Dear user! [ Table of Contents ]

Transcription

1 Dear user! Thank you for buying Neoline Wide S45 video recorder. Study this manual thoroughly in order to use the device correctly and to make its service life longer. Do not throw the user manual away because you may need to consult it in future. [ Table of Contents ] Operating conditions...2 Technical characteristics...3 Completing parts...3 Description of connectors and buttons...4 Meaning of buttons...5 Special functions...6 Operation guide...9 System menu...10 Video mode Photo mode Playback mode Settings Possible problems and their causes

2 [Operating conditions] Get acquainted with warranty service terms. Before launching the device, charge its in-built battery fully using a car power supply adapter included in the kit. In cars with feeding supplied to 12/24 V car socket after the engine switch off, it is necessary to disconnect the video recorder from the electric car power system (to remove adapter from 12/24 V socket) in order to avoid car battery discharge. In cars with feeding supplied to 12/24 V car socket after the engine switch off, it is necessary to disconnect the video recorder from the electric car power system (to remove adapter from 12/24 V socket) in order to avoid car battery discharge. Use Micro SD cards no lower than Class 10 to avoid loss of data during the recording. We recommend using memory cards from 8GB to 32GB. Operate your video recorder using accessories only from the supplied kit. Neoline Company is not liable for any damage to the device due to the application of accessories made by other manufacturers. Format Micro SD cards once in two months to avoid damage to its file system. Before launching the device, charge battery three hours. Also, replenish the battery charge once in two months if the device has been idle long. Monitor the storing and operating temperature conditions (see technical characteristics). Avoid prolonged exposure to the sun. Do not expose the product to excessive heat, humidity or chemically active substances (gasoline, solvents, reagents, etc.).. Disassembling or modifying of the device is forbidden Neoline Company is not liable for the loss of data and/or any damage direct or indirect sustained by the user or a third party due to improper usage of the device or software, inadequate installation, or application of accessories that are not included in the accessory kit. 2

3 [ Technical characteristics] CPU: GP3159 Image sensor: Silicon Image CF02 Viewing angle: frontal camera 155 degrees Additional camera 50 degrees Video resolution: basic camera Full HD 1920x1080 (30 fps), additional camera VGA 640x480 (25 fps) Video recording format: MOV Dual channel recording minihdmi-output Built-in battery 180 mah Display: LCD 3 inches Screen resolution: 320x200 Built-in microphone/speaker G sensor Motion detection Loop recording Continuous recording Night shot mode: no WDR Parking mode Auto switch on/off Date/time stamp Car plate number stamp MicroSD (8GB-32GB) SDHC Class 10 Operating temperature: from -10 degrees to -40 degrees Storing temperature: from -20 degrees to +60 degrees Input voltage: DC 5V, 1.5A Car charger input: DC 12-24V Dimensions (mm): 88x52x16 (35 with lens) Weight: 91g [ Completing parts ] Neoline Wide S45 video recorder Rear view camera Mounting with a suction cup Car charger Cable for rear view camera connection USB cable User manual Warranty card 3

4 [ Description of connectors and buttons ] ) Microphone 2) TF card slot 3) AV input 4) USB connector 5) Display 6) HDMI connector 7) Speaker 8) Lens 9) On/off feeding button (POWER) 10) Up button (UP) 11) Up button (UP) 12) OK button 13) Mode button (MODE) 14) Down button (DOWN) 15) Reset button (RESET) 4

5 [ Meaning of buttons ] POWER on/off button: Prolonged press switches the device on/off. Short press the button in Operating mode to switch the screen lighting on/off. UP button: Short press the button to switch between the basic and the additional camera. In Menu, this button is used for moving along Menu items (upwards); in Playback mode, it is used for selecting a video or photo for viewing / playing back. During the play back of a video, the button is used for increasing the sound volume. MENU button: Short press the button to open Settings menu; inside the menu, short press it to switch between tabs. In shooting mode, short press the button to protect current file from re-recording. In Playback mode, use it to open a window for removing or protecting the file. OK button: In Video mode, this button is used to start/pause the recording, in Photo mode to shoot a photo. In Playback mode to select a video for viewing, start / complete the play back. In Menu to acknowledge the selection of a definite item or setting. MODE button: The button is used for switching between modes: Video / Photo / Playback. In Video mode short press the button to switch on the function of current file s protection; repeated press switches the protection function off. DOWN button: In Video mode, the button switches on/off the microphone. In menu mode, it is used for moving along Menu items (downwards). In Playback mode, the button allows selecting a video/photo for viewing / play back. During the play back of a video, the button is used for reducing the sound volume. RESET button: The button is meant for resetting the device. If your video recorder fails to react to the pressing of buttons, press RESET button for forced resetting of the device. Warning: Do not apply too much force when pressing the button to avoid damage to the device. TF card slot. The slot is meant for installing MicroSD memory card into the video recorder. 5

