Parts and Accessories Installation Instructions

Parts and Accessories Installation Instructions F 36 0 M Ericsson handsfree facility retrofit kit BMW 3 Series Saloon (E36/) LHD BMW 3 Series Coupé (E36/) LHD BMW 3 Series touring (E36/3) LHD BMW 3 Series Convertible (E36/C) LHD BMW 3 Series compact (E36/5) LHD Specialist and electrical knowledge required. Installation time approx. 3 hours, depending on the condition of the car and the equipment in it. Retrofit / Installation kit No. 8 6 0 05 86 Retrofit / Installation kit No. 8 6 0 06 69 Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69...Issue date: 07.000 Installation instructions No. 0 9 0 05 885

Table of contents Section Page. Important information for the installation of the Ericsson handsfree facility.... Preparations...3 3. Parts overview.... To install the telephone console (E36//3//C only)...6 5. To install the telephone console (E36/5 only)...8 6. To assemble the control module for the handsfree facility...9 7. Connection overview...30 8. Installation and wiring diagram...3 9. To install the holder for the mobile phone...33 0. To install and connect the wiring harnesses and switch module...3. To install the microphone (E36//3//C only)...36. To install the microphone (E36/5 only)...37 3. Coding and concluding work...38. Circuit diagram...39 Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885

. Important information for the installation of the Ericsson handsfree facility Only for use within the BMW dealer organisation. The Ericsson handsfree facility may only be installed by a specialist workshop that has the required special tools and manuals (servicing, repair, diagnostics, etc.). Ensure that the cables/lines are not kinked or damaged as you install them in the car. Additional cables/lines that you install must be secured with cable ties. Item numbers refer only to the parts overview, capital letters to the connection overview and small letters only to the texts next to the appropriate figure. The retrofit/installation kit contains a black telephone console. If a coloured telephone console is required it must be ordered separately using the electronic parts catalogue (EPC). Subject to technical modifications Tools and equipment required MoDIC III or DIS Set of Philips screwdrivers Set of straight slot screwdrivers Set of ring spanners Set of drill bits Angle cutter Cable lamp /inch socket set Drill Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/

. Preparations TIS instruction No. Conduct a short test. Disconnect the battery. 00... Remove the side trim on the left in the boot. Remove the rear seat bench and rear seat backrest. 5 0... Remove the instrument panel trim at the bottom left. Remove the footwell trim on the left. Remove the A pillar trim at the bottom left. Remove the door sill strip at the front left. 5 7 000 Remove the door sill strip at the rear left. 5 7 030 Remove the console from the handbrake lever. Remove the ashtray (E36/5 only). Remove the radio (E36/5 only). 65 030 Remove the clock or onboard computer (E36/5 only). 65 8 00 Remove the oddments box in the centre console (E36//3//C only). Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/3

3. Parts overview 3 5 6 7 8 9 0 3 5 6 7 8 E36 9 0 3 5 6 E36/5 7 8 9 30 33 3 3 F 36 00 M Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/

3. Parts overview Item Description Quantity 3 5 6 7 8 9 0 3 5 6 7 8 9 0 3 5 6 7 8 9 30 3 3 33 Mobile phone holder with connection cable Handsfree facility control module Screw M x 6 Washer.3 Nut M Selftapping screw with washer ST. x 6Z Spacer (for cars with footwell light only) Cable tie Cable tie Microphone Adapter wiring harness Basic wiring harness A and 3 A fuses Pin contact for switch module pin plug casing for switch module Switch module Shrink hose pin socket casing (supplied with switch module not needed) Retaining clip (Saloon, Coupé, touring and Convertible only supplied with telephone console) Selftapping screw ST3.9 x 9 (Saloon, Coupé, touring and Convertible only supplied with telephone console) Selftapping screw ST3.9 x 3 (Saloon, Coupé, touring and Convertible only supplied with telephone console) Selftapping screw ST.9 x 9.5 (Saloon, Coupé, touring and Convertible only supplied with telephone console) Speed nut 3.9 (Saloon, Coupé, touring and Convertible only supplied with telephone console) Holder (Saloon, Coupé, touring and Convertible only supplied with telephone console) Telephone console (Saloon, Coupé, touring and Convertible only supplied with telephone console) Cover (Saloon, Coupé, touring and Convertible only supplied with telephone console) Console for microphone (Saloon, Coupé, touring and Convertible only) Oddments box (Saloon, Coupé, touring and Convertible only) Cover (Saloon, Coupé, touring and Convertible only) Base for oddments box (Saloon, Coupé, touring and Convertible only) Telephone console (compact only supplied with telephone console) Selftapping screw ST. x 6 (compact only supplied with telephone console) FME connector for aerial connection 0 3 Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/5

