CA 1 Tape Management CA RS 1403 Service List

CA 1 Tape Management 12.6 1 CA RS 1403 Service List Release Service Description Hiper 12.6 RO60054 S0C4 ABEND DURING CLOSE PROCESSING OF 31 BIT UNCAPTURED UCB. RO62065 TMPIUSG3 ZVAR ERROR UPDATING TMOOPT00 IN PARMLIB. RO63582 ENHANCEMENT: MULTIPLE TMC PERFORMANCE IMPROVEMENTS RO63948 TMS0MODV S0C4 WHEN PROCESSING 31 BIT UNCAPTURED UCB. RO64293 ADD COMPRESSION RATE TO CONTROL-T CVSN RO64469 DYNAM/T ERRONEOUS INFORMATION IN TMC VOLUME RECORD. RO64470 DYNSEND TMSSMF83 UPDATES REMOVE SCRATCH STATUS RO64946 TMPIUSG2 INVALID VALUE ERROR WHEN TMOOPT00 FUNC=EXT RO65021 CAG8259E OR CAT9999E/CAL0999E ISSUED WITH TQS INSTALLED. RO66083 TMSINIT5 ADD BATCH ID 70 BACK TO THE BATCH ID TABLE The CA RS 1403 service count for this release is 10

CA 1 Tape Management 2 CA RS 1403 Service List for CAG8C60 FMID Service Description Hiper CAG8C60 RO65021 CAG8259E OR CAT9999E/CAL0999E ISSUED WITH TQS INSTALLED. The CA RS 1403 service count for this FMID is 1

CA 1 Tape Management 3 CA RS 1403 Service List for CAL0C60 FMID Service Description Hiper CAL0C60 RO62065 TMPIUSG3 ZVAR ERROR UPDATING TMOOPT00 IN PARMLIB. RO63582 ENHANCEMENT: MULTIPLE TMC PERFORMANCE IMPROVEMENTS RO63948 TMS0MODV S0C4 WHEN PROCESSING 31 BIT UNCAPTURED UCB. RO64469 DYNAM/T ERRONEOUS INFORMATION IN TMC VOLUME RECORD. RO64470 DYNSEND TMSSMF83 UPDATES REMOVE SCRATCH STATUS RO64946 TMPIUSG2 INVALID VALUE ERROR WHEN TMOOPT00 FUNC=EXT RO66083 TMSINIT5 ADD BATCH ID 70 BACK TO THE BATCH ID TABLE The CA RS 1403 service count for this FMID is 7

CA 1 Tape Management 4 CA RS 1403 Service List for CBAFC60 FMID Service Description Hiper CBAFC60 RO60054 S0C4 ABEND DURING CLOSE PROCESSING OF 31 BIT UNCAPTURED UCB. RO64293 ADD COMPRESSION RATE TO CONTROL-T CVSN The CA RS 1403 service count for this FMID is 2

CA 1 Tape Management 12.6 5 CA RS 1403 - PTF RO60054 Release Service 12.6 RO60054 RO60054 M.C.S. ENTRIES = ++PTF (RO60054) S0C4 ABEND DURING CLOSE PROCESSING OF 31 BIT UNCAPTURED UCB. Users may experience a S0C4 abend during close processing of a tape dataset that was created with dynamic allocation with the S99ACUCB bit on. This signifies that the UCB is uncaptured. S0C4 abend in CTSOCE00 during close processing. Tape datasets may abend with a S0C4 during CLOSE processing. None available. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 CA TLMS Tape Management Release: 12.6 CM-$F 240 Copyright (C) 2013 CA. All rights reserved. R00001-BAF126-SP1 DESC(S0C4 ABEND DURING CLOSE PROCESSING OF 31 BIT UNCAPTURED UCB.). ++VER (Z038) FMID (CBAFC60) SUP ( RO51541 TR60054 T5XD799 ) ++HOLD (RO60054) SYSTEM FMID(CBAFC60) REASON (DYNACT ) DATE (13296) COMMENT ( PRODUCT: CA-COMMON TAPE FUNCTIONS-MVS RELEASE 12.6 SEQUENCE: AFTER APPLY PROCESSING HAS COMPLETED. Purpose: To activate the change without an IPL. Relevance: All users. Knowledge required: How to modify and submit the CAIRIM process. Access required: Ability to submit CAIRIM with modified control statements. For CA 1 clients: Steps to Perform: Modify the CAIRIM control statements as follows; PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=CTSOCE00) LOADLIB(YOUR 12.6 CTAPLINK) For CA TLMS clients: Steps to Perform: Modify the CAIRIM control statements as follows; PRODUCT(CA TLMS-PRD) VERSION(TLC6) INIT(TLC6INIT) - PARM(REINIT,LPA=CTSOCE00) LOADLIB(YOUR 12.6 CTAPLINK) ).

