Active resistance thermometer measuring transducer Data sheet 099_en_06 PHOENIX CONTACT 0-0- Description The 6. mm wide MINI MCR-SL-PT00-UI-... is a configurable, -way isolated temperature measuring transducer. It is suitable for connecting Pt 00-resistance thermometers according to IEC 6075 in, and -conductor connection method. The electrically isolated analog standard signals 0...0 ma,...0 ma, 0...0 V, 0...5 V,...5 V, 0...0 V, 0...0 ma or 0... ma are available on the output side. The DIP switches are accessible on the side of the housing and allow the following parameters to be configured: Connection method Temperature range to be measured Output signals as well as Type of fault evaluation the voltage (9. V DC to 0 V DC) can be supplied either via the connection terminal blocks of the module or in conjunction with the DIN rail connector. Features Configurable -way temperature transducer -, -, -conductor connection method for Pt 00 resistance thermometer Measuring range 0 C to 850 C Output signal range 0...0 ma,...0 ma, 0...0 V, 0...5 V,...5 V,0...0 V, 0...0 ma or 0... ma Approval for Ex-zone (na) Screw or spring-cage connection can be provided Can be supplied configured or unconfigured WARNING: Correct usage in potentially explosive areas The module is a category item of electrical equipment. It is absolutely vital to follow the instructions provided here during installation and observe the information in the "Safety regulations and installation notes". Make sure you always use the latest documentation. It can be downloaded from the product at www.phoenixcontact.net/catalog. This data sheet is valid for all products listed on the following page:
Table of contents Description... Table of contents... Ordering data.... Order key... Technical data... 5 5 Safety regulations and installation notes... 7 5. Installation notes... 7 5. Installation in the Ex area (zone )... 7 6 Installation... 8 6. Connection notes... 8 6. Structure... 8 6. Block diagram... 8 6. Power supply... 8 6.5 Assembly... 9 6.6 Connecting the wires... 9 7 Configuration... 0 7. Configuration table... 8 Diagnostics LED... 9 Connection/application example... 099_en_06 PHOENIX CONTACT
Ordering data Description Type Order No. Pcs. / Pkt. MCR temperature transducer for Pt 00 temperature sensors, configured via DIP switch, with screw connection, pre-configured (pay attention to the order key) MCR temperature transducer for Pt 00 temperature sensors, configured via DIP switch, with spring-cage connection, pre-configured MCR temperature transducer for Pt 00 temperature sensors, configured via DIP switch, with screw connection, not pre-configured MCR temperature transducer for Pt 00 temperature sensors, configured via DIP switch, with spring-cage connection, not pre-configured MINI MCR-SL-PT00-UI 865 MINI MCR-SL-PT00-UI-SP 8676 MINI MCR-SL-PT00-UI-NC 867 MINI MCR-SL-PT00-UI-SP-NC 8686 Accessories Type Order No. Pcs. / Pkt. DIN rail connector (TBUS), 5-pos., for bridging the supply voltage, can be snapped onto NS 5/... DIN rails according to EN 6075 MCR power terminal block for supplying several MINI Analog modules via the DIN rail connectors, with screw connection, current consumption up to max. A MCR power terminal block for supplying several MINI-ANALOG modules via the DIN rail connectors, with spring-cage connection, current consumption up to max. A DIN rail power supply unit, primary-switched mode, slim design, output: V DC /.5 A DIN rail power supply unit, primary-switched mode, slim design, output: V DC /.5 A, ATEX approval Eight MINI analog signal converters with screw connection method can be connected to a control system using a system adapter and system cabling with a minimum of wiring and very low error risk. Fold up transparent cover for MINI MCR modules with additional labeling option using insert strips and flat Zack marker strip 6. mm Label for extended marking of MINI MCR modules in connection with the MINI MCR-DKL MINI analog multiplexer, generates one analog output from 8 analog input signals, for MINI analog module with screw connection. ME 6, TBUS-,5/5-ST-,8 GN 86978 0 MINI MCR-SL-PTB 86 MINI MCR-SL-PTB-SP 867 MINI-SYS-PS-00-0AC/DC/.5 86698 MINI-PS-00-0AC/DC/.5/EX 86665 MINI MCR-SL-V8-FLK 6-A 868 MINI MCR DKL 08 0 MINI MCR-DKL-LABEL 807 0 MINI MCR-SL-MUX-V8-FLK 6 885 099_en_06 PHOENIX CONTACT
