AS&D Railing System Overview AS&D Aluminum Rail with Cable Double Posts for Corners Over-the-Post Top Rail 3-3/16 Cable Spacing Rail Guidelines To comply with engineering and testing posts must be spaced no more than 50 on center. Cables are spaced at on center to eep the cable rom deecting beyond to meet code. Two posts are reuired to create a 90 degree corner and/or a 45 degree turn. Cable can either terminate at the corner or run continuously through a single corner. Top rail is reuired or all railing installations. Posts AS&D posts for level railings are all pre-drilled and ready for cable installation. Posts for stairs come undrilled to maimie installation eibility which allow the post to accommodate any stair application. All posts are available for surface mount or fascia mount and available for 36 and/or 42 rail heights. Top Rails There are 3 styles of top rail that AS&D railing utilizes: Series 200 is a contemporary at top rail most often used for level applications. Can be used for stairs with the addition of a secondary handrail system. Series 100 has a rounded prole that ualies as a graspable rail and is most commonly used for stairs. Series 400 is a at top rail that is designed to accept a wood or composite cap rail. Available Colors: Colors shown are approximate representation Pre-Drilled Intermediate Post 48 Maximum Between Posts Pre-Drilled End Post Rail Overview anufactured in the SA using aircraft grade aluminum AS&D Aluminum ail and Cable System has been designed engineered and tested specically for use with cable and is approved in all 50 states. The aluminum framewor and stainless steel cable allows for railings to be lightweight while still retaining eceptional durability. ailings will not rust rot warp or split and reuire minimal user maintenance. (Silver) 134 *Asterisk denotes NON STOCK special order. Please contact ADI customer service.
ACTUAL AS&D FREIGHT - Aluminum CHARGES WILL Rail BE APPLIED System TO for ALL AS&D Cable RAIL Railing ORDERS Cable Railing Kits for Aluminum Rail 224 SERIES AS&D Aluminum Rail and Cable - - Series 200 Top Rail Outside of Post to Outside of Post Rail Kit - Aluminum Rail System for 2-3/8 Posts Sold in kits. Cable railing kit, made in USA from 1/8 high quality 316 grade stainless steel. Includes 1 strand of cable w/swage, applicable washers, Invisiware receiver, Pull-Lock end fitting and end cap. Minimum 3 clearance between end post and structure is required. Item #: 22405 Item #: 22410 Item #: 22415 Item #: 22420 Item #: 22425 Item #: 22430 Item #: 22440 Item #: 22450 Cable Kits Over 50 - Contact Customer Service INVISIWARE RECEIVER PULL-LOCK END FITTING *Asterisk denotes NON STOCK special order. Please contact ADI customer service. 135
AS&D Series 200 Top Rail Series 200 Top Rail to achieve any length required. Field trimmable with carbide blade. End plate sold separately. 4 Top Rail (3-1/2 x 1-7/8 x 46 ) Walnut Woodgrain Walnut Woodgrain Item #: ASTR200ANO4KIT - Item #: ASTR200BLK4KIT - Item #: ASTR200BRN4KIT - Item #: ASTR200WHT4KIT - 8 Top Rail (3-1/2 x 1-7/8 x 8 ) Item #: ASTR200ANO8KIT - Item #: ASTR200BLK8KIT - Item #: ASTR200BRN8KIT - Item #: ASTR200WHT8KIT - 8 - Series 200 Top Rail - Walnut Woodgrain 3-1/2 x 1-7/8 x 8 Series 200 aluminum top rail with powder coated clean look. End plate sold separately. Item #: ASTR200WAL8KIT - 8 Length, Walnut Woodgrain Series 200 Top Rail End Plate Aluminum end plate required to cap series 200 top rail ends for a Item #: ASEP200ANO - Item #: ASEP200BLK - Item #: ASEP200BRN - Item #: ASEP200WHT - Item #: ASEP200WAL - Walnut Woodgrain 136 *Asterisk denotes NON STOCK special order. Please contact ADI customer service.
