Technical white paper Imaging the HP Z240 Workstation with Windows 10 Pro (64-bit) and Microsoft Deployment Toolkit (MDT) 2013 v1.2
A system image enables you to automate the deployment of computers in your organization. This document provides step-by-step guidance on how to image HP Z240 Workstations with Windows 10 Pro using the Microsoft Deployment Toolkit (MDT). It includes a list of items to consider before you start, instructions on how to set up the deployment share, deployment options, and resources for additional information. Table of contents 2 Before you begin 2 Licensing, URLs, consulting, and other OSs 2 Prerequisites 2 Required downloads 2 Optional downloads 3 MDT 2013 deployment share setup 3 Import the HP Z240 Workstation driver pack 5 Import applications for HP Z240 Workstation deployment (optional) 7 Create the HP Z240 Workstation-specific selection driver profile 8 Import Windows 10 64-bit media 9 Create an HP Z240 Workstation specific task 16 Deployment Options 16 Deploy via MDT standalone USB media 17 Update the Deployment Share 22 Format and make a USB flash drive bootable 23 Deploy via USB Discovery Media 24 Appendix: Additional HP support URLs Before you begin Licensing, URLs, consulting, and other OSs Be aware of Windows OS licensing requirements. Contact your Microsoft licensing representative for more information. The URLs in this document are reference only and are subject to change without notice. By providing this document, HP is not liable for providing any additional consulting services. Contact your HP Sales Representative or Channel Partner to arrange HP Consulting Services. This document does not cover all possible configurations of the HP Z240 Workstation. These instructions are for Windows 10 Pro, but can also be used to deploy Windows 7 64-bit on an HP Z240 Workstation. CAUTION: Imaging the HP Z240 will erase the hard drive. If the hard drive contains data that needs to be retained, create a backup of your hard drive in a separate location before proceeding with the installation. Prerequisites MDT 2013 Windows Assessment and Deployment Kit (ADK) for Windows 10 Working knowledge of MDT A management computer running Windows 10 An MDT deployment share, created on the management computer Required downloads HP Z240 Workstation Windows 10 x64 Driver Pack SP71640 Windows 10 Pro 64-bit install media To build a driver pack using HP Softpaq Download Manager; follow the instructions in the white paper, HP Driver Packs Optional downloads HP Performance Advisor HP Remote Graphics Software (RGS) 2
MDT 2013 deployment share setup Import the HP Z240 Workstation driver pack Open a command window in the folder where SP71640 resides, and enter the command: SP71640.exe /e At the MDT 2013 Deployment Workbench Console, expand the Out-of-Box Drivers section Right-click Out-of-Box Drivers, and select New Folder Create a folder: Z240 Windows10 64-bit Drivers; right-click this new folder, and select Import Drivers 3
Browse to the folder where you extracted Windows 10: SP71640 (likely in c:\swsetup\sp71640), and click OK Select the checkbox Import drivers even if they are duplicates of an existing driver and click Browse 4
You should see a list of drivers NOTE: To deploy to different system models or use multiple versions of an OS, each driver pack must have its own Outof-Box Driver folder in MDT; this reduces the risk of driver issues occurring in subsequent OS deployments. Import applications for HP Z240 Workstation deployment (optional) Download the HP Performance Advisor installer NOTE: Follow these steps to deploy applications and drivers. Right-click the Applications folder in the MDT 2013 Deployment Share, and select New Folder 5
Create a folder: Workstation Applications; right-click the new folder, and select New Application Select the radio button, Application with source files Enter the details for the application, and click Next 6
Browse to the location of the HP Performance Advisor installer At the command prompt, enter the command for silent install: msiexec /i Advisor.msi /passive Complete the wizard Repeat this process for HP RGS using the command line options: HP RGS (versions later than 7.1.0): Sender: SenderSetup.exe /z /autoinstall /agreetolicense /clipboard /usb /noreboot Receiver: ReceiverSetup.exe /z /autoinstall /agreetolicense /clipboard /usb=localremote /noreboot Create the HP Z240 Workstation-specific selection driver profile Expand the Advanced Configuration folder in the MDT 2013 Deployment Workbench Right-click the Selection Profiles folder, and select New Selection Profile 7
