Microcontroller Applications Chapter 1 Dr. Bradley J. Bazuin Associate Professor Department of Electrical and Computer Engineering College of Engineering and Applied Sciences
Chapter 1 Overview Basic Computer Concepts Introduction to Microprocessor Applications of Microprocessors Introduction to Microcontroller Applications of Microcontroller Microprocessor vs Microcontroller Processor, Memory, I/O ports and Peripheral modules and Software 2
Modern Computers They are everywhere and in just about everything. Ubiquitous computing Cloud computing We are all users Some of us are knowledgeable users Fewer understand basic computer architecture Fewer yet are programmers And a very few are designers, architecting and building the next generation. 3
Microcontroller vs. Microprocessor From wikipedia: http://en.wikipedia.org/wiki/microcontroller Volume About 55% of all CPUs sold in the world are 8-bit microcontrollers and microprocessors. According to Semico, over four billion 8-bit microcontrollers were sold in 2006.[http://www.semico.com] A typical home in a developed country is likely to have only four general-purpose microprocessors but around three dozen microcontrollers. A typical mid-range automobile has as many as 30 or more microcontrollers. They can also be found in many electrical device such as washing machines, microwave ovens, and telephones. 2510 This is old news there are probably more! 4
Embedded Computers in Industry The goal of general-purpose computers is to accommodate variety of the programs selected by user and execute them quickly. To meet this goal, scientist/engineers have been developing powerful computing units, sophisticated memories, complex input outputs and efficient buses. In 1970s automobile executive companies saw benefits of the computers in their cars. To make their cars reliable, safe and fuel efficient. These applications do not need general purpose computers and demanded embedded computers. 5
Computers in Industry The goal of general-purpose computers is to accommodate variety of the programs selected by user and execute them quickly. To meet this goal, scientist/engineers have been developing powerful computing units, sophisticated memories, complex input outputs and efficient buses. In 1970s automobile executive companies saw benefits of the computers in their cars. To make their cars reliable, safe and fuel efficient. These and many more applications do not need general purpose computers and demanded embedded computers. 6
Embedded Processors The embedded processors contains all necessary parts including memory and I/O ports within a single chip. These computers run at much slower memory clock and have a smaller memory size. Embedded computers can also be found in washing machine, microwave oven, camcorder, video cassette recorder, camera, cellular phone, and many other appliances. A family of embedded computers is based on the 68HC12 microcontroller. 2510 7
Other Examples of Embedded System Cell phone: making the phone call, accepting incoming call, accessing Internet, displaying Home security system: sensing external temperature, smoke, humidity, and intruders; taking appropriate actions according to the detected events Automobile: monitoring speed, gas level, temperature, distance, direction, and so on; controlling display, full injection, air bag deployment, cruising, and so on; giving warnings Network router: responsible for message routing, congestion and traffic control, and so on 8
Computers and embedded controllers All general-purpose computers or microcontrollers contain four hardware modules: 1. Central processing unit (CPU) 2. Memory 3. Input/output (I/O) devices 4. Buses CPU controls order of instruction execution, controls the access to the memory and I/O devices, performs arithmetic and logical operations, and handles interrupt services. The CPU contains an arithmetic and logical unit (ALU), a control unit, internal registers (for temporary storage) 9
The Computing Problem System or Application Requirements Algorithm and Data Structures Programming Mapping Operating System Hardware Architcture High-Level Languages Binding (Compile, Link, Load) Application Software K. Hwang, Advanced Computer Architecture: Parallelism, Scalability, Programmability, McGraw Hill, 1993. ISBM: 0-07-031622-8 Performance Evaluation 10
