SplashETech Mini0805 Instruction Manual Please read this manual carefully before using this product. Please get this manual well-kept for future reference. Please use the product correctly based on a full understanding of the manual.
List of Parts Before using this product, please make sure that your dashboard camera package consists of all the following items. Please contact the distributor in case of any loss. Name of Items SplashETech Mini0805 Car Charger USB Cable 3M Plastic Sticker Vehicle Mounting Bracket (GPS Tracker) Instruction Manual Quantity Precautions There may be a layer of plastic protective film on the LCD screen and the lens, which is intended to prevent any scratch during transportation. In that case, please remove the protective film before putting the product into use. The product will generate heat after being used for a long time. Please note that it is not a malfunction. Do not try to disassemble, refit or heat the product. Doing so may result in electrical shock and will most likely resulting in damaging the dash camera. Please keep the product from water or any other liquid. Do not clean the product using alcohol, gasoline, diluent or any other organic solvent. Only a dry cloth should be used. Do not mistreat the dash camera. Do not crash, push or press the lens hard otherwise, an injury or a product damage may be caused. Please protect the product from dropping or being strongly impacted. In case of dropping down or a product damage, do not touch the inside part of the product so as to prevent any harm. Stop using it immediately if the product emits smoke or any peculiar smell or there occurs any other abnormal situation.
Do not expose the dash camera to a temperature lower than -0 or higher than 65. Otherwise, a possible battery leakage, overheating or an explosion may happen, resulting in a fire, an electric shock, burns or other injuries. -- High temperature can shorten the life span of the device, and extremely high temperature will shorten the battery and/or degrade the plastic components. Please note that extreme temperatures can be achieved in parked cars in direct sunlight. -- Expose the dash camera in sunlight with Motion Detection mode may cause the dash camera crash or damaged as the temperature is too high in your car in summer. Do not expose the dash camera to dusty, dirty, or wet areas, if this gets into the camera or on the lens, damage to components can be caused. Product Structure 8 2 3 4 5 6 7 3 9 0 2. 3M Sticker 4. Up/Mute Button (a long press for the menu) 7. Indicator Light 0. HDMI Port 3. GPS Tracker/Mounting Bracket (Angle adjustable) 2. USB Port - 5 OK Button 8. Lens. USB Port -2 3. AV Port 6.Down/Lock File Button 9. MicroSD Card Slot 2. Power Button 2
Initial Use and Installation Insert the MicroSD Card: Insert an appropriate microsd card into the dash cam to record to the external microsd card. Only after a microsd card (with a memory of no more than 28G) is correctly inserted into the camera will it work properly. It is recommended to use microsd card which reads and writes faster than Class 6. Power On/Power Off: Short press the "Power" button to boot the machine, meanwhile the blue light will light up. And the short press the OK button to start recording video. Extended press the "Power" button to shut it down and the blue light will go out. The camera will shut down automatically when having given a low power indication. After connecting with vehicle power, it is supported to automatically start recording when the car is starting, and when the car is off the video will be saved automatically then the recorder will be turned off. The dash camera is preconfigured for a simple plug and play experience with the most popular options; if you want further customize the settings, should you require a slight different experience, please refer to section SETTING. Installation Instructions: Take the SplashETech Mini0805 out of the package, install the GPS tracker correctly; then, tear off the 3M Sticker, and stick the camera into an appropriate position on the front windshield. Switch the GPS tracker to get a proper angle. Operatio Normal mode: After turning on the recorder, it will automatically enter a video mode, please short press the OK button to stop recording and go to normal mode for picture-taking and settings. Video Mode: When having started up the camera, short press the OK button to start or stop recording. In the upper right corner of the screen, there will appear a flashing red dot and the recording time, which indicates the start of recording. 3
