Dosimat feeder Cost-effective system Extractio/proportioig of sticky/abrasive ad coarse materials i oe uit OLie calibratio
Mai features Robust desig. Weigh feedig based o apro ad/or rubber belt coveyors. Less tha +/-0.5 deviatio from omial feed rate. Feeder operatio ot affected by rubber belt tesioig. Automatic adjustmet for variatios i bulk desity. Frequecy regulated AC or hydraulic drive. Figure 1. Rubber belt coveyor Dosimat feeder with dual drive Applicatio The Dosimat feeder is a accurate gravimetric proportioig device for bulk materials such as slag, limestoe, clay, gypsum, pozzolaa ad cemet cliker. The feeder extracts the materials from the feed bi ad proportios them i oe operatio. See Figure 3. A costat feed rate is maitaied by the Dosimat cotroller. Two or more feeders operatig i parallel, as show i Figure 7, are cotrolled so that the overall feed rate remais costat ad each feeder provides a cosistet share of the total feed. Desig The Dosimat feeder cosists of a suspesio frame, a statioary chute, a movable chute, a coveyor frame, a rubber or apro coveyor, a drive statio, a load cell arragemet ad a discharge casig. The suspesio frame icorporates a rod gate to eable closig the feed bi outlet for maiteace or tare weighig purposes. The rods may be activated by a peumatic hammer. See Figure 2. The side sectio, the movable chute ad the coveyor frame are pivotally suspeded from the statioary chute via two blade sprigs o either side ad two wire straps close to the discharge ed. Materials Hadlig Figure 2. Rod gate activated by peumatic hammer
Figure 6. Cotrol of Dosimat feeder Figure 7. Dosimat feeders i parallel operatio The restrictio plate o the movable chute esures a cosistet material layer o the coveyor. Two load cells mouted betwee the suspesio frame ad the wire straps moitor the load of material ad the tare load of the coveyig system. See Figure 10. The sigals from the load cells pass to the Dosimat cotroller. Rubber belt coveyors are cleaed by a scraper blade fitted at the discharge ed of the coveyor ad apro coveyors by a separate spillage scraper flaged to the discharge casig. The spillage scraper is optioal. The discharge casig is floor mouted ad has o mechaical cotact with the coveyor frame. As a optio, the discharge casig may have a peumatically activated flap gate for check weighig purposes. The coveyor is drive by a shaft mouted gear uit ad as AC motor with frequecy coverter speed regulatio. See Figure 8. A hydraulic drive statio is optioal. The motor speed is moitored by a ecoder. Dosimat feeders with coveyor width up to 1000 mm are equipped with a sigle drive statio while feeders with wide coveyors have dual drive statios. See Figure 1. Dosimat cotroller The Dosimat cotroller cabiet cotais the cotrol uit, auxiliary electrical equipmet, ad operator pael for detailed moitorig ad cotrol of feeder Figure 8. AC frequecy cotrolled drive statio ad sectioalized apro scraper Figure 9. Hydraulic pump arragemet for belt tesioig Figure 10. Load cell arragemet
Dimesios Dosimat feeder A2 AxB C ExF H G A2-80x3,4 990x990 3400 560x1400 2755 800 A2-130x3,4 1240x1390 3400 560x2000 2755 1300 A2-200x3,5 1980x1980 3500 630x2500 3280 2000 Dosimat feeder R2 AxB C ExF H G R2-100x3,4 1240x990 3400 560x1800 2365 1000 R2-140x3,4 1390x1240 3400 560x2240 2365 1400 R2-180x3,4 1390x1590 3400 630x2500 2365 1800 1. Rod gate 2. Statioary chute 3. Chai lubricatio 4. Movable chute 5. Load cell arragemet Characteristics 6. Discharge casig 7. Apro belt 8. Drive uit 9. Rubber belt Dosimat feeder R2 Type A2 Type R2 80*3,4 130*3,4 200*3,5 100*3,4 140*3,4 180*3,4 Capacity, max, m 3 /h 185 440 815 150 320 535 Material size, max, mm 90 135 180 60 85 110 operatio ad a frequecy coverter for belt motor power. See Figure 6. Digital weighig amplifiers measurig the material load o the Dosimat coveyor ad, as a optio, the weight of the feed bi, are placed i field. Figure 11. Lubricatio system of apro coveyor roller chai The cotrol uit automatically regulates the coveyor speed based o material ad tare load to attai the desired feed rate. It also makes adjustmets for variatios i bulk desity. Automatic OLie calibratio of the Dosimat system ehaces feed accuracy ad product quality by reducig chemical variatios. This optio etails placig the feed bi o three load cells. Techical advatages All cotiuous weigh feeders are exposed to radom errors ad bias. The desig of the Dosimat feeder makes bias the domiat source of error ad this may be elimiated by OLie calibratio. The accuracy of cotiuous rubber belt weigh feeders is ormally cosidered sesitive to belt tesio. The Dosimat feeder equipped with a rubber belt coveyor has bee desiged to elimiated this sesitivity. Traditioally, cotiuous weigh feedig of coarse or sticky/ abrasive materials has required a two stage solutio cosistig of a apro extractor ad a weighig belt. The Dosimat feeder with apro coveyor is desiged to hadle such materials i a uique sigle stage operatio. The apro coveyor is more abrasio resistat tha the rubber belt ad the frictio betwee the apro plates ad the sticky materials esures smooth operatio. Side guards o the apro coveyor plates eable fully utilisig the etre width of the coveyor.
