Interface technology and switching devices

Transcription

1 Highly compact signal conditioners - MI Analog Pro 3-way signal conditioners Page 326 Highly compact signal conditioners - MI Analog Pro Temperature transducers for resistance thermometers and thermocouples Page 330 Highly compact signal conditioners - MI Analog Pro Potiposition transducers Page 334 Highly compact signal conditioners - MI Analog Pro Supply components, fault monitoring module, marking material Page 336 Signal conditioners with PL d and SIL functional safety - MACX Safety Repeater power supply Page 342 Temperature transducers Page 343 Signal conditioners with PL d and SIL functional safety - MACX Safety Repeater power supplies, Ex i Page 344 Temperature transducers, Ex i Page 346 Energy and power measuring technology Software for usage data acquisition Page 348 Software for data logging Page 349 Energy and power measuring technology Pressure sensor with IO-Link Page 350 Current and voltage measuring technology PACT RCP... current transformers for retrofitting Page 353 Programmable logic relay system - PLC logic Logic modules Page 356 Accessories Page 358 Relay modules - RIFLE complete Fully mounted RIF-0 relay modules with solid-state relay and push-in connection Page 362 Relay modules - RIFLE complete Fully mounted RIF-1 relay modules with relay with detectable manual operation, status LED, and push-in connection Page PHOENIX CONTACT

2 Relay modules - PLC series With integrated solid-state relay Page 366 VARIOFACE system cabling VIP power cabling Universal front adapters for SIMATIC S7-300 Page 368 VARIOFACE system cabling VIP I/O modules Page 370 VIP interface module for Emerson DeltaV Page 372 VARIOFACE wiring interface VIP potential distributor with fuses Page 373 For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 323

3 Measurement and control technology - MI Analog Pro highly compact signal conditioners Easier than ever but slim as before The new highly compact MI Analog Pro signal conditioners offer the easiest installation and startup in a confined space. Easily accessible terminal points, current measurement during operation, and the unique FASTCON Pro plug-in connection technology make your work considerably easier. Choose the right MI Analog signal conditioner for your application: Analog /OUT Universal and standard 3-way signal conditioners 3-way repeater power supplies Temperature Universal measuring transducers for resistance thermometers and thermocouples Universal potiposition transducer Potiposition transducers with automatic potentiometer detection Accessories Supply components Fault monitoring module Marking material Surge protection, see Catalog 6 Easy installation in a confined space Thanks to the front orientation, all terminal points are easily visible and accessible at all times this not only saves time, but also space above and below devices All conductors can be fed individually and in any order, regardless of whether you start wiring from the input or output side The FASTCON Pro connection terminal blocks can be inserted and removed in any order Measure current signals during operation You can conveniently measure signals for startup and servicing during operation, thanks to integrated test disconnect terminal blocks: The circuit does not have to be separated in order to integrate the measuring device in the signal circuit By setting the plug to the disconnect position, signal circuits can be easily interrupted during servicing and startup Numerous parameterization options Easy DIP switch configuration Many of the MI Analog modules can be configured: the basic functions can be easily set using DIP switches without the need for any software. PC configuration for extended function and monitoring For extended functionality, you can configure the modules conveniently with the S port interface on your PC using one of the free software solutions. Smart configuration without accessories Place your smartphone on the device and establish a wireless connection via near field communication (NFC). Depending on the device type, the free MI Analog Pro app offers different functions. App functions via NFC communication Access to information Access module information DIP switch setting help Access module information Display DIP switch setting help on the smartphone Configuration via NFC Access module information Display DIP switch setting help Wireless configuration via smartphone 324 PHOENIX CONTACT

4 Measurement and control technology - MI Analog Pro highly compact signal conditioners Space savings of up to 65% Compared to other signal conditioners on the market with design widths up to 17.5 mm. Easy installation Easily visible and accessible terminal points and FASTCON Pro plug-in connection terminal blocks. Power bridging and fault monitoring The D rail connector simplifies supply and enables group error monitoring via remote diagnostics. Easy to start up and control Measure current signals during operation, without disconnecting current loops, plus optional disconnect function. Numerous parameterization options Easy configuration via DIP switches as well as extended configuration via software or smartphone app without additional accessories. Easy maintenance Large-surface marking areas for complete loop identification using standard marking material as well as constantly visible status LEDs in every module. Choice of connection technology Wiring with screw connection or fast and tool-free push-in technology. Optimum signal quality The latest transmission technology and safe electrical isolation between input, output, and supply with 3 kv test voltage. Suitable for any application Extended supply voltage and temperature range as well as multifunctional device types. For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 325

5 Measurement and control technology - MI Analog Pro highly compact signal conditioners Analog / Analog OUT 3-way signal conditioner Sensor / Field OUT PLC / DCS TI TI+ OUT U S 4-wire active passive U,I U, I+ OUT U, I GND U, I OUT U, I PWR+ PWR+ U,I U,I OUT FM POWER 4 8 PWR PWR FM PWR PWR+ Configurable, Up to 144 signal combinations Configurable, ultra-compact signal conditioner for electrical isolation, conversion, amplification, and filtering of standard analog signals Plug-in connection system Safe 3-way isolation Standard signal combinations configurable via DIP switches Power supply and fault monitoring possible via D rail connector Status LED Zone 2 Ex: Housing width 6.2 mm Input data U input I input Input signal 0 V... 5 V 1 V... 5 V -5 V... 5 V 0 ma ma 4 ma ma -20 ma ma 0 V V 2 V V -10 V V 0 V V 4 V V -20 V V 0 V V 4.8 V V -24 V V 0 V V 6 V V -30 V V Input resistance > 1000 kω approx. 63 Ω Output data U output I output Output signal 0 V... 5 V 1 V... 5 V -5 V... 5 V 0 V V 2 V V -10 V V 0 ma ma 4 ma ma Maximum output signal 22 ma No-load voltage < 17 V Short-circuit current < 32 ma Load R B 10 kω 600 Ω (at 20 ma) Ripple < 20 mv PP (at 600 Ω) < 20 mv PP (at 600 Ω) General data U output I output Supply voltage U B 9.6 V DC V DC Nominal supply voltage 24 V DC Current consumption 25 ma (current output, at 24 V DC incl. load) 54 ma (current output, at 12 V DC incl. load) Power consumption 800 mw (at I OUT = 20 ma, 9.6 V DC, 600 Ω load) Maximum transmission error 0.1% (of final value) Temperature coefficient 0.01%/K Limit frequency (3 db) 30 Hz (via DIP switch) Step response (10-90%) < 8.5 ms (with 30 Hz filter) Electrical isolation Reinforced insulation in accordance with IEC Test voltage, input/output/supply 3 kv (50 Hz, 1 min.) Degree of protection IP20 Ambient temperature (operation) -40 C C Mounting Any Housing material PBT Dimensions W/H/D 6.2/110.5/120.5 mm Push-in connection solid/stranded/awg mm²/ mm²/26-12 Screw connection solid/stranded/awg mm²/ mm²/26-16 EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X UL, USA / Canada 508 listing applied for Class I, Div. 2, Groups A, B, C, D T5 applied for GL GL applied for Description Type Order No. 3-way signal conditioner, for electrical isolation of analog signals 326 PHOENIX CONTACT Standard configuration Push-in connection MI MCR-2-UI-UI-PT Standard configuration Screw connection MI MCR-2-UI-UI Order configuration Push-in connection MI MCR-2-UI-UI-PT-C Order configuration Screw connection MI MCR-2-UI-UI-C

6 Measurement and control technology - MI Analog Pro highly compact signal conditioners Order key for MI-MCR-2-UI-UI...C 3-way signal conditioner (standard configuration entered as an example) Order No. Input Output Cut-off frequency / 03 / OUT01 / 5K MI-MCR-2- UI-UI-C MI-MCR-2- UI-UI-PT-C ma OUT ma 30 Hz ma OUT ma 5 khz V OUT V V OUT V V OUT V V OUT V V OUT V V OUT V V V ma V V V V V V V Signal combinations for MI-MCR-2-UI-UI-... signal conditioners Output Input ma ma V V V V V V ma X X X X X X X X ma X X X X X X X X ma X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X V X X X X X X X X For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 327

7 Measurement and control technology - MI Analog Pro highly compact signal conditioners Analog / Analog OUT 3-way signal conditioner Sensor / Field OUT PLC / DCS 5 TI+ OUT U S 4-wire active passive U+ U+ OUT I+ OUT U U OUT I PWR+ PWR+ U,I U,I OUT FM POWER 4 8 PWR PWR FM PWR PWR+ With fixed signal combinations Zone 2 Highly compact signal conditioner for electrical isolation, conversion, amplification, and filtering of standard analog signals Fixed signal combinations Plug-in connection system Safe 3-way isolation Power supply and fault monitoring possible via D rail connector Status LED Input data U input I input Input resistance approx. 100 kω approx. 63 Ω Output data U output I output Maximum output signal 11 V 22 ma No-load voltage < 17 V Short-circuit current < 15 ma Load R B 10 kω 600 Ω (at 20 ma) Ripple < 20 mv PP (at 10 kω) < 20 mv PP (at 600 Ω) General data Supply voltage U B 9.6 V DC V DC Nominal supply voltage 24 V DC Typ. current consumption 25 ma (at 24 V DC) Maximum transmission error 0.1% (of final value) Temperature coefficient 0.01%/K Limit frequency (3 db) approx. 30 Hz Step response (10-90%) approx. 10 ms Degree of protection IP20 Electrical isolation Reinforced insulation in accordance with IEC Test voltage, input/output/supply 3 kv (50 Hz, 1 min.) Ambient temperature (operation) -40 C C Housing material PBT Dimensions W/H/D 6.2/110.5/120.5 mm Push-in connection solid/stranded/awg mm²/ mm²/26-12 Screw connection solid/stranded/awg mm²/ mm²/26-16 EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X UL, USA / Canada 508 listing applied for Class I, Div. 2, Groups A, B, C, D T5 applied for GL GL applied for Description Input signal Output signal Type Order No. 3-way signal conditioner, for electrical isolation of analog signals Push-in connection V ma MI MCR-2-U-I0-PT Screw connection V ma MI MCR-2-U-I Push-in connection V ma MI MCR-2-U-I4-PT Screw connection V ma MI MCR-2-U-I Push-in connection ma V MI MCR-2-I0-U-PT Screw connection ma V MI MCR-2-I0-U Push-in connection ma V MI MCR-2-I4-U-PT Screw connection ma V MI MCR-2-I4-U Push-in connection Screw connection ma, ma ma, ma ma, ma ma, ma MI MCR-2-I-I-PT MI MCR-2-I-I Push-in connection V, V Screw connection V, V V, V V, V MI MCR-2-U-U-PT MI MCR-2-U-U PHOENIX CONTACT

