The WAGO Node integrates ancillary equipment into the Intelligent Touch Manager (itm) DCM601A71 with the use of DI, DO, AI and AO signals. It provides monitoring and control of non-daikin equipment via manual control, interlock, scheduling and remote access using itm touch screen or web access. Integration scheme WAGO Node Features Monitoring/Control of ancillary equipment: a) Digital Input b) Digital Output c) Analog Input d) Analog Output Interlock Function a) Creates interlocks among sensors (CO2, Humidity, Temperature), ancillary equipment, and/or indoor units at the itm. b) High/Low Limit Alarms configurable for CO2, Humidity, and Temperature. Schedule Function a) Up to 20 schedule events per day can be set for the ancillary equipment at the itm Web Access a) All the ancillary equipment can be monitored and controlled through web access function of the itm. Easy installation a) Din rail mount Standard width 1.38 (35mm)
System Capacity itm Management points limitation a) Up to 512 total contact points can be connected b) A total of 650 points which includes Daikin indoor unit groups and WAGO contact points can be connected c) Up to 30 nodes can be connected WAGO node points limitation d) Up to 120 contact points per node Up to 1640 ft. wiring length to the farthest WAGO node from the itm Specifications Basic Kit Part # Characteristics Image (dimension W x H x L) Bus Coupler (750-315/xxx-xxx 2 ) MODBUS (RS485) Communication, 24VDC input (2.01 x 2.56 x 3.94 ) Basic Kit (required for each Node 1 ) (Total width 4.45 ) 51291052 End Module (750-600) The module is used to terminate the internal bus of a Node. Fieldbus Connector (750-960) D-Sub male connector: 9 pin, 2 horizontal wire entries, one input and one output (0.47 x 2.52 x 3.94 ) 24 VDC Power Supply (787-712) Input voltage 110 240VAC, output voltage 24VDC @ 2.5A (1.97 x 3.62 x 5.35 ) Note: 1. A Maximum of 120 contacts can be connected to one node. 2. The part numbers may vary depends on versions.
750-479 3 I/O Module 1 Part Number Characteristics 2 Image (dimension W x H x L) 2 Channel DI 750-400 2 Channel Digital Input Module, 24 VDC, 3 power Digital 4 Channel Digital Input Module, 24 VDC, 2 power 4 Channel DI 750-432 Input 8 Channel DI 750-430 8 Channel Digital Input Module, 24 VDC, 2 power 750 513/000 2 Channel Digital Output Module, no power jumper 2 Channel DO Digital 001 contact Output 4 Channel Digital Output Module, 24 VDC, 2 power 4 Channel DO 750-504 750-454 2 Channel Analog Input Module, 4 20 ma, Differential Inputs, no power jumper contact 2 Channel AI Differential Measurement Input, no power jumper 2 Channel Analog Input Module, ± 10 VDC, contact Analog 750 461/020 000 2 Channel Analog Input Module, NTC 20k Ohm, no power jumper contact Input 4 Channel Analog Input Module, 4-20 ma, singleended, 2 power 750-455 4 Channel Analog Input Module, 0-10 VDC, singleended, 2 power 750-459 4 Channel AI 4 Channel Analog Input Module, NTC 20k Ohm/ 750-464/020-000 4 NTC 10k Ohm, configurable, 2 power jumper contacts (0.47 x 2.52 x 3.94 ) 2 Channel Analog Output Module, 4 20 ma, 2 750-554 power 2 Channel AO 2 Channel Analog Output Module, 0-10 VDC, no 750-550 Analog power jumper contact Output 4 Channel Analog Output Module, 4-20 ma, 2 750-555 power 4 Channel AO 4 Channel Analog Output Module, 0-10 VDC, 2 750-559 power 24 VDC Bus Power Supply Module, Required for use Internal System Power 750-613 after every 32 contact points connected in a node, 3 Supply power Passive Power Supply 750 602 24 VDC Power Supply Module, passive, 3 power Wiring Field Supplied 2-conductor Shielded copper cable 24AWG Up to 1640 ft.
* Note: 1. All sensors are field supplied. 2. A module with less power shall be placed after modules with more power. Otherwise, 750-602 is needed to supply power to the module with more power. 3. For 750-479 (2 Channel Ai ± 10 VDC), only range 0-10VDC can be used with itm. 4. 750-464/020-000 is not compatible with the bus coupler 750-315/000-002 (kit part number 51291052). Schematics Basic Kit - Part # 51291052 Bus Coupler (750-315) Connector (750-960) 24V DC Power Supply (787-712) End Module (750-600)
Wiring itm and WAGO node Wiring 24VDC Power supply
2 Channel Di 750-400 4 Channel Di 750-432 8 Channel Di 750-430 2 Channel Do 750-513/000-001 4 Channel Do 750-504
Error Error Shield Shield 2 Channel Ai (4-20 ma) 750-454 2 Channel Ai (± 10 VDC) 750-479 2 Channel Ai (20k Ohm) 750-461/020-000 4 Channel Ai (4-20 ma) 750-455 4 Channel Ai (0-10 VDC) 750-459 4 Channel Ai (NTC 10/20k Ohm) 750-464/020-000
2 Channel Ao (4-20 ma) 750-554 2 Channel Ao (0-10 VDC) 750-550 4 Channel Ao (4-20 ma) 750-555 4 Channel Ao (0-10 VDC) 750-559