. To install the telephone console (E36//3//C only) 9 c e d b a 3 9 F 36 05 M The precise position of the retaining clips (dimensions d and e) has a major bearing on how well the telephone console will fit on the centre console. Remove the Philips screws (c) from the top and side mounting for the cover trim (b). Place the speed nuts (3) on the retaining clips (9). Raise the cover trim (b) in the direction indicated by the arrow and push the retaining clips (9) between the cover trim (b) and the centre console (a). Dimension d = 30 mm Dimension e = 95 mm 9 0 Fit the holder () on the centre console (a) using the positioning lugs (see arrows) and secure it to the retaining clips (9) with the selftapping screws ST3.9 x 9 (0). a F 36 053 M 5 a F 36 05 M After correctly installing the holder () on the centre console, slide the telephone console (5) into the guide rail (a) and swing it upwards until the holes (in the telephone console and holder) line up. Secure the telephone console (5) to the holder () using selftapping screws ST3.9 x 3 (). The resulting stressing will considerably increase the load capacity and the stability of the BMW telephone console on the centre console. Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/6

. To install the telephone console (E36//3//C only) 6a Engage the cover (6) with the guides (6a) at the top in the telephone console (5), turn it downwards until the engagement pin locks and secure with the with selftapping screw ST.9 x 9.5 (). 6 5 F 36 055 M Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/7

5. To install the telephone console (E36/5 only) a a b Remove the Philips screws (a). Swing the cover trim (b) downwards. F 36 068 M b 3a Insert the retaining lug (3a) on the telephone console (3) between the cover trim (a) and the instrument panel (b). a 3 F 36 057 M c d c b 3 Align the telephone console (3) on the centre console (a) and the instrument panel (d). Press the cover trim (b) on to the instrument panel (d) and secure it with the Philips screws (c). Press the telephone console (3) on to the centre console (a) in the direction indicated by the arrow and secure it with a selftapping screw ST. x 6 (3). 3 a F 36 058 M Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/8

6. To assemble the control module for the handsfree facility 5 The figure shows the trim (a) on the E36/5, proceed accordingly on other models. The spacers (7) are only required for models with a footwell light (b). Remove the insulation mat in the installation area if necessary. 7 b 7 a Position the control module () as shown, mark the positions of the holes and drill them with a.5 mm drill bit. Secure the control module () with screws M x 6 (3), washers () and nuts M (5) and with the spacers (7) if necessary. 3 F 36 050 M Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/9

7. Connection overview A A B C C3 C B A B B3 B0 B9 C B5 B B8 C B7 C5 A3 B6 A A5 A6 C6 C7 D D D C C C0 C9 C8 F 36 0 M Item Description Cable colour/ Crosssection Connection location in the car A Adapter wiring harness A Black 8pin plug casing, X5* Branch B below the instrument panel on the left A White 6pin socket casing, X9* Not required tie back on the wiring harness A3 White 5pin socket casing, X* Handsfree facility control module below the instrument panel on the left A Angled pin pawl plug, 3.5 mm in diameter, X6* Handsfree facility control module below the instrument panel on the left, pawl socket with symbol for microphone A5 pin pawl plug, 3.5 mm in diameter, X7* Handsfree facility control module below the instrument panel on the left, pawl socket with symbol for speaker A6 White pin socket casing, X8* Handsfree facility control module below the instrument panel on the left B Basic wiring harness B Black 8pin socket casing, X5* Branch A below the instrument panel on the left B Black 6pin socket casing, X3 Black 6pin plug connector X3 below the instrument panel on the left B3 Black 6pin plug casing, X3 Black 6pin plug connector X3 below the instrument panel on the left B White pin socket casing, X* Switch module C in the A pillar at the bottom left B5 Black pin socket casing, X8507 Microphone in the oddments box in the centre console (E36//3/ /C) or next to the light switch in the instrument panel on the left (E36/5) The X designations marked with an asterisk (*) only apply for this overview and do not refer to the general aftersales service documents. Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/30