8 Analog / Analog OUT repeater power supplies Interface technology and switching devices Measurement and control technology - MI Analog Pro highly compact signal conditioners Sensor / Field OUT PLC / DCS POWER I I FM POWER OUT 2-wire PWR OUT I PWR wire 3 OUT I+ 4 OUT I OUT I+ 3 U S 4-wire 4 OUT I TI+ TI PWR OUT + OUT I+ active 2 I 6 OUT I TI I+ PWR+ 4 8 I PWR FM PWR PWR+ Zone passive Repeater power supply with HART transmission Highly-compact repeater power supply for electrical isolation, conversion, amplification, and filtering of standard analog signals Supply of 2-wire and passive 3-wire sensors Can also be used as an isolator without supply Plug-in connection system Safe 3-way isolation Bidirectional HART transmission as an option Power supply and fault monitoring possible via D rail connector Status LED Housing width 6.2 mm Input data Input signal ma, isolator operation/ ma Input resistance approx. 68 Ω Transmitter supply voltage > 19.5 V Output data Output signal ma/ ma Maximum output signal No-load voltage < 20 V Load R B 600 Ω (at 20 ma) Ripple < 20 mv PP (at 600 Ω) General data Supply voltage U B 9.6 V DC V DC Nominal supply voltage 24 V DC Current consumption 25 ma (at 24 V DC and in isolator operation) Power consumption 1400 mw (at I OUT = 20 ma, 9.6 V DC, 600 Ω load) Maximum transmission error 0.1% (of final value) Temperature coefficient 0.01%/K, Limit frequency (3 db) > 1.75 khz (typ.) Communication HART specification in both operating modes (RPSS isolator/rpss repeater power supply) Step response (10-90%) < 200 µs (typ.) Electrical isolation Reinforced insulation in accordance with IEC Test voltage, input/output/supply Degree of protection IP20 Ambient temperature (operation) -40 C C Mounting Any Housing material PBT Dimensions W/H/D 6.2/110.5/120.5 mm Push-in connection solid/stranded/awg mm²/ mm²/26-12 Screw connection solid/stranded/awg mm²/ mm²/26-16 EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X UL, USA / Canada 508 listing applied for Class I, Div. 2, Groups A, B, C, D T5 applied for GL GL applied for Description Type Order No. Repeater power supply with HART transmission Push-in connection MI MCR-2-RPSS-I-I-PT Screw connection MI MCR-2-RPSS-I-I For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 329

9 Measurement and control technology - MI Analog Pro highly compact signal conditioners Temperature Temperature transducers for resistance thermometers Sensor / Field OUT PLC / DCS ϑ ϑ ϑ 1 2 S-Port TI OUT U, I+ active 2 6 OUT U, I 5 6 passive PWR+ U,I FM POWER OUT 4 4 FM PWR PWR+ 8 PWR Universal measuring transducer for resistance thermometers Universally configurable, highly compact temperature transducer for electrical isolation, conversion, amplification, and filtering of resistance thermometer and remote resistance-type sensor signals For 2, 3 or 4-wire sensors according to IEC 751, JIS, GOST Plug-in connection system Safe 3-way isolation Standard signal combinations configurable via DIP switches Freely configurable via software or smartphone app Power supply and fault monitoring possible via D rail connector Status and error indicator LEDs Zone 2 Input data Input signal (can be configured using DIP switches) Temperature range Ex: Housing width 6.2 mm Pt, Ni, Cu sensors : 2, 3, 4-wire -200 C C (range depending on the sensor type) Measuring range span 20 K Linear resistance measuring range 0 Ω Ω (Minimum measuring span: 10% of the selected measuring range) Output data U output I output Output signal V/ V ma/ ma V/ V ma/ ma Maximum output signal approx V 24.6 ma Load R B 10 kω 600 Ω (at 20 ma) Ripple < 20 mv PP < 20 mv PP (at 600 Ω) General data Supply voltage U B 9.6 V DC V DC Current consumption 32 ma (at 24 V DC) Power consumption 850 mw (at I OUT = 20 ma, 9.6 V DC, 600 Ω load) Transmission error 0.1% * 350 K/set measuring range; 0.1% > 350 K (Pt/Ni) 0.3% * 200 K/set measuring range; 0.3% > 200 K (Cu) Temperature coefficient 0.01%/K Step response (0 99%) Typ. 200 ms (2-wire) Typ. 500 ms (3-wire) Typ. 500 ms (4-wire) Electrical isolation Reinforced insulation in accordance with IEC Test voltage, input/output/supply 3 kv (50 Hz, 1 min.) Ambient temperature (operation) -40 C C Housing material PBT Dimensions W/H/D 6.2/110.5/120.5 mm Push-in connection solid/stranded/awg mm²/ mm²/26-12 Screw connection solid/stranded/awg mm²/ mm²/26-16 EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X UL, USA / Canada 508 listing applied for Class I, Div. 2, Groups A, B, C, D T5 applied for GL GL applied for Description Type Order No. Temperature transducers for resistance thermometers Standard configuration Push-in connection MI MCR-2-RTD-UI-PT Standard configuration Screw connection MI MCR-2-RTD-UI Order configuration Push-in connection MI MCR-2-RTD-UI-PT-C Order configuration Screw connection MI MCR-2-RTD-UI-C Accessories Programming adapter for configuring modules with S-PORT interface IFS-USB-PROG-ADAPTER PHOENIX CONTACT

10 Measurement and control technology - MI Analog Pro highly compact signal conditioners Order key for MI-MCR-2-RTD-UI...C temperature transducer (standard configuration entered as an example) Order No. Sensor type Connection technology Measuring range Measuring Output Start End unit Output signal Start End / PT100 / 3 / -50 / 150 / C / I / 4.0 / 20.0 / MI-MCR-2- RTD-UI-C MI-MCR-2- RTD-UI-PT-C PT100 Pt 100 IEC wire freely selectable freely selectable C C I I ma ma PT200 Pt 200 IEC wire between between F F U U I: freely I: freely -200 C C -200 C C PT500 Pt 500 IEC wire selectable selectable (measuring (measuring between PT1000 Pt 1000 IEC 751 between range limits range limits ma ma depend on sensor type) depend on sensor type) PT100G Pt 100 GOST ( = ) PT1000G Pt 1000 GOST ( = ) PT100J Pt 100 JIS C1604/1997 PT1000J Pt 1000 JIS C1604/1997 NI100 Ni 100 D NI1000 Ni 1000 D CU50 Cu 50 GOST ( = ) CU100 Cu 100 GOST ( = ) CU53 Cu 53 GOST ( = ) U: freely selectable between V U: freely selectable between V Failure information Behavior in the event of an error Open circuit Short circuit Overrange Underrange... / NE43DO / 0.0 / 0.0 / 0.0 / 0.0 FD Freely definable ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) Note: failure information according to NE 43 can only be selected for ma output NE43UP NE 43 upscale 21.5 ma 21.5 ma 21.5 ma 21.5 ma NE43DO NE 43 downscale 3.5 ma 3.5 ma 3.5 ma 3.5 ma NE430 NE 43 0 ma 0 ma 0 ma 0 ma 0 ma NE43UD NE 43 upscale/downscale 3.5 ma 3.5 ma 21.5 ma 21.5 ma Sensor types and measuring ranges for MI-MCR-2-RTD-UI-... temperature transducers Sensor type Standard Measuring range Smallest measuring Adjustable using: span Pt100 IEC 751 = GOST ( = ) -200 C C 20 K DIP switch Pt200 IEC 751 = GOST ( = ) -200 C C 20 K DIP switch Pt500 IEC 751 = GOST ( = ) -200 C C 20 K Software or smartphone app Pt1000 IEC 751 = GOST ( = ) -200 C C 20 K Software or smartphone app Pt100 GOST ( = ) -200 C C 20 K Software or smartphone app Pt1000 GOST ( = ) -200 C C 20 K Software or smartphone app Pt100 JIS C C C 20 K Software or smartphone app Pt1000 JIS C C C 20 K Software or smartphone app Ni100 D C C 20 K Software or smartphone app Ni1000 D C C 20 K Software or smartphone app Cu50 GOST ( = ) -180 C C 20 K Software or smartphone app Cu100 GOST ( = ) -180 C C 20 K Software or smartphone app Cu53 GOST ( = ) -50 C C 20 K Software or smartphone app Customer-specific characteristic curves -200 C C 20 K Software or smartphone app For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 331

11 Measurement and control technology - MI Analog Pro highly compact signal conditioners Temperature Temperature transducers for thermocouples Sensor / Field OUT PLC / DCS TC 1 2 S-Port TI OUT U, I+ active 2 6 OUT U, I 5 6 passive PWR+ U,I FM POWER OUT 4 FM PWR PWR+ 8 PWR Universal measuring transducer for thermocouples Universally configurable, highly compact temperature transducer for electrical isolation, conversion, amplification, and filtering of thermocouple signals For thermocouples according to IEC 584 and GOST Internal cold junction compensation Plug-in connection system Safe 3-way isolation Standard signal combinations configurable via DIP switches Freely configurable via software or smartphone app Power supply and fault monitoring possible via D rail connector Status and error indicator LEDs Zone 2 Input data Input signal (can be configured using DIP switches) Temperature range Ex: Housing width 6.2 mm B, E, J, K, N, R, S, T, L, U, A-1, A-2, A-3, M, L -250 C C (range depending on the sensor type) Measuring range span min. 50 K Output data U output I output Output signal (configurable using the DIP switch) V/ V ma/ ma V/ V ma/ ma Maximum output signal approx V 24.6 ma No-load voltage < 17.5 V Short-circuit current < 31.5 ma Load R B 10 kω 600 Ω (at 20 ma) Ripple < 20 mv PP < 20 mv PP (at 600 Ω) General data Supply voltage U B 9.6 V DC V DC Current consumption 32 ma (at 24 V DC) Power consumption 850 mw (at I OUT = 20 ma, 9.6 V DC, 600 Ω load) Transmission error 0.1% * 600 K/set measuring range; 0.1% > 600 K (E, J, K, N, T, L, U, M Gost, L Gost) 0.2% * 600 K/set measuring range; 0.2% > 600 K (B, R, S, A1, A2, A3) Cold junction errors (0,2 K * ΔT) ( typ. < 2 K ) Temperature coefficient 0.01%/K Step response (0 99%) Typ. 400 ms Electrical isolation Reinforced insulation in accordance with IEC Test voltage, input/output/supply 3 kv (50 Hz, 1 min.) Ambient temperature (operation) -40 C C Housing material PBT Dimensions W/H/D 6.2/110.5/120.5 mm Push-in connection solid/stranded/awg mm²/ mm²/26-12 Screw connection solid/stranded/awg mm²/ mm²/26-16 EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X UL, USA / Canada 508 listing applied for Class I, Div. 2, Groups A, B, C, D T5 applied for GL GL applied for Description Type Order No. Temperature transducers for thermocouples Standard configuration Push-in connection MI MCR-2-TC-UI-PT Standard configuration Screw connection MI MCR-2-TC-UI Order configuration Push-in connection MI MCR-2-TC-UI-PT-C Order configuration Screw connection MI MCR-2-TC-UI-C Accessories Programming adapter for configuring modules with S-PORT interface IFS-USB-PROG-ADAPTER PHOENIX CONTACT