Photo Mode: After turning to the normal mode, extended press the OK button to take pictures. The screen will flash once to indicate the completion of a picture. Reviewing Videos and Photos: After starting up the camera, extended press the DOWN button to enter the video interface, extended press the DOWN button again to enter the picture interface. Then extended press the UP button to enter file editing interface, and continuously short press the UP and DOWN button to switch between each setting (file protect operation, auto play, delete file); when having selected a item or a sub-item which need to be modified, short press the OK button, ans extended press the UP button to go back from a sub-item. In case of no modification, extended press the UP button to go back to the picture/video file interface. Extended press the DOWN button on the picture interface to go back to normal mode. USB Mode: Connect to PC by USB cable, and then we can access video or photo files. SOS Function: During camera shooting, short press DOWN button, the current video will be locked and saved as a file that cannot be deleted. To unlock the file once again, just short press the button again. One Button Mute Function: Short press the UP button to switch on/off during recording. Setting In the normal mode, extended press the UP button to call up the function setting menu. Continuously short press the UP and DOWN button to switch between each setting; when having selected the item which need to be modified, short press the OK button. Before using the dash camera it may be necessary to change some of the default setting for your own customization, for example the driver number is defined by you and the date may need updating when first powered on. The camera will automatically update the real time when GPS connected, for the camera with GPS module. The settings on the menu are as follows: 4
. Resolution: 2560 080 30p 2:9, 2304 296 30p 6:9, 920 080 45p 6:9, 920 080 30p 6:9, HDR 920 080 30p 6:9, 280 720 60p 6:9, 280 720 30p 6:9 Higher resolution videos will take more storage space. 2.Quality: Super Fine (S. Fine)/Fine/Normal The quality will affect video grain, sharpness, contrast and so on. Better quality videos will result in higher bit rate and take more storage space. 3.Photo size: 3M(4800 2700 6:9), 9M(4000 2250 6:9), 4M(2588 52 6:9) 4.Photo quality: Super Fine (S. Fine)/Fine/Normal 5.AE Meter mode: average/spot/central This setting will affect the video brightness and quality. "central metering" is recommended if there is no special requirement. 6.LDWS detection: on/off Lane Departure Warning System. The camera will warn when it detects a lane departure, including normal planned lane departure. Here you can define the speed threshold above which the LDWS will become active. 7.LDWS calibration: This adjusts the LDWS reference lines to improve the LDWS operation. Please use the UP and DOWN buttons to move the top line to the height of the horizon and the bottom line to the height of the front of your car. Use the OK button to confirm the adjustment of each line. 8.Flicker: auto/50hz/60hz Here you can set the sensor flicker frequency to fit your AC power frequency and reduce the effect of flickering lamps. Please leave it AUTO if you don t know which frequency is in use in your country. 5
9.White balance: auto/sunny/cloudy/tungsten/fluorescent Here you can set the image white balance mode to improve color balance in videos/images in different weather and lighting conditions. Auto is recommended to fit most conditions. 0.EV: -2.0/-.7/-.3/-.0/-0.7/-0.3/0/+0.3/+0.7/+.0/+.3/+.7/+2.0 Here you can manually adjust the Exposure Values to improve the image brightness..recycle: off/ min/3 mins/ 5 mins The video and data is stored on the memory card, this can either be a continuous recording or a segmented loop recording of min, 3 mins or 5 mins blocks. When "off" is chosen, the videos recording will continue until the card space is full. Once the memory is full a "card full" message will be displayed on screen and recording will stop. Please be aware that the maximum video file size is 4GB. When " min/3 mins/ 5 mins" is chosen, the dash camera will record in segment specified by the loop tome interval selected. Once the memory is full the oldest file will be overwritten with the new recording (unless the files are locked). 2.Motion detection: off/low/meddle/high Motion detection is used to reduce the amount of storage space used. When there isn t obvious motion detected the camera will switch to standby. Once motion over the threshold value is detected, the camera will start recording and continue until 5 seconds after the motion stops. Here you can set the detection sensitivity. 3.Time setup: The date/time information will be automatically updated if the GPS satellites are connected. You can set the system time manually. 6
4.Auto power off: off/ min/3 mins/5 mins If there are no button actions when the camera is on standby, the camera will auto power off to save power (unless the camera is on Motion Detection mode). Here you can define the delay time. 5.Power off screen: off/ min/3 mins/5 mins 6.Stamp: date and time/driver number stamp/off After opening this function, relevant information will be shown in the screen when a video is replayed on the computer. There are options to show the date and time, driver serial number or off. Not all the information will fit onto the video stamp do the decision needs to be made as to which information is deemed most relevant. 7.Driver number: Here you can define the driver number or your customized information with 9 characters or numbers to help identify the recording. 8.GPS stamp: on/off 9.Velocity stamp: on/off 20.G-sensor sensitive: 2G/2.5G/3G/3.5G/4G/4.5G/close The G-sensor is used to detect the 3-axis impacting forces. If any impact over the threshold value is detected, the current recording file will be locked/protected to avoid being over-written, and this is important in a crash as you may become disoriented or not able to lock the file which has recorded the incident. The level of sensitivity is set by selecting the required amount of G Forces to cause the video to lock. 2.GPS: on/off After installing a GPS tracker correctly, start up the GPS function in menu setting. When the icon appears on the main interface, it means that GPS can be used normally. When the function has been started, all videos and pictures recorded by the camera will contain GPS positioning and tracking information, which can be shown on the computer by special software, which can be downloaded via http://www.splashetech.net/. 7
