NBT EVO GPS Receiver (with Nav/Voice and Video in Motion activation) Rev 1.2 BEFORE YOU START READ THE COMPLETE INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION IF YOU HAVE ANY QUESTIONS ABOUT THE USE OF THIS DEVICE, CONTACT YOUR BIMMER RETROFIT REPRESENTATIVE BEFORE USE Installation of NBT Evo GPS Receiver should be performed by an installer with appropriate knowledge and experience. We strongly recommend using services of professional installers, experienced with BMWs, for this installation. Battery should be disconnected prior to the installation for safety reasons. Reconnection of the battery should be done only after all electrical connections are in place. This manual covers installation of the NBT Evo GPS Receiver of two types: PNP and non-pnp versions.
Contents DEVICE OVERVIEW... 3 INSTALLATION OF NBT Evo GPS MODULE... 4 IS CODING REQUIRED IN YOUR CASE?... 8 FIRMWARE UPDATE MODE FOR GPS MODULE... 11 MANUAL FIRMWARE UPDATE MODE FOR THE GPS MODULE... 12
DEVICE OVERVIEW NBT Evo GPS Receiver with PNP cables NBT Evo GPS Receiver with non-pnp cables NBT Evo GPS Receiver with PNP harness Non-PNP harness for NBT Evo GPS Receiver
INSTALLATION OF NBT Evo GPS MODULE STEP 1 Remove NBT Evo head unit ( head unit ) from its position (but do not disconnect any of the wiring just yet). This will require you to remove some plastic trim on your dashboard and unscrew appropriate screws. Depending on the model of your BMW, you may need to switch transmission to Drive position, before removing the head unit (to give more space to maneuver). We also recommend that you place some protective blanket on the center console trim, to avoid possible scratches and dents. PNP Harness version installation steps (for all BMW F series) (skip to non-pnp harness version installation below if your version is non-pnp) STEP 2 1. Locate the main quadlock harness at the back of the head unit, as shown on the picture. Note that the colors of the wires connected to the harness may vary from one vehicle to another. Headunit in picture is shown for reference only.
2. Disconnect the quad lock connector from head unit and take a quick look at it. You will need a flat screwdriver in order to remove the MOST optical connector from the quadlock connector harness and re-plug it into the quadlock connector of the GPS module PNP harness. WARNING! It is important to reconnect this MOST optical cable in order to avoid loss of sound and other multimedia features. 3. Gently pull the plastic lock on the connector using a screwdriver and pull up the two optical cables. 4. Now re-plug this optical connector into the same position of the GPS PNP quadlock harness.
5. Connect the Main quadlock connector harness into the opposite end of the GPS PNP quadlock harness. STEP 3 Connect 12pin connector from PNP wiring harness to the GPS Receiver module. Make sure that connector plug is fully inserted in to the 12 pin connector at the GPS Receiver module. Non-PNP Harness version installation steps (whenever PNP harness does not fit) (skip this to STEP5 if your module is PNP) Non-PNP wiring is used when there is no way to fit PNP harness due to other PNP harnesses already installed between vehicle quadlock and headunit. For example in E series vehicles where PNP Plug version of enbt adapter is already installed.
STEP 4 Connect wires from non-pnp harness of GPS Receiver pin 1 to GND and pin2 to +12V supply. Connect wires from non-pnp harness of GPS Receiver pin 3 to CAN Low and pin 4 to CAN High lines. You may use wires at vehicle side quadlock connector: pin 12 for GND and pin 15 for +12V, pin 9 for CAN Low and pin 11 for CAN High. Make sure that wires are properly connected and isolated. It is recommended to secure wires to each other with tie-ups. Warning! GPS Receiver module may be configured for CAN 100kbit or CAN 500kbit speeds. When connecting CAN lines from non-pnp harness make sure to connect to appropriate CAN speed lines. For all E series BMWs when connecting to vehicle side quadlock connector make sure that GPS Receiver configured for CAN bus 100kbit speed. If connecting CAN lines to enbt adapter CAN2 side (headunit side) make sure that GPS Receiver configured for CAN bus 500kbit speed. STEP 5 Secure GPS Receiver module behind the dash with use of tie-ups or other type of mounting. Ensure that GPS Receiver module is secured and wiring attached to it is not blocking head unit path in the dash board. Normally at the back of the head unit tunnel in the dash board on the right or left side, there will be some opening. You may use that opening to install the GPS Receiver. This will let you install head unit properly to the end of the tunnel.
STEP 6 Connect OABR connector to NBT Evo OABR port. STEP 7 (RE-INSTALLING THE HEAD UNIT) Re-install your head unit inside the dash board. Follow the procedure which was used to remove headunit initially from the dash board. Warning! Avoid installing GPS Receiver module in direct contact with hot surfaces (head unit, vehicle heater, etc) because excessive heat may damage GPS Receiver. IS CODING REQUIRED IN YOUR CASE? If your GPS Receiver module is purchased together with the NBT Evo kit, its functionality should already be coded by BIMMER RETROFIT into the headunit. There is no need for additional coding, unless otherwise is stated by seller.