12 Measurement and control technology - MI Analog Pro highly compact signal conditioners Order key for MI-MCR-2-TC-UI...C temperature transducer (standard configuration entered as an example) Order No. Sensor type Cold junction compensation Measuring range Measuring Output Start End unit Output signal Start End / J / 1 / -200 / 1200 / C / I / 4.0 / 20.0 / MI-MCR-2- TC-UI-C MI-MCR-2- TC-UI-PT-C B B IEC (Pt30Rh-Pt6Rh) 0 OFF freely selectable freely selectable C C I I ma ma E E IEC (NiCr-CuNi) 1 ON between between F F U U I: freely I: freely -250 C C -250 C C J J IEC (Fe-CuNi) selectable selectable (measuring range limits (measuring range limits between K K IEC (NiCr-Ni) between depend on depend on ma ma sensor type) sensor type) N N IEC (NiCrSi-NiSi) R R IEC (Pt13Rh-Pt) S S IEC (Pt10Rh-Pt) T T IEC (Cu-CuNi) L L D (Fe-CuNi) U U D (Cu-CuNi) A1G A-1 GOST A2G A-2 GOST A3G A-3 GOST MG M GOST LG L GOST U: freely selectable between V U: freely selectable between V Failure information Behavior in the event of an error Open circuit Overrange Underrange... / NE43DO / 0.0 / 0.0 / 0.0 FD Freely definable ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) Note: failure information according to NE 43 can only be selected for ma output NE43UP NE 43 upscale 21.5 ma 21.5 ma 21.5 ma NE43DO NE 43 downscale 3.5 ma 3.5 ma 3.5 ma NE430 NE 43 0 ma 0 ma 0 ma 0 ma NE43UD NE 43 upscale/downscale 3.5 ma 21.5 ma 21.5 ma Sensor types and measuring ranges for MI-MCR-2-TC-UI-... temperature transducers Sensor type Standard Measuring range Smallest measuring Adjustable using: span B IEC C C 50 K Software or smartphone app E IEC C C 50 K Software or smartphone app J IEC C C 50 K DIP switch K IEC C C 50 K DIP switch N IEC C C 50 K Software or smartphone app R IEC C C 50 K Software or smartphone app S IEC C C 50 K Software or smartphone app T IEC C C 50 K Software or smartphone app L D C C 50 K Software or smartphone app U D C C 50 K Software or smartphone app A-1 GOST C C 50 K Software or smartphone app A-2 GOST C C 50 K Software or smartphone app A-3 GOST C C 50 K Software or smartphone app M GOST C C 50 K Software or smartphone app L GOST C C 50 K Software or smartphone app Customer-specific characteristic curves -250 C C 50 K Software or smartphone app For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 333

13 Measurement and control technology - MI Analog Pro highly compact signal conditioners Potentiometers, potiposition transducers Sensor / Field OUT PLC / DCS 1 2 S-Port TI OUT U, I+ active 2 6 OUT U, I 5 6 passive PWR+ R U,I OUT FM POWER 4 FM PWR PWR+ 8 PWR Configurable, automatic potentiometer detection Universally configurable, highly compact potiposition transducer for electrical isolation, conversion, amplification, and filtering of potentiometer signals For potentiometers from 100 Ω to 100 kω Automatic potentiometer detection without manual adjustment Plug-in connection system Safe 3-way isolation Standard signal combinations configurable via DIP switches Freely configurable via software or smartphone app Power supply and fault monitoring possible via D rail connector Status and error indicator LEDs Zone 2 Ex: Housing width 6.2 mm Input data Potentiometer 100 Ω kω Reference voltage source - Output data U output I output Output signal V/ V ma/ ma V/ V ma/ ma Maximum output signal approx V 24.6 ma No-load voltage < 17.5 V Short-circuit current < 31.5 ma Load R B 10 kω 600 Ω (at 20 ma) Ripple < 20 mv PP (at 10 kω) < 20 mv PP Behavior in the event of a sensor error (configurable) General data Supply voltage U B 9.6 V DC V DC Nominal supply voltage 24 V DC Current consumption 33 ma (at 24 V DC) Power consumption 850 mw (at I OUT = 20 ma, 9.6 V DC, 600 Ω load) Maximum transmission error < 0.1% (R < 240 Ω = < 0,2%) Temperature coefficient 0.01%/K Step response (0 99%) - Electrical isolation Reinforced insulation in accordance with IEC Test voltage, input/output/supply 3 kv (50 Hz, 1 min.) Degree of protection IP20 Ambient temperature (operation) -40 C C Mounting Any Housing material PBT Dimensions W/H/D 6.2/110.5/120.5 mm Push-in connection solid/stranded/awg mm²/ mm²/26-12 Screw connection solid/stranded/awg mm²/ mm²/26-16 EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X UL, USA / Canada 508 listing applied for Class I, Div. 2, Groups A, B, C, D T5 applied for GL GL applied for Description Type Order No. Potiposition transducer Standard configuration Push-in connection MI MCR-2-POT-UI-PT Standard configuration Screw connection MI MCR-2-POT-UI Order configuration Push-in connection MI MCR-2-POT-UI-PT-C Order configuration Screw connection MI MCR-2-POT-UI-C Accessories Programming adapter for configuring modules with S-PORT interface IFS-USB-PROG-ADAPTER PHOENIX CONTACT

14 Measurement and control technology - MI Analog Pro highly compact signal conditioners Order key for MI-MCR-2-POT-UI...C 3-way signal conditioner (standard configuration entered as an example) Order No. Automatic potentiometer detection Output Filter Open circuit detect Output signal Start End / AUTO / I / 1 / ON / MI-MCR-2- POT-UI-C MI-MCR-2- POT-UI-PT-C AUTO ON I I ma ma 1 ON ON OFF OFF U U I: freely selectable between ma U: freely selectable between V I: freely selectable between ma U: freely selectable between V 2 OFF OFF Failure information Behavior in the event of an error Open circuit slider Input open (no potentiometer connected) Overrange Underrange... / NE43DO / 0.0 / 0.0 / 0.0 / 0.0 FD Freely definable ma I: freely selectable between ma U: freely selectable between V (only if open circuit detection is on) (signal type corresponds to selected output signal) ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) ma I: freely selectable between ma U: freely selectable between V (signal type corresponds to selected output signal) Note: failure information according to NE 43 can only be selected for ma output NE43UP NE 43 upscale 21.5 ma 21.5 ma 21.5 ma 21.5 ma NE43DO NE 43 downscale 3.5 ma 3.5 ma 3.5 ma 3.5 ma NE430 NE 43 0 ma 0 ma 0 ma 0 ma 0 ma NE43UD NE 43 upscale/downscale 3.5 ma 3.5 ma 21.5 ma 21.5 ma For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 335

15 Measurement and control technology - MI Analog Pro highly compact signal conditioners Accessories ME 6,2 TBUS... D rail connector For bridging the supply voltage Reduces wiring costs Module replacement without interrupting the supply to the remaining modules (hot swappable) One D rail connector for two MI Analog modules Only distinguished by color coding For bridging the supply voltage For bridging the supply voltage Description Type Order No. Type Order No. D rail connector (TBUS), for bridging the supply voltage, can be snapped onto 35 mm D rails as per EN 60715, with UL approval Color: green ME 6,2 TBUS-2 1,5/5-ST-3,81 GN Color: gray ME 6,2 TBUS-2 1,5/5-ST-3,81 GY Accessories Power terminal blocks Power terminal block for supplying the supply voltage to the D rail connector Plug-in connection system Increased output current of 3.2 A Monitoring of supplies in combination with the fault monitoring module Flexible redundant supply from one or both module sides Status and error indicator LEDs +9,6 V +30 V +9,6 V +30 V OUT FM PWR 1 PWR 1 OUT-FM PWR 2 PWR 2 OUT-FM PWR OUT Zone 2 +9,6 V +30 V +9,6 V +30 V Redundant supply for existing 24 V 336 PHOENIX CONTACT Input data/output data Input voltage range 9.9 V DC V DC Output voltage (Input voltage V) Output current 3.2 A General data Ambient temperature (operation) -40 C C Housing material PBT EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X UL, USA / Canada 508 listing applied for Class I, Div. 2, Groups A, B, C, D T5 applied for GL GL applied for Description Type Order No. MI Analog Pro power terminal block Push-in connection MI MCR-2-PTB-PT Screw connection MI MCR-2-PTB

16 Accessories ME 17,5 TBUS-... D rail connector For bridging the supply voltage when using a MI POWER system power supply Notes: If the system power supply is used, two ME 17,5 TBUS D rail connectors are required. This allows you to establish the connection to the ME 6,2 TBUS D rail connector of the MI Analog system and provide an effective power supply. Interface technology and switching devices Measurement and control technology - MI Analog Pro highly compact signal conditioners For system power supply Description Type Order No. D rail connector, for bridging the supply voltage, can be snapped onto 35 mm D rails as per EN 60715, with UL approval, two pieces are required per system power supply ME 17,5 TBUS 1,5/ 5-ST-3,81 GN Accessories System power supply For supplying the supply voltage via the D rail connector where AC voltages are available V AC nominal input voltage range 24 V DC output voltage For up to 60 MI Analog modules For up to 1.5 A, secondary Status and error signaling via diagnostic LEDs D H W For applications with local voltages of over 100 V Description Type Order No. System power supply, primary-switched, with zone 2 approval. Further information can be found in Catalog 6, Surge protection and power supplies. System power supply, primary-switched (not for zone 2!) Further information can be found in Catalog 6, Surge protection and power supplies. MI-PS AC/24DC/1.5/EX MI-SYS-PS AC/24DC/ For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 337

17 Measurement and control technology - MI Analog Pro highly compact signal conditioners Accessories Feed-through terminal blocks Feed-through terminal block for 1:1 forwarding of signals that are already electrically isolated in the MI Analog Pro group Plug-in connection system Sensor / Field OUT 1 5 OUT 2 6 OUT 3 7 OUT PLC / DCS 4 8 OUT 1:1 connection General data Degree of protection IP20 Ambient temperature (operation) -40 C C Mounting Any Housing material PBT Dimensions W/H/D 6.2/110.5/120.5 mm Screw connection solid/stranded/awg mm²/ mm²/26-16 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X GL GL applied for Description Type Order No. MI Analog Pro feed-through terminal block Screw connection MI MCR-2-TB Accessories Error message modules Fault monitoring module for evaluating and reporting group errors from the fault monitoring system Monitoring of up to 115 connected MI Analog Pro modules Plug-in connection system Monitoring of supply voltages of MI MCR-2-PTB(-PT) power terminal blocks Drawing off the supply is possible Fault signaling via an N/C contact Status and error indicator LEDs +9,6 V +30 V +9,6 V +30 V PWR 1 OUT RC 2 6 OUT RC PWR 2 PWR OUT 4 8 FM PWR PWR+ OUT FAULT CONTACT Zone 2 +9,6 V +30 V Group error message and supply monitoring Input data/output data Input signal 9.9 V DC V DC Output signal 9.6 V DC V DC Switching output Max. switching voltage 30 V DC Max. switching current 50 ma General data Test voltage input/output 1.5 kv AC (50 Hz, 1 min.) EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na IIC T4 Gc X UL, USA / Canada 508 listing applied for Class I, Div. 2, Groups A, B, C, D T5 applied for GL GL applied for 338 PHOENIX CONTACT Description Type Order No. MI Analog Pro error signaling module Push-in connection MI MCR-2-FM-RC-PT Screw connection MI MCR-2-FM-RC