CA 1 Tape Management 12.6 6 CA RS 1403 - PTF RO62065 Release Service 12.6 RO62065 RO62065 M.C.S. ENTRIES = ++PTF (RO62065) TMPIUSG3 ZVAR ERROR UPDATING TMOOPT00 IN PARMLIB. When a SAVE is performed while updating hlg.ctapoptn member TMOOPTxx in the CA 1 ISPF interface, the following error is issued. Panel 'TMPIUSG3' error Number of.zvars field names does not equal number of "Z" in/out fields. ISPF Panel error during save operation. The data on the panel cannot be updated from the CA 1 ISPF interface. Use TSO edit to update options in the TMOOPTxx member. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 1 2023 Copyright (C) 2013 CA. All rights reserved. R00007-AL0126-SP1 DESC(TMPIUSG3 ZVAR ERROR UPDATING TMOOPT00 IN PARMLIB.). ++VER (Z038) FMID (CAL0C60) SUP ( TR62065 T5XD684 )

CA 1 Tape Management 12.6 7 CA RS 1403 - PTF RO63582 Release Service 12.6 RO63582 RO63582 M.C.S. ENTRIES = ++PTF (RO63582) ENHANCEMENT: MULTIPLE TMC PERFORMANCE IMPROVEMENTS PRODUCT DESCRIPTION: This PTF adds the following improvements to the TMSXTEND utility: 1) After processing the TMSAUDEX INCLUDE/EXCLUDE statements and analyzing the AUDIT activity, present a WTOR to the console showing the systems sharing the TMC and ask for a confirmation to proceed. 2) If a subtask of the TMSXTEND utility fails, do not allow the other subtask to continue processing, wasting system resources. 3) While the TMSXTEND utility is running, have a WTOR outstanding that can be replied to in order to obtain the status of the copy operation. Also, show the status in 5% increments once the copy operation has actually started. 4) Unique RNAME support. This version of TMSXTEND will manage the swap-over to using a unique RNAME for the TMC and Audit, allowing multiple TMCs to be used in the same MIM/GRS Plex For more detailed information regarding this enhancement, please refer to the informational solution RI64372. None None None PRODUCT(S) AFFECTED: CA 1-MVS Tape Management Release 12.6 1 2138 Copyright (C) 2013 CA. All rights reserved. R00018-AL0126-SP1 DESC(ENHANCEMENT: MULTIPLE TMC PERFORMANCE IMPROVEMENTS). ++VER (Z038) FMID (CAL0C60) PRE ( RO27557 RO27818 RO28581 RO28728 RO32246 RO32864 RO32878 RO34565 RO42220 RO46585 RO49589 RO51983 RO54511 RO54912 RO55480 RO57991 ) SUP ( AR55480 RO32480 RO33363 RO37805 RO38884 RO41519 RO41590 RO43218 RO45084 RO46753 RO49573 RO50553 RO53988 RO55176 RO63411 TR60732 TR60762 TR63181 TR63401 TR63411 TR63582 T101121 T101122 T246220 T5XD553 T5XD803 ) ++HOLD (RO63582) SYSTEM FMID(CAL0C60) REASON (DYNACT ) DATE (13298) COMMENT ( CA 1-MVS TAPE MANAGEMENT RELEASE 12.6 SEQUENCE AFTER APPLY PROCESSING HAS COMPLETED. PURPOSE To activate the change without an IPL. USERS All users. AFFECTED KNOWLEDGE How to modify and submit the CAIRIM process. REQUIRED ACCESS Ability to submit CAIRIM with modified control REQUIRED statements. ************************** * STEPS TO PERFORM * ************************** Modify the CAIRIM control statements as follows;