Six layers for a computer system development Applications Programming Environment Languages Supported Machine Independent Machine Dependent Communication Model Addressing Space Hardware Architecture K. Hwang, Advanced Computer Architecture: Parallelism, Scalability, Programmability, McGraw Hill, 1993. ISBM: 0-07-031622-8 11
The CPU The CPU contains: arithmetic and logical unit (ALU) control unit internal registers (for temporary storage) Timer related components Internal and external connections (buses). Processor Control Unit Datapath Arithmetic Logic Unit Registers Memory Program Storage Common Bus (address, data, & control) Data Storage Output Units Input Units Figure 1.1 Computer Organization 12
The Processor Registers Contain digital values Local data Data memory addresses Control Unit Handles executing the program Program counter (address of current instruction) Instruction register (describes what is to be done) Handle program flow (called branching when not linear) Arithmetic Logic Unit Arithmetic and logic operations on register or memory values 2510 13
CPU Processing Rate Speed of a CPU is based on: The clock rate (speed in Hertz) Format of an instruction (CPI: cycles per instruction) Parallel nature of instruction execution (CPI <1) Access time to its memory and I/O devices (Not likely, too slow) A 3.2 GHz machine gives information about its clock speed which is a good indication of the machine speed but it is equally important to consider other factors to measure overall performance of a computer: e.g. memory speed, I/O speed, how the software program was written, etc. 2510 14
Memory There are two types of information stored in memory: Instructions, specifying types of operations a computer executes. Such as: activities like accessing I/O, adding two numbers or logical operations Data, the actual numerical values necessary to carry out instructions. In adding two numbers the addition operation is an instruction and actual numbers being added are data. Von Neumann memory architecture (1945): stores both instruction and data in a single memory. M68HC12 has this basic structure. Harvard memory architecture: stores instruction and data in separate data memories. 15
Memory Hierarchy Registers are present in the CPU Cache is a type of memory designed to reduce memory latency by reorganizing the memory. Small memory component with fast access time is placed closer to CPU 2nd level cache is larger than first layer cache and has faster access time compare to main memory. Main memory contains all data and programs. CPU Registers Cache 2 nd level cache Main memory PCs and large computers 2510 16
Memory Types Different types of memory are RAM (Random Access Memory) Allows processor to read from and write into any location on the memory chip RAM is volatile and cannot retain data without power ROM (Read Only Memory) ROM is non volatile memory ROM data can only be read. Does not allow to perform write operations on its memory locations PROM (Programmable Read Only Memory) Can be programmed using a PROM programmer or burner Once programmed its contents cannot be changed. 17
Memory Types (Cont.) EPROM (Erasable Programmable Read Only Memory) Read only memory that can be erased by exposing it to strong ultra violet rays Requires to erase the contents of a location before writing a new value to it EEPROM (Electrically Erasable Programmable ROM) Non volatile memory that can be erased by electrical signals Requires to erase the contents of a location before writing a new value to it Allows each individual location to be erased and programmed Flash Memory Developed to overcome the drawbacks of EPROM and EEPROM Can be erased and programmed without a dedicated programmer Can be erased and programmed electrically Does not provide the facility of erasing a single location but facilitates erasure of a block of memory or entire chip 18
