switch CESRAPIRSD PIR Switch/Dim Control CEFLPPIR For suspended or plasterboard ceilings. With plug suitable for CESO or CESOSQ ceiling socket. Comes with 2m lead. CEFLPIRSEALED Splash-proof version of CEFL PIR, suitable for shower rooms. 6 amps, most types of load. Comes with 2m lead. CEDR6P Can be pointed in any direction. 6 amps, most types of load. Requires ceiling socket (CESO or CESOSQ). CEFLPIR10A Suitable for switching up to 10 amps (2500W), most types of load. Comes with 2m lead. CELO For solid ceilings. Plug-in version. 6 amps, most types of load. Also requires a ceiling socket (CESOSQ or CESO). CEDR6PLR Long range for corridors or aisles. 25m range. 6 amps, most types of load. Requires ceiling socket (CESO or CESOSQ). WACEPIR For plaster depth (16mm) wall box. 3 wire connections. 6 amps, most types of load. WAPIR 6 amps, most types of load. 16mm wall box. No neutral wire needed. Override off switch. Min. load 40W resistive. GREUWPIR5E (Visible adjustment spindles) GREUWPIR5X (Concealed adjustment spindles) Suitable for wall or ceiling mounting onto Eurodata plates. 5m range. 6 amps, most types of load. 25 x 50mm size, requires 35mm wall box. GREUWPIR10E (Visible adjustment spindles) GREUWPIR10X (Concealed adjustment spindles) Suitable for ceiling mounting onto Eurodata plates for use in circulation areas where significant movement is likely. 10m range. 6 amps, most types of load. 25 x 50mm size, requires 35mm back box. 142 CONTROLS 2016
BATTEN MOUNTED PIR OCCUPANCY SWITCHES BATTEN MOUNT PIR OCCUPANCY SWITCHES with Intelligent Photocell With DANLERS Intelligent Photocell calibration procedure for additional energy saving. Ideal for areas with natural daylight. Ideal for mounting onto the end of lighting battens via 20mm knock out. Adjustable photocell 100-3000 lux. Photocell status indicator. Switches up to 10 amps resistive, 6 amps fluorescent (switch start). Come with 1 metre wire tails. BMINTPIR5M - 5m detection range. BMINTPIR10M - 10m detection range BMINTPIRRH - Reduced height range. BMINTPIRSP - Spot detection range. BATTEN MOUNT PIR OCCUPANCY SWITCHES with Active Photocell With Active photocell. Ideal for areas with no or very little natural light Ideal for mounting onto the end of lighting battens via 20mm knock out. Adjustable photocell. Switches up to 10 amps resistive, 6 amps fluorescent. 1 metre wire tails. BMPIR5M - 5m detection range. BMPIR10M - 10m detection range BMPIRRH - Reduced height range. BMPIRSP - Spot detection range. BMEXPIR Ideal for mounting onto the end of lighting battens via 20mm knock out. IP66 rated enclosure, ideal for interior or exterior use. Built-in adjustable photocell and time lag. Switches up to 6 amps, most types of load. Comes with 1 metre wire tails. PIRS WITH DAYLIGHT LINKED DIMMING PIR OCCUPANCY SWITCHES WITH LOWER ILLUMINANCE SWITCHING Brings on lights only when an area is occupied. Automatically dims lights according to ambient light level, to maintain constant brightness of between 100 and 1000 lux (adjustable). For suspended or plasterboard ceilings. Switches up to 6 amps of fluorescent lamps. CEFLPIRDD10VDC: Controls up to twenty 1-10V d.c. dimmable ballasts. CEFLPIRDDDSI Controls up to 20 DSI dimmable ballasts. CEFLPIRDD10VDC CEFLPIRDDDSI CEFPLL10VDC Neat and unobtrusive, flush mounted for suspended or plasterboard ceilings. 