GANTOM 7: COMPACT SEVEN COLOR DMX SPOTLIGHT USER GUIDE The Gantm 7 packs seven-clr utput int a tiny package. With a native 15 degree beam angle, this LED sptlight prduces a punchy yet sft beam with hmgeneus clr mixing even at a clse distance. Included micr-lens diffusers and the magnetic accessry hlder ffer easy beam cntrl slutins; diffusing the sptlight t a fldlight is literally a snap. Native DMX cntrl and a balanced, nn-linear dimming curve satisfies the mst demanding theming tasks. This cmpact sptlight features lime, amber, and ultravilet beynd the cmmn RGBW t achieve clrs unavailable in standard LED fixtures. With the Gantm 7, lighting designers btain a virtually unlimited clr palette in a cmpact and efficient 7-Watt LED fixture. The Gantm 7 is cnfigured using ur DMX Prgrammer app, available free fr Apple and Andrid devices. Features Full spectrum utput with 7 LED clrs. Multiple clr prfiles selectable (RGB, RGBA, RGBW, RGBAWUv, RGBAWLUv). Clr cntrl via DMX512 r DMX Prgrammer app. Precisin-tuned nn-linear dimming curve and clr balance algrithm. Standalne mde allws set and frget peratin withut DMX signal (requires DMX Prgrammer app). DMX address and cnfiguratin stred in memry. Lw vltage and minimal heat fr imprved safety ver incandescent surces. Internal cnstant current driver gives highly efficient and cnsistent utput. Minimal maintenance required with ver 50,000 hur lamp life. Indr and utdr use. Available Mdels The Gantm DMX is available in full clr RGBW r Dynamic White. It is als available as either a Spt r Fld light. Prduct Name Gantm 7 Gantm 7 PRO SKU GT77 GP277 2.1mm DC Pwer Jack fr pwer Single lcking cnnectr fr bth Cnnectr 3.5mm TRS jack fr signal pwer and signal fr use with Gantm GCable System fr use with Gantm Pr Cable system
POWER AND WIRING REQUIREMENTS The Gantm 7 has a maximum fixture wattage f 7.5W and an perating vltage f 12V DC. Fr recmmended pwer supplies check http://www.gantm.cm/pwer-supplies/ Gantm s standard DMX cntrllable light fixtures have a 2.1mm DC barrel jack fr pwer and a 3.5mm TRS jack fr the cntrl signal. Additinally, screw terminal adapters are included with every fixture t simplify custm wiring. Yu can screw bare wires directly int these adapters Rather than using a typical XLR cable fr carrying the DMX signal, standard Gantm fixtures use 3.5mm TRS cables. Gantm makes an XLR 5 Pin t 3.5mm TRS adapter (prduct number CB51) that is perfect fr cnnecting Gantm prducts t an XLR based DMX envirnment. BARE WIRE PINOUT + RED Pwer - BLUE DMX signal D+ GREEN D- YELLOW COM BLACK The Gantm 7 is als available in ur Gantm Pr cnfiguratin. This versin has a single lcking cnnectr which cmbines bth pwer and data int ne cable. This versin is cmpatible with ur G8 Pwer/Data Distributin Bx and Pr Cable system. A single cable fr pwer and data greatly simplifies installatin and the lcking cnnectr gives a secure cnnectin fr lng term use. The Gantm Pr series is recmmended fr permanent installatins.
CONFIGURING THE LIGHT FIXTURE The Gantm 7 is prgrammed and cnfigured using the free DMX Prgrammer App by Gantm. In additin t setting the DMX starting address fr the fixture, the app allws yu t save a default clr and brightness fr standalne peratin f the light fixture if the applicatin des nt require any DMX cntrl. What yu need: An Andrid r ios device fr running the Gantm Prgrammer app. Please nte that a headphne prt is required t cnnect t the device t the fixture. The iphne7 des wrk with, but yu will need t use the headphne prt adapter that is included with the phne. A male-t-male 3.5mm audi 3.5mm cable. This is the same type f cable that yu wuld use t cnnect yur Andrid r ios device t headphnes r t an AUX prt. Pwer supply fr the fixture. All Gantm fixtures accept 12v DC pwer. We recmmend using ne f ur PwerPak Mini units if yu are just ging t pwer a single fixture. The free DMX Prgrammer app by Gantm. This can be fund by searching Gantm in itunes fr an Apple device r Ggle Play fr an Andrid device If yu have a Gantm Pr series fixture, yu will als need the CB107 prgramming adapter cable First, pen the DMX Prgrammer app by Gantm. The app will pen t the screen yu see here. Frm this screen, select Generic Cnsle. The app will then prvide yu instructins n hw t cnnect the light fixture t the tablet r smartphne. Please nte the rder in which the cables shuld be cnnected. First cnnect the headphne cable t the light fixture and t the tablet/smartphne. Next, cnnect the pwer t the fixture. When prmpted by the app, tap the Next buttn and yu will be taken t the cntrl screen.