Buses and Peripheral Devices Buses are physical connections or pathways among the CPU, memory and Peripheral (Inout/Output) devices. There are three types of buses: 1. The address buses, is used to identify the address location where data and instructions reside in memory. 2. The data buses is used to carry actual information between CPU, memory location and I/O devices. 3. The control buses, is for sending and receiving control command such as: CPU, memory, and I/O devices. The purpose of input devices is transferring outside information into the computer, i.e. keyboard, mouse, microphone scanner. The function of output devices is allowing the computer to inform its internal states and data to the outside world. Such as: monitor, speaker, and printer. 19
Computer system A computer system is shown above. It consists of a CPU or central processing, memory containing the program and data, and I/O interface with associated input and output devices, and three buses connecting the elements of the system together. 20
Computers, Microprocessors, Microcomputers, Microcontrollers Microprocessors are CPU package in a single chip such as Intel Pentium family chip, AMD K series, Athlon. A computer that uses microprocessor as its CPU is called microcomputer, such as PC. Microprocessors require external memory and cannot directly interface with I/O devices, peripheral interface ICs are needed. Microcontroller is a package of the CPU, the memory, the I/O ports and buses in a single chip. Contains everything needed to be a stand-alone microcomputer. Typically found as an embedded computer application used to control a subsystem or device. 21
Inside an HC12 Microcontroller 2510 22
Simple Processor Diagram Registers Interactions 2510 23
Important Peripherals 24
Computer Software Computer programs are known as software. A program is a sequence of instructions. There are at least three levels of software: 1. Kernel: is a program responsible for making the computer hardware perform the instructions that a programmer wrote. 2. Operating software: is responsible for memory management, exception services, and program execution control, such as: MacOS, Windows 95, 98, 2000, XP, Linux, UNIX 3. Application program: such as: word processor, spreadsheets, email, text editor
Computer Software Microprocessor/Microcontroller Instructions/Languages Machine, Assembly, and High-Level Machine instructions: A sequence of binary digits which can be executed by the processor 0001 1000 0000 0110: [A] + [B] > A aba 0100 0011: [A] + 1 > A inca 1000 0110 0000 0110: 6 > A ldaa #06 Hard to understand, enter, debug, and maintain for human being A readable equivalent of what is performed is shown first A mnemonic for the machine instruction is shown second.
Assembly Language Defined by assembly language instructions An assembly instruction is a mnemonic representation of a machine instruction Mnemonic What it does (RTL) aba ; [A] + [B] > A deca ; [A] - 1 > A Assembly programs must be translated into machine instructions before it can be executed -- translated by an assembler There are two kinds of assemblers: native assembler and cross assembler. Programmers need to work on the program logic at a very low level and cannot achieve high productivity. 27
Assembly Language Example Loop1: ldx #Array1 ; Loads index register X with start address of Array1 ldy #Array2 ; Loads index register Y with start address of Array2 ldab #$0A ; Loads B accumulator with value 10 for counter Assembly Language Instructions Elements: Label: a defined location in the code used by compiler/assembler Opcode: descriptor of the operation to be performed Source and Destination: source and destination of operands (from where, to where) Where the next instruction comes from (usually the next instruction, increment PC) 2510 28
Machine/Assembly Code Example line addr. machine code source code 1: 2: 2000 B6 1000 ldaa $1000 3: 2003 BB 1001 adda $1001 4: 2006 BB 1002 adda $1002 5: 2009 7A 1100 staa $1100 The example shows: The address where the machine code is to be stored in memory The machine code in hex The assembly code or source code with an assembler directive The assembler directive tells the assembler at what address to start storing the machine code 2510 29
High-level Language Syntax of a high-level language is similar to English (?!) A translator is required to translate the program written in a high-level language -- done by a compiler. There are two types of compilers: native compiler and cross compiler. High-level languages allow the user to work on the program logic at higher level and achieve higher productivity. Source code A program written in assembly or high-level language Object code The output of an assembler or compiler
