CD Installation Guide for the Cisco SIP Proxy Server on Solaris (Version 1.1) The CD Installation Guide for the Cisco SIP Proxy Server on Solaris describes how to install the Cisco SIP Proxy Server software on a Sparc-based server running Solaris 2.6 or later Operating Environment. Network engineers, system administrators, or telecommunication engineers should use this guide to learn the steps required to install the Cisco SIP Proxy Server software on a Sparc-based server running Solaris. Note The tasks described are considered to be administration-level tasks. These tasks require Unix command and Unix shell knowledge. This document contains information on the following: Related Documentation, page 2 Before You Begin, page 2 Installing the Cisco SIP Proxy Server Software, page 2 Obtaining Documentation, page 9 Obtaining Technical Assistance, page 10 Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright 2000. Cisco Systems, Inc. All rights reserved.
Related Documentation Related Documentation Cisco SIP Proxy Server Administrator Guide, Version 1.1 should be used in conjunction with this CD installation guide. Before You Begin This section contains requirements and conditions that should be met before installing the Cisco SIP Proxy Server software on your Solaris machine. Before installing the Cisco SIP Proxy Server, be aware of the following: Platform Requirements The following hardware and operating system requirements must be met before installing the Cisco SIP Proxy Server software: Workstation Sparc or UltraSparc server class machine with a minimum of 256 MB of RAM and 1 GB of disk space. Solaris 2.6 Operating Environment or later For IPSec support: Solaris 2.8 Operating Environment or later Authentication and Data Encryption By default, Authentication can be used when Solaris 2.8 Operating Environment is installed. Data Encryption is available on a Solaris supplemental CD. Installing the Cisco SIP Proxy Server Software The Cisco SIP Proxy Server software is available on CD-ROM only. This section provides instructions on how to mount and unmount the Cisco SIP Proxy Server CD-ROM and install the Cisco SIP Proxy Server software. This section includes information about the following: Mounting the CD-ROM, page 3 Mounting an Exported CD-ROM Filesystem to a Local Machine, page 6 Installing the Cisco SIP Proxy Server Software, page 7 2
Installing the Cisco SIP Proxy Server Software Unmounting the CD-ROM Drive, page 8 Unexporting the CD-ROM Filesystem, page 9 Mounting the CD-ROM This section describes how to mount the Cisco SIP Proxy Server CD-ROM. There are two ways you can mount the CD-ROM: locally or remotely. On a local CD-ROM drive On a remote CD-ROM drive (exporting the CD-ROM filesystem and mounting it on a Solaris machine) 3
Installing the Cisco SIP Proxy Server Software Mounting a Local CD-ROM Drive Insert the Cisco SIP Proxy Server CD-ROM into the CD-ROM drive, then perform the following steps: Step 1 Step 2 Step 3 Enter the su command and give the root password at the prompt, or log in as root. The prompt changes to the pound sign (#). If the /cdrom directory does not already exist, enter the following command: # mkdir /cdrom Mount the CD-ROM drive. The vold daemon process manages the CD-ROM device and mounts the CD-ROM automatically onto the /cdrom/cdrom0 directory. If the CD-ROM is not mounted, mount it by entering the following command: # mount -F hsfs -r /dev/sr0 /cdrom If you see a mount error, refer to your Solaris documentation for troubleshooting information. You have mounted the Cisco SIP Proxy Server CD-ROM. To install the Cisco SIP Proxy Server software, go to the Installing the Cisco SIP Proxy Server Software section on page 7. 4
Installing the Cisco SIP Proxy Server Software Mounting a Remote CD-ROM Drive This section is for users who plan to install the Cisco SIP Proxy Server software remotely; for example, if your local machine does not have a CD-ROM drive and you need to install the Cisco SIP Proxy Server software using a remote CD-ROM drive. To mount the remote machine and export the CD-ROM, perform the following steps: Step 1 Step 2 Step 3 Log in to the remote Solaris machine as root. The prompt changes to the pound sign (#). Mount the CD-ROM on the remote machine by following the steps described in the Mounting a Local CD-ROM Drive section on page 4. Make sure that the remote machine is enabled as an NFS server. a. Determine if the remote machine is enabled as an NFS server by entering the following command: # ps -ef grep nfs grep -v grep If the output of this command contains /usr/lib/nfs/nfsd or /usr/lib/nfs/mountd, the machine is enabled as an NFS server. b. If the remote machine is not enabled as an NFS server, enter the following command: # /etc/init.d/nfs.server start Step 4 Enter the following command as root to export the mounted CD-ROM drive: # share -F nfs -o ro,anon=0 /cdrom You have mounted and exported the CD-ROM drive. For directions on mounting the exported CD-ROM on a local machine, refer to the Mounting an Exported CD-ROM Filesystem to a Local Machine section on page 6. After mounting the CD-ROM on the local machine, go to the Installing the Cisco SIP Proxy Server Software section on page 7. 5