AS&D Series 200 Rail Splices Aluminum Straight Splice length run. Installs with stainless steel #10 x 3/4 self drilling screws. (Not included) Item #: ASSPL200 - Straight Splice Aluminum Aluminum Aluminum 90 Degree Splice Splices top rails to make a 90 degree angle for series 200 top rail. Installs with stainless steel #10 x 3/4 self drilling screws. (Not included) Item #: ASSPL20090-90 Degree Splice 135 Degree Splice Splices top rails to make a 135 degree angle for series 200 top rail. Installs with stainless steel #10 x 3/4 self drilling screws. (Not included) Item #: ASSPL200135-135 Degree Splice Notched Splice for Stairs For continuos level to stair transition. Bends to accommodate any angle from 0 o - 38 o. Requires miter cutting of top rail. Installs with stainless steel #10 x 3/4 self drilling screws. (Not included) Item #: ASSPLST - Notched Splice *Asterisk denotes NON STOCK special order. Please contact ADI customer service. 137
AS&D Series 100 Graspable Top Rail for Stair Applications Series 100 Top Rail for Stairs End plate sold separately. 4 Top Rail (46 ) Item #: ASTR100ANO4KIT - Item #: ASTR100BLK4KIT - Item #: ASTR100BRN4KIT - Item #: ASTR100WHT4KIT - 8 Top Rail (96 ) Item #: ASTR100ANO4KIT - Item #: ASTR100BLK4KIT - Item #: ASTR100BRN4KIT - Item #: ASTR100WHT4KIT - Series 100 Top Rail End Plate Aluminum end plate required to cap series 100 top rail ends for a Item #: ASEP100ANO - Item #: ASEP100BLK - Item #: ASEP100BRN - Item #: ASEP100WHT - 138 *Asterisk denotes NON STOCK special order. Please contact ADI customer service.
Intermediate Post Fitting for 100 Series Top Rail Used on stair posts for over the post mounting style of 100 series top rail. Fitting attaches to the top of post and allows for top rail to be installed at any angle. Item #: ASIPFSETANO - Item #: ASIPFSETBLK - Item #: ASIPFSETBRN - Item #: ASIPFSETWHT - Aluminum AS&D Series 400 Top Rail 1 Rail Connector Block Used to terminate series 100 top rail into post. 12 connector block can be used to splice 100 series top rail together. 12 splice requires use of 8 screws to secure in place. Item #: ASRCB1-1 Connector Block - Level Item #: ASRCB12-12 Connector Block / Splice 4 - Series 400 Top Rail for Wood Cap Rail Series 400 aluminum rail cap for attaching wood/composite top rail. 4 Top Rail (2 x 1-5/8 x 46 ) Item #: ASTR400ANO4KIT - Item #: ASTR400BLK4KIT - Item #: ASTR400BRN4KIT - Item #: ASTR400WHT4KIT - 8 Top Rail (2 x 1-5/8 x 8 ) Item #: ASTR400ANO8KIT - Item #: ASTR400BLK8KIT - Item #: ASTR400BRN8KIT - Item #: ASTR400WHT8KIT - *Wood cap rail not included *Asterisk denotes NON STOCK special order. Please contact ADI customer service. 139
AS&D Surface Mount Posts Surface Mount End Post - Pre-Drilled 2-3/8 Square surface mount post with 5 base plate. Base plate holes for fasteners are 3/8. Pre-drilled post is drilled at 3-3/16 on center spacing. 10 holes for 36 rail, 12 holes for 42 rail. Engineered to meet code with posts at 50 on center spacing. Fasteners and caps for mounting base plate sold separately. 36 Rail Height (2-3/8 x 35 ) Item #: ASCEP200ANO35 - Item #: ASCEP200BLK35 - Item #: ASCEP200BRN35 - Item #: ASCEP200BWHT35-42 Rail Height (2-3/8 x 41 ) Item #: ASCEP200ANO41 - Item #: ASCEP200BLK41 - Item #: ASCEP200BRN41 - Item #: ASCEP200WHT41 - Surface Mount Intermediate Post - Pre-Drilled 2-3/8 Square surface mount post with 5 base plate. Base plate holes for fasteners are 3/8. Pre-drilled post is drilled at 3-3/16 on center spacing. 10 holes for 36 rail, 12 holes for 42 rail. Engineered to meet code with posts at 50 on center spacing. Fasteners and caps for mounting base plate sold separately. 36 Rail Height (2-3/8 x 35 ) Item #: ASCIP200ANO35 - Item #: ASCIP200BLK35 - Item #: ASCIP200BRN35 - Item #: ASCIP200WHT35-42 Rail Height (2-3/8 x 41 ) Item #: ASCIP200ANO41 - Item #: ASCIP200BLK41 - Item #: ASCIP200BRN41 - Item #: ASCIP200WHT41-140 *Asterisk denotes NON STOCK special order. Please contact ADI customer service.
