Features 10/100Mbps Ethernet full duplex Auto Negotiation Support C++/C Modbus/TCP drivers and OPC server Support configuration via built-in Web browsing, (HTML), Device Finder and I/O configuration utilities Web server service and SNMP for I/O monitoring Instant event reporting by SNMP trap Built-in watchdog timer and real-time clock Configurable output power-on & safe status setting Built-in simple condition rules for I/O logic programming Peer-to-peer I/O over TCP/IP Easy-installation DIN-rail mounting Support SDK API library and sample program in C#, C++, VB and BCB :. Introduction Leader-5000 is a series of Ethernet-based block I/O modules for distributive monitoring and controls. The block I/O modules feature built-in RSIC-based processor with MAC, and capable of performing analog I/O, digital I/O, and temperature measurement in an Ethernet network with Modus/TCP protocol at LAN, intranet or Internet. Versatility Communication Network A Leader-5000 I/O module can simultaneously serve communication from different Ethernet socket ports. For example, HTTP, HAL Windows-based utility and Modbus/TCP Server. OPC server and various C++/C Modbus/TCP communication driver are provided for user to choose the easiest way to have the Leader-5000 block modular I/Os to go with his self developed software or HMI/SCADA package. :. Leader 5000 Appearance
:. System Features Model Name I/O System Software Communication Protocol CPU Programming Ethernet SDRAM Flash EEPROM Peer-to-Peer DIN-rail Mounting Remote Monitoring Network Server SDK Provided Utility OPC Server Driver Modbus/TCP Leader-5000 Series 8-bit, RISC-Based 100MHz Condition Logic Rule 1 x 10/100 Mbps, RJ-45 32 KB 512 KB 256 bytes YES YES Web Server Http, SNMP C/C++, C#, VB, BCB Block I/O Utility YES YES :. Block I/O Utility Quick to Use Windows Utility Block I/O Utility allows you to configure and monitor Leader-5000 Series Ethernet-Based I/O modules remotely. The Utility automatically scanning installed Leader-5000 Ethernet-Based Block I/O modules. With Block I/O utility, you can browse available units, view the status of each channel, configure the I/O settings and configure the active I/O logic rule and alarms. The General Page (LD-5000 Series) The I/O Status Page, it can monitor the current working status of each channel both on DI and DO and Peer to Peer I/O Active
Status The I/O Configuration Page, it can configure the DI/DO mode and check status for each channel. DI/ Event Counter channel configuration and test, power on settings, safe status settings. DO/ Pulse Output channel configuration and test, power on settings, safe status settings.
Condition Logic Rule The I/O logic rule provides one-time operation in each entry. The theory is the same as the IF-Then rule. It s easy to understand rules, no need to know extra program script to configure this. In Logic Rule #ID Configuration page, select Enable and configure the Condition and Actions then press Apply to enable the rule. When the Conditions is reached, the system automatically activates the Actives. The maximum I/O logic rules for Leader-5068 support are up to 7 rules. Each rule can support up to 4 different conditions and 4 different actions. The Alarm page, easy to configure the I/O logic rules, alarm message and peer to peer I/O activity. Support up to 4 different conditions and 4 different actions. SNMP Trap SNMP Trap Setting: Configure up to 3 SNMP Trap Server s IP in the LD-5068. SNMP Trap Setting: Configure up to 4 SNMP Trap Server s IP in the LD-5017/LD-5018/LD-5014/LD-5024. Peer to Peer Enable Peer to Peer I/O activity: Configure module s input channels mirrored to remote IP Configure module s output channels mirrored from remote IP
Ethernet-Based I/O Status via Web Browser Enter the IP address of the Ethernet-Based Block I/O Modules in Internet Explorer. Then you can access the embedded web browser of the I/O server. The web browser allows you monitor the information/status of each channels. Monitor the I/O status through any web browser. (The above sample is for LD-5068 digital I/O module) :. Dimensions