18 Accessories Programming adapter Interface technology and switching devices Measurement and control technology - MI Analog Pro highly compact signal conditioners IFS-USB-PROG-ADAPTER programming adapter for configuring Phoenix Contact TERFACE modules with S-PORT interface. The adapter is used with FDT/DTM software or ANALOG-CONF software. For programming MACX Analog and MI Analog. General data EMC note Class A product, see page 443 Description Type Order No. Programming adapter for configuring modules with S-PORT interface IFS-USB-PROG-ADAPTER Accessories Marking label for transparent cover Snap-in labels and adhesive labels with large-area for marking For snapping into or sticking onto MI Analog Pro covers, without overlapping the status and error LEDs The sheets can be marked quickly and easily using the BLUEMARK CLED and the THERMOMARK CARD... They can also be custom printed according to customer requirements Description Color Type Order No. Type Order No. UniCard, can be labeled with THERMOMARK CARD and BLUEMARK Lettering field size: 30 x 5 mm white UCT-EM (30X5) Lettering field size: 30 x 5 mm white UCT-EM (30X5) CUS section, lettering field size: 15 x 5 mm white UC-EMLP (15X5) section, lettering field size: 15 x 5 mm white UC-EMLP (15X5) CUS Self-adhesive marker strips, unprinted, continuous, material off the roll, for marking with thermal transfer printer, can be separated using cutter, pitch as desired, strip length of up to 1000 mm, 10 strips, strip height of 5.0 mm, 1 roll = 90 m white SK 5,0 WH:REEL For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 339

19 Measurement and control technology - signal conditioners with PL and SIL functional safety - MACX Safety Integrate analog signals safely Integrate analog signals easily into your safety application according to the Machinery Directive. The MACX Safety analog signal conditioners are certified according to EN ISO with performance level PL d. Ex i signals MACX Safety Ex enables the easy and safe processing of intrinsically safe analog signals according to the Machinery Directive. Cost savings Direct safe shutdown without an additional safety controller or in conjunction with a small-scale controller from Phoenix Contact offers a clear cost advantage Further cost savings can be made thanks to easy configuration and easy integration in the safety chain Versions with push-in technology save installation time Choose the right MACX Safety signal conditioner for your application: Analog ma repeater power supplies and input signal conditioners with 2 electrically isolated outputs Temperature Universal temperature transducers for resistance thermometers, resistance-type sensors, potentiometers, thermocouples, and mv sources with safe limit value relay Functional safety from the initial idea to the finished product Phoenix Contact meets the requirements of functional safety according to IEC in a standardized development process. Here, all fault avoidance and fault control measures are taken into consideration, from the very development and production of a device right up to device operation. The devices are examined by an independent test center. D rail connector-compatible The D rail connector enables the modular bridging of the 24 V supply voltage. Wide range supply The modules featuring a wide range supply (...-UP) can be used in all power supply networks the world over without the need for additional power supply units. 340 PHOENIX CONTACT

20 Measurement and control technology - signal conditioners with PL and SIL functional safety - MACX Safety Safe and reliable functions Consistent PL d and SIL certification. This ensures the highest level of reliability and safety for your systems. Precise transmission and high operational reliability Thanks to patented transmission concept Safe electrical isolation. Easy integration with Sistema Easy integration into the safety chain via Sistema. The required data is already stored in Sistema. Easy configuration and monitoring Easy configuration and monitoring with the ANALOG-CONF stand-alone software with integrated monitoring function or with FDT/DTM. Easy to combine Analog signals, whether passive or active, can be easily combined with other safety modules. Easy-maintenance connection technology Plug-in connection terminal blocks with screw connection or fast push-in technology coded, with integrated sockets. Precise transmission, long service life Patented circuit concepts ensure precise signal transmission and minimal selfheating. Even for the Ex area Maximum explosion protection for all Ex zones with the MACX Safety Ex range as associated intrinsically safe equipment and for installation in zone 2. Direct safety shutdown Simple and direct shutdown for small applications is possible without an expensive safety controller or in conjunction with a small-scale controller. For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 341

21 Measurement and control technology - signal conditioners with PL and SIL functional safety - MACX Safety Analog Repeater power supplies Sensor / Field OUT PLC / DCS 2-wire OUT passive POWER OUT1 I I I OUT2 POWER U S or 4-wire GND +24V Power OUT GND V 1.1 Zone 2 Div passive Repeater power supply and input signal conditioner, with two electrically isolated outputs ma input, powered and not powered Two electrically isolated ma (active) outputs PL d according to EN ISO Up to SIL 2 according to EN Installation in zone 2 possible Plug-in screw and push-in connection technology 4-way electrical isolation Bidirectional HART communication possible Power supply via D rail connector possible Housing width 12.5 mm Input data Input signal 4 ma ma/4 ma ma Transmitter supply voltage > 21.5 V (at 20 ma) Voltage drop < 3.9 V (in input signal conditioner operation) Output data Output signal (per output) 4 ma ma (active) Load < 450 Ω (at 20 ma) Output ripple < 20 mv rms General data Supply voltage range 19.2 V DC V DC (24 V DC (-20% %)) Current consumption < 75 ma (at 24 V DC) Power dissipation < 1.45 W (at 24 V DC/20 ma) Temperature coefficient < 0.01%/K Step response (10-90%) < 1.3 ms (for 4 ma ma step) Transmission error, typical < 0.05% (of final value) Maximum transmission error < 0.1% (of final value) Under-/overload range According to NE 43 Electrical isolation Input/output/power supply 300 V rms (rated insulation voltage (surge voltage category II; pollution degree 2, safe isolation as per EN )) 2.5 kv (50 Hz, 1 min., test voltage) Output 1/output kv AC (50 Hz, 1 min., test voltage) Ambient temperature range -20 C C (any mounting position) Status indication Green LED (PWR supply voltage) SMART communication (per output) Yes Protocols supported HART Housing material PA 66-FR Dimensions W/H/D 12.5/99/114.5 mm Screw connection solid/stranded/awg mm²/ mm²/24-14 Spring-cage connection (solid/stranded/awg) mm²/ mm²/24-16 EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant, additionally EN ATEX II 3 G Ex na IIC T4 Gc X SIL in accordance with IEC Performance level according to ISO PLd Description Type Order No. Repeater power supplies and input signal conditioners, signal duplicator, with performance level Screw connection MACX PL-RPSSI-2I Spring-cage connection MACX PL-RPSSI-2I-SP PHOENIX CONTACT

22 Temperature, temperature transducer Interface technology and switching devices Measurement and control technology - signal conditioners with PL and SIL functional safety - MACX Safety POWER I OUT Input for resistance thermometers, thermocouples, resistance-type sensors, potentiometers, mv sources A safety-related limit value relay, by bridging two relays Differential measurement possible with Pt 100 An additional limit value relay for non-safety-related function PL d according to EN ISO Up to SIL 2 according to EN Configuration via software (ANALOG-CONF or FDT/DTM) Cold junction compensation with separate plug Wide range power supply V AC/DC Status indicators for supply voltage, cable, sensor, and module errors Installation in zone 2 possible Plug-in screw and push-in connection technology Sensor /Field TC - + Poti ϑ RTD ϑ ϑ Input data Resistance thermometers Thermocouple sensors Resistor Potentiometer Voltage Output data Output signal Maximum output signal Load R B Behavior in the event of a sensor error Switching output Contact type Contact material Max. switching voltage Max. switching current General data Supply voltage range Power consumption Temperature coefficient Maximum transmission error Electrical isolation OUT Power 24V...230V AC/DC GND 3.3 I OUT NC Zone 2 Div PLC /DCS passive DI DI Input/output/power supply Universal, with limit value relays, wide range power supply Ex: Housing width 35 mm Pt, Ni, Cu sensors: 2, 3, 4-wire B, E, J, K, N, R, S, T, L, U, CA, DA, A1G, A2G, A3G, MG, LG 0 Ω kω 0 Ω kω mv mv 4 ma ma 22 ma 600 Ω (at 20 ma) According to NE 43 or freely configurable Relay output 2 PDT AgSnO 2, hard gold-plated 250 V AC (250 V DC) 2 A (250 V AC)/2 A (28 V DC) 24 V V AC/DC (-20%/+10%, 50/60 Hz) < 2.4 W 0.01%/K 0.1% (e.g. for Pt 100, 300 K span, ma) 300 V rms (rated insulation voltage (surge voltage category II; pollution degree 2, safe isolation as per EN )) 2.5 kv (50 Hz, 1 min., test voltage) Input/output 375 V (peak value in accordance with EN ) Input/power supply 375 V (peak value in accordance with EN ) Input/switching output 375 V (peak value in accordance with EN ) Ambient temperature range -20 C C Humidity Typ. 5%... 95% (non-condensing) Housing material PA 66-FR Inflammability class in acc. with UL 94 V0 Dimensions W/H/D 35/99/114.5 mm Screw connection solid/stranded/awg mm²/ mm²/24-14 Spring-cage connection (solid/stranded/awg) mm²/ mm²/24-16 EMC note Class A product, see page 443 Conformance / approvals Conformance CE-compliant ATEX II 3 G Ex na nc ic IIC T4 Gc X IECEx Ex na nc ic IIC T4 Gc X SIL in accordance with IEC Performance level according to ISO PLd Description Type Order No. Temperature transducer and threshold value switch with performance level Screw connection MACX PL-T-UIREL-UP Spring-cage connection MACX PL-T-UIREL-UP-SP Accessories Programming adapter for configuring modules with S-PORT interface Plug with 50 Ω resistor, for current signals between +20 ma and -20 ma IFS-USB-PROG-ADAPTER MACX MCR-I For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 343

23 Measurement and control technology - signal conditioners with PL and SIL functional safety - MACX Safety Analog Repeater power supply, Ex i Sensor / Field OUT PLC / DCS AI passive OUT POWER OUT1 I I I OUT2 POWER or Zone 0,1,2 Zone 20,21,22 Div. 1, GND +24V Power OUT V 1.1 Zone 2 Div. 2 passive GND Repeater power supply and input signal conditioner, with two electrically isolated outputs ma input, [Ex ia], powered and not powered Two electrically isolated ma (active) outputs PL d according to EN ISO Up to SIL 2 according to EN Installation in zone 2 possible Plug-in screw and push-in connection technology 4-way electrical isolation Bidirectional HART communication possible Power supply via D rail connector possible Housing width 12.5 mm Input data Input signal 4 ma ma/4 ma ma Transmitter supply voltage > 16 V (at 20 ma) Voltage drop < 3.9 V (in input signal conditioner operation) Output data Output signal (per output) 4 ma ma (active) Load < 450 Ω (at 20 ma) Output ripple < 20 mv rms General data Supply voltage range 19.2 V DC V DC (24 V DC (-20% %)) Current consumption < 75 ma (24 V DC/ 20 ma) Power dissipation < 1.45 W (24 V DC/ 20 ma) Temperature coefficient < 0.01%/K Step response (10-90%) < 1.3 ms (for 4 ma ma step) Transmission error, typical < 0.05% (of final value) Maximum transmission error < 0.1% (of final value) Under-/overload range According to NE 43 Electrical isolation Input/output/power supply 300 V rms (rated insulation voltage (surge voltage category II; pollution degree 2, safe isolation as per EN )) 2.5 kv (50 Hz, 1 min., test voltage) Input/output 375 V (peak value in accordance with EN ) Input/power supply 375 V (peak value in accordance with EN ) Output 1/output kv AC (50 Hz, 1 min., test voltage) Ambient temperature range -20 C C (any mounting position) Status indication Green LED (PWR supply voltage) SMART communication (per output) Yes Protocols supported HART Housing material PA 66-FR Dimensions W/H/D 12.5/99/114.5 mm Screw connection solid/stranded/awg mm²/ mm²/24-14 Spring-cage connection (solid/stranded/awg) mm²/ mm²/24-16 EMC note Class A product, see page 443 Safety data as per ATEX Max. output voltage U o 25.2 V Max. output current I o 93 ma Max. output power P o 587 mw Maximum voltage U m 253 V AC (125 V DC) Conformance / approvals Conformance CE-compliant, additionally EN ATEX IECEx SIL in accordance with IEC Performance level according to ISO PLd II (1) G [Ex ia Ga] IIC/IIB II (1) D [Ex ia Da] IIIC II 3 (1)G Ex na [ia Ga] IIC/IIB T4 Gc [Ex ia Ga] IIC/IIB, [Ex ia Da], Ex na [ia Ga] IIC/IIB T4 Gc Description Type Order No. Repeater power supplies and input signal conditioners, signal duplicator, with performance level, intrinsically safe input Screw connection MACX PL-EX-RPSSI-2I Spring-cage connection MACX PL-EX-RPSSI-2I-SP PHOENIX CONTACT