Figure 3. Raw material proportioig ad raw meal productio Figure 4. Dosimat feeder with rubber belt coveyor type R2 Figure 5. Dosimat feeder with apro coveyor type A2
F.L.SMIDTH & CO. : DENMARK, F.L.Smidth & Co. A/S, Vigerslev Allé 77, DK -2500 Valby, Copehage. Telex : 27040 flsco dk. Telephoe : +45-36- 18 10 00. Cemet Projects Divisio. Telex : 21028 flscpd dk. Telefax : +45-36 30 18 20. Products Divisio. Telex : 27040 flsco dk. Telefax : +45-31 17 47 24 Parts & Services Divisio. Telex : 27050 flssp dk. Telefax : +45-36 44 11 19. FULLER COMPANY : USA, Fuller Compay, 2040 Aveue C, Bethlehem, Pesylvaia, 18017-2188 Telegrams : colfuller, Telex : 173189, Telephoe: +1-610-264-6011. Telefax : 1-610-264-6170. From upgrades to complete plats F.L. Smidth supplies cuttigedge techology ad high efficiecy equipmet to the worldwide cemet idustry. Nearly a third of the world s cemet productio comes from plats ad machiery provided by F.L. Smidth. Workig from more tha 100 years experiece, F.L.Smidth masters all aspects of advaced process ad plat layout techology, assurig customers of low eergy cosumptio, high availability ad a quality ed product. Egieerig ad processes are adapted to idividual customer requiremets ad local coditios, whether it is a complete 10,000 tpd gree field cemet plat, a sigle machie uit or a cotrol system. Respodig to market eeds, the compay is stregtheig its focus o the three areas i which the cemet ad various mierals processig idustries look to F.L Smidth for leadership: Complete projects requirig process ad detailed plat layout kow-how, as well as practical operatioal experiece. Competitive ad reliable machies icorporatig the latest techological advaces. Spares ad timely services to assure customers of miimal iterruptios i operatio, thereby icreasig competitiveess ad profitability. For further details, please cotact F.L. Smidth at oe of the addresses : Data i this brochure is iteded for prelimiary project plaig oly. The maufacutrer reserves the right to modify equipmet details ad/or specificatios without otice. F.L.SMIDTH & FULLER SUBSIDIARIES AND REPRESENTATIVE OFFICES : AUSTRALIA, FULLER-F.L.SMIDTH (PACIFIC) PTY. LTD. Telephoe : +61-2-439-8177, Telefax : +61-2-436-3886. BRAZIL, F.L.SMIDTH COMERCIO E INDUSTRIA LTDA. Telephoe : +55-11-536-4177 Telefax : +55-11-5339612. CANADA, FULLER-F.L.SMIDTH CANADA LIMITED Otario : Telephoe : +1-416-284-8200. Telefax : +1-416-284-8348. Quebec : Telephoe : +1-514-489-9311. Telefax : +1-514-485-9188 CHILE, Idepedet Sales Office, Fuller-Traylor, Ic. Telephoe : +56-2-2344362, +56-2-2428693. Telefax : +56-2-2428694 GERMANY, F.L.SMIDTH-FULLER GMBH. Telephoe: +49-211-591-038. Telefax : +49-211-593-233 FRANCE, F.L.SMIDTH-FULLER S.A. Telephoe : +33-1-4944-6800. Telefax : +33-1-4308-5099, +33-1-4308-5188 INDONESIA, Mr. Ja Erdma, c/o P.T. Fajar Laksaa Sejahtera. Telephoe : +62-21-251-2738/ +62-21-251-2739 Telefax : +62-21-251-2738/ ITALY, F.L.SMIDTH & C.ITALIANA S.r.L. Telephoe : +39-35-468311. Telefax : +39-35-460838 JAPAN, FLS Japa Ltd. Telephoe : +81-3-35423403 Telefax : +81-3-35450701. MEXICO, FL.L.SMIDTH-FULLER MEXICO S.A. de C.V. Telephoe : +52-836-33150 Telefax : +52-836-33421 P.R. CHINA, F.L.SMIDTH & Co. A/S Telephoe : +86-1-5122288 ext. 1307, +86-1-5127777 Telefax : +86-1-5124693 REPUBLIC OF KOREA, Fuller Iteratioal, Ic. Telephoe : +82-2-776-2106, Telefax : +82-2-755-6524 SOUTH AFRICA, FULLER-F.L.SMIDTH (PTY) LTD. Telephoe : +27-11-806-3911 Telefax : +27-11-803-1408 SPAIN, F.L.SMIDTH & CIA ESPANOLA, S.A. Telephoe: +34-1-636-04-00. Telefax : +34-1-636-11-50 THAILAND, Mr. Aders Bech, c/o. Mitsiam Iteratioal, Ltd. Telephoe : +66-2-285-1020. Telefax : +66-2-285-1968-9. TURKEY, F.L.SMIDTH & CO. A/S. Liaiso Office. Telephoe : +90-212-251-13-31 Telefax : +90-212-251-62-82 UNITED KINGDOM, F.L.SMIDTH-FULLER LTD. Tele- Phoe : +44-81-686-2422. Telefax : +44-81-681-7229. LICENSEES/JOINT VENTURES: FRANCE, Ameco S.A. Telephoe : +33-89 65 52 11 Telefax : +33-89 65 56 24. USA, Ameco North America, Telephoe: +1-404-336-5030. Telefax: +1-404-336-5400 INDIA, Larse & Toubro Ltd. (Licesee). Cemet Machiery Divisio. Telephoe: +91-22-5781401. Telefax : +91-22-5783437 Fuller-K.C.P. Ltd (Joit Veture), Madras: Telephoe : +91-44-8276030, +91-44-8279393 +91-44-8272121. Telefax: +91-44-8279393 Bombay: Telephoe: +91-22-4942319. Calcutta: Telephoe : +91-33-4751764. Telefax : +91-33-747965. New Delhi: Telephoe: +91-11-3716873. Telefax : +91-11-3711360.