connection SubSat-sp Set (same possibilities with 19" HDSP-3, HDSP-6 amplifier) ampchannel OUT 3 (800W/4 ohm) Speakon connection top 1+/1- ampchannel OUT 2 (800W/4 ohm) Speakon connection top 1+/1 In all Voice-Acoustic self-powered subwoofers: 3-channel class-d 4000W amplifier inside. 1x 2400W/4 ohm 2x 800W/4 ohm DSP-board with 2x Inputs and 3x internal puts 2x XLR loop through OUT 2 (800W/4 ohm), Speakon 1+/1OUT 1 (2400W/4 ohm), Speakon 2+/2- OUT 3 (800W/4 ohm), Speakon 1+/1OUT 1 (2400W/4 ohm), Speakon 2+/2-1, 2400W, both Speakons 2+/2 2, 800W, 1+/1 2, 800W, 1+/1- Subwoofer on 1 get a mono sum with und Top on 2 get stereo left In 1 Top on 3 get stereo right In 2
connection SubSat-sp Set with slave-sub Ampchannel OUT 2 (800W) Speakon top 1+/1- Ampchannel OUT 3 (800W) Speakon top 1+/1- OUT 2 (800W/4 ohm), Speakon 1+/1OUT 1 (2400W/4 ohm), Speakon 2+/2- Ampchannel OUT 1 (2400W) Speakon connection Sub 2+/24-pole cable necessary OUT 3 (800W/4 ohm), Speakon 1+/1OUT 1 (2400W/4 ohm), Speakon 2+/2-1, 2400W, both Speakons 2+/2 2, 800W, 1+/1 2, 800W, 1+/1- Subwoofer on 1 get a mono sum with und Top on 2 get stereo left In 1 Top on 3 get stereo right In 2
connection & approach delayline stereo with SubSat-sp set Delay Delay XLR Patchkabel On each subwoofer can be connect a second slave sub. XLR Patchkabel The long delay-times with up to 275m are always in the Input channels. The delay-times in the put channels are only short delays with maximal 2,7m for time-alignment for bi-amping systems delay-line in 1 must be mute Subwoofer on 1 must get only the signal from. The channel must be muted signal with delay Top on 2 get In 1 in you can adjust the delaytime Top on 3 get In 2, delay-line
connection & approach delayline mono with SubSat-sp set mono delay-line mono. If possible switch the mixing desk on mono You can connect with a 4-pole cable a second slave sub. OUT 2 (800W/4 Ohm), Speakon 1+/1OUT 1 (2400W/4 Ohm), Speakon 2+/2- delay-line on OUT 3 (800W/4 Ohm), Speakon 1+/1OUT 1 (2400W/4 Ohm), Speakon 2+/2The long delay-times with up to 275m are always in the Input channels. The delay-times in the put channels are only short delays with maximal 2,7m for time-alignment for bi-amping systems Delayline in 1 must be mute Subwoofer on 1 must get only the signal from. The channel must be muted signal with delay Top on 2 get In 1 in you can adjust the delaytime Top on 3 get In 2, delay-line
connection & approach stereo monitoring with SubSat-sp set Mix On each subwoofer can be connect a second slave sub. in 1 must be mute Subwoofer on 1 must get only the signal from. The channel must be muted monitor mix Top on 2 get In 1 on 3 get In 2
connection & approach stereo monitoring with SubSat-sp set mono monitoring mono Mix. If possible switch the mixing desk on mono You can connect with a 4-pole cable a second slave sub. OUT 2 (800W/4 Ohm), Speakon 1+/1OUT 1 (2400W/4 Ohm), Speakon 2+/2- Mix auf OUT 3 (800W/4 Ohm), Speakon 1+/1OUT 1 (2400W/4 Ohm), Speakon 2+/2- in 1 must be mute Subwoofer on 1 must get only the signal from. The channel must be muted Mix Top on 2 get In 1 on 3 get In 2