24 Analog Repeater power supply, Ex i Interface technology and switching devices Measurement and control technology - signal conditioners with PL and SIL functional safety - MACX Safety Sensor / Field CH HHT OUT active PLC / DCS AI passive CH HHT POWER POWER I I I I POWER OUT OUT 2-channel ma input, [Ex ia], powered ma output (active) PL d according to EN ISO Up to SIL 3 according to IEC Installation in zone 2 possible Plug-in screw and push-in connection technology 3-way electrical isolation, per channel Bidirectional HART communication possible Power supply via D rail connector possible HHT Zone 0,1,2 Zone 20,21, CH GND +24V active GND V 1.1 Power passive CH Zone 2 HHT 2-channel repeater power supply Ex: Housing width 12.5 mm Input data per channel Input signal 4 ma ma Transmitter supply voltage > 16 V (at 20 ma) Underload/overload signal range 0 ma ma Output data per channel Output signal 4 ma ma (active) Load 450 Ω (20 ma) Underload/overload signal range 0 ma ma General data Supply voltage range 19.2 V DC V DC (24 V DC (-20% %)) Current consumption < 100 ma (24 V/20 ma) Power dissipation < 1.4 W (at 24 V DC/20 ma) Temperature coefficient < 0.01%/K Step response (10-90%) < 1.3 ms (for 4 ma ma step) Transmission error, typical < 0.05% (of final value) Maximum transmission error < 0.1% (of final value) Electrical isolation Input/output, power supply 300 V rms (rated insulation voltage (surge voltage category II; pollution degree 2, safe isolation as per EN )) 2.5 kv (50 Hz, 1 min., test voltage) Input/output 375 V (peak value in accordance with EN ) Input/power supply 375 V (peak value in accordance with EN ) Output 1/output 2/ power supply 1.5 kv (50 Hz, 1 min., test voltage) Ambient temperature range -20 C C (any mounting position) Status indication Green LED (supply voltage) SMART communication Yes Signal bandwidth as per HART specifications Protocols supported HART Housing material PA 66-FR Dimensions W/H/D 12.5/99/114.5 mm Screw connection solid/stranded/awg mm²/ mm²/24-14 Spring-cage connection (solid/stranded/awg) mm²/ mm²/24-16 EMC note Class A product, see page 443 Safety data as per ATEX Max. output voltage U o 25.2 V Max. output current I o 93 ma Max. output power P o 587 mw Maximum voltage U m 253 V AC (125 V DC) Conformance / approvals Conformance CE-compliant, additionally EN ATEX IECEx SIL in accordance with IEC Performance level according to ISO PLd II (1) G [Ex ia Ga] IIC/IIB II (1) D [Ex ia Da] IIIC II 3(1) G Ex na [ia Ga] IIC T4 Gc [Ex ia Ga] IIC/IIB, [Ex ia Da] IIIC, Ex na [ia Ga] IIC T4 Gc Description Type Order No. Repeater power supply, two-channel, with performance level, intrinsically safe input Screw connection MACX PL-EX-RPSS-2I-2I Spring-cage connection MACX PL-EX-RPSS-2I-2I-SP For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 345

25 Measurement and control technology - signal conditioners with PL and SIL functional safety - MACX Safety Temperature Temperature transducer, Ex i Sensor /Field OUT PLC /DCS POWER I OUT TC - + Poti ϑ RTD ϑ ϑ Power 24V...230V AC/DC GND 3.3 I OUT NC passive DI Universal, with limit value relays, wide range power supply Zone 0,1,2 Zone 20,21,22 Zone DI Input for resistance thermometers, thermocouples, resistance-type sensors, potentiometers, mv sources, [Ex ia] Differential measurement possible with Pt 100 A safety-related limit value relay, by bridging two relays An additional limit value relay for non-safety-related function PL d according to EN ISO Up to SIL 2 according to EN Configuration via software (ANALOG-CONF or FDT/DTM) Cold junction compensation with separate plug Wide range power supply V AC/DC Status indicators for supply voltage, cable, sensor, and module errors Installation in zone 2 possible Plug-in screw and push-in connection technology Input data Resistance thermometers Thermocouple sensors Resistor Potentiometer Voltage Output data Output signal Maximum output signal Load R B Behavior in the event of a sensor error Switching output Contact type Contact material Max. switching voltage Max. switching current General data Supply voltage range Power consumption Temperature coefficient Maximum transmission error Electrical isolation Housing width 35 mm Pt, Ni, Cu sensors: 2, 3, 4-wire B, E, J, K, N, R, S, T, L, U, CA, DA, A1G, A2G, A3G, MG, LG 0 Ω kω 0 Ω kω mv mv 4 ma ma 22 ma 600 Ω (20 ma) According to NE 43 or freely configurable Relay output 2 PDT AgSnO 2, hard gold-plated 250 V AC (250 V DC) 2 A (250 V AC)/2 A (28 V DC) 24 V V AC/DC (-20%/+10%, 50/60 Hz) < 2.4 W 0.01%/K 0.1% (e.g. for Pt 100, 300 K span, ma) Input/output/power supply 2.5 kv (50 Hz, 1 min., test voltage) Input/output 375 V (peak value in accordance with EN ) Input/power supply 375 V (peak value in accordance with EN ) Input/switching output 375 V (peak value in accordance with EN ) Output/supply 300 V rms (rated insulation voltage (surge voltage category II; pollution degree 2, safe isolation as per EN )) Ambient temperature range -20 C C Humidity Typ. 5%... 95% (non-condensing) Housing material PA 66-FR Inflammability class in acc. with UL 94 V0 Dimensions W/H/D 35/99/114.5 mm Screw connection solid/stranded/awg mm²/ mm²/24-14 Spring-cage connection (solid/stranded/awg) mm²/ mm²/24-16 EMC note Class A product, see page 443 Safety data as per ATEX Max. output voltage U o 6 V Max. output current I o 7.4 ma Max. output power P o 11 mw Conformance / approvals Conformance CE-compliant ATEX II (1) G [Ex ia Ga] IIC II (1) D [Ex ia Da] IIIC II 3 G Ex na nc ic IIC T4 Gc X IECEx [Ex ia Ga] IIC, [Ex ia Da] IIIC, Ex na nc ic IIC T4 Gc X SIL in accordance with IEC Performance level according to ISO PLd 346 PHOENIX CONTACT Description Type Order No. Temperature transducer with threshold value switch, with performance level, intrinsically safe input Screw connection MACX PL-EX-T-UIREL-UP Spring-cage connection MACX PL-EX-T-UIREL-UP-SP Accessories Programming adapter for configuring modules with S-PORT interface Plug with 50 Ω resistor, for current signals between +20 ma and -20 ma IFS-USB-PROG-ADAPTER MACX MCR-EX-I

26 Configuration software ANALOG-CONF and FDT/DTM Interface technology and switching devices Measurement and control technology - signal conditioners with PL and SIL functional safety - MACX Safety Input configuration with indication of the pin assignment Relay configuration ANALOG-CONF The user-friendly ANALOG-CONF software allows you to quickly and clearly configure the temperature modules. The pin assignment for the input and output is directly displayed. You have access to the complete range of configurable parameters. You have the option to pre-configure parameters and then import them into any number of temperature transducers or read the data from the device and directly display the settings and measured values. FDT/DTM Configuration is also possible via the FDT/DTM universal configuration tool. The DTM files can simply be downloaded in the download area for the item. The following parameters can be configured: Restart following failsafe Input: Resistance thermometer Thermocouples Potentiometer Remote resistance-type sensor Voltage signals ±1 V User characteristic curve Additional analog signals Filter Cold junction Analog output: Type of fault signaling Switching outputs: Acknowledgement, switching behavior Switch-on/off delay Monitoring: Representation in diagram or value list, recording possible Service: Reset, password protection, display DIP switch position and much more Monitoring function Configuration with FDT/DTM For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 347

27 Monitoring, energy, and power measuring technology Software for acquisition of usage data The EMwise software from Phoenix Contact is the efficient solution for acquiring energy data regarding heat, cold, air or electricity in conjunction with a small-scale controller. Integrate up to 24 digital inputs, 8 analog channels, 50 EMpro energy meters, 30 M-bus counters, and 4 IO-Link measuring sensors. A web-based interface is available for system parameterization. Each device/channel can be configured individually, without any programming knowledge. The configuration is saved to a file and can be reused for identical systems. Your advantages: Startup without programming knowledge Direct parameterization of predefined sensors Three software versions, suitable for every application: EMWISE IMPULS: for up to 16 digital signals EMWISE IMP ANALOG: for up to 16 digital and 6 analog signals EMWISE EXTENDED: for up to 24 digital and 8 analog signals, EMpro energy meters, M-bus counters, M-bus level converters, IO-Link sensors See phoenixcontact.net/products Description Type Order No. Program and configuration memory, plug-in, 2 GB with license key and application program for reading from measuring devices via pulses Program and configuration memory, plug-in, 2 GB with license key and application program for reading from measuring devices via pulses and analog values Program and configuration memory, plug-in, 2 GB with license key and application program for reading from measuring devices via pulses, analog values, M-bus, Modbus RTU, and IO-Link SD FLASH 2GB EMWISE IMPULS SD FLASH 2GB EMWISE IMP ANALOG SD FLASH 2GB EMWISE EXTENDED PHOENIX CONTACT

28 Software for data logging Interface technology and switching devices Monitoring, energy, and power measuring technology Turn your controller into a data logger. The SD FLASH 512MB ILDLC FLEX memory card from Phoenix Contact provides all the software needed to extend your PLC for use as a data logger. The software contains the familiar application from the FLEX data logger kit. In conjunction with the ILC 151 GSM/GPRS small-scale controller, 3 digital and 4 analog input or output terminal blocks can be mounted. The mounted terminals are automatically detected and started up by the controller. Different PCP channels can also be selected during parameterization. Your advantages: Send digital and analog status information via SMS or or write it to an SQL database Startup without programming knowledge See phoenixcontact.net/products Description Type Order No. SD FLASH card with data logger FLEX application SD FLASH 512MB ILDLC FLEX For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 349