In case if your GPS Receiver retrofit adapter is purchased separately, there might be some coding required to have GPS feature working with NBT Evo. Please note that Evo headunit should be coded to your vehicle options list for proper functionality. The following two options must be coded in NBT Evo to switch it to external GPS mode: TELEMATIC_ECU: atm SYSTEM_GPS_RECEIVER: nicht_aktiv PNP Module Utility installation and use 1. PC utility and driver can be used with Windows7, Windows8 or Windows10. 2. Installation of.net Framework 4.5 is required for proper operation of the utility. 3. Connect USB cable from GPS Receiver module to PC. 4. Install attached with the pack driver for the newly apeard USB device. For Windows 10 driver installation is not required as the driver will be installed automatically. 5. In your PC new Serial Port device under Ports will apear. Write down number of the COM port device which apeared in your system 6. Start utility program included in the pack. 1. Select COM port of GPS Receiver module which apeared in your system and click Connect button.
2. Utility should report about sucesfull connection and Connect button should become green. 3. Click Read Settngs button to see current adapter settings. 4. When you need to disconnect from the adapter click Online/Connect button again. Utility will disconnect from the adapter. 5. Button Factory Deafults will place adapter in Factory defaults mode. 6. Button Clear will clean up display of the utility. 7. Under Options selection drop down list you may select various options. Button Run Task will run selected task. 8. Options selection tasks: Firmware Update mode switch adapter to firmware update mode Read Current settings reads current adapter settings and show them on display Reset factory defaults Reset module to factory defaults CAN Speeds sets CAN speeds for adapter operation. User may change depends on installation type. There are maybe some other options and modes which are not supported by GPS Receiver since this PNP utility is a universal between few products.
FIRMWARE UPDATE MODE FOR GPS RECEIVER MODULE It is not supported on Mac computers yet. Sorry Mac owners, you have to use Windows PC for this update. Remove your headunit and get access to the GPS Receiver Module. Disconnect adapter from headunit or from vehicle wiring. Plug micro USB cable into the slot on the adapter. Whenever firmware update procedure is required please follow the following steps: 1. Connect to PNP Utility as described above in the manual using USB cable. 2. Select from drop down menu Firmware Update mode and press Run Task button 3. Make sure that you have received new firmware update file from manufacturer. 4. Open File Explorer. You will see that new disk drive appeared in the system. 5. Open newly appeared drive. You will see there is a file: firmware.bin 6. Delete this file from the drive. 7. Copy new firmware update file from your computer to the newly appeared disk drive. You should have only one! file on this drive now. Firmware update file may have a name
different from firmware.bin Usually firmware update file has a name which includes firmware version, however the file extension should be.bin. There is no need to rename new firmware update file back to firmware.bin It is important not to interrupt process of file copying during the firmware update. Also it is important to make sure that you copied the correct firmware update file, received from the manufacturer to your GPS Receiver module. You should copy to GPS Receiver module only firmware update file and not any other files. MANUAL FIRMWARE UPDATE MODE FOR THE GPS RECEIVER MODULE If for any reason your firmware update is not successful using the method above and your module can no longer enter the firmware update mode, you can use the Manual firmware update method described below. For the firmware update of the GPS Receiver Module you will need to have the following: 1. Micro USB to USB adapter cable 2. Standard pen or pencil 3. Computer with at least one USB port available and Windows system installed In order to perform the firmware update, following the steps: 1. Disconnect and remove GPS Receiver module from your vehicle. 2. Plug USB cable to your GPS Receiver Module. There is a small Micro USB connector on the side of the module.
3. Take a pen or pencil and use it to gently press a small button located on the side of the GPS Receiver Module, in the hole. This hole usually located next to the USB port depends on the module type and construction. Please do not push hard as it may damage the button. 4. While holding the button down, connect another end of the USB cable to your PC s USB port. 5. After short time (up to 10 seconds) you will see that new drive (G:) appeared under My Computer. This drive will have a name: CRP1 ENABLE. 6. Immediately release button as soon as you see drive appeared under My Computer. In your case it will most probably have a different letter (D:, E:, F:, etc.)
6. Newly appeared drive will contain a single file called: firmware.bin 7. Delete this file (firmware.bin) completely from the drive. 8. Copy new software update file which you received from us onto the drive G: 9. Once the file is copied disconnect USB cable from your computer. 10. Disconnect USB cable from GPS Receiver module and install module back to your vehicle. 11. Software update is now completed. Accessing service menu in NBT Evo to verify GPS functionality There is a hidden service engineering menu in NBT Evo headunit which provides some technical information useful for verification of the system functionality. In case if it is required to see current GPS status, visible satellites, GPS position lock, etc, you may access this service menu. Follow the steps below: 1. Press MENU button once to make sure that you are in main menu 2. Push and hold idrive controller for 10 seconds in Up forward position then release 3. Slowly rotate idrive controller knob exactly 3 clicks clockwise 4. Slowly rotate idrive controller knob exactly 3 clicks counterclockwise 5. Rotate idrive controller 1 click clockwise 6. Rotate idrive controller 1 click counterclockwise 7. Rotate idrive controller 1 click clockwise 8. Push idrive knob down and release it immediately 9. Headunit should stay in main menu, this indicates that steps 1-9 correctly done. If menu opened you have to repeat steps 1-9. 10. Open My Vehicle menu
11. Go to the very bottom and open *Service menu* 12. Go to Navigation menu and then open GPS menu. 13. Open GPS Status menu and see GPS Status message GPS Status: Check Antenna GPS Module is searching for satellites. GPS is not locked. Check your antenna, make sure it is connected to GPS Receiver. You should be outside with good sky visibility to get 3D lock. GPS Status: 3D Fix GPS Module found satellites and now has proper 3D locked position For all questions or other inquires please contact us at: info@bimmerretrofit.com or visit: www.bimmerretrofit.com Copyrighted 2010-2018 Bimmer Retrofit Company. All rights reserved.