TABLE OF CONTENTS ABOUT THIS GUIDE... 4 INTRODUCTION... 5 PACKAGE CONTENTS... 5 SYSTEM REQUIREMENTS... 6 GENERAL FEATURES... 7 PRODUCT VIEW... 8 HARDWARE INSTALLATION... 10 NETWORKING APPLICATION... 10 INSTALLING THE PRINT SERVER... 11 USING THE UTILITIES... 12 AUTO-RUN INSTALLATION... 12 PS-UTILITY... 14 Installing PS-Utility... 14 Using PS-Utility... 15 PS WIZARD... 18 WEB CONFIGURATION... 21 WEB CONFIGURATION UTILITY... 21 STATUS... 22 Status System... 23 Status Wireless... 24 Status Network... 26 Status Active Users... 29 CONFIGURATION... 30 Configuration System... 30 Configuration Wireless... 32 Configuration Network... 35 Configuration User... 38-2 -
Configuration E-mail... 40 Configuration SNMP... 43 TOOLS... 44 Tool Print Test... 44 Tool E-mail... 45 Tool Reset... 46 Tool Factory Reset... 47 Tool Firmware Upgrade... 48 Tool Backup... 49 HELP... 50 PRINTING IN WINDOWS 95/98/ME... 51 INSTALLING THE LPR FOR TCP/IP PRINTING CLIENT... 52 ADDING LPR PRINTER PORTS... 54 PRINTING FROM WINDOWS 95/98/ME... 56 SETTING TCP/IP PRINTING SETTINGS... 59 PRINTING IN WINDOWS 2000/XP... 61 SETTING UP WINDOWS 2000 TCP/IP PRINTING... 61 SETTING UP WINDOWS XP TCP/IP PRINTING... 69 PRINTING IN MAC OS... 76 RENDEZVOUS USES IN MAC OS 10.2... 76 SETTING UP APPLE TALK/LPR PRINTING... 79 For MAC OS X User... 79 For MAC OS 9 User... 81 For MAC OS 9 User... 82-3 -
ABOUT THIS GUIDE This manual provides instructions and illustrations on how to use your 802.11g Wireless Pocket-size Print Server, including: Chapter 1, Introduction, provides the general information on the product. Chapter 2, Hardware Installation, describes the hardware installation procedure for the product. Chapter 3, Using the Utilities, helps you to install and use the software. Chapter 4, Web Configuration, completes the configuration using the web browser. Chapter 5, Printing in Windows 95/98/ME OS, lets you complete printing task through your print server in Windows 95/98/ME environment. Chapter 6, Printing in 2000/XP OS, lets you complete printing task through your print server in Windows 2000/XP environment. Chapter 7, Printing in Mac OS, lets you complete printing task through your print server in Mac Environment. Please note that the illustrations or setting values in this manual are FOR YOUR REFERENCE ONLY. The actual settings and values depend on your system and network. If you are not sure about the respective information, please ask your network administrator or MIS staff for help. - 4 -
1 INTRODUCTION TEW-P1PG is a print server that transforms virtually any stand-alone Parallel printer into a shared network printer. The TEW-P1PG provides IEEE 802.11g 54Mbps wireless interface for integrating into existing wireless network. The TEW-P1PG is designed for printers equipped with parallel compliant printer port and it is an ideal network solution to convert conventional parallel printer into a shared resource on the network. Package Contents Unpack the package and check all the items carefully, and be certain that you have: TEW-P1PG Quick Installation Guide Utility CD-ROM with User s Guide AC Power Adapter suitable for your country s electric power service. If any packaging content is missing, please contact your local dealer immediately. Please keep all packing material for further shipment as needed. - 5 -
System Requirements Operating System: Microsoft Windows 98SE/ME/NT/2000/XP/2003 Server Microsoft Windows NT (3.51 or later). Apple Mac OS (with Apple Talk support). For Web Configuration: Java-enabled web browser, such as Microsoft Internet Explorer 5.0 and Netscape Navigator 6.0. - 6 -
General Features Wi-Fi Compliant with IEEE 802.11b/g devices One RJ-45 10/100Mbps Auto-MDIX Fast Ethernet Port Includes LPR Program for Windows 95/98/ME TCP/IP Printing Supports IPP Printing for Windows 2000/XP Printing over Email Supports second HTTP port for Remote Web Configuration and IPP Printing Supports Mac 10.2 Rendezvous Zero-Configuration Function TCP/I P protocol supports DHCP, IPP, LPR, HTTP Supports Macintosh Rendezvous Zero Configuration IP Assignment supports for DHCP Supports 64/128-bit WEP, WPA Encryption IP Assignment supports for DHCP Includes Windows-Based Administrative program and Web-Based configurationbuilt-in flash memory for easy firmware upgrade 3-Year Warranty - 7 -
Product View This section describes the externally visible features of the print server. Front View Antenna Parallel Port Rear View LAN Connector LEDs DC Power Input - 8 -
There are four green LED indicators on the front panel: LEDs Pw (Power) LPT Lk (Link/Act) Description Steady light confirms that the Print Server is powered on. Steady light confirms that the print has a good connection to print server. Steady light confirms that the print server has a good connection to your wireless network. When it blinks (briefly dark), the print server is receiving/ transmitting data from/to the wireless network. - 9 -
2 HARDWARE INSTALLATION Networking Application The following diagram explains the application of your print server. - 10 -