CONTROL SCREEN Address This bx shws the address that will be assigned t the fixture if yu hit the Assign Address buttn Assign Address Hitting this buttn will assign the selected address t the fixture. The light fixture shuld blink in respnse t having a new address assigned. Save buttn this will allw yu t save a settings prfile int the app. Use this if yu need t cnfigure many fixtures t have the exact same settings. Please nte that this buttn DOES NOT save the current prfile r address t the fixture. Cnsle Sliders These sliders allw yu t set intensity levels fr each channel. There are several different channel mapping ptins which are cvered in the DMX Cntrlled Operatin sectin f this dcument. Stre as Default hitting this will save the current clr and brightness t be the default state fr the light when it turns n. If the light des nt see DMX signal when it is pwered n, it will g t this state.
OTHER OPTIONS SCREEN If yu hit the Other Optins buttn n the cntrl screen, the fllwing menu appears: Reset - selecting this will reset the fixture t its default factry settings. D this if yu are running int prgramming issues. Lck/Unlck 9600 The Gantm DMX fixture can listen t either a standard DMX signal OR t the special cntrl signal that cmes frm the app. Lck 9600 will turn OFF the fixture s ability t listen t DMX and ONLY allw it t be cntrlled thrugh the app interface. Fr mst applicatins it is recmmended that yu keep UNLOCK 9600 selected. BOOT SEQUENCE FLASHING When the fixture first receives pwer, befre it enters nrmal peratin, it will first reprt its channel mapping prfile and secnd reprt its DMX address thrugh a sequence f flashes. Prfile Reprt: Thugh the Gantm 7 has seven clrs available, nt all DMX cnsles have the ability t utilize all seven f them. Sme users may prefer t perate the Gantm 7 as thugh it were an RGBW r RGBA fixture because there are readily available preset prfiles fr thse fixtures n many existing DMX cntrl envirnments. The Gantm 7 has five channel mapping prfiles available: RGB, RGBA, RGBW, (MASTER)RGBAWU, and (MASTER)RGBAWLU. Mre infrmatin n these can be fund later in the DMX Cntrlled Operatin sectin. The Gantm 7 will reprt the prfile it has selected by rapidly flashing thrugh the clrs f that prfile. There will be a slight pause, then the fixture will reprt its DMX address. Address Reprt: After reprting which channel mapping prfile is selected, The Gantm 7 will reprt its DMX address by flashing thrugh anther sequence f clrs which represent its DMX address. Red flashes indicate the first digit, green flashes indicate the secnd digit, and blue flashes indicate the third digit f the DMX address. Fr example, if the Gantm 7 is assigned t address 245 it will indicate its channel mapping prfile, then reprt its address by flashing red 2 times, then flashing green 4 times,
then flashing blue 5 times. If it is assigned t DMX address 038, it will reprt its channel mapping prfile then reprt its address by flashing red 0 times, then flashing green 3 times, then flashing blue 8 times. TURN OFF/ON bt sequence flashing: Yu may nt want yur fixture t reprt its channel mapping prfile and address every time it receives pwer. In rder t tggle the bt sequence flashes n/ff, fllw these steps. First, tap the number field next t the wrd Address. A new screen will appear asking yu t enter a DMX start address. Enter the number 512. Finally, hit the Assign Address buttn. This will nt actually change the DMX address f the light fixture, it will simply tggle the bt sequence flashing either n r ff. STANDALONE OPERATION Sme applicatins may nt require live DMX cntrl. In rder t cnfigure yur Gantm 7 fr standalne peratin, all yu must d is use the channel sliders n the Generic Cnsle screen t set the desired levels fr each channel. Once