Single and three-phase energy meters MI certified versions with UTF certificates igital voltmeters, ammeters, wattmeters, frequency meters and cos meters igital multimeters and power analyzers, expandable, with graphic or icon C Connection to single, two and three-phase systems Ideal for distribution systems, electricity cogeneration and on-board machinery installations High measurement accuracy Totally programmable digital and analog inputs and outputs RS485, RS232, USB, Ethernet, Profibus P and M-Bus communication ports SEC. - PGE Energy meters Single-phase... - 8 Single-phase, MI certified... - 9 Three-phase with or without neutral... - 10 Three-phase with neutral, MI certified... - 11 Three-phase with neutral, MI certified with UTF certificate... - 12 Current transformers with UTF certificates... - 13 ata concentrators General use... - 14 igital metering instruments Modular C multimeters... - 15 Flush-mount C multimeters... - 17 Flush-mount touch-screen C power analyzers... - 19 Flush-mount E measuring instruments... - 20 Flush-mount E multimeters... - 22 Modular E measuring instruments... - 25 Communication devices, protection covers, accessories... - 27 Converter, gateway, connecting cables... - 28 Current transformers... - 29 imensions... - 32 Wiring diagrams... - 35... - 38
Page -8 EERGY S Single-phase, three-phase with neutral, three-phase with or without neutral irect connection or by current transformers MI certified versions Versions expandable with EXM... expansion modules Versions with built-in RS485 or M-Bus communication ports. Page-14 T CCETRTRS Energy consumption data storage for network usage Connection up to 14 energy meters equipped with static output Expandable with EXM... expansion modules Built-in RS485 communication port. Page-15 IGIT C MUTIS PWER YZERS Graphic or icon C Modular and flush-mount 96x96mm versions Versions expandable with EXM... and EXP... expansion modules Version with built-in RS485 communication port. Version with current reading through Rogowski coils. Page-19 PRTBE PWER YZERS IP65 housing With built-in USB interface GPRS/GSM communications vailable kits of current clamps and cables. Page-20 E MESURIG ISTRUMETS Voltmeters, ammeters, frequency meters, cos meters and wattmeters. IGIT E MUTIS Basic version, with energy meters, with 2 programmable outputs and built-in RS485 communication port. CURRET TRSFRMERS Primary current: 50-4000 Secondary current: 5 Solid and split-core types Instrument and accuracy versions. Page -29
SYSTEM MGEMET MV/V transformer room MG 900 + EXP10 31 Energy Quality E 50160 MG 800 + EXP10 04 Temature control Primary distribution MG 800 ME 310 T2 (MI) MG 800 MG 700 MG 600 - MG 610 (MCC) M M M M Secondary distribution MG 300 MG 210 MG 200 MG 800 + EXP... Process and ambient control MG 100 MG 110 ME 330 ME 310 T2 ME 300 T2 ME 100 T1 ME 110 T1 ME 115 T1 ME 120 T1 ME C -2
MG SERIES MUTIS ME SERIES EERGY S Energy quality verification Energy consumption monitoring Energy quality analysis according to E 50160 Water Pressure larms PT100 temature 4-20m 0-10V Process data collection Control and diagnostic Boolean logic combination -3
igital metering instruments MITRIG CTR EVICES ETWRK ITERFCES Third party device Generating set control unit Power factor controller Power analyzer RS485/Ethernet converter Switch / Router Energy meter Soft starter Variable speed drives Gateway modem GPRS - 2G/3G Multimeter Multimeter Micro PC Switch / Router Gateway data logger GPRS - 2G/3G Process and environment data -4
igital metering instruments MITRIG SFTWRE GRPHIC ITERFCE VI WEB MITRIG PGES for the test of instantaneous data T G for data storage GRPHICS for the representation over time of the data collected from the data logs REPRT for the processing of time band data or consumption users -5