Undrilled Post for Stair Applications 46 x 2-3/8 Square undrilled post for cable system. Due to many variables in stair applications stair posts are undrilled to allow custom drill hole placement for cables. Determine bottom hole location, then use drilling template for remaining holes. Intermediate stair post holes are drilled at 3-3/16 on center and offset to allow cables to pass through at the angle of the stair. See page 143 for diagram. Undrilled Post for Stair Applications Item #: ASFMP200ANO46-46 Item #: ASFMP200BLK46-46 Item #: ASFMP200BRN46-46 Item #: ASFMP200WHT46-46 Requires Base Plate for Surface Mounting Drilling Template: Use drilling template to mark 3-3/16 cable spacing on undrilled post for stair or custom applications. Item # CABLETEMP AS&D Mounting Brackets and Hardware Base Plate with Screws 5 x 5 x 3/8 Aluminum base plate used for custom post applications. Base plate holes for fasteners are 3/8. Can be used to convert fascia posts to surface mount post for stair applications. Includes 4 ea. 5/16 x 2 stainless steel screws - Use T25 torx head for installation. Item #: ASBPANOKIT - Item #: ASBPBLKKIT - Item #: ASBPBRNKIT - Item #: ASBPWHTKIT - Item # ASDINSTKIT Angle / Knee Wall Base Plate with Screws wall applications with an angle of 32 o - 38 o. Base plate holes for fasteners are 3/8.Includes 4 ea. stainless steel bolts. Use T25 torx head 5/16 x 2 Item #: ASBPKWANOKIT - Item #: ASBPKWBLKKIT - Item #: ASBPKWBRNKIT - Item #: ASBPKWWHTKIT - Item # ASDINSTKIT RED *Asterisk item numbers denotes denote NON NON STOCK STOCK special special order. order. Please Please contact allow ADI for customer 2-3 week service. lead time. 141
AS&D Fascia Mount Posts and Brackets Fascia Mount End Post - Pre-Drilled 2-3/8 Square fascia mount post for cable system. Pre-drilled post is drilled at 3-3/16 on center spacing. 10 holes for 36 rail, 12 holes for 42 rail. Engineered to meet code with posts at 50 on center spacing. Fascia brackets sold separately. 36 Rail Height (2-3/8 x 46 ) Item #: ASFMCEP200ANO46-46 Item #: ASFMCEP200BLK46-46 Item #: ASFMCEP200BRN46-46 Item #: ASFMCEP200WHT46-46 42 Rail Height (2-3/8 x 52 ) Item #: ASFMCEP200ANO52-52 Item #: ASFMCEP200BLK52-52 Item #: ASFMCEP200BRN52-52 Item #: ASFMCEP200WHT52-52 Fascia Mount Intermediate Post - Pre-Drilled 2-3/8 Square fascia mount post for cable system. Pre-drilled post is drilled at 3-3/16 on center spacing. 10 holes for 36 rail, 12 holes for 42 rail. Engineered to meet code with posts at 50 on center spacing. Fascia brackets sold separately. 36 Rail Height (2-3/8 x 46 ) Item #: ASFMCIP200ANO46-46 Item #: ASFMCIP200BLK46-46 Item #: ASFMCIP200BRN46-46 Item #: ASFMCIP200WHT46-46 42 Rail Height (2-3/8 x 52 ) Item #: ASFMCIP200ANO52-52 Item #: ASFMCIP200BLK52-52 Item #: ASFMCIP200BRN52-52 Item #: ASFMCIP200WHT52-52 142 RED *Asterisk item numbers denotes denote NON NON STOCK STOCK special special order. order. Please Please contact allow ADI for customer 2-3 week service. lead time.
Fascia Mount Intermediate Stair Post - Undrilled 2-3/8 Square fascia mount post for cable system. Undrilled post is most commonly used as an intermediate stair post to allow custom hole placement for cables. Determine bottom hole location, then use drilling template for remaining holes. Holes are drilled at 3-3/16 on center and offset to allow cables to pass through at the angle of the stair. Fascia brackets sold separately. 36 Rail Height (2-3/8 x 46 ) Item #: ASFMP200ANO46-46 Item #: ASFMP200BLK46-46 Item #: ASFMP200BRN46-46 Item #: ASFMP200WHT46-46 42 Rail Height (2-3/8 x 52 ) Item #: ASFMP200ANO52-52 Item #: ASFMP200BLK52-52 Item #: ASFMP200BRN52-52 Item #: ASFMP200WHT52-52 6 Fascia Bracket For mounting 2-3/8 post to deck fascia. Bracket offsets post 1 out from fascia. Mounting hardware is not included. Use 4 fascia screws to secure post in bracket and 4 lags or carriage bolts to secure bracket to fascia. Item # ASFMIPB200ANO6 - Item # ASFMIPB200BLK6 - Item # ASFMIPB200BRN6 - Item # ASFMIPB200WHT6 - Item # ASSSFS - 1 Fascia Screw Fascia Bracket - Outside Corner For mounting 2-3/8 posts to deck fascia. This bracket is required to maintain 4 spacing on outside corners. Bracket offsets post 1 out from fascia. Mounting hardware is not included. Use 4 fascia screws to secure post in bracket and 4 lags or carriage bolts to secure bracket to fascia. Item #: ASFMOCB200ANO6 - Item #: ASFMOCB200BLK6 - Item #: ASFMOCB200BRN6 - Item #: ASFMOCB200WHT6 - Item # ASSSFS - 1 Fascia Screw RED *Asterisk item numbers denotes denote NON NON STOCK STOCK special special order. order. Please Please contact allow ADI for customer 2-3 week service. lead time. 143
Bolt Cap w/ Stainless Steel Cup Washer Item #: ASBOLTCAPANOKIT - Item #: ASBOLTCAPBLKKIT - Item #: ASBOLTCAPBRNKIT - Item #: ASBOLTCAPWHTKIT - Stainless Steel Stainless Steel 3-1/2 Stainless Steel Lag Screw for Post Base 3-1/2 x 3/8 Lag used to attach post base to deck or for mounting fascia bracket. Item #: ASSCREWLAG4 Fascia Bracket Screws #14 x 1 Hex head stainless steel fascia bracket screw. Use for securing post to fascia bracket. Requires 4 per bracket. Item #: ASSSFS - Fascia Screw Fascia Mount Post Cap to post. Item #: ASPCANO - Item #: ASPCBLK - Item #: ASPCBRN - Item #: ASPCWHT - 144 *Asterisk denotes NON STOCK special order. Please contact ADI customer service.