2 metre lead for ease of instalation. Brings on lights to full value only when an area is occupied. Automatically switches ballast to reduced, light level (adjustable) when not occupied. Ideal for safety and security in corridors, toilet blocks, thoroughfares and so on. Controls up to twenty 1-10V d.c. dimmable ballasts. CEFPLL10VDCSEAL Splash-proof version of CEFPLL10VDC, suitable for interior damp areas such as underground car parks, toilet blocks etc. CESPLL10VDC Surface mounted for solid ceilings. Hard wired version. Can be mounted on a square pattress box. Brings on lights to full value only when an area is occupied. Automatically switches ballast to reduced, light level (adjustable) when not occupied. Ideal for safety and security in corridors, toilet blocks, thoroughfares and so on. Controls up to twenty 1-10V d.c. dimmable ballasts. CESPLL10VDCIP66 IP66 rated version of CESPLL10VDC, suitable for damp areas such as underground car parks, underpasses etc. MICROWAVE SWITCHES ANCILLARY PRODUCTS WAOSW CESO CESOSQ CESL CE2SL CESO CESO SQ Wall mounted override switch. For use with DANLERS PIR Occupancy switches and ControlZAPP devices to override automatic settings Round ceiling socket, required for CEDR6P or CEDR6PLR. Mounts on a BESA box. Square ceiling socket, required for CELO. Mounts on a square pattress box. Ceiling socket with slave relay. 6 amps max. Ceiling socket with double slave relay. 6 amps max. (each circuit). CESL CE2SL CONTROLS 2016 143
PIR ABSENCE SWITCHES For energy saving on lighting in offices, factories, etc. Adjustable lux level. Switches up to 6 amps of fluorescent load. CEFLAPIR Flush mounted absence switch for suspended or plasterboard ceilings. Hard wired version. 2 metre lead for ease of instalation. 6 amps, most types of load. CESFAPIR Surface mounted absence switch for solid ceilings. Hard wired version. Can be mounted on a square pattress box. 6 amps, any type of load. CESRAPIR Surface mounted round absence switch for solid ceilings. Hard wired version. Can be directly on solid ceilings or onto a range of different mounting boxes. 6 amps, any type of load. CEFLAPIRSD For switching / dimming (with suitable ballast and retractable wall switch - not supplied). Flush mounted absence control for suspended or plasterboard ceilings. Hard wired version. 2 metre lead for ease of instalation. 6 amps, most types of load. CESFAPIRSD For switching / dimming (with suitable ballast and retractable wall switch - not supplied). Surface mounted absence control for solid ceilings. Hard wired version. Can be mounted on a square pattress box. 6 amps, any type of load. CESRAPIRSD For switching / dimming (with suitable ballast and retractable wall switch - not supplied). Surface mounted round absence control for solid ceilings. Hard wired version. Can be directly on solid ceilings or onto a range of different mounting boxes. 6 amps, any type of load. PHOTOCELL SWITCHES CEFLAPIR CEFLAPIRSD CESRAPIR CESRAPIRSD CESFAPIR CESFAPIRSD For energy saving on lighting in offices, factories, etc. Adjustable lux level. Switches up to 6 amps of fluorescent load. CEFLPH Flush mounted, hard wired photocell switch. Switches on and off automatically CEFLPHRE Flush mounted, hard wired photocell switch. Re-set type: switches off automatically and on by operating a manual wall switch CEPHNO Surface mounted, plug-in photocell switch. Switches on and off automatically CEPHRE Surface mounted, plug-in photocell switch. Re-set type: switches off automatically and on by operating a manual wall switch CESOSQ Square ceiling socket. Mounts on a square pattress box. BMINTPH Intelligent Photocell calibration. Ideal for mounting onto the end of lighting battens via 20mm knock out. Adjustable photocell 100-3000 lux. Photocell status indicator. Switches up to 6 amps of most types of load. 1 metre wire tails. BMEXPH Ideal for mounting onto the end of lighting battens. IP66 rated enclosure, ideal for interior or exterior use. Built-in adjustable photocell. Switches up