Installing the Print Server Follow these steps for a trouble-free start of operations with your print server. 1. Confirm proper operation of the printer to be connected to the print server. 2. When you have confirmed proper operation of the printer, turn off the power. 3. Confirm that your network is operating normally. 4. Connect the print server to the network (through the RJ-45 connector of the print server). 5. While the printer is powered off, connect the print server to the printer s Parallel port. 6. Turn on the printer s power. 7. Connect the DC end of the AC Power adapter to the DC power input socket of the print server and the AC end to the wall outlet. This will supply power to the print server immediately. NOTE: This print server is built with a default IP Address. To prevent from any conflict in your network, it is recommended to use the PS-Utility program to change the IP setting when there is some other device s IP Address is the same as the print server s default IP Address. - 11 -
3 USING THE UTILITIES This chapter describes the software utilities for the print server, including how to set up your print server with these utility. The PS- Utility and PS Wizard are designed with a user-friendly interface that allows you to set up and administer the print server easily. Auto-Run Installation Insert the Installation CD-ROM into your computer s CD-ROM drive to initiate the Auto-Run program, and the menu screen will appear as below. - 12 -
User's Guide click to preview the User's Guide in PDF format for detailed information of the Print Server. Install Utility click to install PS-Utility. Please refer to the next section for detailed information on installing the utility. PS Wizard click to launch the Printer Wizard program, which is helpful to set up the printer configuration easily and quickly. Bonus Click to install the HP PhotoSmart Program Exit click to close the Auto-Run program. - 13 -
PS-Utility To avoid the conflict in your network, you can use PS-Utility to change the related settings of your print server (such as the IP address) after finishing the installation. Installing PS-Utility 1. Click Install Utility from the Auto-Run menu screen. Once executed, the Setup program will extract files to launch the InstallShield Wizard; then, click Next > in the welcome screen of InstallShield Wizard. 2. Choose the destination location. If no specific requirement, leave the default setting and click Next >. - 14 -
3. The InstallShield Wizard starts to install the software, and the Progress bar indicates the installation is proceeding. 4. When completed, click Finish. After installing the utility, the application program for the print server is automatically installed to your computer, and creates a folder in Start\Programs\PS-Utility. Using PS-Utility This section describes the operation of PS-Utility. To launch PS- Utility: 1. Click Start -> Programs -> PS-Utility, and then click the PS- Utility v3.00 item. - 15 -
2. The main screen will appear as below, and it starts to search the connected print server within the network. Your print server - 16 -
Component Features: 1. Device List: Display the connected print server within the network. 2. Control Buttons - Change IP Address: Click this button to bring up the following dialog box, allowing you to change the IP Address. In this dialog box, you can select either Manually Assign or DHCP Assign Automatically. When completed, click OK. - Update Firmware: Click this button to update the firmware of the selected print server. - Show Web Setup: Click this button to open your web browser and launch the Configuration Utility. Alternately, you can double-click the print server in the Device List to launch the Configuration Utility. - Factory Reset: Click this button to reload the factory settings of the print server. - Discover Device: Click this button to search the connected print server again. - About: Click this button to bring up a window containing the basic information of PS-Utility. - Close: Click this button to exit PS-Utility. 3. Information Field: Display the basic information of the selected print server in the Device List. 4. Status Bar: Display the system status. - 17 -
PS Wizard PS Wizard is a convenient utility that allows you to set up the print server s port connection. To launch PS Wizard: 1. Insert the Installation CD-ROM into your computer s CD-ROM drive, and click PS Wizard from the Auto-Run menu screen. The welcome screen appears as below. Click Next >. NOTE: For some specific printers, you may need to connect the printer to the computer and install the driver. In this case, connect it to the computer and install the driver first, and then connect it to the print server. - 18 -
2. In the following window, select one printer in the Printer List to set up port connection, and then click Next >. Choose one connected printer within the network. 3. Select one printer port in the Print Server List, and click Next >. Your print server name Your printer port name Choose one connected printer port. - 19 -
