SUPERTALENT DURA DRIVE ZT4 DATASHEET 1.8 IDE/PATA ZIF SOLID STATE DRIVE Copyright, Property of Super Talent Technology. All rights reserved. The information and specification provided in this document should be used for comparative analysis and reference purposes. The contents of this document are subject to change without prior notice. Rev 1.0 Oct 2014 Page 1
TABLE OF CONTENTS Table of Figures... 3 Table of Tables... 3 1.0 Product Description... 4 1.1 Product Overview... 4 1.2 Target Applications... 4 1.3 Product Features... 4 1.4 System Requirements... 5 2.0 Product Ordering Part Numbers... 5 2.1 Ordering Part Structure... 5 2.2 Valid Ordering Part Numbers... 5 3.0 Physical Specifications... 6 3.1 Mechanical Specifications... 6 4.0 Electrical Specifications... 6 4.1 Performance Specifications... 6 4.2 Absolute Maximum Ratings... 7 4.3 Power Consumption Test for Result... 7 5.0 Environmental Specifications... 8 6.0 Quality And Reliability Specifications... 8 7.0 Compliance Specifications... 9 8.0 Pin Descriptions... 9 8.1 Data Pin Assignments... 9 Rev 1.0 Oct 2014 Page 2
9.0 Supported ATA Commands... 10 9.1 Standard Commands... 10 10.0 Firmware Upgrade... 12 11.0 Installation... 12 11.1 Before Getting Started... 12 11.2 Installation... 12 11.3 Using the SSD... 13 For More Information... 14 Change Record... 14 TABLE OF FIGURES Figure 1: Outline Drawing... 6 TABLE OF TABLES Table 1: Ordering Part Structure... 5 Table 2: Valid Ordering Part Numbers... 5 Table 3: Data Transfer Time Specifications... 7 Table 4: Absolute Maximum Ratings... 7 Table 5: Power Consumption Test for Result Table... 7 Table 6: Compatibility Test Configure... 8 Table 7: Data Pin Signal Assignment... 9 Table 8: Command Set... 10 Table 9: Set Features Register Values... 11 Table 10: Change Record... 14 Rev 1.0 Oct 2014 Page 3
1.0 PRODUCT DESCRIPTION 1.1 PRODUCT OVERVIEW A Solid State Disk (SSD) is a storage device that is based on semiconductors rather than rotating magnetic platters. Most SSDs, including Super Talent s offerings, are based on NAND Flash chips because they are fast, highly reliable, widely available and are non-volatile. SSDs are 100% compatible with standard hard disk drives, using both industry standard dimensions and a standard hard drive interface. While typical spinning HDDs are the weakest point when it comes to withstanding extremes, an SSD drive is an asset. Along with its durability and reliability, the SSD brings unparalleled performance. 1.2 TARGET APPLICATIONS Military and Aerospace Enterprise Computing Embedded / Industrial Systems Notebook Medical Industry Casino Gaming 1.3 PRODUCT FEATURES Capacity: 16GB to 256GB Form Factor: 1.8 ZIF (51.8mm x 69.8mm x 5.0mm) IDE Interface: PIO Mode 0-6, MDMA Mode 0-4, and UDMA Mode 0-7 SMART feature set and 48-bit Address feature set Compatibility: Full IDE hard disk compatible Ultra rugged and reliable High-speed performance Silent, no moving parts Data retention: JESD47 compliant Proprietary wear leveling algorithms Proprietary design connector 100% tested hardware and software Support Industrial Temperature Rev 1.0 Oct 2014 Page 4