to 6 amps. 1 metre 3-core flex. CEFLPH CEFLPHRE CEPHNO CEPHRE BMINTPH BMEXPH CONTROLZAPP - PROGRAMMABLE LIGHTING CONTROLS ControlZAPP uses a freely downloadable APP to configure and change functions including switching or dimming settings, set schedules and profiles via your mobile phone or tablet (Android 4.3 or later). Remotely configured by BLUETOOTH SMART communications Scheduling function so different control functions can be programmed to occur at different times of day or different days of the week Accurate sunset / sunrise prediction times based on location Integral REAL TIME clock so functions happen EXACTLY when you want Version suitable for mains switching (100-260VAC) Versions for dimming DALI ballasts or 1-10VDC ballasts UK MANUFACTURED - 5 YEAR WARRANTY MOBILE PHONE FOR ILLUSTRATIVE PURPOSES ONLY CZCEFLP CZCEFLPVF CZCEFLPDALI CZCEFLPDALIVF DALIPSU CZCEFLP10VDC CZCEFLP10VDCVF Programmable, flush mounted control. Suitable for mains switching. Up to 10A resistive, 6A fluorescent, 3A LED and transformer loads. Programmable, flush mounted control. Volt free version. Suitable for switching a secondary signal rather than supply voltage. Programmable, flush mounted control for DALI ballasts. Can control up to 20mA (ie. 20 ballasts at 1mA). May require DALI PSU. Programmable, flush mounted control for DALI ballasts. Volt free version. Suitable for switching a secondary signal rather than supply voltage.may require additional DALI Power Supply Unit. DALI Power Supply Unit for use with CZCEFLPDALI and other DALI controls. Rated at 40mA. Programmable, flush mounted control for 1-10VDC ballasts. Can control up to 20mA (ie. 20 ballasts at 1mA). Programmable, flush mounted control for 1-10VDC ballasts. Volt free version. Suitable for switching a secondary signal rather than supply voltage. 144 CONTROLS 2016
DAYLIGHT LINKED DIMMERS Automatically dim lights according to ambient light level, to maintain a constant brightness of between 100 and 1000 lux (adjustable). For suspended or plasterboard ceilings. CEFLPHDD10VDC On/off switching and dimming. Controls dimmable ballasts with 1-10V d.c. input (up to 20mA) CEFLPHDDDSI On/off switching and dimming. Controls up to 10 DSI dimmable ballasts CEFLDD10VDC Dimming only. Controls dimmable ballasts with 1-10V d.c. input (up to 20mA) CEFLPHDD10VDC CEFLDD10VDC MANUAL HIGH FREQUENCY DIMMERS CEFL HDD DSI Push on, push off, with rotary dimming control DP1D 10VDC SB For one or two dimmable ballasts with 1-10V d.c. control DP1D 10VDC MB For several dimmable ballasts with 1-10V d.c. control (up to 20mA) DP1D DSI For several dimmable ballasts with DSI input (up to 20 DSI ballasts) DSSGD MK 10VDC Module for MK Grid Plus for several dimmable ballasts with 1-10V d.c. control (up to 20mA) DSSGD CB 10VDC Module for Crabtree grid for several dimmable ballasts with 1-10V d.c. control (up to 20mA) DSSGD EU 10VDC Module for Eurodata plates for several dimmable ballasts with 1-10V d.c. control (up to 20mA) Wire-free remote control senders HASE12RFC HASE2RF PLPR1RF WASE1RFWHI WASE2RFWHI WASE4RFWHI SLSE1RFSO DP1D 10VDC SB DP1D 10VDC MB DP1D DSI OUTDOOR SECURITY SWITCHES NEW DESIGNS WITH IP66 ENCLOSURES. Switch up to 6 amps of tungsten or 4 amps of fluorescent. DUSW NEW DESIGN: Dusk Switch. Switches on at dusk and off after a chosen period (2 to 16 hours, adjustable). Adjustable lux level. COPD NEW DESIGN: Outdoor PIR switch. Detects someone approaching and switches on lights. Built-in adjustable photocell and time lag. TWSW NEW DESIGN: Twilight Switch. Switches on at dusk and off at dawn. Adjustable lux level. TWSWINT NEW PRODUCT: Twilight Switch with Intelligent photocell. Switches on at dusk