22. Speed unit: Km/H/MpH/off 23. Language: English/simplified Chinese/traditional Chinese/Russian 24. Default settings: yes/no This function allows the device to be reset to factory setting. 25. Format: yes/no This is to format the memory card, which will remove all the data. 26. Software version: This shows the software version installed on the dash camera. Part of the Icons 5 Camera mode Segmented loop recording time GPS Positioning succeeded Auto mode of white balance Battery A microsd card has been inserted Motion detection Product Specifications Image sensor Main control chip Lens Lens parameters Display screen Video compression format Video file format ISO sensitivity Photo format OV4689 AmbarellaA7LA50 20 wide-angle lens 6G, F2.0, f3.0mm.5 inch HD TFT H.264 MOV Auto JPG 8
HDR Microphone and speakers AV video output HDMI video output Memory card Battery Video play software Temperature requirement for the Work Environment Humidity requirement for the Work Environment Supported Supported Supported Supported TF card (no more than 28GB) 3.7V 320mA polymer lithium battery Media player/km player -0 ~ 65 5%RH~60%RH Troubleshooting Under normal operating conditions, if the product has problems, please refer to the following solutions: Cannot take pictures or videos Check if microsd card has enough space or is locked, or if you have Loop Recording on that the files are not all protected. It tends to automatically shut down once a while after being connected to the power supply Please check whether the automatic shutdown function is started. Camera stops recording occasionally Because the data stream of high-definition video is huge, please use a high-speed Class 6 microsd card that is compatible with SDHC. GPS information can t be displayed when watching the video on the computer Please check whether the GPS module is correctly installed. When the icon occurs in the camera s screen, it indicates that the GPS positioning has failed. When the icon occurs, it indicates that the GPS positioning is being done. 9
"File error" displays when replaying the pictures and videos Please use the "Format" function to reformat the microsd card as a certain error having occurred when data are saved into the microsd card. Please format the card on a computer to be FAT32 format if it is bigger than 32GB. The image is blurred Please check whether there is anything dirty or any finger print on the lens; please wipe the lens with a piece of lens paper before recording or picturing. Please remember to remove the lens protecting film before use. The image is rather dark when picturing or recording the sky, water or other scenes The automatic exposure function of the camera will be affected in case of a scene with a severe contrast. Please conduct modification by adjusting the "EV" value in the camera s setting menu. The color isn t perfect on a cloudy day or under indoor lighting conditions Please check the "white balance" function and see whether it is set in the auto mode. The system crashes Please extended press the "Power" button to restart the camera. Video file cannot be played normally (no audio, or no image) This is due to the current video player cannot fully support the MOV video format, please try other video plays, or go to the official website: http//www.splashetech.net to download the dedicated video player: SplashETech Mini0805 GPS Player. No image displayed on TV/DVD screen Please confirm the AV, HDMI cable is connected correctly, and the TV/DVD is set to the correct AV, HDMI mode. 0
Power indicator doesn t work If the power supply is less than 600mA current, the camera can t be charged and the power indicator will not work. Image has horizontal stripes interference This is due to the wrong setting of flicker. Please adjust it depending on the local power supply frequency, reset the Flicker: 50Hz/60Hz. Camera doesn t auto start recording when the car engine is started Please make sure that the loop recording is /3/5 minute(s), not OFF, because it won t auto start recording when loop recording is OFF; additionally, please check if the microsd card is full, if yes you may try to format the microsd card. The camera continues automatic recording and won t stop This perhaps because that the camera is working on Motion Detection mode; you can check whether there is an icon on the screen. When the Motion Detection is ON, it will auto start recording when a moving object appears within the range of camera. When the motion ceases, the recording will stop automatically until a moving object appears again. It will not automatically shut down until power goes off. What to do if the camera has locked up and will not respond to button presses Remove the camera from the mount or turn off the power, then hold the power button for 20 seconds, the camera will auto reset. www.splashetech.net support@splashetech.net Sam Direct Global Trade Co., Ltd