Release Service CA 1 Tape Management 12.6 8 CA RS 1403 - PTF RO63582 PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMS00SVC,SVC=xxx) LOADLIB(YOUR 12.6 CTAPLINK) PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMSKEYXB) LOADLIB(YOUR 12.6 CTAPLINK) ). ++HOLD (RO63582) SYSTEM FMID(CAL0C60) REASON (ACTION ) DATE (13298) COMMENT ( CA 1-MVS TAPE MANAGEMENT RELEASE 12.6 SEQUENCE AFTER APPLY PROCESSING HAS COMPLETED. PURPOSE To enable the new feature. USERS All users. AFFECTED KNOWLEDGE How to run CA 1 Batch Utilities. REQUIRED Access required: Ability to run CA 1 Batch Utilities. Steps to Perform: With this PTF there are two ways to implement the Unique RNAME feature of CA 1, manually or by using the TMSXTEND Utility. Procedure for Implementing with the TMSXTEND Utility: Use the following instructions implement the Unique RNAME feature of CA 1 in environments with the TMSXTEND Utility. 1. Install this PTF with SMP/E. 2. Copy the SMP/E Target load library containing this PTF to the LINKLIST library in use on all LPARs sharing the TMC. 3. Run CAS9 (CAIRIM) with the following REINIT control statements on all systems sharing the TMC (unless the systems themselves are shutdown and will be RE-IPL'ed anyway) //PARMLIB DD * PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMS00SVC,SVC=XXX) - LOADLIB(YOUR 12.6 CTAPLINK) PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMSKEYXB) - LOADLIB(YOUR 12.6 CTAPLINK) 4. Run the TMSXTEND Utility with a new control statement of "UNIQUE_RNAME=YES". For information on how to use the the TMSXTEND Utility please refer to the CA 1 Utilities and Reports Reference Guide. Back out instructions for the TMSXTEND Utility: There are 2 things that can be "backed out"; the feature itself and the maintenance. If the feature has been enabled it must be

Release Service CA 1 Tape Management 12.6 9 CA RS 1403 - PTF RO63582 disabled PRIOR to a "back out" of the maintenance. To disable the new feature, repeat steps 4 (in the above steps), however change the control statement to "UNIQUE_RNAME=NO". Once the new feature has been disabled, the maintenance can be backed out as well. If the maintenance is backed out while the feature is still enabled, a S130 or S138 abend may occur when running TMSINIT. ********************************************************************* Procedure for Manually Implementing Use of Unique RNAME: Use the following instructions to manually implement the Unique RNAME feature of CA 1 in environments where tape activity can be stopped on all except one (1) system 1. Install this PTF with SMP/E. 2. Copy the SMP/E Target load library containing this PTF to the LINKLIST library in use on all LPARs sharing the TMC. 3. Run CAS9 (CAIRIM) with the following REINIT control statements on all systems sharing the TMC (unless the systems themselves are shutdown and will be RE-IPL'ed anyway) //PARMLIB DD * PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMS00SVC,SVC=XXX) - LOADLIB(YOUR 12.6 CTAPLINK) PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMSKEYXB) - LOADLIB(YOUR 12.6 CTAPLINK) 4. When you are ready to implement the Unique RNAME feature, determine if all but 1 system can have CA 1 completely in-activated (no tape activity allowed of any kind). Until that point, go no further. Once CA 1 has been completely in-activated on all except 1 system, then continue to the next step. (This means running TMSINIT and replying with your shutdown password instead of simply "U".) 5. On the one system still doing active tape processing, you will need to use the TMSUDSNB utility to update Control Record 1 (CTL#1) FLAG1 to indicate that Unique RNAME processing is to be used for this TMC. Use the following JCL to achieve this: //STEP1 EXEC PGM=TMSUDSNB //STEPLIB DD DSN=your.cai.CTAPLINK,DISP=SHR //TMSRPT DD SYSOUT=* //TMC DD DSN=your.tmc,DISP=SHR //SYSIN DD * PASSWORD=your shutdown value CTL1 VER RECID=TMSCTL#1 REP FLAG1=40 /*

