Installation, operating and maintenance ADALINK II Web solution for LENNOX units supervision ADALINK II-IOM-1401-E lennoxemeia.com
CONTENT 1 INTRODUCTION 1.1 - ADALINK II system description... 3 2 INSTALLATION 2.1 - BUS wiring... 4 2.2 - CLIMATIC settings... 4 2.3 - ADALINK II web connection... 5 3 WEB APPLICATION 3.1 - Home Page... 6 3.2 - Unit page... 7 4 BUTTONS 4.1 - Top bar buttons... 8 4.2 - Bottom bar buttons... 10 4.3 - Time zones scheduling page... 11 4.4 - Alarms page... 14 4.5 - Graphical trends page... 15 4.6 - Access management... 16 ADALINK II-IOM-1401-E - 1 -
1. INTRODUCTION You must read and be familiarized with this instruction manual before the start-up of the ADALINK II. You must apply the following instructions. We lay stress on the importance of training for a proper use of the Adalink II. This instruction manual must stay close to the Adalink II Box. The Adalink II is a solution that enables the remote access to the Lennox units data, through Ethernet connection and simple web pages. The Adalink II can be connected up to 16 units and allows to: Show unit operation through animated images Adjust main setpoints of the unit (On/Off, cooling/heating setpoints, etc.) Program zone scheduling Show unit alarms log Show unit temperature trends Adalink II Web pages can be accessed through standard internet browser (like IE, Chrome, Firefox, etc.) with Java machine installed (available at www.java.com/download). ADALINK II-IOM-1401-E - 2 -
ADALINK II SYSTEM DESCRIPTION The Adalink II is provided inside a complete electrical box which requires only the following connections : 230Vac power supply RS485 communication bus Ethernet connection ADALINK II-IOM-1401-E - 3 -
2. INSTALLATION 2.1 - BUS WIRING The Adalink II must be connected to the Lennox units through the BMS communication bus as shown in the following picture (please refer to electrical drawing for further information). Daisy-chain connection is required (star and ring connections are forbidden). Shielded twisted pair is required (Lennox recommends the use of LiYCY-P cable). In case of bus lines length > 100m, 120Ω 1/4W resistance must be connected on the last unit between + & - connections. The length of the cable does not exceed 1000m. 2.2 - CLIMATIC SETTINGS A minimum software version RT50 v24.10 for CLIMATIC 50 and RT60 v3 r0.0 for CLIMATIC 60 is mandatory (last upgrade available is suggested). The following settings must be done on CLIMATIC controllers: Unit address: each unit must have a unique address o CLIMATIC 50: Menu 3931 = 1..16 o CLIMATIC 60: Menu 3181 = 1..16 BMS protocol selection: o CLIMATIC 50: Menu 3932=Adalink o CLIMATIC 60: Menu 3182=LennoxVision Baudrate selection: o CLIMATIC 50: Menu 3933=9600 o CLIMATIC 60: Menu 3183=9600 RS485 communication card must be installed on each CLIMATIC ADALINK II-IOM-1401-E - 4 -
2.3 - ADALINK II WEB CONNECTION To startup the Adalink II, you need to connect it to your PC via cross cable: To establish the connection between the PC and the Adalink II, you need to go on your computer control panel and the network configuration and set the IP address 192.168.12.250 as shown in the picture below. Once connected to the Adalink II web page, its IP address can be changed pressing the (administrator rights are requested to make this setting) button ADALINK II-IOM-1401-E - 5 -
3. WEB APPLICATION 3.1 - HOME PAGE This is the 1 st page to be displayed after entering the IP address of the AdalinkII in the browser. In the bottom-right bar the user level is displayed together with the Adalink II date and hour Top buttons bar Customizable background picture Installed units Customizable logo User access level Date & hour Configured units are displayed above the background image with an animated picture. The picture animation respects the following rules: unit running unit stopped unit in alarm unit offline Clicking on the unit icon, the unit page will be entered. NOTES To customize logo and background image, please contact LENNOX technicians. ADALINK II-IOM-1401-E - 6 -