4. The configuration is completed, click Reboot and then Yes to restart the system. After rebooting, PS Wizard will help you to complete the port connection automatically. You can start your printing task without any complex configuration. TIP: If you use Windows 2000/XP, the system will not restart to complete the installation. - 20 -
4 WEB CONFIGURATION You can access and manage the Print Server through: 1) the enclosed software PS-Utility, and 2) a web browser. This chapter describes the second method the Web Configuration Utility, and explains how to set up your print server with the web browser. Web Configuration Utility First, launch your web browser (such as the Internet Explorer 6.0 used in this manual). Then, type http://192.168.0.1 (the default IP address) in the Address bar and press [Enter] to enter the Management screen of the Configuration Utility. TIP: The computer s IP address must correspond with the print server s IP address in the same segment for the two devices to communicate. Extensive knowledge of LAN will be helpful in configuring the print server. - 21 -
Status - 22 -
The Management screen displays the basic information of the print server, including the following four categories: System, Wireless, Network, and User. Status System As shown above, the System displays the status of your print server, printer, and network. Clicking Refresh will update the information. Device Status The information about the print server can be found in this field, including the product model, firmware version, MAC address, IP address, and up time. Printer Status The items in this field display the information of the printer, such as the given name for the printer, speed, printer status, and status of your printing tasks, etc. - 23 -
Ethernet Status You can monitor the networking status in this field, including the network connection, speed, and the packets status. Status Wireless Click the Wireless item in the left column to display the information of the wireless LAN. Clicking Refresh will update the information. - 24 -
Wireless Status The items in this field display the information of the wireless LAN, such as the connection mode (Infrastructure or Ad-Hoc), SSID, channel, data transfer rate, WEP encryption, and the packets status. - 25 -
Status Network Click the Network item to display the information of the LAN. Clicking Refresh will update the information. - 26 -
Auto IP This field contains the current settings of TCP/IP, including DHCP/BOOTP, UPnP, and MAC Rendezvous. The items in this field are configured in Configuration > Network > TCP/IP. TCP/IP Printing In this field, you can monitor the status of your printing tasks through TCP/IP. Microsoft Network Printing In this field, you can monitor the status of your printing tasks through Microsoft Network. - 27 -
MAC AppleTalk Printing In this field, you can monitor the status of your printing tasks through MAC AppleTalk. - 28 -
Status Active Users Click the User item in the left column to display the user(s) information. Users Printing Log The items in this field display the user(s) information, which include the user(s) MAC address, IP address, name, and status of printing tasks. - 29 -
Configuration Configuration System System Device In this field, you can configure the basic information of your print server. - Server Name: Assign a name to the print server. - Location (optional): Assign a location for the print server - Admin Contact (optional): Assign the Admin Contact s name for the print server. - 30 -
- Password: Enter the Administrator password (3-8 characters). To set up the password, please enter the password in the New Password box, and then enter the same one again in the Confirm Again box. Port Settings In this field, you can assign the Port Name for the print server, and the description for the LPT port. It also allows you to select the PJL Printer setting (Yes or No). NOTE: PJL (Print Job Language) has certain job requirements that must be met to work correctly. For more information, please refer to your printer s manual. - 31 -
Configuration Wireless Wireless Interface - Connection Mode: Select one of the three connection modes. Infrastructure (default) - Connects to compatibly configured wireless AP or router in a WLAN. - 32 -
Ad-Hoc - Connect to compatibly configured wireless clients in the peer-to-peer mode. - SSID: Assign the SSID in this box. You can manually input the name or select one from the pull-down menu. To search the available wireless AP within the network, click the Site Survey button. - Wireless Channel: Select the channel from the pull-down menu. The default setting is 11. - Transmission Rate: Select the data transmit rate from the pulldown menu. The default setting is Fully Automatic. WEP Encryption This field allows you to configure the settings of data encryption. Please remember that the WEP key must be set before the data encryption is enforced. - WEP Encryption: This option allows you to select Disable, 64 bits, and 128 bits for the encryption setting. - WEP Key Format: You can decide the network key to be encoded by ASCII (ASCII characters) or HEX (hexadecimal digitals). Then, enter the key(s) for the network in the Key box (1~4). - 33 -