Energy meters SIGE-PHSE IRECT CECTI ME 100 T1 ME 110 T1 ME 115 T1 ME 120 T1 ME 121 ME 122 ME 130 M Maximum current 40 40 40 63 63 63 63 isplay Vertical, no backlight Horizontal, backlight Measurements kwh kwh, kw with average and max demand kwh, kvarh, kw with average and max demand, kvar, V, I, Hz, PF, total and partial hour counter Interface Pulse output Programmable output (pulses/thresholds) Built-in Modbus RTU (RS485) Built-in M-Bus MI version availability oad management Compatibility with, and software THREE-PHSE ME 300 T2 ME 301 ME 302 ME 305 T2 ME 330 ME 332 ME 310 T2 Maximum current 80 80 80 CT /5 or CT /1 CT /5 or CT /1 CT /5 or CT /1 CT /5 Connection type irect Via CT Interface Programmable output (pulses/thresholds) Built-in Modbus RTU (RS485) Built-in M-Bus Expandability Communication (RS485, Ethernet, USB) Relay outputs for load disconnection ata memory (ata logger) MI version availability❶ Compatibility with, and software ❶ UTF-certified versions are available on request. -6
Multimeters and power analyzers I RI MUTIG (MUR) MG 100 MG 110 MG 200 MG 210 MG 300 Maximum rated voltage 600VC 600VC 690VC 690VC 690VC Voltage and current measure accuracy 0.5% 0.5% 0.5% 0.5% 0.2% ctive energy measure accuracy Class 1 Class 1 Class 1 Class 1 Class 0.5s Single-phase energy meter Harmonic analysis 15 order 15 order TH only TH only 31 order Boolean logic Expandable with EXM... modules 3 modules isplay type Icons Icons Graphic Graphic Graphic Built-in communication port RS485 RS485 Communication port with EXM... modules RS232 USB RS485 Ethernet Ethernet-RS485 gateway function FUSH-MUTIG (96x96mm/3.78 x3.78 ) MG 600 MG 610 MG 700 MG 800 MG 900 MG 900T + MG 611 MG 900R Maximum rated voltage 600VC 600VC 690VC 690VC 690VC 690VC Current reading CT /5 or CT /5 or CT /5 CT /5 or CT /5 or CT /5 or /1 /1 (for MG 610) /1 /1 /1 Rogowski coils (for MG 611) Voltage and current measure accuracy 0.5% 0.5% 0.5% 0.2% 0.2% 0.2% ctive energy measure accuracy Class 1 Class 1 Class 1 Class 0.5s Class 0.5s Class 0.5s Single-phase energy meter Harmonic analysis 15 order 15 order TH only 31 order 63 order 63 order eutral-earth voltage eutral current Calculated Calculated Calculated Calculated Calculated or Calculated or measured via CT measured via CT Boolean logic Expandable with EXP... modules 1 module 1 module 4 modules 4 modules 4 modules 4 modules isplay type Icons Icons Graphic Graphic Graphic Graphic (MG900R) Built-in communication port RS485 RS485 or RS232 selectable Communication port with EXP... modules RS232 RS232 RS232 RS232 RS232 RS232 USB USB USB USB USB USB RS485 RS485 RS485 RS485 RS485 RS485 Ethernet Ethernet Ethernet Ethernet Ethernet Ethernet Profibus P slave Profibus P slave Profibus P slave GSM/GPRS GSM/GPRS Ethernet-RS485 gateway function Energy quality according to E50160 egree of protection IP54 IP54 IP65 IP65 IP65 IP65 (MG 900R) -7
Energy meters Single-phase ME M100 ME 110 T1... ME 115 T1... ME 120 T1... ME 121 - ME 122 Single-phase oad management ME 130M new new rder code escription Qty Wt pkg n [kg] Mechanical meter with mechanical display. ME M100 32 direct connection, 1U 1 0.084 ME M100 T1 32 direct connection, 1U 1 0.088 1 pulse output igital meter, with C screen. ME 100 T1 40 direct connection, 1U 1 0.086 1 pulse output, 220...0VC ME 100 T1 120 40 direct connection, 1U 1 0.086 1 pulse output, 110...120VC ME 110 T1 40 direct connection, 1U 1 0.090 1 program. static output, multimeasurements❶, 220...0VC ME 110 T1 120 40 direct connection, 1U 1 0.090 1 program. static output, multimeasurements❶,110...120vc igital meter with backlight C display. ME 115 T1 40 direct connection, 2U, 1 0.090 1 program. static output, multimeasurements ❷, 220-0VC ME 120 T1 63 direct connection, 2U 1 0.148 1 program. static output, multimeasurements ❶, 220-0VC ME 120 T1 120 63 direct connection, 2U 1 0.148 1 program. static output, multimeasurements❶, 110...120VC ME 121 63 direct connection, 2U, 1 0.148 RS485 interface multimeasurements ❶, 220-0VC ME 122 63 direct connection, 2U, 1 0.148 M-Bus interface multimeasurements ❶, 220-0VC rder code escription Qty Wt pkg n [kg] igital meter with backlight C display load management. ME 130 M 63 direct connection, 4U, 1 0.148 multi-measurement❶, 2 inputs and 2 relay outputs for load management, 220...0VC The energy meters are instruments for energy consumption measurement in single-phase installations with direct connection. ational characteristics ME M... Mechanical meter with 6+1 digit count Rated supply voltage: 230VC -20...