. Order key (standard configuration entered as example) Order No. Connection Measuring range [ C] Output Failure- Factory calibration certificate Start End information ) method 865 / / 0 / 00 / OUT0 / A / NONE = -wire 0 Range OUT0 = 0...0 ma A NONE = Without factory 865 = = -wire -0 OUT0 =...0 ma B YES = With factory calibration...-pt00-ui = -wire -0 (increment) OUT0 = 0...0 V C certificate (fee) -0 0...00 (5 K) OUT05 = 0...5 V D 8676 = -0 0...00 (0 K) OUT06 =...5 V YESPLUS = Factory calibration...-pt00-ui-sp -50 0...700 (0 K) OUT07 = 0...0 ma -00 750...850 (50 K) OUT08 = 0... ma -50 OUT09 = 0...0 V certificate with 5 measuring points (fee) ) Failure information (depends on the output signal range): Measured overrange Open circuit 0...0 ma...0 ma 0...0 V 0...0 ma...0 ma 0...0 V A 0,5 ma 0,5 ma 0,5 V ma ma 0,5 V B 0,5 ma 0,5 ma 0,5 V ma ma 0,5 V C 0 ma 0 ma 0 V ma ma 0,5 V D 0 ma 0 ma 0 V 0 ma ma 0 V Measured underrange Short circuit 0...0 ma...0 ma 0...0 V 0...0 ma...0 ma 0...0 V A 0 ma ma 0 V 0 ma ma 0 V B 0 ma,5 ma 0 V 0 ma ma 0 V C 0 ma ma 0 V ma ma 0,5 V D 0 ma ma 0 V 0 ma ma 0 V 099_en_06 PHOENIX CONTACT
Technical data Input Configurable/programmable Yes Sensor type Pt 00 (IEC 6075/EN 6075) Sensor input current ma (constant) Max. permissible overall conductor resistance 0 Ω (Per cable) Measuring range span min. 50 K Connection method,, -wire Output Voltage output signal Max. voltage output signal Non-load voltage Current output signal Max. current output signal Configurable/programmable Short-circuit current Load/output load voltage output Ripple Load/output load current output Supply Nominal supply voltage Supply voltage range Max. current consumption Power consumption 0 V... 0 V 0 V... 0 V 0 V... 5 V V... 5 V Approx..5 V Approx..5 V ma... 0 ma 0 ma... 0 ma 0 ma... ma 0 ma... 0 ma (please indicate if different setting when ordering) ma Yes, preconfigured Approx. 0 ma 0 kω < 0 mv PP (at 0 kω) < 500 Ω (at 0 ma) V DC 9. V DC... 0 V DC (to bridge the supply voltage, the DIN rail connector (ME 6, TBUS-,5/5-ST-,8 GN, Order No. 86978) can be used. It can be snapped onto a 5 mm DIN rail according to EN 6075) < ma (at V DC) < 500 mw General data Transmission error in the set measuring range ((00 K / set measurement range [K]) + 0.)% Transmission error in the full measuring range 0, % Maximum temperature coefficient < 0.0 %/K Step response (0 99%) < 60 ms Electrical isolation Basic insulation according to EN 600 Surge voltage category II Mounting position Any Degree of protection IP0 Pollution degree Rated insulation voltage 50 V AC/DC Test voltage, input/output/supply.5 kv (50 Hz, min.) Dimensions W / H / D 6. mm / 9. mm / 0.5 mm Type of housing PBT green 099_en_06 PHOENIX CONTACT 5
Connection data Screw connection Spring-cage conn. Conductor cross section, solid 0. mm²....5 mm² 0. mm²....5 mm² Conductor cross section, stranded 0. mm²....5 mm² 0. mm²....5 mm² Stripping length mm 8 mm Ambient conditions Ambient temperature (operation) -0 C... 65 C Ambient temperature (storage/transport) -0 C... 85 C Conformance with EMC Directive 00/08/EC Noise immunity according to EN 6000-6- Noise emission according to EN 6000-6- Conformance / approvals Conformance ATEX UL, USA / Canada UL, USA / Canada Shipbuilding CE-compliant II G Ex na IIC T Gc X UL 508 Recognized Class I, Div., Groups A, B, C, D T5 GL EMC D 099_en_06 PHOENIX CONTACT 6