Machine/Assembly Code Example line addr. machine code source code 1: 2: 2000 B6 1000 ldaa $1000 3: 2003 BB 1001 adda $1001 4: 2006 BB 1002 adda $1002 5: 2009 7A 1100 staa $1100 The example shows: The address where the machine code is to be stored in memory The machine code in hex The assembly code or source code with an assembler directive The assembler directive tells the assembler at what address to start storing the machine code 2510 31
Microcontroller Used for This Class MC9S12DP512 16-bit Microcontroller manufactured by Motorola/Freescale Includes: HCS12 CPU Core (speed 24 MHz) On-Chip Debug Interface 512K Flash, 14K RAM, 4K EEPROM 91 I/O Lines, ATD Module, Timer Module, PWM, SPI, SCI, IIC and CAN modules and PLL module Widely used in the automobile industry 32
How Widely Used? http://media.freescale.com/phoenix.zhtml?c=196520&p=irol-newsarticle&id=982874 According to the U.S. Bureau of the Census, the resident population of the United States, projected to 05/11/11 is 311,331,964. Therefore, approximately 1 microcontroller for every 3 people in the US every year! 33
Application Brochure Finding This Stuff: Freescale 16-bit Microcontroller S12 and S12X S12D 2510 http://cache.freescale.com/files/microcontrollers/doc/brochure/br1871.pdf?fpsp=1&wt_type=brochures 34 &WT_VENDOR=FREESCALE&WT_FILE_FORMAT=pdf&WT_ASSET=Documentation
HCS12 CPU Registers 7 A 0 7 B 0 15 D 0 15 X 0 15 Y 0 15 SP 0 15 PC 0 S X H I N Z V C 8-bit accumulator A and B or 16-bit double accumulator D Index register X Index register Y Stack pointer Program counter Figure 1.2 HCS12 CPU registers. Condition code register Carry Overflow Zero Negative I Interrupt mask Half-Carry (from bit 3) X Interrupt Mask Stop Disable Data Registers Two 8-bit, [A] and [B] OR One 16-bit, [D] Memory index registers Two general purpose, [X] and [Y] One stack pointer, [SP] Program Counter Instruction address, [PC] Condition Code Register Bits describing completed CPU operation or instruction results [C] or [CCR] 2510
Simple Processor Diagram Registers Interactions 2510 36
Accumulator Based Machines All arithmetic or logic functions must go through the accumulator. Opcode (in the instruction register) relate the operation The destination is often explicit the accumulator. Load and store operations are use often. The accumulator sets the majority of condition code register bits. Index and Stack Pointer Registers These will be used often for addressing. There is expected to be a fixed stack and it will be used a lot. 2510 37
Condition Code Register Condition Code Register (CCR) (8-bit register) Used to keep track of the program execution status Control the execution of conditional instructions Enable the interrupt handling Most important for arithmetic S X H I N Z V C Interrupt Mask Interrupt Mask Zero Carry Stop disable Half-Carry Negative Overflow (from bit 3) 2510 38
Condition Code Register (1 of 2) Carry Flag is set when and addition/subtraction generates a borrow/carry in/out of the highest bit position Applies to unsigned integers Overflow Flag is set when addition of two positive numbers results in a negative number and vice-versa. i.e. whenever the carry from the most significant bit and the second most significant bit differs Applies to signed integers Zero Flag is set when a particular operation leads to a result of zero Negative Flag is set whenever the most significant bit of the result of an operation is 1, i.e. result is negative 39
Condition Code Register (2 of 2) Interrupt Mask When set, all maskable interrupts are disabled (detailed explanation provided during lecture on interrupts) Half Carry Flag is set whenever there is a carry from the lower four bits to the upper four bits X Interrupt Mask Stop Set during the system reset (detailed explanation provided during lecture on interrupts) Clearing this bit keeps the processor in standby mode (detailed explanation provided during lecture on interrupts) 40
Memory Addressing Memory consists of a sequence of directly addressable locations. A location is referred to as an information unit. A memory location can be used to store data, instruction, and the status of peripheral devices. A memory location has two components: an address and its contents. Address Contents Figure 1.5 The components of a memory location Addresses in our microcontroller. For our processor, a 16-bit address. Each address reads one byte (8-bits), not a 16-bit word. Physical address range, 0 to 65,535. 41