7. Connection overview Item Description Cable colour/ Crosssection Connection location in the car B6 Black 3pin socket casing, X3* Compensator in the boot on the left B7 Coaxial socket casing FME With FME connector to the aerial or compensator in the boot on the left B8 Coaxial socket casing FME Branch D of the holder for the mobile phone D B9 Fuse holder, P* Insert fuses as shown on the circuit diagram and insert in the free slot on the joint connector box under the instrument panel on the left B0 Terminal lug A6, X873 Earth post X873 under the instrument panel on the left C Switch module C Black pin plug casing Cut and connect the white pin plug casing to the switch module C (white/brown = pin / red/white = pin ) C Socket contact white/brown / 0.75 mm Not required C3 Socket contact red/white / 0.75 mm Not required C Blade terminal, 6.3 mm blue/white / 0.75 mm Cut and connect the white pin plug casing to the switch module C (pin ) C5 Blade terminal,.8 mm blue/brown / 0.75 mm Cut and connect the white pin plug casing to the switch module C (pin 3) C6 Blade receptacle,.8 mm yellow/white / 0.75 mm Speaker H58 in the footwell on the left C7 Blade receptacle,.8 mm yellow/brown / 0.75 mm Speaker H58 in the footwell on the left C8 Blade terminal,.8 mm yellow/red / 0.75 mm Disconnected cable from speaker H58 in the footwell on the left C9 Blade terminal,.8 mm yellow/brown / 0.75 mm Disconnected cable from speaker H58 in the footwell on the left C0 Black 3pin plug casing, X* For navigation system connection not required C Coding loops white and blue Only for installations with navigation system not required C Terminal lug A6, X873 brown / 0.75 mm Earth post X873 under the instrument panel on the left D Mobile phone holder D Black 0pin socket casing, X0* Control module for handsfree facility under the instrument panel on the left D Coaxial plug casing FME Branch B8 under the centre console for gearshift and selector lever The X designations marked with an asterisk (*) only apply for this overview and do not refer to the general aftersales service documents. Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/3

8. Installation and wiring diagram D B8 B D 0* B6 B7 A 6 F 36 08 M The figure shows the E36/, proceed accordingly on other models. The microphone (0*) is to be installed in the instrument panel on the left below the light switch on the E36/5, on the other models it is installed in the oddments box in the centre console.tie back excess cable lengths on the vehicle wiring harness. Secure the holder () for the mobile phone on the telephone console and lay branch D to the installation location of the control module () for the handsfree facility. Secure the control module () for the handsfree facility on the footwell trim on the left. Prepare the switch module (6) with the pin contacts supplied and the white pin plug casing and install it in the A pillar on the left and connect it. Connect the basic wiring harness B, connect branch B8 to branch D and lay branches B6 and B7 along the audio wiring harness into the boot on the left. Install and connect the microphone (0*): E36/5 in the instrument panel on the left under the light switch E36//3//C in the oddments box in the centre console. Connect the wiring harness A to the basic wiring harness B and the control module () for the handsfree facility and tie them back. Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/3

9. To install the holder for the mobile phone b 6 c d 6 e a f D D a 5 F 36 05 M DThe figure shows the telephone console (5) for the E36//3//C, proceed accordingly on the E36/5. When inserting the mounting plate (e) ensure that the threaded insert (f) is inserted. Depending on the design of the mobile phone, the extension piece from the installation kit may have to be inserted between the top (b) and bottom (a) parts of the holder (). Align the holder (a f) and mounting plate (e) on the cover (6) of the telephone console (5) and mark the positions of the holes. Drill the marked holes with a mm drill bit and secure the mounting plate (e) with selftapping screws ST.x6Z (6). Align the top part (b) on the mounting plate (e) and secure it with a screw (c) and washer (d). Insert the bottom part (a) in the top part (b) and press it in until it engages. It may be necessary to cut the centre console slight to ensure that branches D and D are not jammed as they pass through. Lay branch D to the installation location of the control module for the handsfree module in the footwell on the left. Lay branch D to the centre console near the gearshift or selector lever. Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/33

0. To install and connect the wiring harnesses and switch module C5 C Disconnect branches C, C and C3 with the dimension a = 50 mm from the switch module. Branches C, C and C3 are no longer required. Disconnect the blade terminals from branches C and C5, blue/white and blue/brown cables. Fit the remaining four cables on the switch module C with the pin contacts () and connect them to the plug casing (5) as follows: 5 C Cable colour Pin white/brown red/white blue/brown 3 blue/white a C3 C C F 36 03 M C8 7 C9 c b d 5 B C6 C7 Remove the footwell speaker (d) and disconnect the connection cables (b and c). Push the shrink hoses (7) on to branches C8 and C9, yellow/red and yellow/brown cables, connect branches C8 and C9 to the connection cables (b and c) and insulate them with the shrink hoses (7). Connect branches C6 and C7, yellow/white and yellow/brown cables, to the footwell speaker (d) and install the footwell speaker (d). Connect the white pin plug casing (5) on the switch module C to branch B. F 36 0 M B0 b C B A a Connect branches B0 and C to the earth post X873 (b). Disconnect the plug connector X3 (a) and connect it to branches B and B3. Connect branches B and A. Tie back the switch module C behind the footrest with cable ties and install the bottom A pillar trim. Branch A is not required tie it back on the wiring harness. B3 B A F 36 03 M Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/3