Name the selection profile: Z240 Windows10 64-bit Drivers Select Z240 Windows 10 64-bit Drivers from the Out-of-Box Drivers section Complete the wizard Import Windows 10 64-bit media NOTE: Skip this step if you already imported the media. Right-click the Operating Systems folder in the MDT 2013 Deployment Share, and select New Folder Name the folder something easily identifiable (in this example, Windows 10 64-bit), and click Next Insert the Windows 10 64-bit install media or mount the ISO file Right-click the Windows 10 64-bit folder, and select Import Operating System 8
Select Full set of source files Browse to either the mounted ISO file or the media that contains the Windows 10 64-bit install Complete the wizard Create an HP Z240 Workstation specific task Right-click the Task Sequences folder, and select New Folder Name the folder: Z240 Windows 10 64-bit; right-click this new folder, and select New Task Sequence Assign a Task Sequence ID, Name (in this case, Z240 Windows 10 64-Bit), and any important task sequence comments, then click Next Select Standard Client Task Sequence, and click Next Select the Windows 10 64-bit Install media imported earlier Complete the rest of the wizard Double-click the new task you created 9
Select the Task Sequence tab Expand the Preinstall folder, and select the Inject Drivers portion of the task Choose the Z240 Windows 10 64-bit selection profile from the dropdown Click the radio button Install only matching drivers from the selection profile Select the Options tab Click Add and select If statement 10
Click the radio button Any conditions, and click OK Click If any conditions are true statement, and click Add and select Task Sequence Variable Complete the Task Sequence Variable fields Variable: product Condition: equals Value: Hex ID of one of the HP Z240 workstations NOTE: To find the system ID for your workstation, run Get-WmiObject win32_baseboard from Windows PowerShell. HP Z240 Tower Workstation: 802F HP Z240 Small Form Factor Workstation: 802E 11
When finished, your options tab should appear as: Click Apply Expand the state restore section of the task Select the Custom Tasks folder Click Add, select Roles, select Install Roles and Features 12
Select the Install Roles and Features task, and select Windows 10 from the dropdown menu Click the checkbox.net Framework 3.5 Click Apply Click Add, select General, select Install Application 13
Click the radio button Install a single application Browse and select HP Performance Advisor Repeat this process for the HP RGS (NOTE: you must reboot the system before using HP RGS for your task) Click Add, select General, and Restart computer to add a reboot to the task Add any additional applications your task requires Click OK to close the task sequence NOTE: For a system with a native primary NVMe drive and at least one additional SATA drive, you must follow these additional steps. Use the chart below to determine the desired drive number. Hard drive number SATA 0 0 SATA 1 1 SATA 2 2 SATA 3 3 NVMe 0 +1 MDT disk value Example: For a system with a single SATA hard drive and a native NVMe, the desired drive number is 1. A single NVMe drive with no SATA drives is drive 0. 14
NOTE: For complex drive configurations where the system has a combination of SATA, native NVMe, and PCIe NVMe (such as HP Z Turbo Drive), test your deployment to guarantee that Windows installs on the desired drive, or remove all data drives. Expand the Install folder Select Install Operating System Complete the Operating system to install Select Specific Disk and partition from the location dropdown menu Select Disk X (calculated above) and Partition 2 Click Apply 15
Deployment Options Deploy via MDT standalone USB media (NOTE: To deploy using LiteTouch installation, skip to page 23.) Right-click the Selection Profiles folder in the Advanced Configuration section of the deployment workbench, and select New Selection Profile Name the selection profile: Z240 Windows 10 64-bit Media Select the Workstations Application folder Select the Windows 10 64-Bit operating system folder Select the Z240_Windows 10 64-Bit drivers folder Select the Z240_Windows 10 64-Bit Task Sequences folder Click Next and finish the wizard 16