3.2 - UNIT PAGE At the top-left corner, the unit label and address are displayed The main unit components are represented by animated icons The sensor readings are displayed in text boxes Only the elements actually present in the unit are displayed (e.g. humidty % is not displayed if the unit has no humidity option kit) The following variables can be edited CURRENT MODE SETPOINTS (window visible only to user-level>=user) General On/Off Room Cooling setpoint Room Heating setpoint Room Dehumidification setpoint Room Humidification setpoint Minimum fresh air setpoint (visible only to user-level>=admin) Blower nominal speed: (visible only to user-level>=admin) Blower dead zone enable: (visible only to user-level>=admin) ADALINK II-IOM-1401-E - 7 -
4. BUTTONS 4.1 - TOP BAR BUTTONS Placed at the top of the page, between the 2 logos. House button o displayed in all pages o this button moves to the home page (in this case it has no action) Log-in button o displayed in all pages when no user is logged-in (Visu mode) o Once pressed, a pop-up window is opened to introduce user and password o o o If user & password are properly introduced and entered, then the bottom-right-corner icon turns into a house. Once the house-button is pressed the pop-up window closes and the proper user level is set. If the password is wrongly introduced, the login window keeps open with the user-locked icon (left picture above). If the log-in pop-up window is closed with the X button at the top-right corner, then the lowest user level is set. NOTE: tab key is not available to switch from user field to password field and vice versa. Log-out button o displayed in all pages when some user is logged-in o Once pressed, it logs-out and moves to the home page. NOTE: If no action is done in the web page during 5 minutes, the user is automatically logged-out Clock button o displayed in all pages (only to User/Admin) o this button moves to the time-scheduling page ADALINK II-IOM-1401-E - 8 -
Hand button o displayed only in the home page (only to Admin) o Once pressed, it allows the configuration of the rooftop units connected to the Adalink II. o Up to 16 rooftop icons will appear on the top of the page. Each icon has a unique network address (from 1 to 16) as indicated in the picture o Once a unit is selected by clicking on the corresponding icon, the following settings can be adjusted by the box at the right corner Unit enable (checking the top-right corner box) Unit label Unit model (CLIMATIC 60 or CLIMATIC 50) Icon position can be adjusted over the background image throw the dedicated arrow buttons. Back-arrow button o displayed in the top bar to all users o it moves to previous page visited Wrench & Screw-driver button o Displayed in the top bar (only to Admin) o Once pressed it opens a pop-up window which allows to set: Network settings AdalinkII IP address Netmask Gateway Current mode setpoint editing button o displayed at the top bar of the unit page (only to User/Admin) o Once pressed it opens a pop-up window which allows to set : Unit On/Off Cooling setpoint Heating setpoint Dehumidification setpoint (visible only if humidity kit is present) Humidification setpoint (visible only if humidity kit is present) Minimum fresh air setpoint Blower fan active in dead zone Nominal blower fan speed NOTES: Setpoints modification must be validated by Enter button pressure, before to be sent. These setpoints will keep operative till next time-zone scheduled. When unit is Off, all the setpoints except On/Off are hidden. Lennox Service parameter o displayed at the top bar of the unit page only to User4 ADALINK II-IOM-1401-E - 9 -
o Once pressed it moves to Lennox-Service page where restricted parameters are available (read/write) Unit-Zone selection o Displayed in the top bar of the scheduling page (only to User/Admin) o Once pressed it opens a pop-up window which allows to set the zone settings to be applied to each unit (several units could share the same zone settings) 4.2 - BOTTOM BAR BUTTONS Placed at the bottom of the page. Wrench button o displayed at the low-right corner close to the date & hour (only to User) o once pressed, it opens a pop-up window to adjust the clock settings: date, hour and enable/disable automatic winter/summer time. NOTES: Respect the date format: dd.mm.yy and the hour format: hh:mm:ss CLIMATIC clock is automatically synchronized with Adalink clock every day at 4a.m. Refresh button o displayed in the bottom bar closed to the user level (only to User/Admin) o once pressed, it opens a pop-up window to change the password of the current user level. Backward-arrow blue button cancels and moves to the previous page; refresh red button saves the new password and moves to the previous page. ADALINK II-IOM-1401-E - 10 -