Advanced Setting This field allows you to configure more settings, including: - Beacon Interval: Enter the number of beacon interval time in millisecond. - Preamble: This option allows you to set the length of preamble. Setting options are: Long - it is set to 144 bits; Short - it is set to 72 bits. - Authentication Type: You can set the authentication type by selecting the settings: Open System, Shared Key, and Both. TIP: Once you have changed the settings in each option, click Save to store the settings, or Cancel to abandon. - 34 -
Configuration Network TCP/IP This field contains three options that allow you to configure the TCP/IP setting: IP Address, UPnP, and MAC Rendezvous. - 35 -
- IP Address: This option allows you to set the IP address manually or automatically. When you choose Manually Assign, you should enter the related information in the following boxes, including IP Address, Subnet Mask, and Default Gateway. - DNS Server Address: DNS (Domain Name System) server is an Internet service that translates domain names into IP addresses. Enter at least one DNS IP Address in this field. - UPnP: This option allows you to enable or disable UPnP mode. - MAC Rendezvous: This option allows you to enable or disable MAC Rendezvous mode. - Second HTTP Port: The default port for communication is via port 80, and you can change it according to your network configuration. Select Enable from the option and enter the desired port number in the following box. Microsoft Network Enter the name of the Workgroup that you want the print server associated with in this field. - 36 -
AppleTalk Enter the AppleTalk Zone name in the box. In the following options, enter the related configuration, such as the printer type. - LPT Chooser Name: Display the print server s Port name. Printer Type: Enter the printer s type in this box. PostScript Level: Select from the pull-down menu (Level 1 or Level 2). Font Group: Select from the pull-down menu. TIP: Once you have changed the settings in each option, click Save to store the settings, or Cancel to abandon. - 37 -
Configuration User Printing Control By configuring the Enable User Printing Control option (Yes or No), the user in the User List is permitted to access the print server or not. For the user(s) who is not in the User List, you can also limit the access right by setting the Allow Undefined Users Printing option to Yes or No. - 38 -
Define Users You can add/delete the user(s) to/from the User List. The User List at the bottom of the screen displays the current defined user and related information for the print server. TIP: Once you have changed the settings in each option, click Save to store the settings, or Cancel to abandon. - 39 -
Configuration E-mail E-mail Account You can assign an E-mail address to the print server, so that your mail of the account can be printed out directly through the printer (ASCII text only). To enable this function, enter the E-mail account in the Print Server E-mail Address box. - 40 -
- Incoming E-mail (POP3) Server Address: Enter the server address that is used to receive your E-mail in this box. - Outgoing E-mail (SMTP) Server Address: Enter the server address that is used to send your E-mail in this box. If your mail server needs to verify the user when sending E-mail, you have to input the Account Name and Password. E-mail Notification You can set the print server to send an alter message when the printer status changes through E-mail. To enable this function, set the Enable e-mail notification for printer status changing option to Yes. Then, input the administrator s E-mail address in the Admin E- mail Address box. E-mail Printing - E-mail Printing (ASCII Text Only): Select Enable to enable the E-mail printing function. - 41 -
- Receive E-mail Interval: Enter the number in this box to set up the time (in minute) to check/receive E-mail regularly. TIP: Once you have changed the settings in each option, click Save to store the settings, or Cancel to abandon. - 42 -
Configuration SNMP SNMP Management SNMP (Simple Network Management Protocol) is a set of protocols for managing complex networks - Community 1/2/3: Enter a name in the Name box, and configure the Access Right by selecting Read Only or Read/Write from the pull-down menu. TIP: Once you have changed the settings in each option, click Save to store the settings, or Cancel to abandon. - 43 -
Tools Tool Print Test Print Test Click Test to print a test page. - 44 -
Tool E-mail Test E-mail Account Click Test to send a test E-mail to the given administrator s E-mail address. Receive E-mail Click Yes to immediately check and receive E-mail, and then print out the mail when available. - 45 -
Tool Reset Reset Click Yes to immediately reset the print server. - 46 -