5 Safety regulations and installation notes 5. Installation notes The category device is suitable for installation in the zone potentially explosive area. It fulfills the requirements of EN 60079-0:009 and EN 60079-5:00. Installation, operation, and maintenance may only be carried out by qualified electricians. Follow the installation instructions described. When installing and operating the device, the applicable regulations and safety directives (including national safety directives), as well as general technical regulations, must be observed. The technical data is provided in this package slip and on the certificates (conformity assessment, additional approvals where applicable). It is not permissible to open or modify the device. Do not repair the device yourself but replace it with an equivalent device. Repairs may only be carried out by the manufacturer. The manufacturer is not liable for damage resulting from violation. The IP0 degree of protection (IEC 6059/EN 6059) of the device is intended for use in a clean and dry environment. Do not subject the device to any load that exceeds the described limits. The device is not designed for use in atmospheres with a danger of dust explosions. 5. Installation in the Ex area (zone ) Observe the specified conditions for use in potentially explosive areas. The device must be installed in a housing (control or distributor box) which meets the requirements of EN 60079-5 and provides at least IP5 (EN 6059) degree of protection. During installation and when connecting the supply and signal circuits, observe the requirements of EN 60079-. Devices may only be connected to circuits in zone if they are suitable for operation in Ex zone and for the prevailing conditions at the place of use. In potentially explosive areas, terminals may only be snapped onto or off the DIN rail connector and wires may only be connected or disconnected when the power is switched off. The device must be stopped and immediately removed from the Ex area if it is damaged, has been subjected to an impermissible load, has been stored incorrectly, or if it malfunctions. You can download the latest documents for these devices from www.phoenixcontact.net/catalog. 099_en_06 PHOENIX CONTACT 7
6 Installation 6. Connection notes 6. Block diagram Sensor / Field IN OUT PLC / DCS NOTE: Electrostatic discharge! The device contains components that can be damaged or destroyed by electrostatic discharge. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD) according to EN 60-5- and EN 60-5-. ϑ PT 00 ϑ ϑ OUT U,I 5 + active GND 6 +V 7 + GND 8 5 6 passive 6. Structure 6 5 Figure www.phoenixcontact.com Serial No. Structure MINI MCR SL PT00 UI 85 Blomberg, Germany IN: -50...850 C / -8...56 F 9,...0VDC Ord. No.: 8 6 5 Pt00 Transducer OUT: 0()...0mA, 0()...5V, 0...0V, 0...()0mA, 0...0V T 0...+65 C /...+9 F PLC / DCS Sensor / Field. Input: Pt 00 resistance thermometer. Cover. Diagnostics LED. Groove for ZBF 6 zack marker strip 5. Output: Standard signals 6. Supply voltage 7. Connection option for DIN rail connector 8. Universal snap-on foot for EN DIN rails 9. DIP switch S 0. DIP switch S. DIP switch S amb ON S OFF passive active GND +V GND ON OFF OUT U,I 5 + 5 6-6 + 7-8 - +V GND S 8 S 8 ϑ ϑ ϑ 7 II G Warning Do n ot seperate when energized Ex na II C T Gc X PROCESS CONTROL EQUIPMENT FOR HAZARDOUS LOCATIONS ZN C l. I, Div., Grps. A,B,C,D T5 5mA max Use Class pwr src 0 8 9 Figure Block diagram 6. Power supply +V GND Zone Div. NOTE: Never connect the supply voltage directly to the DIN rail connector. It is not permitted to draw power from the DIN rail connector or from individual modules. Supply via the MINI Analog Module Where the total current consumption of the aligned modules does not exceed 00 ma, the power can be supplied directly at the connection terminal blocks of the module. A 00 ma fuse should be connected upstream. Supply via a power terminal block The MINI MCR-SL-PTB power terminal block (Order No. 86) or the MINI MCR-SL-PTB-SP power terminal block (Order No. 867), which are the same shape, are used to feed the supply voltage to the DIN rail connector. A A fuse should be connected upstream. Supply via a system power supply unit The system power supply unit with.5 A output current connects the DIN rail connector to the supply voltage and can thus be used to supply several modules from the mains. MINI-SYS-PS-00-0AC/DC/.5 (Order No. 86698) Potentially explosive areas: MINI-PS-00-0AC/DC/.5/EX (Order No. 86665) 099_en_06 PHOENIX CONTACT 8