:. Specifications COMMON SPECIFICATIONS CPU: RISC-Based, 100MHz SDRAM: 32K bytes Flash: 512K bytes EEPROM: 256 bytes Watch Dog Timer: 1.0 sec H/W Network Protocols: Modbus/TCP, TCP/IP, UDP, SNMP, HTTP, TFTP, BOOTP, DHCP Ethernet: IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX Bus Connection: RJ-45 modular jack, Auto MDI/MDI-X Protection: 1.5 KV magnetic isolation protection Serial Interface: RS-232, 2m JTAG PIN Power Input Connector: 24VDC, 3-pin, 5mm pitch LED Indication: PWR: Power Input Green ON RDY: System Ready Red ON LAN Activity Orange ON/Blinking LAN Speed 100M/10M Green ON/OFF Mechanical: ABS with Standard DIN-rail mounting I/O Wiring Connector: 16-pin, 20-pin, 24-pin screw terminal, 5mm pitch Dimensions (W x H x D): 40 x 108 x 73.48mm Power Input Requirements: System Power: 24VDC nominal, 1.92W Field (I/O) Power: 24 VDC nominal, 15 to 32 VDC GENERAL ENVIRONMENT Operating temperature: 0 ~ 50 C Storage temperature: -20 ~ 70 C Humidity (Operating): 20 ~ 90% non-condensing SOFTWARE Network Server: Http, SNMP SDK Provided: C/C++, C#, VB, BCB Utility: Block I/O Utility OPC Server Driver: YES
Leader-5068 Ethernet-based 14-CH DI Isolated and 8-CH Isolated DO Module DIGITAL OUTPUT DIGITAL INPUT Input Channels: 14 Input Type: sink type Input Mode: D/I or event counting with input frequency of 100 Hz max. DC Input: 30V max. Threshold Voltage: 4V Responding Time to Host PC Request: <2ms Output Channels: 8 Output Type: source type Output Mode: Level or pulse output with programmable pulse width Working Range: 5-40VDC Driving Capacity: 150mA max. Responding Time to Host PC Request: <2ms Output Initial State: Programmable Isolation Voltage: 1500VAC POWER REQUIREMENT Power Consumption: 100mA @ 24VDC max. Field (I/O) Power: 24VDC nominal, 18 to 32 VDC Leader-5017 Ethernet-based 8-CH Isolated Analog Input Module ANALOG INPUT Channels: 8, differential Resolution: 16-bit Programmable Input Range: Supports Different Input Range for Different Channels Voltage: ±10V, ±5V, ±1V, ±500mV, ±150mV Current: ±20mA (Jumper Setting Enabled 125Ω Resistor) Accuracy: ±0.05% of FSR ±1LSB Sampling Rate: 10 samples/sec (total) Input Impedance: 10 MΩ Calibration: On Board EEPROM POWER REQUIREMENTS Power Consumption: 125mA @ 24VDC max.
Leader-5018 Ethernet-based 8-CH Isolated Thermocouple Input Module ANALOG INPUT (Voltage, Current and Thermocouple) Channels: 8, differential Resolution: 16-bit Input Type: Thermocouple (T/C), mv, V, ma Programmable Input Range: Supports Different Input Range for Different Channels Voltage: ±2.5V, ±1V, ±500mV, ±100mV, ±50mV, ±15mV Current: ±20mA (Jumper Setting Enabled 125Ω Resistor) Thermocouple: K/J/N/C/E/B/T/R/S T/C Type Range K -100 C ~ 1000 C J -100 C ~ 900 C N -270 C ~ 1300 C C 10 C ~ 2310 C E -240 C ~ 2310 C B 0 C ~ 1800 C T -270 C ~ 400 C R -50 C ~ 1530 C S -50 C ~ 1700 C Accuracy: ±0.1% of FSR ±1LSB Sampling Rate: 10 samples/sec (total) Input Impedance: 10 MΩ Calibration: On Board EEPROM POWER REQUIREMENTS Power Consumption: 130mA @ 24VDC max. Leader-5014 Ethernet-based 4-CH Isolated RTD Input Module RTD INPUT Channels: 4 RTD Resolution: 16-bit Input Type: Pt100 and Ni120 RTD Input Connections: 3, 4 or 5 wire Programmable RTD Input Range: Supports Different Input Range for Different Channels Pt100 (-100 C ~ 100 C α=0.00385) Pt100 (0 C ~ 100 C α=0.00385) Pt100 (0 C ~ 200 C α=0.00385) Pt100 (0 C ~ 600 C α=0.00385) Pt100 (-100 C ~ 100 C α=0.00392) Pt100 (0 C ~ 100 C α=0.00392) Pt100 (0 C ~ 200 C α=0.00392) Pt100 (0 C ~ 600 C α=0.00392) Nickel 120Ω (-80 C ~ 260 C α=0.00672) Accuracy: ±0.1% of FSR ±1LSB Sampling Rate: 10 samples/sec (total) Input Impedance: 10 MΩ Calibration: On Board EEPROM
POWER REQUIREMENTS Power Consumption: 125mA @ 24VDC max. Leader-5024 Ethernet-based 4-CH Isolated Analog Output Module ANALOG OUTPUT Channels: 4(voltage or current), differential Resolution: 12-bit Output Range: 0-20mA (sink), 0-10V, ±10V Output Impedance: 0.5Ω Current Load Resistor: 0 to 500Ω (source) Programmable Output Slope to Safety Value: 0.125 to 128 ma/sec (Current) 0.0625 to 64 V/sec (Voltage) Accuracy: ±0.1% of FSR ±1LSB Calibration: On Board EEPROM POWER REQUIREMENTS Power Consumption: 132mA @ 24VDC max. Order Information ETHERNET-BASED BLOCK I/O MODULES Leader-5068 Ethernet-based 14-CH Isolated DI and 8-CH Isolated DO Module Leader-5017 Ethernet-based 8-CH Isolated Analog Input Module Leader-5018 Ethernet-based 8-CH Isolated Thermocouple Input Module Leader-5014 Ethernet-based 4-CH Isolated RTD Input Module Leader-5024 Ethernet-based 4-CH Isolated Analog Output Module