Human Readable Addressing Leading characters are used to describe a number system Decimal: 1023 Binary: %0000 0011 1111 1111 Hex: $03FF (also common 0x03FF) Octal: @001777 2510 42
Transferring Data Address bus lines CPU Memory Data bus lines Figure 1.6 Transferring data between CPU and memory Data transfers between the CPU and the memory are done over the common buses: address bus and data bus. Notations: m[addr] represents the contents of a memory location, [reg] or reg refers to the contents of a register. For example, m[$20] refers to the contents of memory location at $20. [A] or A refers to the contents of accumulator A. 43
Addressing Modes A HCS12 instruction consists of one or two bytes of opcode and zero to five bytes of operand addressing information. Opcode bytes specify the operation to be performed by the CPU. For us, the first byte of a two-byte opcode is always $18. Addressing modes specify the operand to be operated on. The addressing mode may specify a value, a register, or a memory location to be used as an operand. 44
Addressing Mode Summary 45
Addressing Modes Inherent Immediate Direct Extended (or Extended Direct) Relative (or typically PC Relative) Indexed Indexed with constant offset Indexed with a data register (accumulator) offset Indexed with auto pre-/post-increment/decrement of index register Indexed-Indirect Indexed-Indirect with a constant and index register Indexed-Indirect with a D register and index register 46
Inherent Mode Instructions that use this mode do not use extra bytes to specify operands because the instructions either do not need operands or all operands are CPU registers. Examples nop inx deca ;no operation ;increment register X ;decrement register A Operands are implied by the opcode. 2510 47
Immediate Mode (use #) Operands for instructions that use immediate mode are included in the instruction. Example ldaa #$55 ; Load register A with the value $55, A $55 ldx #$1000 ; Load register X with the value $1000, X $1000 ldx #Array1 ; Loads index register X with start address of Array1 ldy #Array2 ; Loads index register Y with start address of Array2 ldab #$0A ; Loads B accumulator with value 10 The CPU does not access a memory address or register for operands. 2510 48
Direct Mode This mode can only specify memory locations in the range of 0 255 (one byte address or two hex digits). Example ldaa $20 ;load register A with memory location $20 ; A ($0020) ldab $40 ;load register B with memory location $40 ; B ($0040) This mode uses only one byte to specify the operand address. 2510 49
Extended (Direct) Mode In this mode, the full 16-bit address is provided in the instruction (four hex digits). For example, ldaa $4000 ; load register A with memory location $4000 ; A ($4000) ldx $FE60 ; load register X with memory location $FE60 ; A ($FE60) lds $3C00 load the stack pointer to the default address This mode uses two bytes to specify the operand address 2510 50
Relative Mode (1 of 2) Used only by branch instructions that change the PC Short and long conditional branch instructions use the relative mode. That s way it s also called PC-Relative addressing A short branch instructions consists of an 8-bit opcode and a signed 8-bit offset. The short relative mode can specify a range of -128 ~ +127. A long branch instruction consists of an 8-bit opcode and a signed 16-bit offset. The range of the long relative mode is from -32768 ~ +32767. 2510 51
Relative Mode (2 of 2) For example, minus: bmi minus ; branch if minus ; if N=1, PC (PC) + 2 + Rel ; else PC (PC) + 2 A programmer uses a label to specify the branch target and the assembler will figure out the actual branch offset (distance) from the instruction that follows the branch instruction. 2510 52
Addressing Mode Summary 2510 53
