SSS INSTALLATI INSTRUCTIS Section General Description The SSS is a door mounted presence sensor designed to provide safety protection for automatic swing doors. The SSS combines the most reliable active infrared technology available with Position Sensitive Detection (PSD) technology found in auto focus cameras to ensure precise pedestrian detection within the path of a moving door panel. Accessories Instructions Wire Sheath ft. (0.m) Mounting s x (mm) Jamb Hole Cover A/B Mounting s x 0 (mm) The SSS mounts near the top of the door panel out of harms way. PSD sensor technology automatically focuses the sensor lenses to dip switch controlled height settings. Pattern width can be adjusted by inserting additional PCB Sensor Units into the 7 / long extruded aluminum housing, allowing the detection zone of each module to be adjusted independently. Each PCB Sensor Unit consists of a transmitter (TX) and a receiver (RX) that transmit a precise detection pattern that functions independently of other modules. The SSSM contains a single PCB Sensor Unit and is ideal for low energy doors. The SSSL contains two PCB Sensor Units doubling the detection capability of the SSS providing safety for full energy doors. Section Mounting Information. Do not mount higher than 8 (.m).. Ensure rain or snow will not fall directly on unit.. Ensure a minimum of reflected sunlight from floor.. Avoid steamy environments.. The Aluminum Case should be located close to leading edge of door to maximize safety detection. 8' (.m) Leading edge Leading edge Section Parts Identification Components Diagram <Top view> Side CoverL Filter Cover Joint Assembly Aluminum Case Side CoverR Section Installation and Wiring Drill Mounting holes as illustrated below. When installing the SSS on both sides of the door, it may be necessary to drill a wiring hole through the door. PCB Holder Angle Stabilizer WARNING: Drilling may cause Electric Shock. Push SW Front view of Dip SW Operation LED Terminal Block SSS Options: SSSM:.7 L (9mm); PCB; Sensor SSSM 80 80 φ. 870 Castle Park Drive Indianapolis, Indiana Telephone: (7) 8 www.mssedco.com custsvc@mssedco.com Page (/MANU) SSSv0
SSS Section Installation and Wiring (continued). Unscrew and remove the End Caps and then the Filter Cover from the Housing. INSTALLATI INSTRUCTIS. Remove the main cable Terminal block from the hinge side of the.. Replace the first PCB Holder by sliding it into the Housing and fixing it in position (do not overtighten the screw). Then slide the PCB Sensor Units into the Housing with the TX lens closest to the leading edge of the door. LEADING EDGE MARK. Remove Angle Stabilizers by lifting and sliding them to the end of the Housing then push with your thumb to remove them completely. Infrared Beam Leading Edge LEADING EDGE MARK ) ) Leading Edge Infrared Beam. Remove each PCB Holder by loosening the screws and sliding them and the PCB Sensor Units out of the Housing. The Housing should now be empty. 7. Install the Jamb Hole Cover on the hinge side of the door frame parallel to where the SSS is mounted. Pull four gauge wires from the operator control to the main Terminal Block location on the hinge side PCB Sensor Unit including an additional of extra length of each wire between the Jamb Hole Cover and the SSS. Feed the wires through the Wire Sheath and then clamp it between the Jamb Hole Cover A/B Covers.. Attach the Aluminum Housing to the door using it as a template to drill the mounting holes. When installing an SSS on both sides of the door, a wiring thru hole is necessary. Drill following holes. /8 Wiring Hole 9/ Holes /8 Unit : [in. m ] TICE: When replacing the, mount the Housing as close to the leading edge of the door as possible. LEADINGEDGE MARK Max torque 0.78 Nm Clamp the Wire Sheath between the Jamb Hole Cover A/B Wires to ( 0 [mm]) the controller Jamb Hole Cover B Jamb Hole Cover A Wire Sheath 870 Castle Park Drive Indianapolis, Indiana Telephone: (7) 8 www.mssedco.com custsvc@mssedco.com Page (/MANU) SSSv0