AS&D Accessories Drilling Template For 2-3/8 Post Used to mark 3-3/16 cable spacing on undrilled post for stair or custom applications. Item # CABLETEMP - 40 PVC Drilling Template Stainless Steel Walnut Woodgrain Color Matched Screws Sold in 100 Pack. #10-3/4 phillips head screw attaches top rail to posts, and also used for splices. Item #: ASSCREWBLKW805 - Item #: ASSCREWBRNW805 - Item #: ASSCREWWHTW805 - Item #: ASSCREWSSW805 - Stainless Steel Item #: ASSCREWWALW805-1 - Walnut Woodgrain (sold as eaches) Touch-Up Paint Touch up paint available to cover up scratches and cuts from installation. Spray Can Item #: ASPAINTBLK - Item #: ASPAINTBRN - Item #: ASPAINTWHT - Internal Post Brace Internal post brace is used to strengthen AS&D end posts where cable tensioning is being applied. Can also be used as a splice for unique angles in the Series 200 top rail or as a splice for Series 400 top rail Item # ASEPIF36-32 length Item # ASEPIF42-40 length Paint Pen Item # 660368 - Item # 300734 - *Asterisk denotes NON STOCK special order. Please contact ADI customer service. 145
Post Base Install Kit Includes T40 Torx Bit and tube of bee s wax for screws. Apply wax to post base screws for ease of installation. Item # ASDINSTKIT AS&D Application Options Straight Cable Runs and Cable Runs Through One Corner Dec has dedicated end posts for each run and the posts are situated such that the back side of the posts are all accessible meaning you can use an outside-ofpost to outside-of-post conguration for all runs. When taking cable railing through a corner there are two options: Option 1: Terminating cable kits at each corner as shown in Deck 1. Option 2: Run cables continuously through a single corner as shown in Deck 2. For 2-3/8 posts, applicable kit is the 224 Series. The tensioning device is 2-3/ long Receiver which installs through the aluminum post on one end. A Pull-Lock tting of the same length is installed through the other end. outside mount outside mount outside mount 3½ min. House Deck 1 Deck 1 Series 224 Deck 2 AS&D Aluminum Rail and Cable - - Fascia Mount - Series 200 - Cable Through Corner Post Run #2 Run #1 3½ min. outside mount outside mount Run #3 outside mount 146 *Asterisk denotes NON STOCK special order. Please contact ADI customer service.
Cable Runs on a Pitch Due to many variables in stair applications stair posts are undrilled to allow maximum flexibility and allow custom hole placement for cables. All stair posts reuire the addition of a surface mount base plate or fascia bracket for mounting. The holes in the end posts are to be drilled straight through with a 29/64 bit and any intermediate posts must be drilled with offset holes to accommodate the angle of the stairs using a 3/16 bit. Stair Options Deck 1 - Terminating cable from level to stair. Cable Runs are broken into two sections one for level and the other for stair. This allows for the Series 100 top rail to be used for the stairs which ualies as a graspable handrail. Deck 1 Series 100 Top Rail for Stair Series 200 Top Rail on Level *Illustrations are for representation purposes only* AS&D Aluminum Rail and Cable - Series 200 (Level) Series 100 (Stair) Deck 2 - Continuous cable from level to stair. Cable runs through a single post at the top of the stairs without stopping. This can be achieved with either a Series 200 or Series 400 top rail. owever these top rails do not ualify as graspable rail and a secondary handrail will be reuired. Deck 2 Series 200 Top Rail for Both Level and Stair *Illustrations are for representation purposes only* AS&D Aluminum Rail and Cable - Series 200 (Level and Stair) *Asterisk denotes NON STOCK special order. Please contact ADI customer service. 147