Indexed Mode Overview This mode uses the sum of an index register (X, Y, or SP) and an offset to specify the address of an operand. The offset can be a 5-bit, 9-bit, or 16-bit signed value. The offset can be the value in accumulator A, B, or D. The PC may also be used as the index register for offset addressing, but it is not recommended. If offset is not needed, auto incrementing or decrementing of the index register can be performed. Automatic pre- or post-increment or pre- or post-decrement of the index registers by -1 to -8 or +1 to +8 are options. Indexed-Indirect addressing is unique as it generates the address of the address Indirect addressing with 16-bit offset or accumulator D as the offset is supported. A summary of indexed addressing modes is given in Table 1.3. 54
Indexed Addressing Modes Table 1.3 Summary of indexed operations Postbyte code (xb) source code syntax Comments rr: 00 = X, 01 = Y, 10 = SP, 11 = PC rr0nnnnn 111rr0zs 111rr011 rr1pnnnn 111rr1aa 111rr111 r n,r -n,r n,r -n,r [n,r] n,-r n,+r n,rn,r+ A,r B,r D,r [D,r] 5-bit constant offset n = -16 to +15 r can be X, Y, SP, or PC Constant offset (9- or 16-bit signed) z: 0 = 9-bit with sign in LSB of postbyte (s) -256< n < 255 1 = 16-bit 0 < n < 65535 if z = s = 1, 16-bit offset indexed-indirect (see below) r can be X, Y, SP, or PC 16-bit offset indexed-indirect 0 < n < 65536 rr can be X, Y, SP, or PC Auto pre-decrement/increment or auto post-decrement/increment; p = pre-(0) or post-(1), n = -8 to -1 or +1 to +8 r can be X, Y, or SP (PC not a valid choice) +8 = 0111... +1 = 0000-1 = 1111... -8 = 1000 Accumulator offset (unsigned 8-bit 0r 16-bit) aa: 00 = A 01 = B 10 = D (16-bit) 11 = see accumulator D offset indexed-indirect r can be X, Y, SP, or PC Accumulator D offset indexed-indirect r can be X, Y, SP, or PC 55
Indexed Addressing (1 of 3) 5-bit Constant Offset Indexed Addressing (IDX) The base index register can be X, Y, SP, or PC. The range of the offset is from -16 to +15. Examples ldaa 0,X ; load A with memory location (X + 0) stab -8,X ; store B at memory location (X - 8) 9-bit Constant Offset Indexed Addressing (IDX1) The base index register can be X, Y, SP, or PC. The range of the offset is from -256 to +255. Examples ldaa $FF,X ; load A with memory location (X + 255) ldab -20,Y ; load B with memory location (Y - 20) 56
Indexed Addressing (2 of 3) 16-bit Constant Offset Indexed Addressing (IDX2) The base index register can be X, Y, SP, or PC. This mode allows access any location in the 64-KB range. Examples ldaa 2000,X ; load A with memory location (X + 2000) staa $4000,Y ; store A at memory location (Y + $4000) 57
Indexed Addressing (3 of 3) 16-bit Constant Indirect Indexed Addressing ( [D,IDX] OR [IDX2] ) A 16-bit offset is added to the base index register to form the address of a memory location that contains a pointer to the memory location affected by the instruction. The square brackets distinguish this addressing mode from the 16- bit constant offset indexing. Example, ldaa [10,X] ; load A with memory location m[m[x + 10]] staa [D,Y] ; store A at memory location m[m[y + D]] Generate the address containing the address desired. Useful for using a table of pointers and the pointers can change in time (using jump tables) 58
Auto Pre/Post-Decrement/Increment Indexed Addressing The index register can be incremented or decremented by an integer value either before or after indexing taking place. The base index register can be X, Y, or SP. The value to be incremented or decremented is in the ranges -8 thru -1 or 1 thru 8. The index register retains the changed value after indexing. Examples staa 1,-Y ; store A at memory location (Y-1), Y Y-1 staa 1,Y- ; store A at memory location (Y), Y Y-1 ldx 2,+Y ; load X with memory location (Y+2), Y Y+2 ldx 2,Y+ ; load X with memory location (Y), Y Y+2 59
Accumulator Offset Indexed Addressing The effective address of the operand is the sum of the accumulator and the base index register. The base register can be X, Y, SP, or PC. The accumulator can be the 8-bit A or B or the 16-bit accumulator D. Example ldaa B,X ; load A with memory location (X + B) stab A,Y ; store B at memory location (Y + A), 60
Example Accumulator D Indirect Indexed Addressing The value in D is added to the value in the base index register to form the address of the memory location that contains the address to the memory location affected by the instruction. The square brackets distinguish this addressing mode from accumulator D offset indexing. jmp [D,PC] ; load PC with (PC + D) go1 dc.w target1 go2 dc.w target2 go3 dc.w target3 target1. target2 target3. 61