SSS Section Installation and Wiring (continued) 8. Remove the main Cable Terminal Block from the hinge side PCB Sensor Unit and attach the four wires to it. Reconnect the main Terminal Block to the hinge side PCB Sensor Unit. WARNING: Connect the wires to the door controller using the Terminal Block. INSTALLATI INSTRUCTIS Dip Switch # = Optical Interference When two SSSs are installed in close proximity, optical cross interference between the devices may result. To prevent this set different frequency settings. 7 8 A SSS SSS B Wire size 0. to. [mm ] 7 7 Power supply ( AC/DC [V] ) Relay Output ( Common ) Relay Output ( Normal Open ) Relay Output ( Normal Close ) TEST Input ( ) TEST Input ( + ) Dip Switch # = Relay Output Hold Time This is the length of time the relay will hold on after detection is lost. 7 8 Dip Switch # + = Mask Detecting Spots Relay output options are N.O. (Normally Open) or N.C. (Normally Closed) 7 8 Extra Wire Hole through the door Connection Cable Controller Master Slave Tx Leading Edge Jamb Hole Cover Wire Sheath Master Slave Tx PLAN VIEW and Wiring Section Setup and Adjustment. Dip Switch Settings: Dip Switches are available on each PCB Sensor Unit and they all must be set for the SSS to function properly. = Default Setting Dip Switch # = TEST Input When connected to a door controller without a TEST input, set to. When connected to a door controller with a TEST input, set to. Refer to Timing Chart of Events on page. 7 8 With TEST Without TEST Without TEST 0v 0v 870 Castle Park Drive Indianapolis, Indiana Telephone: (7) 8 www.mssedco.com custsvc@mssedco.com Page (/MANU) SSSv0
SSS Section Dip Switch #, + 7 = Detection Range: The Detection Range must be set on all PCB Sensor Units. 7 7 7 7 Set NonDetection distance A 0mm 00mm 0mm 00mm 7 7 7 7 0mm 00mm 00mm 00mm 7 8 Detection Door Leaf INSTALLATI INSTRUCTIS. Detection Angle Adjustment: The detection angle can be adjusted between and in increments using the Angle Stabilizer. Example) Changing angle from to ). ()Slide. ()Lift ()Rotate. Angle Stabilizer NonDetection A ()Slide Back Side View 0 0. Timing Chart of Events Relay Output / Test Input Dip Switch # Relay Output Mode Dip Switch # Test Input T : 8 to 8 [msec] POWER N DETECTI Test Input Break the current DETECTI NTEST Supplying DC to V, make current flow from 7th terminal to th. T TEST RESPSE TEST N DETECTI T DETECTI as response to TEST NTEST 7 Sensor 7 Sensor 7 Sensor 7 Sensor 7 Sensor 7 Sensor 870 Castle Park Drive Indianapolis, Indiana Telephone: (7) 8 www.mssedco.com custsvc@mssedco.com Page (/MANU) SSSv0
SSS INSTALLATI INSTRUCTIS Section. LED Indicator Information: The Operation LED turns when each PCB Sensor unit detects a person. Normal State State NonDetect Detect Section. LED Indicator Information: The Operation LED turns when each PCB Sensor unit detects a person. Normal State Error State Error State N times N Error category Environmental error Cause Noise occurs on setting environment. The reflection level of the floor is low. Solution Execute TEACH of the Section 8 laying a sheet of white paper on the floor of the detection area. over Other Error Internal component failure Change the units.. Teaching: The following steps must be conducted without the Filter Cover. STEP : After LED stops blinking, the number of sensor units is indicated. a. Check the wiring connection and power supply b. Execute TEACHING. TEACHING is necessary make the sensor work properly (that is to learn the number of sensor units and the distance from a floor. Flash one time when the unit is one. Flash two times when the unit is two. STEP : Press the Push SW of the master unit for more than seconds. TE: If the number of units installed and the time(s) the LED flashed are not the same, check tnection of cable, and retart TEACHING. c. Check the adjustments, range and other setting. STEP : LED blinks slowly for 0 seconds in a nondetection state. Remove the person or object(s) within the detection area during this time. STEP : After STEP, LED blinks faster and starts TEACHING. If, during this period, a person or moving object is in the area, try again from STEP. 870 Castle Park Drive Indianapolis, Indiana Telephone: (7) 8 www.mssedco.com custsvc@mssedco.com Page (/MANU) SSSv0
