Package includes 1 x Remote Controller 1 x Receiver Collar 1 x Adjustable Belt 1 x Test Bulb 1x USB Charging Cable 1 x Recharger 2 x Set of Metal Probes 1 x Button Opener 1 x User Guide Controller Features 1. 100 levels of vibration. 2. 100 levels of static shock. 3. The levels can be altered by use of up & down button. 4. A tone button activates a tone on the receiver collar. 5. The system can be used for 1 or 2 receiver collars. (Only 1 collar and receiver included). 6. Remote range up to 300 meters. 7. LCD display 8. Backlight buttons 9. Rechargeable and waterproof -1-
Power Saving 1. The Receiver Collar will TURN OFF if is unused for 4 minutes. 2. Any movement will activate the Receiver Collar into STANDBY MODE. 3. The Controller will go into STANDBY MODE if there is no operation after 20 seconds and turn off after 2 minutes. Charging The Remote Controller 1. Charge the Controller by Connecting the charger connector to the charging jack 2. After you plug the charger into a standard outlet, The red LED light on the Transmitter will be lighted 3. Charge the Controller at least 6 hours for the first charge. 4. After fully charged, the red LED light will be a darker red. Charging The Receiver 1. Charge the receiver by connecting the charger connector to the charging jack. 2. After plugging the charger into a standard outlet, the red LED light inside the Collar Receiver will be lighted. 3. Charge the Collar Receiver at least 6 hours for the first charge. 4. After fully charged, the red LED light will be turned off automatically. -2-
Controller Receiver Collar Enters sleep mode after 2-3m of no operation Lights up once per 5s when working Enters sleep mode after 20s of no movement Press Mode for 1s to wake up Apply any movement to wake it up Low battery indicator: the symbol LCD screen. will show up on the right down side of the Install The Receiver s Contact Column Choose the right column for your dog between the tall one and short one, According to the size of the dog and their hair length. -3-
How To Use The Controller. 1. After charging is completed press the mode button on the controller. 2. Make sure that it is set to channel 1 (confirm on the LCD display). 3. Press the reset button on the receiver collar you should hear a beep. 4. Press the y button on the controller you should hear another beep. That means that the receiver and the controller have successfully paired. Note: If you don t hear the beep, please press the reset button on the receiver collar once again, and try the above steps. Note: since this package contains only 1 receiver, you should always make sure when you use it that it is set to channel 1-4-
5. Press the up and down buttons for collar on the right side to set levels. Note: If you fail to press the Y button after hearing the beep from the receiver collar, you need re-sync and start with pressing the Reset button of the receiver collar. TESTING THE TRAINING SYSTEM The following methods are a testing system for you to see whether this training system functions properly. Please make sure that the remote and the receiver collar have been synced successfully by following the prior steps. 1. Testing The Beep Function Press the Mode button on the Controller, to set it on Beep Mode. Note: Every time you press the Mode button it will change to another mode, so make sure that it is on the desired mode by checking on the LCD screen. Press the Y button and the receiver collar will beep, that means that the Beep Function works properly. -5-
2. Testing The LED Function Press the Mode button on the Controller, switch to LED Mode. Note: Every time you press the Mode button it will change to another mode, so make sure that it is on the desired mode by checking on the LCD screen. Press the Y button and then the receiver collar will flash, signifying that the LED Light function works. 3. Testing The Vibration Function Press the Mode button on the controller, switch to Vibrate Mode. Note: Every time you press the Mode button it will change to another mode, so make sure that it is on the desired mode by checking on the LCD screen. Confirm on the LCD display that the level is not set to 000, press the UP/DOWN button to adjust the intensity level, set anywhere from 1 to 100. Press the Y button, the Receiver collar will vibrate, that means that the Vibration function works properly. -6-
4. Testing The Static Shock Function Take out the test bulb from the plastic package and wind its metal wire on the Receiver collar s contact points. Press the Mode button switch to Shock mode. Note: Every time you press the Mode button it will change to another mode, so make sure that it is on the desired mode by checking on the LCD screen. Confirm on the LCD display that the level is not set to 000, press the UP/DOWN button to adjust the intensity level, set anywhere from 1 to 100. Press the Y button and the test bulb will flash, that means that the static shock function works properly. Thread the collar strap through the slots on the receiver. -7-
Notes for use: 1. The lifetime of the batteries vary according as how often you use the product. Therefore you should often check the batteries by hearing the beep from the Receiver Collar and watching the indicator sign on the LCD screen of the Transmitter. 2. The valid distance of the Controller means the straight-line distance between the Controller and the Receiver Collar without obstacles in between. If there are interference signals or signal screening around, the actual remote Controller distance may vary. 3. The waterproof level of the receiver is IP3 that means that it could withhold rain, even heavy rain, but putting the receiver in a cup of water will damage the receiver, so don t let your dog swim with it. 4. The waterproof level of the controller is IP2 that means it could withhold rain drops or light drizzling, so don t let it exposed to heavy rain. 5. When your dog is wearing the receiver, always make sure that the button holes are covered with the rubber especially in the rain, as it causes damage if it s open. (Tip: Use the included pin to help tighten the rubber in to the holes). 6. After the receiver was exposed to water let it dry out for a few hours in a dry place. 7. This product is for pet training. Only by training, the pet can understand the intention of its owner. Good effect can only be achieved after a period of training. 8. Training sessions should be kept positive and short, about 10-15 minutes long each time. Presently, this product is the most effective and safest tool for training your pet. Following the correct operational instructions, you can effectively train the pet and bring it no harm. Warnings: 1. Before using this collar, you should always check under the dog's neck to make sure there's no wound. 2. Do not let your pet constantly wear this collar; take it down when you re not training them. 3. Do not use this collar to connect your leash hook, use a separate collar or harness for your leash hook. 4. Keep away of reach of children and pets. 5. Do not let your pet chew on it. 6. If you see any unusual behavior on your pet by using this product, immediately stop using this product and consult a vet. -8-
Thanks for shopping Boshel we really appreciate your business and we re sure that you and your pets will enjoy the new product. As a growing company striving for perfection, your feedback is crucial for us, If you would be able to leave us your feedback it would be a great help and would be greatly appreciated. So please take the 2 minutes to rate our product on Amazon.com or any other marketplace you purchased this product. It will help us serve you better. As a valued customer of Boshel you benefit from outstanding unparalleled customer service. So if you are not completely satisfied or if the product hasn t met your expectations or if you have any questions/problems/concerns/comments please do not hesitate to contact us @ support@boshel.com we will go out of our way to assist you. All messages are being answered within 48 business hours (usually less than 12 hours). p.s. please do not contact us via the messaging system on the marketplace you bought the product, all messages should please be sent directly to the email address provided above or through the contact form on www.boshel.com This product is backed by a 1 year limited warranty, to enroll in the warranty program simply fill out the warranty application online @ www.boshel.com Please note: The warranty is only valid when you purchase the product from our exclusive sellers, they are either, BoshelDirect, or Amabus, or Deals2Reveal, all others might be counterfeit, and are not backed by our warranty. Love what you purchased? Try our other products and be even more thrilled! Visit www.boshel.com today to see our rapidly growing collection for all your pet needs. Thanks for your business and enjoy your pets! -9-