the light has the desired utput, tap the STORE AS DEFAULT buttn at the lwer left prtin f the screen t save this setting directly int the light fixture. Nw, when the light fixture receives pwer it will autmatically g t this newly saved DEFAULT setting nce it s bt sequence is cmplete. Please nte that if DMX signal is passed t the fixture while it is perating in standalne mde, the DMX signal will verride the standalne setting. DMX CONTROLLED OPERATION The Gantm 7 was designed fr use with standard DMX512 cntrl systems. In rder t maximize cmpatibility with existing cntrl hardware and sftware, the Gantm 7 has several different DMX channel mapping prfiles available. Sme users may prefer t perate the Gantm 7 as thugh it were an RGBW r RGBA fixture because there are readily available preset prfiles fr thse fixtures n many existing DMX cntrl envirnments. The Gantm 7 has five channel mapping prfiles available: RGB, RGBA, RGBW, (MASTER)RGBAWU, and (MASTER)RGBAWLU. DMX Channel Mapping Prfiles RGB RGBA RGBW (M)RGBAWU (M)RGBAWLU CH1 Red (0-100%) Red (0-100%) Red (0-100%) MASTER DIMMER (0-100%) MASTER DIMMER (0-100%) CH2 Green (0-100%) Green (0-100%) Green (0-100%) Red (0-100%) Red (0-100%) CH3 Blue (0-100%) Blue (0-100%) Blue (0-100%) Green (0-100%) Green (0-100%) CH4 Amber (0-100%) White (0-100%) Blue (0-100%) Blue (0-100%) CH5 Amber (0-100%) Amber (0-100%) CH6 White (0-100%) White (0-100%) CH7 Ultravilet (0-100%) Lime (0-100%) CH8 Ultravilet (0-100%)
ADDRESSING YOUR GANTOM DMX The Gantm 7 can be given any DMX address frm 1-506. T set yur DMX address, first cnnect the Gantm 7 t the DMX Prgrammer app by Gantm as was utlined earlier in this dcument. With the Generic Cnsle screen pen, yu shuld have full cntrl f the fixture thrugh the channel sliders. If the light fixture is cnnected t the app but is nt respnding, try pwer cycling the light fixture. Once yu have verified that the light fixture is respnding t cntrl signal frm the app, tap the number field next t the wrd Address. A new screen will pp up, prmpting yu t enter a DMX address. After yu enter yur desired DMX address, the app will return t the Generic Cnsle screen. Finally, yu must hit the ASSIGN ADDRESS buttn in rder t save the new address int the fixture. Hitting the Save buttn will nt save anything t the light fixture s memry. SELECTING A DIFFERENT DMX CHANNEL MAPPING PROFILE In rder t select the preferred DMX channel mapping prfile, yu will need t fllw the same prcedure fr addressing the fixture, but instead f a fixture address yu will enter ne f the numbers frm the fllwing table: Channel Mapping Prfiles RGB RGBA RGBW (M)RGBAWU (M)RGBAWLU Address t Enter: 507 508 509 510 511 Once yu have entered the address crrespnding t the desired prfile, hit the ASSIGN ADDRESS buttn. The light fixture shuld then cycle thrugh a sequence f clr flashes that matches the prfile yu have selected. Please nte that this will NOT actually change the DMX address f the fixture, since the fixture can nly be set t address 1-506.
BEAM SHAPING DIFFUSERS The Gantm 7 has a beam angle f 15 and a field angle f 35. Fr increasing the width f the beam, included with the Gantm 7 is a set f Brightview diffusers which are pre-cut t fit the fixture. Als included is a magnetic ring which can be used t attach the diffusers t the face f the light fixture. Each diffuser is marked by having ntches cut int the utside f it. The diffusers are described in the fllwing table: Prduct Supprt: We hpe that this guide has been effective fr learning hw t use yur Gantm DMX light fixture. Hwever, if yu run int a wiring issue, a bug in the sftware, r just a light that desn t seem t want t cperate, we at Gantm are ready t help yu ut! Just send an email t Supprt@GANTOM.cm and we will get back t yu as sn as pssible.