Tool Factory Reset Factory Reset Click Yes to reload the factory settings of the print server. - 47 -
Tool Firmware Upgrade Firmware Upgrade When a new version of firmware is available (e.g. downloading from the manufacturer s website), you can upgrade the firmware of your print server. Click Browse to point to the firmware file, and then click Upgrade. - 48 -
Tool Backup Backup Device Configuration to File Click Backup to backup your current configuration of the print server to file and then save in the computer. Restore Device Configuration from File You can reload a configuration that you saved before. Click Browse to point to the backup file, and then click Restore. - 49 -
Help About This screen displays the information of the print server. - 50 -
5 PRINTING IN WINDOWS 95/98/ME The Print Server can provide print services to TCP/IP networks using the lpr/lpd network printing protocol. Most UNIX systems are capable of supporting lpd, as is Windows NT/2000. This LPR for TCP/IP Printing client gives Windows 95/98/Me workstations the ability to print using the lpr/lpd printing protocol. Though it is possible to print to Print Servers from Windows 95/98/Me, this capability is useful if primarily administer your network from UNIX systems, or if you want to print from workstations that are only accessible through IP routing. - 51 -
Installing the LPR for TCP/IP Printing Client Before your Windows 95/98/Me workstation can print using the LPR protocol, you will need to install the client program, as follows: 1. Make sure that you have installed the TCP/IP protocol, and have properly configured the Windows 95/98/Me TCP/IP settings. You can install the protocol from the Network control panel if necessary. 2. From the Start menu, choose the Settings submenu, then the Control Panel item within it. Windows will display the Control Panel folder. 3. Double-click on the Network icon in the Control Panel folder. 4. Click on the Add... button on the Configuration tab. 5. Windows will ask for the type of component to add. Select Client and click Add... to continue. 6. When Windows asks you to select a network client, click the Have Disk... button. - 52 -
7. Insert the Print Server installation CD in your computer s CD- ROM, enter the proper pathname (for example, D:\ lpr), and click OK. 8. Select the LPR for TCP/IP Printing client and click OK. 9. Windows will copy the necessary files, and return to the Network dialog. Click OK to let Windows restart. - 53 -
Adding LPR Printer Ports Once you have installed the client, and have enabled TCP/IP printing for the Print Servers, then you need to add a printer port for each printer you will be printing to using the lpr/lpd protocol. To add a printer port, 1. From the Start menu, choose the Settings submenu, then the Control Panel item within it. Windows will display the Control Panel folder. 2. Double-click on the Network icon in the Control Panel folder. 3. Choose the LPR for TCP/IP Printing client and click the Properties button. - 54 -
4. Click the Add Port... button to add a new lpd-accessible printer port. 5. Enter the IP address of the Print Server and the name of the printer port that you will be printing to, then press OK. Hint: You can get the Port name from the print server s system information through web browser. Please refer page 21. 6. Click OK to leave the LPR for TCP/IP Printing Properties window. - 55 -
Printing from Windows 95/98/Me After you have added the necessary printer ports, you can add a printer device for printing to the port. To enable printing to an lpraccessible printer port from Windows 95/98/Me, 1. From the Start menu, choose the Settings submenu, then the Printers item within it. Windows will display the Printers folder. 2. Double-click on the Add Printer icon in the Printers folder. Windows will start the Add Printer Wizard. Click the Next > button to continue to the next screen. 3. Choose the Network Printer selection and click the Next > button to continue. - 56 -
4. Enter the name of the port, as displayed in the LPR for TCP/IP Printing Port List. Alternatively, you can click Browse... and locate the printer port. TCP/IP printing ports are located under the Entire Network icon, within the Print Servers - TCP/IP LPR icon. - 57 -
Press OK when you have located the proper printer port. Click Next > to continue to the next step. 5. At this point Windows will ask you to choose the correct printer driver for the printer. Choose you printer s make and model from the list, or use the driver disk included with the printer. When you have chosen the correct printer, click Next > to continue. 6. Windows will then ask for a name for the new printer, and ask whether or not you want to set the printer as the Windows default printer. Click Finish (or Next >) to continue. 7. Windows may ask you whether or not you wish to print a test page to make sure that the printer will work correctly. When the test page is done printing, you will be asked whether or not the test page printed. - 58 -