6.5 Assembly Screw Connection A B B C A D E www.interface.phoenixcontact.com Serial No. XXXXXXXX Figure Screw connection Figure Mounting and removing Insert the wire into the corresponding connection terminal block. Use a screwdriver to tighten the screw in the opening above the connection terminal block. Spring-cage connection: Mount the module on a 5 mm DIN rail according to EN 6075. When using the DIN rail connector, first place it into the DIN rail (see A C). It is used to bridge the power supply. It is also absolutely vital that you snap the module and the DIN rail connector into position in the correct direction: the snap-on foot should be at the bottom and the connector on the left. B A 6.6 Connecting the wires The MINI MCR-SL-PT00-UI-... is available in two connection variants: Screw terminal blocks (MINI MCR-SL-PT00-UI) Spring-cage terminal blocks (MINI MCR-SL-PT00-UI- SP) www.interface.phoenixcontact.com Serial No. XXXXXXXX Figure 5 Spring-cage connection Insert a screwdriver into the opening above the connection terminal block. Insert the wire into the corresponding connection terminal block. 099_en_06 PHOENIX CONTACT 9
7 Configuration If the modules are not configured (all DIP switches set to pos. 0), the module does not have a defined function until the DIP switches have been set. To order a product with an order configuration, please enter the desired configuration by referring to the order key. DIP switch S specifies the connection method, output signal range, and the start of the measuring range. DIP switch S specifies the measuring range final and error evaluation. DIP switch S can be used to select the voltage and current output. www.interface.phoenixcontact.com CE Meas. range: Out: Load: Test voltage: Amb.Temp.: Out U,I GND 9,...0VDC GND on S off Serial No. XXXXXXXX 5 OUT 6 7+ POWER 8- MINI MCR-SL-PT00-UI Ord.-No.: 8 6 5 PT00 - Transducer -50...850 C / -8...56 F 0()...0mA, 0()...5V, 0...0V I 500W / U ³ 0 kw,5kv,, 50 Hz, min. -0...+65 C / -...+9 F IN on off S 8 S 8 S S S Figure 6 Location of the DIP switches 099_en_06 PHOENIX CONTACT 0
7. Configuration table DIP S Connection Output signal range Start temperature method 5 OUT 6 7 8 [ C] [ F] -wire 0... 0 ma 0 -wire 0... 0 ma -0 -wire... 0 ma -0 - -wire 0... ma -0-0... 0 V -0-0 0... 0 V -50-58 0... 5 V -00-8... 5 V -50-8 DIP S 7 8 Cable break A Measuring range final +5% B Measuring range final +5% C Measuring range final +5% D Measuring range start DIP S OUT 0... 0 ma,... 0 ma, 0... 0 ma, 0... ma 0... 0 V, 0... 0 V, 0... 5 V,... 5 V = ON = OFF Measuring range Measuring range overrange underrange Short circuit Measuring range Measuring range start Measuring range start final +.5% Measuring range Measuring range Measuring range final +.5% start -.5% start -5% Measuring range final Measuring range start Measuring range final +5% Measuring range final Measuring range start Measuring range start DIP S Final temperature 5 6 [ C] [ F] 0 5 0 50 5 59 0 68 5 77 0 86 5 95 0 0 5 50 55 60 0 65 9 70 58 75 67 80 76 85 85 90 9 95 0 00 0 0 0 8 0 66 0 8 50 0 60 0 70 8 80 56 90 7 00 9 0 0 0 8 0 6 0 6 50 8 60 500 70 58 80 56 90 55 00 57 0 608 0 6 60 680 80 76 00 75 0 788 0 8 60 860 80 896 500 9 50 968 50 00 560 00 580 076 600 60 8 60 8 660 0 680 56 700 9 750 8 800 7 850 56 099_en_06 PHOENIX CONTACT
8 Diagnostics LED The LED indicates the following error states: LED flashes: Measuring range span < 50 K LED ON: Open circuit on the sensor side LED ON: Short-circuit on the sensor side LED ON: Measuring range overrange LED ON: Measuring range underrange 9 Connection/application example -Wire Connection Method For short distances (< 0 m). The RL and RL cable resistance are incorporated directly into the measurement result. -Wire Connection Method For long distances between the Pt 00-Sensor and the MINI analog module and different cable resistances (RL RL RL RL). IN IN Figure 7 Connection example -Wire Connection Method For long distances between the Pt00 sensor and the MINI Analog module. All cable resistances must have exactly the the same s to compensate for cable resistances (RL = RL = RL). Figure 9 Connection example IN Figure 8 Connection example 099_en_06 PHOENIX CONTACT GmbH & Co. KG 8 Blomberg Germany www.phoenixcontact.com