Release Service CA 1 Tape Management 12.6 10 CA RS 1403 - PTF RO63582 NOTE: You should expect an RC=4 from TMSUDSNB any time you change the CTL#1 FLAG1 bit setting. 6. After running TMSUDSNB and setting FLAG1 bit x'40'on (or off to disable) you may optionally also run TMSBINQ with a HEADERS control statement to display the bit settings for FLAG1. 7. Run TMSINIT to re-init CA 1. When TMSINIT runs after CAS9 during startup, you should see the following message IEFTMS76 UNIQUE RNAME SUPPORT ACTIVE This indicates the TMSINIT has detected the FLAG1 bit is set on requesting Unique RNAME processing. The Unique RNAME that includes the TMC/Audit volsers and DSNs will be used for all RESERVE/ENQ activity on the TMC and Audit. Examples of the RNAMEs displayed when a GRS command is issued follow: D GRS,RES=(TMSQNAME,*) ISG343I 05.58.11 GRS STATUS 480 S=SYSTEMS TMSQNAME TMS-TMC-volxxx-your.tmc.name 8. If you had simply de-activated CA 1 on the other systems, you can re-activate CA 1 by simply running TMSINIT and replying "U" (the CAIRIM - step 3 must have been done however). If the systems had been shutdown completely, they will pick everything up after an IPL. The IEFTMS76 should appear after every TMSINIT going forward from this point. Back out instructions for manual implementation: There are 2 things that can be "backed out"; the feature itself and the maintenance. If the feature has been enabled (steps 5-8) it must be disabled PRIOR to a "back out" of the maintenance. To disable the new feature, repeat steps 4-8 however in step 5 change " REP FLAG1=40" to "REP FLAG1=00". Once the new feature has been disabled, the maintenance can be backed out as well. If the maintenance is backed out while the feature is still enabled, a S130 or S138 abend may occur when running TMSINIT. Knowledge required: ). ++HOLD (RO63582) SYSTEM FMID(CAL0C60) REASON (DOC ) DATE (13298) COMMENT ( CA 1-MVS Tape Management Release 12.6 *************************** * PUBLICATION * *************************** PLEASE REFER TO PDC RI64372 FOR MORE INFORMATION ON this new enhancement. Also, a fifth edition of the CA 1 documentation is available on the CA support web site that contains updated information on this enhancement. ).

CA 1 Tape Management 12.6 11 CA RS 1403 - PTF RO63948 Release Service 12.6 RO63948 RO63948 M.C.S. ENTRIES = ++PTF (RO63948) TMS0MODV S0C4 WHEN PROCESSING 31 BIT UNCAPTURED UCB. Users may experience a S0C4 abend during Label or Density change of a dataset that was created with dynamic allocation with the S99ACUCB bit on. This bit signifies that the allocate function can use the actual UCB address instead of a captured copy. S0C4 abend in TMS0MODV during Label or Density change. Tape datasets may abend with a S0C4 during Label or Density change. None available. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 1 2158 COPYCAT CTC7302A VOLUME CURRENTLY IN USE WHEN AIVS MULTIFILE Message CTC7302A issued when copying secondary files that reside on an AIVS (Alternate Internal Volume Serial) volume. When using COPYCAT's Filecopy to copy secondary files that reside on an AIVS volume, message CTC7203A is issued preventing the copy from completing. CTC7302A Volume currently in use - vvvvvv CTC7303R Reply 'retry', 'wait', 'abend', or 'bypass' Job has to be cancelled preventing AIVS secondary files from being copied. None available. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 1 2080 TMSOCEPR IEC710I RESOLVE MULTI-VOLUME CONFLICT When reading a multi-volume dataset as input and specifying only the first volume in the JCL, IBM message IEC710I ANOTHER VOLUME EXPECTED is issued at the end of the first volume when an End-Of-Volume (EOV) is read instead of an End-Of-File (EOF). CA 1 now resolves this conflict by filling in the next volume to be mounted via the Label Anomaly Exit until the end of the volume chain within the TMC is reached. When the exit is invoked, the IBM message IEC716I TAPE MULTIVOLUME LIST CORRECTED will be issued and the job will continue reading until the next EOV condition arises. This will then be repeated until an EOF condition is reached or the application stops reading the file. Only the first volume of a multi-volume dataset is read for input and the job abends. Not all volumes are read when multiple volumes expected. Code all volumes associated with the dataset in the VOL= JCL statement or allow the MVS/Catalog to supply the complete list of volsers. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 1 2139 Copyright (C) 2013 CA. All rights reserved. R00021-AL0126-SP1 DESC(TMS0MODV S0C4 WHEN PROCESSING 31 BIT UNCAPTURED UCB.). ++VER (Z038) FMID (CAL0C60) PRE ( RO37280 ) SUP ( TR63948 T5XD762 T5XD792 )

