Installation Instructions Model PAL- Parallel Printer Operation The model PAL- from Siemens Industry, Inc. allows the connection of an ITE Centronics parallel printer to the Siemens FireFinder- XLS, MXL, FireFinder-CC, FC0, FC00, FC9, FC9, Desigo CC and Cerberus DMS systems. See the manufacturer's installation manual for self diagnostics. The PAL- printer can be used with control panel models XLS, FC0, FC00, FC9, FC9, CC, Desigo CC, and Cerberus DMS Management Systems in UL8 and ULC-S7 installations. The PAL- Figure PAL- Printer printer can be used in UL7 installations, Control and Communication Units for Mass otification. For supplementary use only, the CC and PAL- may be connected to the UL07 approved XLS and MXL control panels. Installation UPS Standby Power The PAL- printer requires a standby power source in the event of the loss of primary input power (AC mains). Refer to Figure for the connection of a UPS to meet this requirement. TO TRI-0/B/S OR TRI-S/-D/-R IPUT TERMIALS. PROGRAM AS ORMALLY OPE TROUBLE CAUSIG IPUT I CSG-M (AccuLIK) OR ZEUS AD FPI- OR DPU, AS APPLICABLE. REFER TO TRI-0 ISTALLATIO ISTRUCTIOS, P/ -099, TE TRI-B ISTALLATIO ISTRUCTIOS, P/ -09, OR TE TRI-S ISTALLATIO ISTRUCTIOS, P/ -09 OR -098, OR TE TRI-S/-D/-R ISTALLATIO ISTRUCTIOS, P/ -000 OR -0907, AS APPLICABLE. UTILITY POWER SOURCE DO OT USE POWER TO PRITER SEE OTE DO OT USE TERMIAL BLOCK LOCATED O UPS SYSTEM COTROL BOARD O C AC IPUT FAIL C. All wires AWG min, 00V insulation. O C C BATTERY FAIL GD UTILITY IPUT IPUT POWER POWER AFTER FILTER 7 GD 8 9 OUTPUT OF TE UPS. Wiring to the printer and must be AWG min., 00V insulation in conduit, and located in the same room as the control panel.. Use the UPS ICS Lifeline Model 90007.. Standby Power requirements:, A for hours. 0 GD Siemens Industry, Inc. 8 Fernwood Road Florham Park, ew Jersey 079 P/ -0908- Figure UPS Wiring Diagram Siemens Canada Limited Kenview Boulevard Brampton, Ontario LT E Canada
SPP FireFinder-XLS System. The FireFinder-XLS system requires a Siemens model RPM module to interface to a Centronics parallel printer. When an RPM is used in conjunction with PAL-, the FireFinder-XLS system provides a supervised logging printer meeting the requirements of an FPA 7 Proprietary or UL07 Security system. The printer is supervised for paper out, AC loss, and printer parallel cable removal.. Refer to the RPM Installation Instructions, P/ -070, for more details on connecting and programming a RPM module.. Figure shows the proper installation of PAL- with an RPM module. PAL- or ITE LISTED PRITER 0 z. CETROICS CABLE SUPPLIED WIT RPM SUPERVISED POWER LIMITED RPM. The maximum distance from the RPM to the PAL- is feet. The two modules must be in the same room. Wiring to the printer must be AWG min., 00V insulation in conduit, and located in the same room as the control panel.. For FPA 7 Local, Auxiliary and Remote Station configurations, connect the output of the RPM to any UL ITE listed printer.. The printer must support the EPSO FX command set.. The printer is supervised for paper out, AC loss, and printer parallel cable removal by the RPM. A. For the Panasonic printer: After loading the paper in the PAL- printer, turn off the power and follow the steps below. a. While pressing the LOAD PARK button, turn on the power to the PAL- printer. Keep pressing the LOAD PARK button for seconds. b. Release the LOAD PARK button. c. The current setting will print. d. When printing is completed, the O LIE indicator will be lit. If the O LIE indicator is not lit, press the O LIE button. B. For the Epson LQ090 printer: Follow the steps below to enter default-setting mode. If single-sheet paper is loaded, you'll need to load a new sheet each time the printer ejects a printed page. OTE: For Auto line feed, the default-setting