4.3 - TIME ZONES SCHEDULING PAGE This page is entered by pressing the button from the top page bar. GENERAL Up to 4 time-zones can be scheduled per day on weekly basis Up to 12 additional time-zones can be scheduled on year basis through the holiday planning (holiday planning zones have priority over weekly-planning zones) Up to 4 modes (Night, Day, Day 1, Day 2) selectable per time-zone ADALINK II-IOM-1401-E - 11 -
WEEKDAY ZONE SCHEDULING Number of zones of the day (up to 4) Zone starting time (format hh:mm) Zone mode (Night, Day, Day1, Day2) Zone ending time (format hh:mm) Current zone status (green when active) HOLIDAY PLANNING SCHEDULING Number of holiday zones (up to 12) Zone mode (Night, Day, Day1, Day2) Zone starting time (format hh:mm) Zone ending date (format dd.mm) Zone starting time (format hh:mm) Current zone status (green when active) DEFAULT MODE The mode selected (Night, Day, Day1, Day2) is forced whenever no weekly nor holiday zone is actived at the moment. ADALINK II-IOM-1401-E - 12 -
ZONE SELECTION It selects the zone (area) which the weekly and holiday planning refer to. Up to 16 zones (areas) are selectable. Once the zone is selected, the button read must be pushed to refresh the relative zone scheduling. UNIT ZONE SELECTION The zone settings are applied to the associated units (several units can share the same zone settings). Unit-zone association is done by pressing the button and selecting the zone for each unit. NOTE Not configured unit will appear crossed ADALINK II-IOM-1401-E - 13 -
MODE SETTINGS Up to 4 modes (night, day, day1, day2) can be associated to each zone (weekly or holiday planning). The following set points are configurable for each mode. The parameters are used by the unit concerned only if the relative option is present (e.g. humidty setpoints works only in unit with humidity option). Note: all the settings are hidden if the unit is OFF 4.4 - ALARMS PAGE This page is entered by pressing the button from the top page bar. History index Alarm counter Unit concerned Alarm code and description Alarm starting time Alarm starting time Alarm acknowledge Ack Alarms Filter list by unit Alarm list can be filtered by unit number. ADALINK II-IOM-1401-E - 14 -
Different colors are used to identify the alarms: Pending and acknowledged = grey Pending and not acknowledged = red Not pending and not acknowledged = blue Not pending and not acknowledged = light blue WATCH OUT Alarms acknowledge is not an alarm reset, the acknowledge is used just to recognize the alarm in the AdalinkII alarm list (Units alarm reset is available only in the unit page). The alarm acknowledge is allowed only to admin users. 4.5 - GRAPHICAL TRENDS PAGE This page is entered by pressing the button from the top page bar of the unit page. Show/hide in the Unit concerne Variables label Axis Color line Graphic display can be modified scrolling time axis (<<scroll>>) or zooming in/out. The data can be downloaded in csv format through the Save Logs to file button. ADALINK II-IOM-1401-E - 15 -
4.6 - ACCESS MANAGEMENT The Adalink II allows up 8 users max connected at the same time. The system manages up to 4 accounts levels: User1 Visu : No password required; reading rights only User2 User : Password 2222; setpoint editing User3 Admin : Password 3333; time-scheduling and site-administration ADALINK II-IOM-1401-E - 16 -
lennoxemeia.com SALES OFFICES : BELGIUM AND LUXEMBOURG + 32 3 633 3045 RUSSIA +7 495 626 56 53 FRANCE +33 1 64 76 23 23 SPAIN +34 902 533 920 GERMANY +49 (0) 40 589 6235 0 UKRAINE +38 044 585 59 10 ITALY + 39 02 495 26 200 UNITED KINGDOM AND IRELAND +44 1604 669 100 NETHERLANDS + 31 332 471 800 POLAND +48 22 58 48 610 PORTUGAL +351 229 066 050 OTHER COUNTRIES : LENNOX DISTRIBUTION +33 4 72 23 20 00 ADALINK II-IOM-1401-E Due to Lennox s ongoing commitment to quality, the specifications, ratings and dimensions are subject to change without notice and without incurring liability. Improper installation, adjustment, alteration, service or maintenance can cause property damage or personal injury. Installation and service must be performed by a qualified installer and servicing agency