Release Service CA 1 Tape Management 12.6 12 CA RS 1403 - PTF RO63948 ++HOLD (RO63948) SYSTEM FMID(CAL0C60) REASON (DYNACT ) DATE (13298) COMMENT ( PRODUCT: CA 1-MVS TAPE MANAGEMENT RELEASE 12.6 SEQUENCE: AFTER APPLY PROCESSING HAS COMPLETED. Purpose: To activate the change without an IPL. Relevance: All users. Knowledge required: How to modify and submit the CAIRIM process. Access required: Ability to submit CAIRIM with modified control statements. Steps to Perform: Modify the CAIRIM control statements as follows; PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMS0MODV) LOADLIB(YOUR 12.6 CTAPLINK) PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMSOCEPR) LOADLIB(YOUR 12.6 CTAPLINK) ).

CA 1 Tape Management 12.6 13 CA RS 1403 - PTF RO64293 Release Service 12.6 RO64293 RO64293 M.C.S. ENTRIES = ++PTF (RO64293) ADD COMPRESSION RATE TO CONTROL-T CVSN Compression rate is not converted to CA 1 or TLMS when converting from Control-T. The VOLPERC and FILEPERC fields have values of zeros after the conversion. Low, these fields are strictly used for reporting purposes. None. PRODUCT(S) AFFECTED: CA TLMS Release 12.6 CA 1 Release 12.6 CM-$F 242 BLKSIZE, OUTCODE AND OUTDATE NOT CONVERTED FROM CONTROL-T The Control-T conversion job CTSJCTL5 is not converting BLKSIZE, OUTCODE and OUTDATE. After converting to CA 1 or TLMS, these fields still contain their default values. BLKSIZE, OUTCODE and OUTDATE remain as hexzeros. These values must be updated manually. OUTCODE and OUTDATE may be updated through the CA 1 or TLMS vaulting system if rules are in place for these volumes. PRODUCT(S) AFFECTED: CA TLMS Release 12.6 CA 1 Release 12.6 CM-$F 197 SMS CLASS IS NOT CONVERTED FROM CONTROL-T When converting from Control-T to CA 1 or TLMS, the SMS management class is not converted. The SMS management class is left at the default value of spaces. Low. This should only affect reporting unless the SR option is set to YES in CA 1, in which case the retention of the volume may not be as expected. None. PRODUCT(S) AFFECTED: CA TLMS Release 12.6 CA 1 Release 12.6 CM-$F 222 CONTROL-T TYPE "V" RETENTION IS CONVERTED TO CATALOG During a Control-T conversion, the EXPDT field is updated to be CATALOG control when the input Control-T record specifies the retention to be a type "V". This indicates a VAULT type retention and the CA 1 or TLMS EXPDT should reflect the vault retention date. The EXPDT is updated to be CATALOG controlled. It is possible that the dataset is not CATALOG'ed to the system running CA 1 or TLMS and could be scratched prematurely. A manual update to the EXPDT is required without having this PTF applied. PRODUCT(S) AFFECTED: CA-COMMON TAPE FUNCTIONS-MVS Release 12.6 CM-$F 226 CHECK "SCRATCH PENDING" WITH CONTROL-T CNVSN If Control-T has HSM volumes that are EDM controlled and HSM releases