29 Monitoring, energy, and power measuring technology Sensors and meters Pressure sensor with IO-Link Pressure sensors from Phoenix Contact detect the operating pressure of gas media in a range from -1 to 10 bar. The overloadproof ceramic measuring cell is designed for in excess of 100 million cycles and enables a high switching point accuracy. The pressure switch offers the option of using the set switching points via two switching outputs or reading all process data via the IO-Link interface. Your advantages: IO-Link communication Parameterization, diagnostics, and process value monitoring via IO-Link Programmable function 4-character alphanumeric display Pressure monitoring Measuring range -1 bar bar (minimum burst pressure 150 bar) Pressure resistance 75 bar Process connection G1/4 I Supply for module electronics Connection method M12 connector No. of pos. 4 Supply voltage range 18 V DC V DC Current draw < 35 ma Digital outputs Number of outputs 2 (OUT1 = switching output, OUT2 = switching output or diagnostic output) Connection method M12 connectors, assigned four times Delay time 0.3 s (operational readiness) IO-Link Specification V1.1 Transmission speed (38.4 kbaud) General data Weight 263 g Width 34 mm Height 91.5 mm Depth 48 mm Degree of protection IP65 Protection class III Ambient temperature (operation) -25 C C Ambient temperature (storage/transport) -40 C C Vibration resistance in acc. with EN /IEC g (10 Hz Hz) Description Type Order No. Pressure switch with indicator, G1/4 I process connection, IO-Link communication PSK APS7004IOL PHOENIX CONTACT

30 Monitoring, energy, and power measuring technology For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 351

31 Monitoring, current, and voltage measuring technology Current transformers for retrofitting PACT RCP Fast installation without removing system parts Fast installation in a confined space PACT current transformers for retrofitting can be conveniently mounted where there is not enough space for split core current transformers. System downtimes are reduced as system parts do not have to be removed for installation. Simply place the handy Rogowski coil quickly around power rails and circular conductors. The measuring transducer connected downstream supplies the same typical secondary currents as a standard current transformer. Your advantages: High system availability due to reduced downtimes: fast installation without removing system parts Transform alternating currents up to 4000 A using a single measuring system Space saving and handy, as the current strength does not affect the size and weight of the coil Safe installation and operation: no dangerous open circuit voltages Harmonics and transients detected with phase accuracy with a large frequency spectrum from 10 to 5000 Hz Rogowski coil secured on power rails and circular conductors thanks to professional holding device Eight different current measuring ranges from 100 to 4000 A Detect harmonics and transients with a large frequency spectrum from 10 to 5000 Hz Professional holding device for power rails 352 PHOENIX CONTACT

32 Current transformers for retrofitting PACT RCP Interface technology and switching devices Monitoring, current, and voltage measuring technology Practical handling due to the flexible measuring coil for opening Universal application possibilities through 8 different current measuring ranges in one device: ( /... /... /4,000 A) The large bandwidth ( ,000 Hz) enables harmonics and transients to be detected It is not possible for dangerous open circuit voltages to occur The bracket ensures optimum alignment of the measuring coil to the power rail Low space requirement in the control cabinet Measuring coil input data Frequency range Input signal Position error Current transformer for subsequent installation in the field 10 Hz Hz Sine < 1% (the measuring coil is at right angles to the live connector.) Recommendations for the use of coil lengths and power rail dimensions Power rail Diameter/ coil length 1 power rail per phase 2 power rails 3 power rails per phase per phase [mm x mm] [mm] 30 x 10 95/300 X X 40 x 10 95/300 X X 40 x /450 X 50 x 10 95/300 X 50 x /450 X X 60 x 10 95/300 X 60 x /450 X X 60 x /450 X X X 100 x /450 X X 100 x /600 X 120 x /450 X 120 x /600 X X 160 x /600 X X X Measuring coil signal output Output signal (at 50 Hz) 100 mv (no load, at 1,000 A) General data, measuring coil Length of signal cable 3000 mm Rated insulation voltage 1000 V AC (rms CAT III) 600 V AC (rms CAT IV) Test voltage kv (DC/1 min.) Ambient temperature (operation) -30 C C (measuring coil) Ambient temperature (storage/transport) -40 C C (measuring coil) Measuring transducer input data Measuring ranges (current) via DIP switch 100 A 250 A 400 A 630 A 1000 A 1500 A 2000 A 4000 A Phase angle < 1 Measuring transducer signal input Input signal (at 50 Hz) 100 mv (1000 A) Measuring transducer signal output Current output signal 1 A AC (effective at sine) Miscellaneous data for measuring transducer Nominal supply voltage 24 V DC -20 % % Nominal supply voltage range 19.2 V DC V DC Transmission error, maximum 0.5% (from the range end value) Linearity error < 0.5% (from the range end value) Frequency range 45 Hz Hz Degree of protection IP20 Test voltage 1.5 kv AC (supply/input and output) Dimensions W/H/D 22.5/70.4/85 mm Ambient temperature (operation) -20 C C (measuring transducer) Ambient temperature (storage/transport) -25 C C (measuring transducer) General data for the set Altitude < 2000 m Permissible humidity (operation) 5%... 95% (non-condensing) Approvals / conformities Standards/specifications IEC IEC IEC IEC Description Type Order No. Current transformer for retrofitting, set consisting of Rogowski coil and measuring transducer, output signal: 1 A AC (effective for sine) Length of measuring coil 300 mm PACT RCP-4000A-1A-D Length of measuring coil 450 mm PACT RCP-4000A-1A-D Length of measuring coil 600 mm PACT RCP-4000A-1A-D Accessories Holding device for power rail PACT RCP-CLAMP For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 353

33 Relay modules - PLC logic programmable logic relay system Extremely compact control The PLC logic programmable logic relay system is the extremely compact way to carry out small automation tasks easily and flexibly. It consists of the PLC-V8C logic modules, the PLC-TERFACE relay system, and the LOGIC+ software. The logic modules are simply plugged into a row of eight PLC-TERFACE terminal blocks and combine the logic and interface level in one unit. Depending on the switching requirements, plug-in electromechanical and solid-state relays can be combined in order to flexibly switch and control the I/O signals. PLC logic processes digital and analog input signals as well as logic functions and timer modules - and replaces conventional switching and control devices. Up to 16 I/O signals can be processed using the standalone logic modules - that's with a design width of just 50 mm. If more I/O signals are required, a maximum of 48 I/O signals can be linked using the basic and extension modules. Switching and controlling with plug-in relays PLC logic brings together the standard combination of logic module and separate plug-in relay and eliminates the wiring effort and additional switching elements Convenient connections with screw or push-in connection technology, which also accommodate return conductors, remove the need for separate potential terminal blocks Each relay channel can be freely configured as an input or output. PLC logic therefore perfectly adapts to fit the application at hand Intuitive programming Programming is quick and easy with the intuitive LOGIC+ programming software. Ladder (LD) and function block diagrams (FBD) can be created by selecting the relevant functions and their connection using drag & drop. The graphical representation of PLC logic in the hardware editor supports intuitive operation. The programs created can be simulated offline on the PC and tested online during operation. Basic functions, such as AND, OR, NOT, etc. are complemented by special functions, such as counters, seven-day timers, timer modules, and mathematical functions, to name a few. 354 PHOENIX CONTACT

34 Relay modules - PLC logic programmable logic relay system Logic module with plug-in relays PLC logic combines a logic module and plug-in relay and eliminates the wiring effort and additional switching elements. Each relay channel can be flexibly equipped with an electromechanical or a solid-state relay. PLC logic processes 16 I/O signals with just one logic module and boasts an extremely compact design width of just 50 mm. Intuitive programming with LOGIC+ Function block diagram or ladder diagram Numerous integrated function blocks Specific function blocks are available to download Hardware view in the program Download free of charge at Standard programming cable PLC logic is connected to a PC via a standard micro USB cable. The drivers for PLC logic are automatically installed on connection by means of plug and play. Easily connect extension modules The basic module and the extension module are connected via integrated connectors - no tools required. A maximum of two extension modules can be connected to a basic module. This means that PLC logic can work with up to 48 I/Os. Saving and copying data PLC logic programs are saved by the memory block or can be easily copied to other devices. If settings such as time or date are required on the new device, these values can be configured via the integrated web server. The new device does not need access to the LOGIC+ software for this. Integration into PROFIBUS DP Adaptable fieldbus gateways, available as an option, can be used to integrate PLC logic into a PROFIBUS DP network. This enables communication with a higherlevel controller for remote control, diagnostics, and visualization purposes. DTM device drivers and GSD files for configuring the gateway can be downloaded free of charge at For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 355

35 A1 Interface technology and switching devices Relay modules - PLC logic programmable logic relay system Logic modules PLC-V8C are the plug-in logic modules which form the PLC logic relay system in conjunction with the narrow 6.2 mm PLC-TERFACE terminal blocks. Eight freely selectable PLC-TERFACE terminal blocks must be separately ordered for each logic module. You can find an overview of matching PLC-TERFACE terminal blocks on page 360. All logic modules feature these properties: 8 integrated digital inputs (of which two inputs are configurable as analog inputs), connection via connector with screw or push-in connection technology A further 8 channels can be configured with matching PLC-TERFACE terminal blocks as digital inputs or outputs Programming with the LOGIC+ software 24 V 0 V IO 8 Stand-alone module 24 V 0 V IO 9 IO 10 PLC-V8C/.../SAM IO 11 IO 12 IO 13 IO 14 IO 15 PLC-V8C.../SAM Stand-alone logic module with 16 I/Os, not extendable Connection to PC via micro USB socket Integrated realtime clock (RTC) Accommodates external IFS-CONFSTICK memory block PLC-V8C.../BM Basic logic module with 16 I/Os, can be extended with a maximum of two extension modules (PLC-V8C.../EM) to 48 I/Os Connection to PC via micro USB socket Integrated realtime clock (RTC) Accommodates external IFS-CONFSTICK memory block Optional connection to PROFIBUS-GATEWAY-IFS PLC-V8C.../EM Extension logic module with 16 I/Os, for extending the basic module 24 V 0 V A2 A1 A2 A1 A2 A1 A2 13 BB BB Supply Supply voltage 24 V DC Supply voltage range 19.2 V DC V DC Max. input current at U N 120 ma Input data (digital) Number of inputs 8 (2 configurable as analog) Input voltage 24 V DC Description of the input EN , type 3 Input current 0-signal < 1 ma Input current 1-signal Typ. 2.5 ma Input data (analog) Number of inputs 2 (6 and 7 are configurable as analog) Input voltage range 0 V V Input resistance > 4 kω Input data (PLC-TERFACE) Number of inputs 8 Output data (for controlling PLC-TERFACE) Number of outputs 8 Nominal voltage 24 V DC Nominal current 9 ma Realtime clock (basic module only) Buffer time (capacitor) 24 h (capacitor) Realtime clock accuracy ±2 s/d General data Ambient temperature (operation) -20 C C Ambient temperature (storage/transport) -20 C C Permissible humidity (operation) 90% Air and creepage distances between the power circuits D EN BB BB 14 Rated insulation voltage 50 V Rated surge voltage 0.8 kv Insulation Basic insulation Mounting type Can be plugged onto 8 x PLC-TERFACE Degree of protection IP20 Screw connection solid/stranded/awg mm²/ mm²/28-16 Push-in connection solid/stranded/awg mm²/ mm²/26-16 Description Type Order No. PLC-V8C plug-in logic modules With screw connection PLC-V8C/SC-24DC/SAM With push-in connection PLC-V8C/PT-24DC/SAM PHOENIX CONTACT