1.4 SYSTEM REQUIREMENTS Operating Voltage Requirement: V cc = 3.3V +/-5% Operating System: Supported by all Operating Systems Interface: 40Pin IDE (PATA) ZIF interface Installation Requirements: System Mounting Hardware 40pin ZIF Cable 2.0 PRODUCT ORDERING PART NUMBERS 2.1 ORDERING PART STRUCTURE Table 1: Ordering Part Structure Catalog X Product Type XX Density XXX Technology XX Form & Case Factor XX F Channel EU IDE 1.8 MLC 016 16GB MD SM2236AC 1X 1.8 ZIF 5.0mm 032 32GB 064 64GB 128 128GB 256 256GB 2.2 VALID ORDERING PART NUMBERS Table 2: Valid Ordering Part Numbers Product Family Capacity Flash Form Factor Casing Channel/Retail Part Number 16GB MLC 1.8 Metal/Plastic FEU016MD1X 32GB MLC 1.8 Metal/Plastic FEU032MD1X Dura Drive 64GB MLC 1.8 Metal/Plastic FEU064MD1X ZT4 128GB MLC 1.8 Metal/Plastic FEU128MD1X 256GB MLC 1.8 Metal/Plastic FEU256MD1X Rev 1.0 Oct 2014 Page 5
3.0 PHYSICAL SPECIFICATIONS 3.1 MECHANICAL SPECIFICATIONS Length: 51.80 ± 0.25 mm Width: 69.80 ± 0.25 mm Thickness: 5.00 ± 0.25mm Figure 1: Outline Drawing 4.0 ELECTRICAL SPECIFICATIONS Operating Voltage: V cc = 3.3V +/-5% Capacity and Block Size Information Capacity: 16GB/32GB/64GB/128GB/256GB Sector Size: 512Bytes Modes: ATA-7 standard compliant, PIO Mode 0-6, MDMA Mode 0-4, UDMA Mode 0-7 4.1 PERFORMANCE SPECIFICATIONS Access Time: 0.1 ms Rev 1.0 Oct 2014 Page 6
Seek Time: 0 ms Power on to Ready: Depending on system HW and SW Mount Time: The mount time for initializing and mounting the Dura Drive ZT4 depends on the O/S and testing platform. Data Transfer Time: Table 3: Data Transfer Time Specifications Device Sequential Read Max (MB/Sec) Sequential Write Max (MB/Sec) FEU016MD1X 75 26 FEU032MD1X 110 45 FEU064MD1X 110 72 FEU128MD1X 112 90 FEU256MD1X 112 90 4.2 ABSOLUTE MAXIMUM RATINGS Table 4: Absolute Maximum Ratings Symbol Rating Value Unit V cc Power Supply Voltage -0.3 to 3.6 V V IN Input Voltage -0.5 to Vcc +0.5 V T STG Storage Temperature -55 to +115 C T OPR Operating Temperature(Commercial) 0 to +70 C T OPR Operating Temperature(Industrial) -40 to +85 C 4.3 POWER CONSUMPTION TEST FOR RESULT Table 5: Power Consumption Test for Result Table Test software: Crystal Disk Mark3.0 Times 1 2 3 Power(W=U*I) Static current(idle mode current) 150mA 150mA 150mA 3.3V *0.15A=0.495W Seq read 360mA 360mA 360mA 3.3V *0.36A=1.188W Seq write 360mA 360mA 360mA 3.3V *0.36A=1.188W 512K read 400mA 400mA 400mA 3.3V *0.40A=1.320W Dynamic current 512K write 360mA 360mA 360mA 3.3V *0.36A=1.188W (R/W mode 4K read 280mA 280mA 280mA 3.3V *0.28A=0.924W current) 4K write 360mA 360mA 360mA 3.3V *0.36A=1.188W 4K QD32 read 280mA 280mA 280mA 3.3V *0.28A=0.924W 4K QD32 write 360mA 360mA 360mA 3.3V *0.36A=1.188W Rev 1.0 Oct 2014 Page 7
5.0 ENVIRONMENTAL SPECIFICATIONS Operating Temperature Commercial Grade: 0 C to +70 C Industrial Grade: -40 C to +85 C Humidity: 5% to ~98% RH Operating Shock: 1500G Operating Vibration: 16G Operating Altitude: TBD 6.0 QUALITY AND RELIABILITY SPECIFICATIONS Data Retention: JESD47 compliant Wear Leveling: Patent pending wear leveling algorithms incorporated Bad Block Management: Failed Blocks of Flash will be replaced with new ones by the SSD. ECC/EDC (Error Correction Code/Error Detection Code): Built in error detection and correction will correct physical bit errors in NAND. Drives use BCH 72 bits ECC MTBF: >1,000,000 hours Power Cycle: 1000 times Table 6: Compatibility Test Configure Test Platform: Compatibility Test Configure Test Items Total Times PASS Times Fail Times Log Photo Cycles 1000 times 1000 times 0 times Reboot 1000 times 1000 times 0 times Rev 1.0 Oct 2014 Page 8