Release Service CA 1 Tape Management 12.6 14 CA RS 1403 - PTF RO64293 them, Control-T may not yet have put them in scratch status. Program CTSCCON6 converts these records as live volumes while Control-T has them in a 'SCRATCH PENDING" status. Volumes that should be scratch are converted to live volumes in CA 1 and TLMS. These volumes will never go scratch in CA 1 or TLMS without a manual update. For CA 1 users, manually update the EDMID to spaces and update FLAG3 to x'00' and update the EXPDT to the current date. For TLMS users, manually scratch the volumes. PRODUCT(S) AFFECTED: CA TLMS Release 12.6 CA 1 Release 12.6 CM-$F 243 Copyright (C) 2013 CA. All rights reserved. R00004-BAF126-SP1 DESC(ADD COMPRESSION RATE TO CONTROL-T CVSN). ++VER (Z038) FMID (CBAFC60) SUP ( TR64293 T246229 )

CA 1 Tape Management 12.6 15 CA RS 1403 - PTF RO64469 Release Service 12.6 RO64469 RO64469 M.C.S. ENTRIES = ++PTF (RO64469) DYNAM/T ERRONEOUS INFORMATION IN TMC VOLUME RECORD. When CA Dynam/T takes ownership of a volume, but does not assign a controlling data set to it, CA 1 does not update the Data Set Name, EXPDT or Creation Date fields. Data Set Name, EXPDT and Creation fields are left with whatever residual data had been in those fields originally. Since the volume will not be scratched until Dynam/T releases it, and this is only when secondary files cause a span to secondary volumes on the CA-Dynam/T system, this has little impact other than reporting. Use TMSUPDTE to clear fields. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 1 2022 Copyright (C) 2013 CA. All rights reserved. R00026-AL0126-SP1 DESC(DYNAM/T ERRONEOUS INFORMATION IN TMC VOLUME RECORD.). ++VER (Z038) FMID (CAL0C60) SUP ( TR64469 ) ++HOLD (RO64469) SYSTEM FMID(CAL0C60) REASON (DYNACT ) DATE (13305) COMMENT ( +----------------------------------------------------------------------+ CA 1-MVS Tape Management Release 12.6 SEQUENCE After Apply PURPOSE To activate this change. USERS All users. AFFECTED KNOWLEDGE How to Refresh LLA and Recycle the Dyncomm STC. REQUIRED ACCESS Ability to issue LLA refresh commands and Start/Stop REQUIRED Dyncomm. ************************** * STEPS TO PERFORM * ************************** 1. F LLA,REFRESH 2. P DYNCOMM 3. S DYNCOMM ).

CA 1 Tape Management 12.6 16 CA RS 1403 - PTF RO64470 Release Service 12.6 RO64470 RO64470 M.C.S. ENTRIES = ++PTF (RO64470) DYNSEND TMSSMF83 UPDATES REMOVE SCRATCH STATUS DYNCOMM interface is sending two updates for a tape that is being scratched. The first update places the volume in scratch status. The second update is from TMSSMF83 to update the number of times a tape is cataloged. This update removes the tape from scratch status. Volumes that are scratched are immediately taken out of scratch status. Depending on the size of a client's scratch pool, the amount of available scratch tapes may be reduced to an unfavorable number. None. PRODUCT(S) AFFECTED: CA 1-MVS Tape Management Release 12.6 1 2089 Copyright (C) 2013 CA. All rights reserved. R00027-AL0126-SP1 DESC(DYNSEND TMSSMF83 UPDATES REMOVE SCRATCH STATUS). ++VER (Z038) FMID (CAL0C60) SUP ( TR64470 T5XD767 ) ++HOLD (RO64470) SYSTEM FMID(CAL0C60) REASON (DYNACT ) DATE (13304) COMMENT ( +----------------------------------------------------------------------+ CA 1-MVS Tape Management Release 12.6 SEQUENCE After Apply PURPOSE To activate this change. USERS Users that have the CA Dynam/T interface to CA 1 active. AFFECTED KNOWLEDGE How to Refresh LLA and Recycle the Dyncomm STC. REQUIRED ACCESS Ability to issue LLA refresh commands and Start/Stop REQUIRED Dyncomm. ************************** * STEPS TO PERFORM * ************************** 1. F LLA,REFRESH 2. P DYNCOMM 3. S DYNCOMM ).