must be On as described in Step e. a. Make sure the printer is on and paper is loaded. Then press the Menu buttons (Item and Set) until the printer beeps and both the Menu lights turn on. The printer enters default-setting mode and prints a line showing which language is currently selected for printing the instructions. OTE: If the printer does not access default-setting mode, the printer is in lock-out mode. When the lock-out mode is on, the Pause and Paper Out lights flash simultaneously when the locked buttons are pushed. Follow the procedure for turning off the lock-out mode on page. b. If you want a different language, press the Item button until the printout shows the language you want underlined. c. Press the Set button to accept the language. The printer prints a line asking if you want to print all the current settings. d. To print a list of all the current settings, press the Set button. The printer prints all the settings and then the first setting again. To go through the settings one at a time, press the Item or Item button. The printer prints the first setting and its current value. e. Press the Set button to scroll through the options until you see Auto line feed. Press the Item or Item button to select On. Figure FireFinder-XLS System
f. Press the Set button to scroll through the remaining options for the selected setting until you see the one you want. Press the Item or Item button to select the next or previous setting you want to change. g. Repeat Step f for any other settings you want to change. h. When you finish, press the Menu buttons (Item and Set) again to exit default-setting mode. Your new settings become the printer's defaults. Turning Off the Lock-Out Mode: You can turn off the lock-out mode easily by using buttons on the control panel. Follow the steps below to turn off the lock-out mode. a. Make sure the printer is turned off. OTE: Whenever you turn off the printer, wait at least seconds before turning it back on; otherwise, you may damage the printer. b. Press and hold both the Load/Eject and Pause buttons. While these buttons are pressed, turn the printer on and the printer will beep once, indicating that the default-setting menu is unlocked. To turn on the lock-out mode, repeat steps a and b. The printer beeps twice, indicating that the lock-out mode has been turned on. MXL System. Installation of the PAL- in an MXL system requires that a Siemens model A- or A- is installed in the system. The A- and A- come installed in an MKB- or MKB- respectively. An A- is also included in model RCC-.. Refer to the MKB-/-C Installation Instructions, P/ -0877, the MKB-/-C Installation Instructions, P/ -087, and the RCC-/-R/-C/-FC/-FR Installation Instructions, P/ -08, for more details on connecting and programming MKB-, MKB- and RCC- modules respectively to a PAL- printer.. Figure shows the proper installation of a PAL- with an MXL system. 0 z PAL- PRITER (REAR VIEW) PRITER MKB- MKB- PORT CABLE SUPPLIED WIT PAL- OT SUPERVISED. Connect the PAL- printer to parallel port on the side of A- or A-.. PAL- printer is supervised for paper out, AC loss, and printer parallel cable removal by the CSG-M software at the computer.. Supervision for the MKB-/-C and MKB-/-C printer is set in CSG-M. In the etwork Module Map, select the MKB and press Enter. Scroll down to Printer Option and press Enter to toggle to the correct printer. The fields Supervised Operation and Serial Port must both be set to YES.. All cables must be in rigid conduit and cannot leave the room.. All circuits, except AC Input, are power limited. Figure MXL System