Installing the Cisco SIP Proxy Server Software Mounting an Exported CD-ROM Filesystem to a Local Machine To mount the exported CD-ROM filesystem on to the local machine, perform the following steps: Step 1 Step 2 Step 3 Log in to the local machine as root. Create a dummy directory, for example, /local_dir. If a directory by that name already exists, create a directory with a different name. The following steps use the filename /local_dir. Verify that the directory is not already a mounted filesystem by entering the following command: # df /local_dir If the output is similar to the following, the directory is not already a mounted file system: /local_dir (/dev/dsk/c0t3d0s5):328614 blocks 586775 files If the output of the command is similar to the following, a file system is already mounted on the local_dir directory: /local_dir (remote:/tmp): 3139134 blocks -1 files Step 4 Step 5 If a file system is already mounted on the local_dir directory, unmount the existing directory by entering the following command: # /usr/sbin/umount /local_dir Mount the exported CD-ROM drive on the local machine by entering the following command: # /usr/sbin/mount -r remote_machine:/cdrom /local_dir where remote_machine is a valid IP address or host name. Note Do not manually eject a CD-ROM while it is mounted. Ensure you properly unmount the CD-ROM as described in the Obtaining Documentation section before ejecting the CD-ROM. 6
Installing the Cisco SIP Proxy Server Software Installing the Cisco SIP Proxy Server Software This section describes how to install the Cisco SIP Proxy Server after Volume Manager has been used to install the CD. If you are not running Volume Manager, mount the CD as described in the Mounting CD-ROM section above. To install the Cisco SIP Proxy Server on Solaris (local system using pkgadd), perform the following steps. Step 1 Step 2 Step 3 Insert Cisco SIP Proxy Server version 1.1 CD-ROM into the drive of the system you want to do the installation. At the system prompt of the computer you are doing the installation, log in as superuser as follows. % /usr/bin/su password: (type superuser password) # To start installation, enter the following command. # pkgadd -d /cdrom/solaris Note If CD-ROM is mounted at /mnt/cdrom, then command pkgadd -d /mnt/cdrom/solaris should be used. Step 4 At the following prompt, enter 1 or all. The following packages are available: 1 CSPS Cisco Sip Proxy Server (sparc) 1.1 Select package(s) you wish to process (or all to process all packages). (default: all) [?,??,q]: all Note 1 represents CSPS (Cisco SIP Proxy Server sparc 1.1). all represents all packages to be processed Step 5 Step 6 Carefully follow the instructions at the end of the installation. If you have existing configuration and log files, they are saved in /var/log/sipd directory. Reboot the system once you changed the system parameters. 7
Installing the Cisco SIP Proxy Server Software Cisco SIP Proxy Server runs automatically in system run-levels 3 after reboot. Unmounting the CD-ROM Drive To unmount the CD-ROM, perform the following steps: Step 1 Unmount the CD-ROM drive by entering the following commands as superuser: # umount /cdrom (for a remote CD) or # umount /cdrom/./cdrom0 (for a local CD) Step 2 Step 3 Eject the CD-ROM from the Solaris machine by entering the following command: # eject Remove the CD-ROM and store it in a safe place. 8
Obtaining Documentation Unexporting the CD-ROM Filesystem After you have finished installing the Cisco SIP Proxy Server software, you might want to unexport the exported CD-ROM filesystem. To unexport the CD-ROM filesystem, perform the following steps: Step 1 Step 2 Step 3 Step 4 Log in to the local Solaris machine as root. Unmount the directory (for example, /local_dir) from the local machine by entering the following command: # /usr/sbin/umount /local_dir Log in to the remote Solaris machine as root. Enter the following command to unexport the CD-ROM filesystem: # inshore /cdrom Obtaining Documentation World Wide Web You can access the most current Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com. Documentation CD-ROM Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly. Therefore, it is probably more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription. 9