6 Before installing the memory card switch the device off ATTENTION: Make sure that the memory card s position is right. Your attempt to insert the memory card facing the wrong direction may bring about damage to the device and also to the memory card Warning: НDo not apply too much force when installing the memory card to avoid damage to the device. In order to install the memory card insert Micro SD card into the slot pushing it down all the way (till it clicks); if needed, use an installation needle. In order to remove the card, press it until it clicks and pull it out of the slot. USB connector: USB connector is meant for charging, and connecting to computer. In order to transfer data from your device to computer, use cable from the supplied kit, switch off the device by pressing POWER button, and make sure that the device is switched off. Insert into your device mini-usb B connector, and into the computer USB type A connector. For the purpose of securing feeding (car battery charging) connect your video recorder to the car power supply network through the charger included in the kit. [ Special functions ] G sensor This function allows adjusting the sensitivity level of G sensor initiating automated protection of current video in case of violent speeding, braking, knocking, turning, or tossing on an uneven road, etc. Upon G sensor s activation, the current file is blocked from re-recording. This secures the safety of files even if the memory card has been re-recorded several times during the loop recording. Auto switch off Upon switching on this function, video recorder will switch off automatically after a previously set interval of time following the car engine s shut off. 6

7 ATTENTION: If after the engine switch off the feeding to 12/24 V car socket does not stop, the auto switch off function will not be activated. Consult your car operation documents or car manufacturer for more detailed information about your 12/24 V socket. Urgent recording function It is meant for protecting current video file from re-recording or removing. In order to protect the current video file press MODE button during video recording; the currently recorded file will get a special tag forbidding the device to emove or re-record this file. At the top of display a key icon will appear. Note: Protected files can be removed only by computer connected to the device through USB cable from the kit. This can be done by formatting the memory card, or through Menu, in Playback mode. Parking mode This function allows adjusting the G sensor s sensitivity value at which the device will start urgent recoding automatically. Recording completed, the device will switch off again unless external feeding is supplied. As soon as push or knock on your car is recorded by G sensor, recording will start automatically even if the recorder is switched off and external feeding is missing. If the video recorder gets external feeding, upon switching on, it will continue recording the video in a usual mode without switching off any more. Motion detection Upon switching on this function recording will start automatically if any motion is recorded in the frame. Note: This function is meant for a standing car. Do not switch on the motion detection when you drive the car this may lead to fragmented recording and the memory card overflow. 7

8 [Rear view camera mounting and using] 1. Mount your rear view camera as shown in Fig.1. video recorder camera red + black rear light car body 2..Fix the camera on the rear bumper by means of self-tapping screws or inside the car using 3M scotch tape (from the kit) as shown in Fig Connect video cable to the video recorder s AV input as shown in Fig Connect the power cable to the rear light wires to secure the displaying of video from rear view camera in full screen mode when you switch your car gear box to rear mode. Unless you supply feeding to the rear light wiring, the rear view camera will record a video but it will not get into full screen mode automatically. 8

9 [ Operation guide ] Connection to 12/24V car socket. Plug in the charger to 12/24 car socket. Upon starting the engine (supplying power to 12/24V car socket) the device will begin to record automatically. Upon shutting off the engine (disconnection of power supply to 12/24V car socket) the device will stop recording automatically and save recorded files. Attention: For feeding the device use a standard car charger from the kit. On/Off: Press and hold Power button 2 seconds to switch the feeding to the device on/ off. Entering Menu: Stop the recording. Press Menu button to enter Settings. A repeated press opens General settings menu. In order to move along menu items, use Up and Down buttons; for the acknowledgment of your selection press OK button. Video recording: To start video recording, switch to Video mode and press OK button; to make a pause in the recording press OK button once more. Switching the recording sound on/off: In Video mode, press Down button to switch on/off the microphone. You can do it also through Settings menu. Switching off the screen: For the energy saving purpose, in Video mode you can press POWER button to switch the screen off. Also in Settings (screen switch off) you can set an interval after which the screen will switch off automatically. Photo shooting: Press Menu button to switch to Photo mode, press OK to shoot a photo. Date/time setting: Press Menu button twice; select Date/Time item, by means of OK, Up and Down buttons set the date and time, in order to save the selected settings press Menu button. Video playback: Stop the recording by pressing OK button, then press MODE button twice; select the file you need. In order to playback/pause the video, press OK. To quite Playback mode, press MODE button. 9