Addressing Mode Summary 62
HCS12 Instruction Types LOAD and STORE LOAD copies the contents of a memory location or places an immediate value into an accumulator or a CPU register. STORE save the contents of a CPU register into a memory location. TRANSFER and EXCHANGE TRANSFER moves the contents of one register into another EXCHANGE swaps the contents of one register with another MOVE MOVE moves source bytes or words to defined destinations sources may be immediate values, index registers addressed memory, or memory locations destinations may be index registers addressed memory or memory locations 63
HCS12 Instruction Types (cont) ADD and SUBTRACT ADD register value with addressed memory. SUBTRACT addressed memory from a register value BCD operations perform binary coded decimal adjustments and additions INC and DEC INC increments memory locations or registers DEC decrements memory locations or registers COMPARE and TEST Operations to set the condition code registers BOOLEAN LOGIC FUNCTIONS AND, OR, and exclusive OR data registers with immediate values or memory locations 64
HCS12 Instruction Types (cont) CLEAR, COMPLEMENT and NEGATE MULTIPLY and DIVIDE BIT LEVEL TEST, SET and CLEAR SHIFT and ROTATE SHIFT register values right or left with zero fill or sign extend ROTATE register values circularly within the register BRANCH INSTRUCTIONS change program flow based on condition code values Includes looping primitives JUMP and SUBROUTINE control flow commands 65
HCS12 Instruction Types (cont) INTERRUPT INDEX MANIPULATION STACK OPERATIONS CONDITION CODE MANIPULATION STOP and WAIT See section 5 of the S12CPUV2.PDF Reference Manual Reference Manual in HW Solution Web Site See Section 6 for an instruction glossary (one or more pages per instruction) 2510 66
Include or Header Files mc9s12dp256.h The C header file fore the specific processor to be included whenever compiling C code mc9s12dp256.s An assembly language source code file with all common peripheral register names equated to their correct locations. If and when specific internal CPU addresses locations are required, they can be found in this file. Either cut and paste what you need or include the entire file. 67
Load and Store Instructions 68
Transfer and Exchange Instructions Mnemonic Function Operation TAB Transfer A to B (A) B TAP Transfer A to CCR (A) CCR TBA Transfer B to A (B) A TFR Transfer register to register (A, B, CCR, D, X, Y, or SP) A, B, CCR, D, X, Y, or SP TPA Transfer CCR to A (CCR) A TSX Transfer SP to X (SP) X TSY Transfer SP to Y (SP) Y TXS Transfer X to SP (X) SP TYS Transfer Y to SP (Y) SP Mnemonic Function Operation EXG Exchange register to register (A, B, CCR, D, X, Y, or SP) A, B, CCR, D, X, Y, or SP) XGDX Exchange D with X (D) (X) XGDY Exchange D with Y (D) (Y) Mnemonic Function Operation 2510 SEX Sign extend 8-Bit operand (A, B, or CCR) D, X, Y, or SP 69
Move Instructions Move Instructions Mnemonic Function Operation MOVB Move byte (8-bit) (M 1 ) (M 2 ) MOVW Move word (16-bit) (M 1 :M 1 +1) (M 2 :M 2 +1) 2510 70
Add and Subtract Instructions 71
Instruction Tables Table information from the manual/textbook http://homepages.wmich.edu/~bazuinb/4510/addressingmodetable.pdf 72
Instruction Tables Instruction Table and Timing See Appendix A of the S12CPUV2.PDF Reference Manual Processor Cycles Needed or CPI 2510 73
Instruction Execution Cycle Instruction Execution Cycle One or more read cycles to fetch instruction opcode bytes and addressing information One or more read cycles to fetch the memory operand(s) (optional) Perform the operation specified by the opcode One or more write cycles to write back the result to either a register or a memory location (optional) 74
Instruction Queue Instruction Queue The HCS12 executes one instruction at a time and many instructions take several clock cycles to complete. When the CPU is performing the operation, it does not need to access memory. The HCS12 prefetches instructions when the CPU is not accessing memory to speedup the instruction execution process. There are two 16-bit queue stages and one 16-bit buffer. Unless buffering is required, program information is first queued in stage 1, and then advanced to stage 2 for execution. 75