36 A1 Interface technology and switching devices Relay modules - PLC logic programmable logic relay system Basic module Extension module 24 V 0 V 24 V 0 V IO 8 24 V 0 V A2 A1 IO 9 A2 A1 IO 10 PLC-V8C/.../BM A2 A1 IO 11 IO 12 IO 13 A2 13 BB BB IO 14 BB IO 15 BB 14 Contacting for Extension module Contacting for Basic or Extension module A1 IO 8 24 V 0 V A2 A1 IO 9 A2 A1 IO 10 PLC-V8C/.../EM A2 A1 IO 11 IO 12 IO 13 A2 13 BB BB IO 14 BB IO 15 BB 14 Contacting for Extension module 24 V 0 V 24 V 0 V 24 V DC 24 V DC 19.2 V DC V DC 19.2 V DC V DC 120 ma 65 ma 8 (2 configurable as analog) 8 (2 configurable as analog) 24 V DC 24 V DC EN , type 3 EN , type 3 < 1 ma < 1 ma Typ. 2.5 ma Typ. 2.5 ma 2 (6 and 7 are configurable as analog) 2 (6 and 7 are configurable as analog) 0 V V 0 V V > 4 kω > 4 kω V DC 24 V DC 9 ma 9 ma 24 h (capacitor) - ±2 s/d C C -20 C C -20 C C -20 C C 90% 90% D EN D EN V 50 V 0.8 kv 0.8 kv Basic insulation Basic insulation Can be plugged onto 8 x PLC-TERFACE Can be plugged onto 8 x PLC-TERFACE IP20 IP mm²/ mm²/ mm²/ mm²/ mm²/ mm²/ mm²/ mm²/26-16 Type Order No. Type Order No. PLC-V8C/SC-24DC/BM PLC-V8C/SC-24DC/EM PLC-V8C/PT-24DC/BM PLC-V8C/PT-24DC/EM For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 357

37 Relay modules - PLC logic programmable logic relay system Accessories Programming cable and memory block The programming cable (MICRO USB B to USB A) is used to connect PLC logic to a PC, length: 2 m PLC logic programs are saved by the memory block or can be easily copied to other devices General data EMC note Class A product, see page 443 Description Color Type Order No. Type Order No. Programming cable Multi-functional memory block for the TERFACE system CAB-USB A/MICRO USB B/2,0M Flat design IFS-CONFSTICK Accessories Gateway to PROFIBUS DP The gateways are connected to the PLC-V8C.../BM PLC logic basic modules via the ME 22,5 TBUS... D rail connector and the PLC-V8C/CAB... connecting cable. The gateways are connected to a PC and configured via the integrated S-PORT interface and the IFS-USB-DATACABLE. D H W General data EMC note Class A product, see page 443 Description Color Type Order No. Type Order No. IFS gateway for PROFIBUS DP green EM-PB-GATEWAY-IFS Programming adapter for configuring modules with S-PORT interface Cable length: 3 m IFS-USB-DATACABLE D rail connector green ME 22,5 TBUS 1,5/ 5-ST-3,81 GN Connecting cable for connecting PLC logic with the ME 22,5 TBUS D rail connector, cable length: 0.3 m PLC-V8C/CAB/TBUS/0,3M PHOENIX CONTACT

38 Accessories PLC logic starter kit The PLC logic starter kit contains all the components needed to get started quickly and easily with PLC logic with push-in connection technology and 8 inputs and 8 outputs. PLC-V8C-PT/24DC/BM plug-in logic module PLC-RPT-24DC/1/ACT eight relay output terminal blocks Micro USB programming cable Software LOGIC+ PLC logic quick start guide poster Interface technology and switching devices Relay modules - PLC logic programmable logic relay system Description Color Type Order No. PLC logic starter kit 1, 8 integrated inputs (24 V DC) and 8 outputs via PLC-TERFACE (switching capacity 250 V AC/DC, max. 6 A) PLC-LOGIC-STARTERKIT Dimensional drawing For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 359

39 Relay modules - PLC logic programmable logic relay system Selection table for PLC-TERFACE Push-in connection Screw connection Relay output Type Order No. Type Order No. 1 PDT, output data 6 A, 250 V AC/DC PLC-RPT-24DC/ PLC-RSC-24DC/ PDT, output data 50 ma, 36 V DC, gold contact PLC-RPT-24DC/21AU PLC-RSC-24DC/21AU N/O contact, output data 6 A, 250 V AC/DC, actuator type PLC-RPT-24DC/1/ACT PLC-RSC-24DC/1/ACT N/O contact with switch, output data 6 A, 250 V AC/DC PLC-RPT-24UC/1/S/H PLC-RSC-24UC/1/S/H Solid-state relay output Output data 100 ma, 3 V DC - 48 V DC PLC-OPT-24DC/48DC/ PLC-OSC-24DC/48DC/ Output data 3 A, 3 V DC - 33 V DC PLC-OPT-24DC/24DC/ PLC-OSC-24DC/24DC/ Output data 750 ma, 24 V AC V AC PLC-OPT-24DC/230AC/ PLC-OSC-24DC/230AC/ Output data 3 A, 3 V DC - 33 V DC, actuator type PLC-OPT-24DC/24DC/2/ACT PLC-OSC-24DC/24DC/2/ACT Output data 750 ma, 24 V AC V AC, actuator type PLC-OSC-24DC/230AC/1/ACT Output data 1 A, 12 V DC V DC PLC-OPT-24DC/300DC/ PLC-OSC-24DC/300DC/ Output data 10 A, 3 V DC - 33 V DC PLC-OPT-24DC/24 DC/10/R PLC-OSC-24DC/24DC/10/R Output data 500 ma, 3 V DC - 48 V DC, electronic PDT PLC-OPT-24DC/48DC/500/W PLC-OSC-24DC/48DC/500/W Output data, TTL, 50 ma, 5 V DC PLC-OPT-24DC/TTL PLC-OSC-24DC/TTL Relay input Input voltage 24 V DC PLC-RPT-24DC/1AU/SEN PLC-RSC-24DC/1AU/SEN Input voltage 120 V AC/DC PLC-RPT-120UC/1AU/SEN PLC-RSC-120UC/1AU/SEN Input voltage 230 V AC/DC PLC-RPT-230UC/1AU/SEN PLC-RSC-230UC/1AU/SEN Input voltage 5 V DC (basic terminal block without relay) PLC-BSC- 5DC/ 1/SEN Relay for 5 V DC basic terminal block REL-MR-4,5DC/21AU Solid-state relay input Input voltage 24 V DC PLC-OPT-24DC/48DC/100/V8C/SEN PLC-OSC-24DC/48DC/100/V8C/SEN Input voltage 120 V AC/DC PLC-OPT-120UC/48DC/100/V8C/SEN PLC-OSC-120UC/48DC/100/V8C/SEN Input voltage 230 V AC/DC PLC-OPT-230UC/48DC/100/V8C/SEN PLC-OSC-230UC/48DC/100/V8C/SEN Dummy or reserve Basic terminal block output PLC-BPT-24DC/ PLC-BSC-24DC/ Basic terminal block input PLC-BPT-24DC/1/SEN PLC-BSC-24DC/1/SEN PHOENIX CONTACT

40 Relay modules - PLC logic programmable logic relay system LOGIC+ programming software Integrated web server PLC logic basic settings are easily configured via the integrated web server. The LOGIC+ software does not need to be installed in order to do so. Time and date Password and access control Firmware update Status indicators for inputs and outputs General device information LOGIC+ user interface Clear separation in program editor, toolbox, hardware view, and signaling window All elements can be easily placed using drag & drop Notes and errors are highlighted in color in the program editor Hardware configurator Each relay channel can be configured as an input or output with an electromechanical or a solid-state relay Clear assignment of the inputs and outputs thanks to the graphical representation of the hardware connections Function blocks Basic functions: AND, OR, NOT, XOR Mathematical functions: add, divide, multiply, subtract, generate absolute value Positive and negative edge detection RS and SR flip-flops Switch-on and switch-off delay, pulse encoder, pulse stretching, weekly clock timer Up and down counter Analog and digital comparators Special functions, e.g., solar altitude calculations are available for download Simulation and online values Offline simulation: Simulation of the created program directly in LOGIC+ Virtualization of the values in the program editor, hardware view, and in the observation window Online values: Representation of the program running on the hardware in LOGIC+ with online values Overwriting of values from LOGIC+ Example programs Numerous application examples make it easy to get started with LOGIC+. These include: Underground garage ventilation Conveyor belt Pumping plant Two-way control Tips for creating shift registers or surge relays For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 361

41 Relay modules - RIFLE complete Fully mounted RIF-0 relay modules D W H Fully mounted RIF-0 relay modules, consisting of: Relay base with push-in connection Solid-state relays Relay ejector lever on the housing The advantages: Status LED integrated into the base RTIII sealed solid-state relay Zero voltage switch at AC output Professional bridging of adjacent modules saves wiring time Max. DC voltage output of 3 A A2- A1+ Load current [A] Ambient temperature [ C] Derating curve for RIF-0-OPT-24DC/24DC/2 Input data 1 Rated actuating voltage range with reference to U C Switching level (with reference to U C ) 1 signal ("H") > signal ("L") < 0.4 Rated actuating current I C [ma] 8.5 Typ. switch-on time at U N [ms] 0.02 Typ. switch-off time at U N [ms] 0.3 Transmission frequency f limit [Hz] 300 Input circuit DC Yellow LED, free-wheeling diode Output data Max. switching voltage 33 V DC Min. switching voltage 3 V DC Max. inrush current 15 A (10 ms) Min./max. switching current -/3 A (see derating curve) Output protection Protection against polarity reversal, surge protection Voltage drop at max. limiting continuous current < 200 mv Leakage current in off state - Phase angle (cos φ) - Max. load value - General data Test voltage input/output 2.5 kv rms (50 Hz, 1 min.) Ambient temperature (operation) -25 C C Standards/regulations D EN Pollution degree/surge voltage category 2/III Connection data solid/stranded/awg mm²/ mm²/26-16 Dimensions W / H / D 6.2 mm/93 mm/66 mm EMC note Class A product, see page 443 Description Rated actuating voltage U C Type Order No. Coupling relay modules with solid-state relay and push-in connection 1 24 V DC RIF-0-OPT-24DC/24DC/ Load current [A] 0,8 0,7 0,6 0,5 0,4 0,3 0,2 0, Ambient temperature [ C] Derating curve for RIF-0-OPT-24DC/230AC/1 362 PHOENIX CONTACT

42 Relay modules - RIFLE complete D W H D W H Max. DC voltage output of 100 ma Max. AC voltage output of 750 ma A2- A1+ A2- A > 0.8 > 0.8 < 0.4 < Yellow LED, free-wheeling diode Yellow LED, free-wheeling diode 48 V DC 253 V AC 3 V DC 24 V AC - 30 A (10 ms) -/100 ma 10 ma/0.75 A (see derating curve) Protection against polarity reversal, surge protection RCV circuit < 1 V < 1 V - 1 ma (in off state) A 2 s (tp = 10 ms, at 25 C) 2.5 kv rms (50 Hz, 1 min.) 2.5 kv rms (50 Hz, 1 min.) -25 C C -25 C C D EN D EN /III 2/III mm²/ mm²/ mm²/ mm²/ mm/93 mm/66 mm 6.2 mm/93 mm/66 mm Class A product, see page 443 Class A product, see page 443 Type Order No. Type Order No. RIF-0-OPT-24DC/48DC/ RIF-0-OPT-24DC/230AC/ For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 363