Obtaining Technical Assistance Ordering Documentation Registered CCO users can order the Documentation CD-ROM and other Cisco Product documentation through our online Subscription Services at http://www.cisco.com/cgi-bin/subcat/kaojump.cgi. Nonregistered CCO users can order documentation through a local account representative by calling Cisco s corporate headquarters (California, USA) at 408 526-4000 or, in North America, call 800 553-NETS (6387). Obtaining Technical Assistance Cisco provides Cisco Connection Online (CCO) as a starting point for all technical assistance. Warranty or maintenance contract customers can use the Technical Assistance Center. All customers can submit technical feedback on Cisco documentation using the web, e-mail, a self-addressed stamped response card included in many printed docs, or by sending mail to Cisco. Cisco Connection Online Cisco continues to revolutionize how business is done on the Internet. Cisco Connection Online is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco. CCO s broad range of features and services helps customers and partners to streamline business processes and improve productivity. Through CCO, you will find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online support services, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available. Customers and partners can self-register on CCO to obtain additional personalized information and services. Registered users may order products, check on the status of an order and view benefits specific to their relationships with Cisco. 10
Obtaining Technical Assistance You can access CCO in the following ways: WWW: www.cisco.com Telnet: cco.cisco.com Modem using standard connection rates and the following terminal settings: VT100 emulation; 8 data bits; no parity; and 1 stop bit. From North America, call 408 526-8070 From Europe, call 33164464082 You can e-mail questions about using CCO to cco-team@cisco.com. Technical Assistance Center The Cisco Technical Assistance Center (TAC) is available to warranty or maintenance contract customers who need technical assistance with a Cisco product that is under warranty or covered by a maintenance contract. To display the TAC web site that includes links to technical support information and software upgrades and for requesting TAC support, use www.cisco.com/techsupport. To contact by e-mail, use one of the following: Language English Hanzi (Chinese) Kanji (Japanese) Hangul (Korean) Spanish Thai E-mail Address tac@cisco.com chinese-tac@cisco.com japan-tac@cisco.com korea-tac@cisco.com tac@cisco.com thai-tac@cisco.com In North America, TAC can be reached at 800 553-2447 or 408 526-7209. For other telephone numbers and TAC e-mail addresses worldwide, consult the following web site: http://www.cisco.com/warp/public/687/directory/dirtac.shtml. 11
Obtaining Technical Assistance Documentation Feedback If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. You can e-mail your comments to bug-doc@cisco.com. 12
Obtaining Technical Assistance To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address: Cisco Systems, Inc. Document Resource Connection 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate and value your comments. This document is to be used in conjunction with the Cisco SIP Proxy Server Administrator Guide publication. AccessPath, AtmDirector, Browse with Me, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, CiscoLink, the Cisco NetWorks logo, the Cisco Powered Network logo, Cisco Systems Networking Academy, the Cisco Systems Networking Academy logo, Fast Step, Follow Me Browsing, FormShare, FrameShare, GigaStack, IGX, Internet Quotient, IP/VC, iq Breakthrough, iq Expertise, iq FastTrack, the iq Logo, iq Net Readiness Scorecard, MGX, the Networkers logo, Packet, RateMUX, ScriptBuilder, ScriptShare, SlideCast, SMARTnet, TransPath, Unity, Voice LAN, Wavelength Router, and WebViewer are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That s Possible, and Empowering the Internet Generation, are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastSwitch, IOS, IP/TV, LightStream, MICA, Network Registrar, PIX, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. All other brands, names, or trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0104R) Copyright 2000, Cisco Systems, Inc. All rights reserved. 13
Obtaining Technical Assistance 14