and off at dawn. Adjustable lux level. DUSW TWSW TWSWINT RADIO REMOTE CONTROLS Hand held remote control sender. Switches or dims on 12 channels. (NEW) Key fob remote control sender. Switches or dims on 2 channels. One channel, radio remote control plug-in programmer (NEW) One channel, matt white finish (NEW DESIGN) Two channel, matt white finish (NEW DESIGN) Four channel, matt white finish (NEW DESIGN) One channel slave sender, used with a plug-in DANLERS control eg. a PIR switch Radio remote control receivers WACERFS Remote mounted, hard wired receiver switch. Up to 6 amps load (1 amp fluorescent). CEFLRFS Remote ceiling flush mounted, hard wired switch. Up to 6 amps load (1 amp fluorescent). CEVORFS Remote ceiling void mounted, hard wired switch. Up to 6 amps load (1 amp fluorescent). CERFS6A CEVORFS6A DINRFS PORFS8A EXRFS WACERF2S WACERFD250W CEVORFD250W CERFD10VDCMB CERFD500WGT PORFD250W Remote mounted, plug-in receiver switch. Up to 6 amps load (6 amp fluorescent). Plugs into any of the sockets below. Remote mounted, hard wired receiver switch. Up to 6 amps load (6 amp fluorescent). Remote mounted, DIN rail receiver switch. Up to 6 amps load (6 amp fluorescent). Adapter socket receiver switch with mains plug and socket. 8 amp resistive or 1 amp fluorescent load. Outdoor mounted weatherproof receiver switch. Up to 6 amps load (1 amp fluorescent). Blind/motor control receiver. Twin actuator switch. Remote mounted, hard wired receiver dimmer switch. Up to 250W resistive or dimmable electronic transformer loads. Remote ceiling void mounted, hard wired receiver dimmer switch. Up to 250W resistive or dimmable electronic transformer loads. Ceiling build-in RF dimmer. 1-10VDC multiple ballast. Up to 20mA. Ceiling build-in RF dimmer. Up to 500W resistive or dimmable electronic transformer loads. Adapter socket RF receiver dimmer with mains plug and socket. Up to 250W resistive or dimmable electronic transformer loads. DSSGD MK 10VDC DSSGD CB 10VDC DSSGD EU 10VDC COPD DANLERS radio remote controls are for the remote control switching or dimming of lighting or other loads. A receiver switch or receiver dimmer is wired into the existing circuit to control the connected load. The sender signals can pass through walls, so the receivers can be mounted out of sight, if desired. Inside a typical building the receivers can work at an approximate range of 30-50 metres. In free air the range is approximately 100-150 metres. Each button on each sender sends a unique coded signal. Easily programmable for simple or more complex control set-ups. HASE12RFC WASE1RFWHI CEVORFS, CEVORFD250W HASE2RF WASE2RFWHI PORFS8A, PORFD250W WASERFS, WASERFD250W CEFLRFS SLSE 1RFSO CONTROLS 2016 145
DSSGDCB400W DQDGDCB400W SSGSCB RESLOADE DSS2D250W SS2SL 1 gang Rotary and Push Dimmers (not 1000W) 1 gang 1000W Rotary and Push Dimmers 4 gang Rotary and Push Dimmers DSSGDMK400W DQDGDMK400W SSGSMK DSSGDEU400W DQDGDEU400W SSGSEU DSS1D250W DSS1D400W SS1SL DPDLED 2 gang Rotary and Push Dimmers 3 gang Rotary and Push Dimmers Quiet Grid Dimmer Modules (trailing edge) Suitable for most mains dimmable LED lamps and fittings and mains halogen lamps. Multi point dimming using the matching slave switches DQDGDMK400W DQDGDCB400W DQDGDEU400W RESLOADE DIMMERS Quiet dimmer module for MK Grid Plus, 40-400W, multi-way switching and dimming. Quiet dimmer module for Crabtree grid, 40-400W, multi-way switching and dimming. Quiet dimmer module for Eurodata plates, 40-400W, multi-way switching and dimming. Load resistor for use with non-resistive loads such as mains dimmable LED lamps etc Soft Start Dimmers (leading edge) For tungsten, mains halogen or dimmable low voltage loads