43 Relay modules - RIFLE complete Fully mounted RIF-1 relay modules D W H Fully mounted RIF-1 relay modules, consisting of: Relay base with push-in connection 1 or 2 PDT relays with detectable manual operation Relay retaining bracket Input module/interference suppr. module (AC types only) The advantages: Relay with lockable manual operation and status LED With DC types, free-wheeling diode is integrated into relay Mechanical switch position indicator Professional bridging of adjacent modules saves wiring time RIF-1 relay module with 1 PDT relay A2- A1+ DC coils A2 AC coils A1 Input data 1 2 Permissible range (with reference to U N ) see diagram Typ. input current at U N [ma] Typ. response time at U N [ms] Typ. release time at U N [ms] Input circuit AC Yellow LED, varistor Input circuit DC Yellow LED, damping diode Output data Contact type 1 PDT Contact material AgNi Max. switching voltage 250 V AC/DC Min. switching voltage 12 V (at 10 ma) Limiting continuous current (see diagram) Max. inrush current 32 A (20 ms, N/O contact) Min. switching current 10 ma (at 12 V) General data Test voltage (winding / contact) 4 kv rms (50 Hz, 1 min.) Ambient temperature (operation), AC -40 C C Ambient temperature (operation), DC -40 C C Nominal operating mode 100% operating factor Mechanical service life Approx. 5 x 10 6 cycles Standards/regulations D EN 50178, IEC Pollution degree/surge voltage category 2/III Mounting position/mounting Any/in rows with zero spacing Connection data solid/stranded/awg mm²/ mm²/26-16 Dimensions W / H / D 16 mm/93 mm/75 mm EMC note Class A product, see page 443 Description Input voltage U N Type Order No. Coupling relay modules with power contact relay with manual operation and push-in connection 1 24 V DC RIF-1-RPT-LDP-24DC/1X21MS V AC RIF-1-RPT-LV-230AC/1X21MS PHOENIX CONTACT

44 Relay modules - RIFLE complete D W H RIF-1-RPT.../1X21... (1 PDT) Operating voltage range Interrupting rating RIF-1 relay module with 2 PDT relay Coil voltage U/U N 1,8 1,7 1,6 1,5 1,4 1,3 1,2 1,1 1,0 0,9 0,8 0,7 0, Ambient temperature [ C] DC coils AC coils Switching current [A] ,5 0,2 0, = AC, ohmic load = DC, ohmic load Switching voltage [V] Contact derating Electrical service life A A see diagram Yellow LED, varistor Yellow LED, damping diode 2 PDT AgNi 250 V AC/DC 12 V (at 10 ma) (see diagram) 16 A (20 ms, N/O contact) 10 ma (at 12 V) 4 kv rms (50 Hz, 1 min.) -40 C C -40 C C 100% operating factor Approx. 5 x 10 6 cycles D EN 50178, IEC /III Any/in rows with zero spacing mm²/ mm²/ mm/93 mm/75 mm Class A product, see page 443 Type DC coils A2 21 AC coils Order No. 11 A1 RIF-1-RPT-LDP-24DC/2X21MS RIF-1-RPT-LV-230AC/2X21MS Limiting continuous current per contact [A] DC coil Ambient temperature [ C] AC coil DC coil, jumper between 11 and 21 AC coil, jumper between 11 and 21 RIF-1-RPT.../2X21... (2 PDTs) Operating voltage range Coil voltage U/U N 1,8 1,7 1,6 1,5 1,4 1,3 1,2 1,1 1,0 0,9 0,8 0,7 0, Ambient temperature [ C] DC coils AC coils Contact derating Limiting continuous current per contact [A] Ambient temperature [ C] DC coil AC coil Cycles ,5 0,2 0, = 250 V AC, ohmic load Interrupting rating Switching current [A] 1 Switching current [A] Switching voltage [V] AC, ohmic load DC, ohmic load, contacts in series DC, ohmic load Electrical service life Cycles Switching current [A] V AC, ohmic load For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 365

45 Relay modules - PLC series PLC RELAY with an integrated solid-state relay D W H 6.2 mm narrow solid-state relay for switching AC loads Status display Protection circuits in input and output Wear-free Switching capacity up to 230 V AC/2.4 A Screw and push-in connection technology Solid-state power relay with AC voltage output of 2.4 A, max. A1+ 14 BB 13+ A2- A2-13+ Load current [A] 2,5 2 1,5 1 0, Ambient temperature [ C] = aligned with > 20 mm spacing = aligned without spacing Load current as a function of the ambient temperature Operating time: 100% operating factor 366 PHOENIX CONTACT Input data 1 Rated actuating voltage range with reference to U C Switching level (with reference to U C ) 1 signal ("H") > signal ("L") < 0.4 Rated actuating current I C [ma] 8 Typ. switch-on time at U N [ms] 10 Typ. switch-off time at U N [ms] 10 Transmission frequency f limit [Hz] 10 Input circuit DC Yellow LED, protection against polarity reversal, surge protection Output data Max. switching voltage 253 V AC Min. switching voltage 24 V AC Max. inrush current 250 A (20 ms) Min./max. switching current 10 ma/2.4 A (see derating) Output protection RCV circuit Voltage drop at max. limiting continuous current < 1 V Leakage current in off state < 1 ma Phase angle (cos φ) - Max. load value 340 A 2 s (tp = 10 ms, at 25 C) General data Rated insulation voltage 260 V AC Rated surge voltage 4 kv Insulation Basic insulation Ambient temperature (operation) -25 C C Standards/regulations D EN Pollution degree/surge voltage category 2/III Connection data solid/stranded/awg mm²/ mm²/26-14 Dimensions W / H / D 6.2 mm/80 mm/86 mm EMC note Class A product, see page 443 Description Rated actuating voltage U C Type Order No. PLC TERFACE, with screw connection 1 24 V DC PLC-OSC- 24DC/230AC/2.4/ACT PLC-TERFACE, with push-in connection 1 24 V DC PLC-OPT- 24DC/230AC/2.4/ACT

46 Relay modules - PLC series For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 367

47 System cabling for controllers - VARIOFACE system cabling VIP - power cabling Universal front adapters for SIMATIC S7-300 Four connection options are available: Connection of 40-pos. modules via four cables, each with a 10-pos. COMBI connector Connection of 20-pos. modules via two cables, each with a 10-pos. COMBI connector Connection of 40-pos. modules via 40 individual wires in rope structure (not assembled) Connection of 20-pos. modules via 20 individual wires in rope structure (not assembled) The front adapters have the following features: Can be screwed on/snapped in with the I/O module Suitable for all common S7-300 modules, up to max. 250 V AC/DC, 6 A Universal 1:1 connection Numerically marked wires/connectors Combination example: A front adapter with punched-on 10-pos. COMBI connectors can be combined with the following modular terminal blocks for field connection: UT 2,5/1P PT 2,5/1P ST 2,5/1P ST 2,5-TW-MT/1P You can find further versions, accessories, and combination options in Catalog 3 Modular terminal blocks in the Plug-in COMBI connection solutions section, or online at phoenixcontact.net/products. A...4X10COMBI X10COMBI X10 PT X10 PT... A B B COMBI S7-300 S COMBI Max. perm. operating voltage 250 V AC/DC Max. perm. current carrying capacity per path 6 A (per single wire at 40 C) 4 A (per single wire at 60 C) Max. perm. total current 20 A (per cable at 40 C) 16 A (per cable at 60 C) Rated surge voltage 4 kv Insulation Basic insulation Max. conductor resistance 39 Ω/km Conductor cross section AWG 21/0.5 mm² Conductor structure: stranded wires / material 16/Cu uninsulated Outside diameter 9 mm Ambient temperature range -20 C C Standards/regulations D EN 50178, Connection method Front adapter Can be plugged onto 40-pin I/O modules System cable COMBICON connectors SP-H 2,5/10 Description Cable length Type Order No. VIP - power adapter, for universal connection of the SIMATIC S7-300 Front adapter with punched-on connectors for 40 plug-in modular terminal blocks 0.5 m VIP-PA-PWR/4X10COMBI/ 0,5M/S m VIP-PA-PWR/4X10COMBI/ 1,0M/S m VIP-PA-PWR/4X10COMBI/ 1,5M/S m VIP-PA-PWR/4X10COMBI/ 2,0M/S m VIP-PA-PWR/4X10COMBI/ 2,5M/S m VIP-PA-PWR/4X10COMBI/ 3,0M/S m VIP-PA-PWR/4X10COMBI/ 4,0M/S m VIP-PA-PWR/4X10COMBI/ 5,0M/S m VIP-PA-PWR/4X10COMBI/ 6,0M/S m VIP-PA-PWR/4X10COMBI/ 8,0M/S m VIP-PA-PWR/4X10COMBI/10,0M/S PHOENIX CONTACT

48 System cabling for controllers - VARIOFACE system cabling Front adapter with punched-on connectors for 20 plug-in modular terminal blocks Front adapter with 40 open cable ends Front adapter with 20 open cable ends S COMBI S S V AC/DC 250 V AC/DC 250 V AC/DC 6 A (per single wire at 40 C) 4 A (per single wire at 60 C) 6 A (per single wire at 40 C) 4 A (per single wire at 60 C) 6 A (per single wire at 40 C) 4 A (per single wire at 60 C) 20 A (per cable at 40 C) 16 A (per cable at 60 C) 20 A (per cable at 40 C) 16 A (per cable at 60 C) 20 A (per cable at 40 C) 16 A (per cable at 60 C) 4 kv 2.3 kv 2.3 kv Basic insulation Basic insulation Basic insulation 39 Ω/km 39 Ω/km 39 Ω/km AWG 21/0.5 mm² AWG 21/0.5 mm² AWG 21/0.5 mm² 16/Cu uninsulated 16/Cu uninsulated 16/Cu uninsulated 9 mm 13 mm 9 mm -20 C C -20 C C -20 C C D EN 50178, D EN 50178, D EN 50178, Can be plugged onto 20-pin I/O modules Can be plugged onto 40-pin I/O modules Can be plugged onto 20-pin I/O modules COMBICON connectors SP-H 2,5/10 Open cable end Open cable end Type Order No. Type Order No. Type Order No. VIP-PA-PWR/2X10COMBI/ 0,5M/S VIP-PA-PWR/2X10COMBI/ 1,0M/S VIP-PA-PWR/40XOE/ 1,0M/S VIP-PA-PWR/20XOE/ 1,0M/S VIP-PA-PWR/2X10COMBI/ 1,5M/S VIP-PA-PWR/2X10COMBI/ 2,0M/S VIP-PA-PWR/40XOE/ 2,0M/S VIP-PA-PWR/20XOE/ 2,0M/S VIP-PA-PWR/2X10COMBI/ 2,5M/S VIP-PA-PWR/2X10COMBI/ 3,0M/S VIP-PA-PWR/40XOE/ 3,0M/S VIP-PA-PWR/20XOE/ 3,0M/S VIP-PA-PWR/2X10COMBI/ 4,0M/S VIP-PA-PWR/40XOE/ 4,0M/S VIP-PA-PWR/20XOE/ 4,0M/S VIP-PA-PWR/2X10COMBI/ 5,0M/S VIP-PA-PWR/2X10COMBI/ 6,0M/S VIP-PA-PWR/40XOE/ 6,0M/S VIP-PA-PWR/20XOE/ 6,0M/S VIP-PA-PWR/2X10COMBI/ 8,0M/S VIP-PA-PWR/40XOE/ 8,0M/S VIP-PA-PWR/20XOE/ 8,0M/S VIP-PA-PWR/2X10COMBI/10,0M/S VIP-PA-PWR/40XOE/10,0M/S VIP-PA-PWR/20XOE/10,0M/S For additional information, visit phoenixcontact.net/products PHOENIX CONTACT 369