Update the Deployment Share Right-click the main deployment share folder, and select Update Deployment Share Use the wizard to generate the boot images Right-click the Media folder in the Advanced Configuration section of the MDT 2013 Deployment Workbench, and select New Media Create a new folder to store the Z240 Windows 10 64-bit Media 17
In the Selection profile dropdown menu select Z240 Windows10 64-Bit Click Next and finish the wizard Right-click the media item you created, and select Properties (NOTE: If this was the first media created in MDT, it is MEDIA001) 18
Deselect the checkboxes Generate x86 boot image and Generate a Lite Touch bootable ISO image Select the Windows PE tab located at the top of the window From the Platform dropdown menu, select x64 Select the Features tab 19
Select the checkboxes for.net framework, Windows PowerShell, and Secure Boot Cmdlets (NOTE: Microsoft Data Access Components (MDAC/ADO) support is selected by default, and should remain selected.) Click Apply Select the Drivers and Patches tab From the Selection profile dropdown menu, select Z240 Windows 10 64-Bit 20
Select the radio button Include all drivers from the selection profile Click Apply Click OK Right-click the main Deployment Share folder, and select Update deployment share Right-click the Media item and select Update Media Content 21
Format and make a USB flash drive bootable Insert a USB flash drive into your computer Run the Deployment and Imaging Tools Environment as Administrator Enter Diskpart at the command prompt Run the Diskpart commands: List disk Select disk (your USB drive) Clean Create Partition Primary Format FS=Fat32 quick active assign exit Copy the MDT Standalone Media to the USB flash drive Open the media folder you created when generating the MDT standalone media Drill into the content folder Select all and copy it to your bootable USB flash drive Boot the Z240 using the USB flash drive Connect the USB flash drive to the system Boot the HP Z240, click the F9 key, and select the USB flash drive 22
To install using UEFI (Unified Extensible Firmware Interface), click the F9 key during BIOS POST, and select UEFI Boot Sources -> the USB drive containing the OS media. UEFI requires a new partitioning method referred to as GPT. (View the Windows and GPT FAQ for more details.) To install using MBR (Master Boot Record), click the F9 key during BIOS POST, and select Legacy Boot Sources -> the USB drive containing the OS media. Deploy via USB Discovery Media To deploy via a network connection, create USB boot media that will load from the network deployment share. Format and make a USB disk bootable Insert a USB flash drive Run the Deployment and Imaging Tools Environment as Administrator Enter Diskpart at the command prompt Run the Diskpart commands: List Disk Select disk (indicate your USB disk here) Clean (select your USB drive) Create Partition Primary Format FS=Fat32 quick active assign exit Mount the LiteTouchPE_x64.iso file Browse to the Boot folder in the root of your deployment share Right-click the LiteTouchPE_x64.iso file, and select mount (if not using Windows Server 2012, locate a utility to mount this file--try Microsoft Virtual CDROM Control Panel) Copy the contents of the ISO to the USB flash drive Copy the contents of the mounted ISO to the previously formatted USB flash drive Eject the USB flash drive 23
Boot the HP Z240 to the standalone USB Media Connect the USB flash drive to the system Boot the HP Z240, click the F9 key, and select the USB flash drive To install using UEFI, click the F9 key during BIOS POST, and select UEFI Boot Sources -> the USB drive containing the OS media. UEFI requires a new partitioning method referred to as GPT. (See Windows and GPT FAQ for more details.) Make sure to change the Format and Partition Disk section of editing the task sequence above. Install using MBR (Master Boot Record) To install using an MBR partition, click the F9 key during BIOS POST, and select Legacy Boot Sources -> The USB drive contains the OS media. Appendix: Additional HP support URLs HP Z Workstations HP Customer Support HP Driver Packs HP driver subscriptions, alerts, and notifications Download SoftPaqs Get connected hp.com/go/getconnected Copyright 2017 HP Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft and Windows are U.S. registered trademarks of the Microsoft group of companies. All other trademarks are the property of their respective owners. 4AA7-0407ENW, Created June 2017