Soft start - prolongs bulb life Lights can be switched and dimmed from several locations using the matching slave switches Suitable for dimming mains halogen (e.g. GU10) lamps, without the need for derating. DSS1D250W 1 gang, 40-250W (resistive), multi-way switching and dimming. DSS1D400W 1 gang, 60-400W (resistive), multi-way switching and dimming. DSS2D250W 2 gang, 40-250W per gang (resistive), multi-way switching and dimming. DSSGDMK400W Dimmer module for MK Grid Plus, 40-400W, multi-way switching and dimming. DSSGDCB400W Dimmer module for Crabtree grid, 40-400W, multi-way switching and dimming. DSSGDEU400W Dimmer module for Eurodata plates, 40-400W, multi-way switching and dimming. Slave switches for DANLERS Soft start dimmers and Quiet grid dimmer modules SS1SL 1 gang slave switch, for use with soft start dimmers. SS2SL 2 gang slave switch, for use with soft start dimmers. SSGSMK MK Grid Plus module slave switch, for use with soft start dimmers. SSGSCB Crabtree grid module slave switch, for use with soft start dimmers. SSGSEU Eurodata module slave switch, for use with soft start dimmers. NEW Rotary and Push LED Dimmers (leading edge) Suitable for many dimmable LED lamps and fittings Adjustable spindle to specify minimum dim level to eliminate lamp instability DPDLED Dimmer module, 1 or 2 way push switching, for retro-fitting onto many existing dimmer plates DP1DLED 1 gang, 250W max. 1 or 2 way push switching, rectangular plate DP2DLED 2 gang, 250W max. per gang, 1 or 2 way push switching. DP3DLED 3 gang, 250W max. per gang, 1 or 2 way push switching, rectangular plate DP4DLED 4 gang, 250W max. per gang, 1 or 2 way push switching, rectangular plate Rotary and Push Dimmers (leading edge) Suitable for dimming mains halogen (e.g. GU10) lamps, without the need for derating. DR1D250W 1 gang, 40-250W, 1 way rotary switching. DR1D400W 1 gang, 60-400W, 1 way rotary switching. DR2D250W 2 gang, 40-250W per gang, 1 way rotary switching. DP1D250W 1 gang, 40-250W, 1 or 2 way push switching. DP1D400W 1 gang, 60-400W, 1 or 2 way push switching. DP1D630W 1 gang, 60-630W, 1 or 2 way push switching. DP1D1000W 1 gang, 60-1000W, 1 or 2 way push switching, rectangular plate DP2D250W 2 gang, 40-250W per gang, 1 or 2 way push switching. DP3D250W 3 gang, 40-250W per gang, 1 or 2 way push switching, rectangular plate DP4D250W 4 gang, 40-250W per gang, 1 or 2 way push switching, rectangular plate For dimmable (wire-wound or electronic) transformers DP1D250WI 1 gang, low voltage, 60-250W, 1 or 2 way push switching. DP1D400WI 1 gang, low voltage, 60-400W, 1 or 2 way push switching. DP1D630WI 1 gang, low voltage, 60-630W, 1 or 2 way push switching, rectangular plate. DP2D160WI 2 gang, low voltage, 40-160W per gang, 1 or 2 way push switching. For dimmable electronic transformers only DP1D250WIET 1 gang, low voltage, 40-250W, 1 or 2 way push switching. DP1D400WIET 1 gang, low voltage, 60-400W, 1 or 2 way push switching. DP1D630WIET 1 gang, low voltage, 60-630W, 1 or 2 way push switching. DP1D1000WIET 1 gang, low voltage, 60-1000W, 1 or 2 way push switching, rectangular plate. DP2D250WIET 2 gang, low voltage, 40-250W per gang, 1 or 2-way push switching. DP3D250WIET 3 gang, low voltage, 40-250W per gang, 1 or 2-way push switching, rectangular plate. DP4D250WIET 4 gang, low voltage, 40-250W per gang, 1 or 2-way push switching, rectangular plate. L E D QUIET O P E R AT I O N MULTI POINT MULTI POINT L E D 146 CONTROLS For the full DANLERS product catalogue, please contact your local 2016 branch