SPP FC0, FC00, FC9 or FC9. Installation of the PAL- in a FC0, FC00, FC9 or FC9 system requires that an FCA08-U is already installed.. Refer to the FCA08-U Installation Instructions, P/ AV00, for more details on connecting and programming an FCA08-U to a PAL-.. Figure shows the proper installation of a PAL- with a FC0, FC00, FC9 or FC9 system. PAL- or ITE LISTED PRITER 0 z. CETROICS CABLE SUPPLIED WIT FCA08-U SUPERVISED POWER LIMITED FCA08-U. The maximum distance from the FCA08-U to the PAL- is feet. The two modules must be in the same room. Wiring to the printer must be AWG min., 00V insulation in conduit, and located in the same room as the control panel.. For FPA 7 Local, Auxiliary and Remote Station configurations, connect the output of the FCA08-U to any UL ITE listed printer.. The printer must support the EPSO FX command set.. For FPA 7 Proprietary of UL 07 configurations, use printer Siemens Model PAL-, a UL listed for fire Centronics parallel printer.. The printer is supervised for paper out, AC loss, and printer parallel cable removal by the FCA08-U.. After loading the paper in the PAL- printer, turn off the power and follow the steps below. a. While pressing the LOAD PARK button, turn on the power to the PAL- printer. Keep pressing the LOAD PARK button for seconds. b. Release the LOAD PARK button. c. The current setting will print. d. When printing is completed, the O LIE indicator will be lit. If the O LIE indicator is not lit, press the O LIE button. Figure FC0, FC00, FC9, or FC9
Siemens Building Management System (CCXP-G or -GL, CCI7-G or -GL, Desigo CC, and Cerberus DMS). The PAL- can be used as a supervised journaling or logging printer when connected to a UL listed Siemens Building Management System computer to meet the requirements of an FPA 7 proprietary system. The printer is supervised for paper out, AC loss, and printer parallel cable removal.. Refer to the FireFinder-CC Operation, Installation and Maintenance Manual, P/ -0979, or Desigo CC Engineering Guide, Document ID AV0770, or Cerberus PRO Engineering Guide, Document ID AV070, for more details on connecting and programming the PAL-.. Figure shows the proper installation of PAL- with a CCXP-G or -GL, CCI7-G or -GL computer, Desigo CC or Cerberus DMS. LCD Monitor (rear view) See ote Parallel Printer (rear view) AC Main 0z V A Power Supply DCV TOUC VGA VIDEO /0 z Junction Box and Cover (user supplied) See otes and Approved Flexible Conduit Connector (user supplied) Bushing (user supplied) Approved / Flexible Metallic/onmetallic Conduit (user supplied) Power Connection Box (not required for Rack Mount or Console Installations) AC Main 0z Flexible Conduit (User Supplied) Conduit Junction Box (user supplied) Computer (rear view) CC-F COM * CC-F COM ot Supervised SOUD CARD COM COM SERIAL PORTS LPT PORT Keyboard & Mouse (Using Splitter Cable) USB PORTS LA LA CPU CARD See CC-F Installation Instructions, P/ -090 (Default COM Post Assignment Shown) Video LPT 7 8 (For CC Key) MOITOR CARD. Figure Siemens Building Management System. Connect the PAL- printer to LPT port on the rear of the Siemens Building Management system computer.. FPA 7 Proprietary and Local System installation requires that the computer, monitor and printer be UL rated for fire (Siemens models SCDXP/XPWA-B, SCDXP/XPWA-BT, SCD-9L-, SCD-9TL-, UW- W77-00T-M, UW-W77-00L-M, UW-W7AO-T-C, UW-W7AO-9T-C, UW-W7X-00T-M, UW- W7X-00L-M, UW-0000-T-L, UW-0000-T-L, UW-0000-L-L, UW-0000-L-L and PAL- respectively).. PAL- printer is supervised for paper out, AC loss, and printer parallel cable removal by the build management software at the computer.. All circuits, except AC Input, are power limited.. All cables must be in rigid conduit and cannot leave the room. Electrical Ratings, 0 Z, A.
This page is intentionally blank. Siemens Industry, Inc. 8 Fernwood Road Florham Park, ew Jersey 079 Siemens Canada Limited Kenview Boulevard Brampton, Ontario LT E Canada P/ -0908- Document ID AV070