CA 1 Tape Management 12.6 17 CA RS 1403 - PTF RO64946 Release Service 12.6 RO64946 RO64946 M.C.S. ENTRIES = ++PTF (RO64946) TMPIUSG2 INVALID VALUE ERROR WHEN TMOOPT00 FUNC=EXT If CA 1 option FUNC is set to EXT in TMOOPTxx, a panel error will occur in the CA 1 ISPF Systems Options Maintenance panels. In the CA 1 ISPF Systems Options Maintenance panels, if UPDATE is entered the second panel will produce an INVALID VALUE error when the CA 1 option FUNC is set to EXT in TMOOPT00 member. This error occurs when paging from Panel 2 to Panel 3. Unable to page from Panel 2 to Panel 3. Use TSO edit to update options in member TMOOPTxx. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 1 2033 Copyright (C) 2013 CA. All rights reserved. R00036-AL0126-SP1 DESC(TMPIUSG2 INVALID VALUE ERROR WHEN TMOOPT00 FUNC=EXT). ++VER (Z038) FMID (CAL0C60) SUP ( TR62074 TR64946 T5XD697 )

CA 1 Tape Management 12.6 18 CA RS 1403 - PTF RO65021 Release Service 12.6 RO65021 RO65021 M.C.S. ENTRIES = ++PTF (RO65021) CAG8259E OR CAT9999E/CAL0999E ISSUED WITH TQS INSTALLED. If TQS software initializes after CA 1 or CA TLMS initialized, the following CAL0999E/CAT9999E messages may be issued during tape processing. For CA 1 clients: CAL0999E CA 1 HAS DETECTED THAT ONE OR MORE TAPE INTERCEPTS ARE NOT ACTIVE!! TAPES MAY NOT BE PROTECTED AND TAPE ACTIVITY MAY NOT BE RECORDED. For CA TLMS clients: CAT9999E CA 1 HAS DETECTED THAT ONE OR MORE TAPE INTERCEPTS ARE NOT ACTIVE!! TAPES MAY NOT BE PROTECTED AND TAPE ACTIVITY MAY NOT BE RECORDED. Many CAL0999E or CAT9999E messages may be produced during Open Output processing of Tape datasets. Although an error message is produced, CA 1 or CA TLMS tracking is not lost. For CA 1 clients: Ensure that TQS software initializes before CA 1. Or using CAIRIM, specify the following PARM for the L0C6INIT program for CA 1: PARM(REINIT,OSI=REINIT) and start the CAS9 procedure again. For CA TLMS clients: Ensure that TQS software initializes before CA TLMS. Or using CAIRIM, specify the following PARM for the TLC6INIT program for CA TLMS: PARM(REINIT,OSI=REINIT) and start the CAS9 procedure again. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 CA TLMS Tape Management Release: 12.6 CM-G8 23 G8UTY S0C4 IF O/C/EOV MODULES RELINKED WITH USERNAME PREFIX. If an Open/Close/Eov routine is relinked with a new name and the original primary name of the routine is defined as an alias, G8UTY will abend with a S0C4. Abend S0C4 during apply of TMSOCE1A. CA 1 O/C/EOV intercepts will not be installed and CA 1 will not be activated successfully. Use MLPA with the modified Open/Close/Eov routines link edited with the original names. PRODUCT(S) AFFECTED: CA 1 Tape Management System Release: 12.6 CA TLMS Tape Management Release: 12.6 CM-G8 24 Copyright (C) 2013 CA. All rights reserved. R00002-AG8126-SP1 DESC(CAG8259E OR CAT9999E/CAL0999E ISSUED WITH TQS INSTALLED.). ++VER (Z038) FMID (CAG8C60) SUP ( RO41064 TR60404 TR65021 T5XD788 ) ++HOLD (RO65021) SYSTEM FMID(CAG8C60) REASON (DYNACT ) DATE (13317) COMMENT ( +----------------------------------------------------------------------+ CA-OSI/COMMON COMPONENT-MVS Release 12.6