0. To install and connect the wiring harnesses and switch module 3 The F designations marked with an asterisk (*) are only valid for this installation and do not refer to the aftersales service documents. B9 F 36 06 M Insert fuses F* to F* (3) into the fuse holder B9 as shown in the following table: Fuse Slot Cable colour 3 A F* red/white and red/black 3 A F* red/white and red/yellow A F3* violet/white and violet/black Not occupied F* violet/white and violet/yellow Insert the fuse holder B9 into the free slot in the joint connector box on the A pillar on the left. A6 D A5 8 The figure shows the footwell trim on the E36/5, proceed accordingly for the other models. A3 A Connect branches A3, A, A5, A6 and D to the control module () and secure it with a small cable tie (8). Tie back surplus lengths of the cables and install the footwell trim. F 36 09 M Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/35

. To install the microphone (E36//3//C only) 9 7 Insert the console (7) for the microphone (0) with the cover (9) and base (30) in the oddments box (8). Remove the cigarette lighter and switch from the old oddments box and install them in the new oddments box (8). 0 B5 8 30 F 36 05 M Refer to the direction of the arrows when you install the microphone (0). Insert the assembled oddments box (8) into the centre console, connect branch B5 to the microphone (0) and press the microphone (0) into position. Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/36

. To install the microphone (E36/5 only) d 0 Refer to the direction of the arrows when you install the microphone (0). Unclip the trim, connect branch B5 to the microphone (0) and press the microphone (0) into the switch trim (d). F 36 07 M Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/37

Coding and concluding work No coding with DIS or MoDIC is required for this retrofit kit. Assemble the car again following the instructions to dismantle it in reverse order. Print out the error memory. Conduct a function test. Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/38

. Circuit diagram 6 5 3,0 GR/RT X3 GR/RT 0,5 WS/BR 0,5 WS/BR 0,75 SW/WS 6 N9 5 0,75 WS/RT/ GE ),5 VI/WS 3 X873,5 RT/WS X3,0 RT/WS 3A 3A F* F*,0 RT/WS 3,0 VI/WS 5 A F3* 6,0 VI/WS 7 8 X* P* X* 8 X86 0,5 BL 0,75 BR 0,5 RT/SW 0,5 VI/GE 0,5 VI/SW 3 X3* 0,75 GE/BR 0,75 GE/RT 0,75 GE/WS 0,75 GE/BR H58 0,75 WS/ BR 3 0,75 BL/ BR 0,75 BL/ WS A* 0,75 RT/ WS 0,5 WS 0,75 BL/SW 0,75 BL/BR 0,75 WS/BR X* ) 3 X* 0,5 RT/GE 0,5 RT/GE BR X873 B00 0,5 WS/BR BL/ BR BL/WS BR SW X8507 X873 0,5 BR N* 5 8 3 5 3 0 7 8 X5* GN SW SW GE/SW SW RT RT BR BR VI/WS GE/SW SW SW GN SW SW GN SW 0,5 RT A3* 3 X9* 6 5 X9* GE/SW SW 0,5 BR X* X7* X6* X8* X0* A* F 36 07 M Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/39

. Circuit diagram Legende zum Schaltplan A* Switch module A* Handsfree facility control module A3* Holder for mobile phone B00 Microphone for mobile phone F* 3 A fuse for compensator (terminal 30) F* 3 A fuse for handsfree facility control module (terminal 30) F3* A fuse for compensator (terminal R) H58 Footwell speaker, left N* Aerial for mobile phone N9 Radio P* Fuse holder for mobile phone (to joint connector box at the A pillar on the left) X* White pin plug connector X* Black 3pin plug casing only required for installation with a navigation system X3* Black 3pin socket casing for connecting the compensator X* Black 8pin socket casing X5* Black 8pin plug connector X6* Angled 3.5 mm pawl plug for connecting the microphone to the handsfree facility control module X7* 3.5 mm pawl plug for connecting the speaker to the handsfree facility control module X8* White pin socket casing X9* White 6pin socket casing not required X0* Black 0pin socket casing for mobile phone holder X* White 5pin socket casing X3 Black 6pin plug connector X86 Black 7pin socket casing X8507 Black pin socket casing X873 Earth post on the A pillar on the left ) Coding loop, white cable (only for cars with a navigation system) ) Coding loop, blue cable (only for cars with BMW Professional DSP hifi system) * These designations are only valid for this circuit diagram. Kabelfarben: Cable colours BL = Blue BR = Brown YE = Yellow GN = Green GR = Grey OR = Orange RD = Red BK = Black VI = Violet WT = White Retrofit / Installation kit No. 8 6 0 05 86, 8 6 0 06 69 Issue date: 07.000 Installation instructions No. 0 9 0 05 885 EN/0