7.0 COMPLIANCE SPECIFICATIONS All Dura Drive ZT4 are compliant with the following standards and regulations: RoHS FCC CE 8.0 PIN DESCRIPTIONS 8.1 DATA PIN ASSIGNMENTS Table 7: Data Pin Signal Assignment Pin Signal Name Description Pin Signal Name Description 1 N/A Reserved 2 N/A Reserved 3 /RESET Reset 4 GND Return Current Path 5 HD7 Data 7 6 HD8 Data 8 7 HD6 Data 6 8 HD9 Data 9 9 HD5 Data 5 10 HD10 Data 10 11 HD4 Data 4 12 HD11 Data 11 13 HD3 Data 3 14 HD12 Data 12 15 HD2 Data 2 16 HD13 Data 13 17 HD1 Data 1 18 HD14 Data 14 19 HD0 Data 0 20 HD15 Data 15 21 GND Return Current Path 22 DMARQ DMA Request 23 GND Return Current Path 24 IOWR Write Strobe 25 IORD Read Strobe 26 GND Return Current Path 27 IORDY I/O Channel Ready 28 GND Return Current Path 29 DMACK Direct Memory Access Controller 30 INTRQ Interrupt Request 31 HA1 Address 1 32 PDIAG Passed Diagnostics 33 HA0 Address 0 34 HA2 Address 2 35 / CS0 (1F0-1F7) 36 /CS1 (3F6-3F7) 37 /DASP Dual purpose pin 38 VCC 3.3 Power (Source) 39 VCC 3.3 Power (Source) 40 N/A Reserved Rev 1.0 Oct 2014 Page 9
9.0 SUPPORTED ATA COMMANDS 9.1 STANDARD COMMANDS Dura Drive ZT4 supports the commands shown in the following tables. Table 8: Command Set Command Name Code (Hex) Protocol General Feature Set Execute Device Diagnostic 90h Device diagnostic Flush Cache E7h Non-data Identify Device ECh PIO data-in Read DMA C8h DMA Read Multiple C4h PIO data-in Read Sector(s) 20h or 21h PIO data-in Read Verify Sector(s) 40h or 41h Non-data Set Feature EFh Non-data Set Multiple Mode C6h Non-data Write DMA CAh DMA Write Multiple C5h PIO data-out Write Sector(s) 30h or 31h PIO data-out NOP 00h Non-data Read Buffer E4h PIO data-in Write Buffer E8h PIO data-out Set Feature EFh Non-data Power Management Feature Set Check Power Mode E5h or 98h Non-data Idle E3h or 97h Non-data Idle Immediate E1h or 95h Non-data Sleep E6h or 99h Non-data Standby E2h or 96h Non-data Standby Immediate E0h or 94h Non-data Security Mode Feature Set Security Set Password F1h PIO data-out Security Unlock F2h PIO data-out Security Erase Prepare F3h Non-data Security Erase Unit F4h PIO data-out Security Freeze Lock F5h Non-data Security Disable Password F6h PIO data-out SMART Feature Set SMART Disable Operations B0h Non-data Rev 1.0 Oct 2014 Page 10
Command Name Code (Hex) Protocol SMART Enable/Disable Autosave B0h Non-data SMART Enable Operations B0h Non-data SMART Return Status B0h Non-data SMART Execute OFF-LINE Immediate B0h Non-data SMART Read Data B0h PIO data-in SMART Read Threshold B0h PIO data-in SMART Save Attribute Values B0h Non-data Host Protected Area Feature Set Read Native Max Address F8h Non-data Set Max Address F9h Non-data Set Max Set Password F9h PIO data-out Set Max Lock F9h Non-data Set Max Freeze Lock F9h Non-data Set Max Unlock F9h PIO data-out 48-bit Address Feature Set Read Sector(s) Ext 24h PIO data-in Read DMA Ext 25h DMA Read Multiple Ext 29h PIO data-in Write Sector(s) Ext 34h PIO data-out Write DMA Ext 35h DMA Write Multiple Ext 39h PIO data-out Write DMA FUA Ext 3Dh DMA Read Verify Sector(s) Ext 42h Non-data Write Multiple FUA Ext CEh PIO data-out Flush Cache Ext EAh Non-data Others Format Track 50h PIO data-out Initialize Drive Parameters 91h Non-data Recalibrate 1Xh Non-data Seek 7Xh Non-data Wear Level F5h Non-data Write Verify 3Ch PIO data-out Table 9: Set Features Register Values Value Command Value Command D0h Read Data D5h Reserved D1h Read Attribute Threshold D6h Reserved D2h Enable/Disable Autosave D8h Enable SMART Operations D3h Save Attribute Values D9h Disable SMART Operations D4h Execute OFF-LINE Immediate DAh Return Status Rev 1.0 Oct 2014 Page 11