TIME LAG SWITCHES TLSW10 TLSW10ILM TLSWA20 TLSWA20ILM TLSWA120 TLSWA120ILM GRTLMKFWH Adjustable time lag, 1 to 10 minutes. No neutral wire needed. Switch up to 6 amps of most types of load, incl. fluorescent lights. Minimum load 40W resistive. As TLSW 10 but with Illuminated push button. Adjustable time lag, 2 to 20 minutes. Needs neutral wire. Switch up to 6 amps of any type of load, including fluorescent lights. As TLSW A20, but with illuminated push button. Adjustable time lag, 12 to 120 minutes. Needs neutral wire. Switch up to 6 amps of any type of load, including fluorescent lights. As TLSW A120, but with illuminated push button. Plated time lag switch with integral 6A rated fused spur. Adjustable time lag - 1 mins to 2 hrs. Plated Time Lag Switches Plated Time Lag Switches (ILM) All DANLERS grid time lag modules switch up to 6 amps of any type of load, including fluorescent lights. GRTLMK For MK Grid Plus. Adjustable time lag - 2 mins to 2 hrs. No neutral needed. Min load 2W resistive. GRTLMKILM GRTLMKILM as GRTLMK but with illuminated push button. GRTLCB For Crabtree grid. Adjustable time lag - 2 mins to 2 hrs. No neutral needed. Min load 2W resistive. GRTLCBILM GRTLCBILM as GRTLCB but with illuminated push button. GRTLEU For Eurodata plates. Adjustable time lag - 2 mins to 2 hrs. No neutral needed. Min load 2W resistive. GRTLEUILM GRTLEUILM as GRTLEU but with illuminated push button. Grid Time Lag Switches Grid Time Lag Switches (ILM) GRTLAMK GRTLAMKILM GRTLACB GRTLACBILM GRTLAEU GRTLAEUILM For MK Grid Plus. Adjustable time lag - 2 mins to 2 hrs. Needs neutral wire. GRTLAMKILM as GRTLAMK but with illuminated push button. For Crabtree grid. Adjustable time lag - 2 mins to 2 hrs. Needs neutral wire. GRTLACBILM as GRTLACB but with illuminated push button. For Eurodata plates. Adjustable time lag - 2 mins to 2 hrs. Needs neutral wire. GRTLAEUILM as GRTLAEU but with illuminated push button. Plated Slave Switch, 1 gang Plated Slave Switch, 2 gang Slave switches for use with square plated DANLERS Time lag switches and DANLERS 2 wire Grid time lag switches. SS1SL 1 gang slave push button SS2SL 2 gang slave push button SSGSMK Slave switch, MK Grid Plus module SSGSCB Slave switch, Crabtree grid module SSGSEU Slave switch Grid Slave Switches EXTLSW16A EXTLSW EXTLSW16A Exterior time lag switch, IP66 rating. Adjustable time lag, 2 to 20 minutes. Switch up to 6 amps (1.5kW) of any type of load, including fluorescent lights. Exterior time lag switch, IP66 rating. Adjustable time lag, 2 to 20 minutes. Switch up to 16 amps (4kW) of lighting and heating loads, incl. fluorescent lights EXTLSW GRTLMKFWH HVAC CONTROLS WAPIRTH WAPIRTHX WAPIRTC WAPIRTCX PIR/Thermostat Control, for electric heaters. Person detector and adjustable thermostat switch. Up to 3kW resistive load. WAPIRTHX - As WAPIRTH but with hidden thermostat adjustment. PIR/Thermostat Control, for cooling. Person detector and adjustable thermostat switch. Up to 3kW resistive load. WAPIRTCX - As WAPIRTC but with hidden thermostat adjustment. WAPIRTH / WAPIRTHX WAPIRTC / WAPIRTCX MULTI SELECTABLE TIME LAG SWITCHES 4 advanceable time options. Switches on manually, switches off automatically. Up to 13 amps. TLSWHB Heating boost switch. Timings: 1/4, 1/2, 1 and 2 hrs. TLSWHB1246 Heating boost switch. Timings: 1, 2, 4 and 6 hrs. TLSWMS Multi-selectable time lag switch. Timings: 1/4, 1/2, 1 and 2 hrs. TLSWMS1246 Multi-selectable time lag switch. Timings: 1, 2, 4 and 6 hrs. TLSWACT Air-conditioning time-on switch. Timings: 1/4, 1/2, 1 and 2 hrs. TLSWACT1246 Air-conditioning time-on switch. Timings: 1, 2, 4 and 6 hrs. Heater Boost Switches Multi Selectable Time Lag Switches and Air Conditioning Time on switches FASP Fan Speed Control. 1 or 2 way, push on/off switch with rotary speed control. 40-250W. FASP CONTROLS 2016 147