Setting TCP/IP Printing Settings The lpr client s Properties dialog allows you to change several of the client s settings. To change these settings, 1. From the Start menu, choose the Settings submenu, then the Control Panel item within it. Windows will display the Control Panel folder. 2. Double-click on the Network icon in the Control Panel folder. 3. Choose the LPR for TCP/IP Printing client and click the Properties button. 4. Click on the Settings tab to access the lpr client settings. Change the settings as necessary, and press OK to let the changes take effect. - 59 -
The parameters are as follows: Communication Timeout Determines how long, in seconds, the system will wait before determining that it has lost connection with lpr/lpd print servers. Retry Interval Determines how long, in seconds, the system will wait before retrying a lost connection. Retry Times Determines how many times the system will retry a lost connection with an lpr/lpd print server. If Infinite is checked, it will retry indefinitely. Spool Path Gives the directory path where the system will temporarily store lpr/lpd print server job files. - 60 -
6 PRINTING IN WINDOWS 2000/XP Setting Up Windows 2000 TCP/IP Printing Following is the correct procedure for setting up TCP/IP LPR printing under Windows 2000. Click Start > Settings > Printers. Double Click Add Printer Select Local Printer - 61 -
Create a new Standard TCP/IP Port Click Next - 62 -
Input the IP Address of the Print Server, and the Port name of the Port that will be printed to, then click Next. Hint: You can get the Port name from the print server s system information through web browser. Please refer page 21. Select Custom, and click Settings. - 63 -
Select LPR, and put the Port name in the field labeled Queue Name. Then Click OK. Click Next. - 64 -
Click Finish The Printer Install Wizard will now prompt for drivers. Select the correct Brand and Model, or click Have Disk, to provide the Manufacturer s Driver Disk. - 65 -
Click Next. Select a Printer Name. - 66 -
Sharing can be enabled here. Also, a Test Page can be printed to confirm proper configuration. - 67 -
When the Test Page has been printed, click Finish to complete the installation. - 68 -
Setting Up Windows XP TCP/IP Printing Following is the correct procedure for setting up TCP/IP LPR printing under Windows XP. Click Start > Printer and Faxes Double Click Add a Printer Click Next - 69 -
Select Local Printer Create a new Standard TCP/IP Port - 70 -
Click Next Input the IP Address of the Print Server, and the Port name of the Port that will be printed to, then click Next. Hint: You can get the Port name from the print server s system information through web browser. Please refer page 21. - 71 -
Select Custom, and click Settings. Select LPR, and put the Port name in the field labeled Queue Name. Then Click OK. - 72 -
Click Next. Click Finish - 73 -
The Printer Install Wizard will now prompt for drivers. Select the correct Make and Model, or click Have Disk, to provide the Manufacturer s Driver Disk. Click Next. Select a Printer Name. - 74 -
A Test Page can be printed to confirm proper configuration. When the test page has been printed, click Finish to complete the installation. - 75 -
7 PRINTING IN MAC OS Rendezvous Uses in MAC OS 10.2 The latest version of MAC OS provides a new feature that is called Rendezvous. Rendezvous is a revolutionary networking technology standard that lets you create an instant network of computers and devices, which can be used throughout Mac OS 10.2 to provide innovative ways to share files and printers and even contact other people on the network. For the printer connection, the Mac OS 10.2 Print Center application uses Rendezvous to discover Rendezvous-enabled printers on the network. When you add your computer to a network, Print Center automatically discovers the available printers. All you have to do is selecting the one you want to use and then start printing. You can add a new printer to the network and all the users on the network will see the new printer automatically appear in their Print Center, without any configuration. The following instructions provide a common procedure of installing the printer: - 76 -
1. Launch Print Center. Press and hold the Option key, click the Add button. 2. Select Rendezvous from the pop-up menu. 3. When clicking the Rendezvous item, the following window appears to display the connected Rendezvous-enabled printers. Connected printer(s) - 77 -
4. Select the desired printer, and the following pop-up menu displays the printer s manufacturer. Select Generic. 5. The printer is installed into the system successfully. - 78 -
Setting Up Apple Talk/LPR Printing For MAC OS X User With MAC OS X, you can use AppleTalk or LPR printers to print through the print server. Follow the instructions below for setting up the print server: 1. After attaching the print server to your network, change the IP Address of your Macintosh computer to access the print server s web configuration. The default I P Address of the print server is 192.168.0.1. Change your IP Address to 102.168.0.x, where x is any number between 2 and 254. 2. Open the System Preference window and click Network. In the Network window, select the AppleTalk tab and check the Make AppleTalk Active option. Check this option. - 79 -