SSS Section. Detection Area: INSTALLATI INSTRUCTIS 8. Replacing Filter Cover and End: A. First, fit the upper side of the Filter Cover along the full length of the Aluminum Case. TOP VIEW SIDE VIEW Slightly bend the Filter Cover at one end to latch it onto the bottom lip of the Aluminum Case. Slightly bend the Filter Cover at one end to latch it onto the bottom lip of the Aluminum Case. 000 9. TICE: Insure wires do not block the lenses. 000 78.7 00 0. mm 00 00 00 0 00 000 800 00 00 00 0..7 7.9 0 7. 9....7 7.9 0 B. Attaching the Joint ) Snap the Joint into the Aluminum Case. ) Slide the Joint so that it fits snugly into the Filter Cover. Make sure there are no gaps left. ) Attach remaining Filter Covers as illustrated. 7. Power On Check: Before applying power to the unit(s) check all wiring again. TICE: The Power On Check should be carried out with the Filter Cover off. Place a test object in the desired detection area to verify the detection range, angle and Dip Switch settings are correct and make necessary adjustments. Once the Power On Check is complete, turn power off to replace Filter and Side Covers. C. Cut out the Side Cover s wiring point and insert the Wire Sheath into it. 870 Castle Park Drive Indianapolis, Indiana Telephone: (7) 8 www.mssedco.com custsvc@mssedco.com Page (/MANU) SSSv0
SSS Section D. Attach the Side Cover with s provided. External Dimensions INSTALLATI INSTRUCTIS SSSM 7. (9mm).89 (8mm) 9. Final Detection Range Test: Apply power to the SSS(s) with the Filter Cover and End Caps properly installed. Confirm the unit(s) are functioning as expected. Section Technical Data Model... SSS Door Mounted Presence Sensor Detection Method... Active Infrared with Position Sensitive Detection (PSD) Measurement Max. Installed Height... 8 (.m) Detection Range... 0 to 8 (0 to.m) Range Adjustment... 0 (0m) to 8 (.m) Beam Angle Adjustment.., 0,, 0, Presence Timer... Infinity Power Supply... to V AC or DC ± 0% Power Consumption... ACV.7VA, ACV.VA (per sensor module) DCV9mA, DCVmA Output Contact... Form C Relay: DC0V 0.A NonVoltage C Test Input... ma max. @ V DC Response Time... <00mSec. Delay Hold Time...0., Sec. Temperature Range... F to 0 F (0 C to 0 C) Weight: SSSM.... lbs. (0g) Color... Black Section 7 Warranty.99 (0.mm) MS SEDCO guarantees this product to be free from manufacturing defects for years from date of installation. Unless MS SEDCO is notified of the date of installation, the warranty will be in effect for years from the date of shipment from our factory. If, during the first years, our motion detector or support device fails to operate and has not been tampered with our abused, the unit can be returned prepaid to factory and it will be repaired free of charge. After years, the unit will be repaired for a nominal service charge. This limited warranty is in lieu of all other warranties expressed or implied, including any implied warranty of merchantability, and no representative or person is authorized to assume for MS SEDCO any other liability in connection with the sale of our products. All warranties are limited to the duration of this written warranty. In no event shall MS SEDCO be liable for any special, incidental, consequential or other damages arising from any claimed breach of warranty as to its products or services. 870 Castle Park Drive Indianapolis, Indiana Telephone: (7) 8 www.mssedco.com custsvc@mssedco.com Page 7 (/MANU) SSSv0