10.0 FIRMWARE UPGRADE The firmware cannot be upgraded by customers. Please contact a Super Talent account manager. 11.0 INSTALLATION 11.1 BEFORE GETTING STARTED BACK UP YOUR DATA Back up your Data VISUAL INSPECTION Before unpacking and handling the SSD, discharge the static electricity by touching the metal chassis of your computer or by using an anti-static wrist strap. Inspect the box and device for the following: Damaged or water-stained box Any damage to the SSD 11.2 INSTALLATION SYSTEM REQUIREMENTS Install the SSD in your computer; ensure that you have the following item: Mounting screws 40pin ZIF Cable VISUAL INSPECTION The SSD can be installed in any mounting position in your computer. INSTALL THE SSD Follow these steps to install the SSD Power down the PC Remove the computer system outside cover Installed the SSD Power on the system A BIOS sign-on message appears and displays a key sequence to enter the BIOS setup. Set up the BIOS to recognize the SSD. Rev 1.0 Oct 2014 Page 12
Installation complete 11.3 USING THE SSD HANDLING THE SSD Be cautious when unpacking, installing, and handling the SSD drive. Misuse of the SSD will void all warranty. Follow the succeeding instructions when managing the SSD Follow all ESD pre-cautions always operate the SSD within environmental conditions. Never switch DC power to the drive by plugging and Ensure correct interface polarity whenever plugged into the drive USING THE SSD IN A MS-DOS OS SSD is already partitioned and formatted by NTFS, so if customer want to install MS- DOS O/S in SSD, it should be re-partitioned and re-formatted. After installing the SSD, it must be installed as a disk drive under DOS. Run the DOS commands as listed below and follow the instructions displayed for each command. Run the DOS FDISK program to partition the SSD Verify that the partition is active and ready for formatting Run the DOS FORMAT command to high-level format the SSD USING THE SSD IN A WINDOWS O/S No modifications need to be made to use the SSD in a Windows O/S platform USING THE SSD IN A LINUX O/S No modifications need to be made to use the SSD in a Linux O/S platform USING THE SSD IN OTHER O/S No modifications need to be made to use the SSD in other O/S platforms Rev 1.0 Oct 2014 Page 13
FOR MORE INFORMATION For Technical Support: If additional support is needed, please visit the Super Talent Web site at www.supertalent.com for the following topics: Warranty Services: Includes the warranty service policy and the RMA request forms. Technical Information: Includes product data sheets and various USB whitepapers. Tools Section: Includes frequently asked questions (FAQs). For More Information or Further Technical Support Please Contact: Super Talent Technology 2077 North Capitol Avenue San Jose, CA 95132 USA Tel: +1 (408) 934-2560 Support: Support@supertalent.com Sales: Sales@supertalent.com OEM Sales: OEMSales@supertalent.com CHANGE RECORD Table 10: Change Record Version Release Date Changes 1.0 October 31st, 2014 Initial Release in new template Rev 1.0 Oct 2014 Page 14