3. To print, open a document and select File > Print from the menu. Select this option. 4. Select Edit Printer List from the Printer dialog box. Select this option. 5. Click Add Printer. Then, select the desired printing protocol (AppleTalk or LPR Printers using IP). - 80 -
- AppleTalk: After selecting AppleTalk, the Port Name of the print server will be displayed. Select the Port to which the post-script printer is connected. Then, select the printer model from the dialog box. Click Add Printer to complete the Printer Port configuration. Select the Printer Port just configured in the Print window. Click Print to print your document. - LPR Printers using IP: When you select LPR Printers using IP Protocol, type the IP Address of the print server into the LPR Printer s Address field of the following window. In the Queue Name field, type in the Port Name of the post-script printer that is connected to the Print Server. Select the printer model from the dialog box, and select the printer model from the pull-down menu. Click Add to complete the process. Close all Print Center windows and select the Printer Port that was just selected. Then, click Print to print the document. Port Name of the connected printer. - 81 -
For MAC OS 9 User If you use MAC OS 9, you can use the AppleTalk network protocol for network communications over standard Ethernet or Fast Ethernet using the EtherTalk transport, or over a proprietary low-speed LocalTalk transport. Your print server can be used for network printing to PostScript printers. You can print from any MAC OS computer connected to your Ethernet network, either directly using an EtherTalk connection or indirectly through a LocalTalk-to-EtherTalk router. To set up the print server to be used for AppleTalk printing: 1. Please confirm that the AppleTalk protocol is enabled in your Macintosh computer. 2. Change the IP Address on one of the computers within your network to 192.168.0.x (where x is any number between 2-254). 3. Type 192.168.0.1 (the default IP Address) into the address field of your browser. 4. Select the Network tab and scroll to the AppleTalk protocol section. 5. If your AppleTalk network is divided into AppleTalk zones, you have to specify which zone the Print Server should be in. You should locate the print server in the same zone as most of the users who will be using it. If your network is not divided into zones, it should contain a single asterisk *. - 82 -
To print from MAC OS Client Workstations: The actual settings of selecting a PostScript printer connected to your print server may be different from the instructions provided in this section, depending on the devices and the software you are using. 1. To choose a printer connected to your print server as your MAC OS workstation s default printer, select Chooser from the Apple menu. 2. In the left column of Chooser window, select the desired item. Please confirm that AppleTalk is set to Active. A list of all networked PostScript printers will be displayed within the right column. Select Check this option. 3. Double-click the name of the Printer Port you wish to use. The Printer Ports shown are examples only. - 83 -
4. If you have not previously set this printer as the default, your computer will prompt you for a PostScript Printer Description file. Choose Select PPD. 5. Select the appropriate printer description file for your printer. Click Open. (If your printer is not listed, click Generic to use a generic printer description.) The selected printer will become your computer s default printer. You may need to choose Page Setup in any applications you have open. - 84 -
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TEW-P1PG Wireless Print Server 3 Years Warranty If a product does not operate as warranted above during the applicable warranty period, TRENDnet shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective item, or refund to customer the purchase price paid for the defective product. All products that are replaced will become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual. Warranty service may be obtained by contacting TRENDnet office within the applicable warranty period for a Return Material Authorization (RMA) number, accompanied by a copy of the dated proof of the purchase. Products returned to TRENDnet must be pre-authorized by TRENDnet with RMA number marked on the outside of the package, and sent prepaid, insured and packaged appropriately for safe shipment.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER S SOLE REMEDY SHALL BE, AT TRENDNET S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNET S PRODUCTS. TRENDn SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. AC/DC Power Adapter, Cooling Fan, and Power Supply carry - 1 Year Warranty