Release Service CA 1 Tape Management 12.6 19 CA RS 1403 - PTF RO65021 SEQUENCE After Apply PURPOSE To activate the change without an IPL. USERS All users. AFFECTED KNOWLEDGE How to modify and submit the CAIRIM process. REQUIRED ACCESS Ability to submit CAIRIM with modified control REQUIRED statements. ************************** * STEPS TO PERFORM * ************************** For CA 1 clients: PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,OSI=REINIT) LOADLIB(YOUR 12.6 CTAPLINK) For CA TLMS clients: Modify the CAIRIM control statements as follows; PRODUCT(CA-TLMS/MVS) VERSION(TLC6) INIT(TLC6INIT) - PARM(REINIT,OSI=REINIT) LOADLIB(YOUR 12.6 CTAPLINK) ).

CA 1 Tape Management 12.6 20 CA RS 1403 - PTF RO66083 Release Service 12.6 RO66083 RO66083 M.C.S. ENTRIES = ++PTF (RO66083) TMSINIT5 ADD BATCH ID 70 BACK TO THE BATCH ID TABLE TMS0131E INI5 Too many BATCH_IDs entered issued during TMSINIT if attempting to use BatchID 70. This was allowed in prior releases of CA 1. Abend U0006 in TMSINIT if Batchid of 70 is used. This was removed in r12.6 as the user Batch_ID's in TMOKEY00 are 60-69. However, prior releases of CA 1 allowed this. Abend in TMSINIT and unable to use Batch_ID of 70. None. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 1 2157 TMSINIT U0006 ABEND IF XCOR AND YCOR OMITTED IN TMOKEY00. Problem Description: Abend U0006 in TMSINIT if XCOR and YCOR not found in the KWORD section of member TMOKEY00 in the hlq.ctapoptn dataset. If the XCOR and YCOR values are omited in TMOKEY00 because they should take the default values of zero, a U0006 Abend occurs with TMS0127E INI5 Required keyword option missing. Unexpected abend in TMSINIT. Add XCOR=00 and YCOR=00 to the KWORD section of TMOKEY00 and start TMSINIT again. PRODUCT(S) AFFECTED: CA 1-MVS Tape Management Release 12.6 1 2154 Copyright (C) 2013 CA. All rights reserved. R00046-AL0126-SP1 DESC(TMSINIT5 ADD BATCH ID 70 BACK TO THE BATCH ID TABLE). ++VER (Z038) FMID (CAL0C60) PRE ( RO27557 RO27818 RO28581 RO32246 RO32878 RO42202 RO42220 ) SUP ( RO33736 RO50778 RO53782 TR63352 TR63825 TR65954 TR66083 ) ++HOLD (RO66083) SYSTEM FMID(CAL0C60) REASON (DYNACT ) DATE (13352) COMMENT ( +----------------------------------------------------------------------+ CA 1-MVS Tape Management Release 12.6 SEQUENCE After Apply PURPOSE To activate the change without an IPL. USERS All users. AFFECTED KNOWLEDGE How to modify and submit the CAIRIM process. REQUIRED ACCESS Ability to submit CAIRIM with the modified control REQUIRED statements. ************************** * STEPS TO PERFORM * **************************

Release Service CA 1 Tape Management 12.6 21 CA RS 1403 - PTF RO66083 Modify the CAIRIM control statements as follows; PRODUCT(CA-1/MVS) VERSION(L0C6) INIT(L0C6INIT) - PARM(REINIT,LPA=TMSKEYXB) LOADLIB(YOUR 12.6 CTAPLINK) Modify hlq.ctapoptn member TMOKEY00 with your program name for the Batch_ID_70=Your_Program_Name Then start TMSINIT to activate this entry. ).