10 [System menu] Menu has 4 modes: Video (settings in Video mode), Photo (settings in Photo mode), Playback (settings in Playback mode), and Settings (general settings in any mode). They allow setting different modes of video recorder s operation. Video Stop the recording, press Menu button, and select any menu item for setting. Video Description Submenu Resolution Loop recording WDR Setting the video resolution Video file duration Wide dynamic range function 1080FHD: resolution FullHD, 30 fps 720P 30FHD: resolution HD, 30 fps Off /2minutes/ 3minutes/ 5minutes On Exposure Setting the exposure value -2 to +2 Motion detection Recording of sound Date/time st amp G sensor Motion spotting function Microphone on/off Imaging the date/time stamp on a video Selecting the impact sensor s sensitivity level On/Off On/Off On/Off Off/High/Medium/Low 10

11 Photo In Photo mode, press Menu button, and select any menu item for setting. Photo Description Submenu Shooting mode Selecting the momentum photo function or timer setting Single/2sec.timer/5sec.timer/10 sec.timer Resolution Selecting the resolution 12M/10M/8M/5M/3M/2MHD/1.3/VGA Burst shot Quality Sharpness Function 3x frames in succession Selecting the shooting quality Selecting the image sharpness level On/Off Best/Medium/Usual Sharp/Medium/Soft White balance Setting the white balance Auto / Sunny / Cloudy / Filament lamp / Fluorescent Colours Adjusting the colour effects Colours/Black-white/Sepia ISO Exposure Stabilisation Date/stamp Setting the sensor sensitivity level Adjusting the exposure value Blur-reducing stabilisation function Imaging the date/time stamp on a photo Auto/100/200/400-2 to +2 On/Off Off/Date/Date/Time 11

12 Playback In Playback mode, press Menu button, and select any menu item for setting. Playback Description Submenu Remove Removing the video or image Remove current /Remove all Protection Slide show Protecting the video or image against removal Selecting the interval for automated file switch Block current/ Unblock current/ Block ALL/ Unblock ALL 2 seconds / 5 seconds / 8 seconds Settings In order to enter General settings menu press Menu button twice in any mode, and select any menu item for setting. Settings Description Submenu Parking mode Selecting the G sensor s sensitivity level of in Parking mode 12 Off/High/Medium/ Low Date/time Setting the date and time YY /MM /DD XX:XX:XX Car plate number Entering the car plate number AAAAAAAAA Button sound Switching on/off the sound upon pressing buttons On/Off Language Selecting the language English/Russian TV mode Selecting the TV mode NTSC/PAL Network frequency Selecting the network frequency 50Hz/60Hz Screen auto switch off Auto switch off Selecting the interval after which the display lighting will switch off Setting the interval after which the video recorder will be switched off Card formatting Formatting the memory card CD card Manufacturer s settings Reset of settings Off/3 minutes/5 minutes/10 minutes Off/3 minutes/5 minutes/10 minutes Cancel/Yes Software version Firmware version XXX-XXXXXXXX

13 [ Possible problems and their causes ] If any problems with the device emerge although the equipment maintenance and operation terms have been observed, read this section to solve them. - It is impossible to shoot photos and record videos. Check if there is enough free space on Micro SD card, and if it is not blocked. - Spontaneous stop occurs during the recording. Since HD quality video files occupy much space, use only high quality Micro SD cards no lower than 6 class (class 10 is recommended). -.When you try to view / back play a photo-video file, wrong file inscription appears on the display. This is caused by incomplete file recording due to the file system failure on the Micro DS card. Format your SD card. - Blurred image. Check for dirt or fingerprints on the lens. If you find any, wipe the lens with a piece of soft cloth before usage. (To avoid damage to the lens surface special substances for the maintenance of optical equipment are recommended). - Image is darkened when you shoot the sky or water. If a sharp contrast is present on the shooting scene, it will affect the exposure. Change the exposure value settings in menu. -.Unnatural colour on the recording and photo occurs when you shoot on a cloudy day or indoors. Check White balance settings in menu, set White balance in Auto mode or select the value which suits the shooting conditions. - Horizontal stripes are visible on the image. They are caused by wrong settings of the electric network frequency. Set the frequency value corresponding to the parameters of your local electric network. 13

14 - Hang (no image on the display, no reaction to pressing on buttons). For starting a forced reset of the device press RESET button. 14