+15% irect connection 32 maximum current ctive energy measurement and accuracy: Class 1 (IEC/E 62053-21) Flashing E for consumption indication Static pulse output for ME M100 T1 only Modular I 43880 housing, 1 module Sealable terminal blocks, standard supplied IEC degree of protection: IP40 on front; IP20 at terminals. ME 100 T1 ME 110 T1 ME 115 T1 ME 120 T1 ME 121 ME 122 ME 130M C meter : with 5+1 digit count for ME 100 T1, ME 110 T1...; backlight with 6+1 digit count for ME 115 T1, ME 120 T1, ME 121, ME 122, ME 130M ominal supply voltage: 220...0VC for ME...T1 110...120C for ME...T1 120 Voltage range: 187...264VC for ME...T1 93...132VC for ME...T1 120 irect connection Maximum current: 40 for ME 100 T1, ME 110 T1..., ME 115 T1; 63 for ME 120 T1 ME 121 ME 122 ME 130M ctive energy measurement and accuracy: Class 1 (IEC/E 62053-21) Reactive energy measurement and accuracy: Class 2 (IEC/E 62053-23) Metrological E with pulse emission for consumption indication Clearable partial energy measurement ne output: pulse for ME 100 T1; programmable static for all other types Built-in RS485 port for ME 121; compatible with e Built-in M-Bus port for ME 122 Modular housing: 1 module for ME 100 T1, ME 110 T1; 2 module for all other types Sealable terminal blocks, standard supplied E degree of protection: IP40 on front; IP20 at terminals. suvision and energy management software See Section 29. configuration and remote control software See Section 29. Certifications and compliance Certifications obtained: EC; U isted, for US and Canada (File E346886), as Electrical Process Control Equipment - Energy meters, for ME 100..., ME 110..., ME 120..., ME 121 types. Compliant with standards: IEC/E 61326-1 for ME M... type; IEC/E 50470-1, IEC/E 61010-1 for ME... types; U 61010-1, CS C22-2 n 61010-1 for ME 100..., ME 110..., ME 120..., ME 121. Enable / disable ❶ Multi-measurements: - Total and partial active energy - Total and partial reactive energy - Voltage - Current - ctive and reactive power - Power factor - Frequency - Total and partial hour counter - verage active power (calculation made using the last 15 minutes of data) - Maximum demand. Priority loads oads that can be managed ❷ Multi-measurements: - Total and partial active energy - ctive power - verage active power (calculation made using the last 15 minutes of data) - Maximum demand. -8 Software and accessories pages -27 and 28 imensions page -32 Wiring diagrams page -35 pages -38 and 39
Energy meters MI certified Single-phase, MI certified MI ME 110 T1 MI ME 120 T1 MI new rder code escription Qty Wt pkg n [kg] igital meter with C display. ME 100 T1 MI 40 direct connection, 1U 1 0.086 1 pulse output, 230VC ME 110 T1 MI 40 direct connection, 1U 1 0.090 1 programmable static output, multi-measurements ❶, 230VC ME 120 T1 MI 63 direct connection, 2U 1 0.148 1 programmable static output, multi-measurements ❶, 230VC ME 121 MI 63 direct connection, 2U, 1 0.148 RS485 interface multi-measurements ❶, 220...0VC ME 122 MI 63 direct connection, 2U, 1 0.148 M-Bus interface multi-measurements ❶, 220...0VC The ME series energy meters, MI certified, are needed for billing purposes between electricity supplliers and consumers and for energy consumption measurement in directly connected single-phase installations. MI is the Measuring Instruments irective of the European Union; instruments must be certified accordingly whenever used for monetary transactions in this territory. ational characteristics C meter: With 5+1 digit count for ME 100/110 T1 MI Backlight with 6+1 digit count for all other types ominal supply voltage: 230VC Voltage range: 187-264VC 50Hz irect connection Maximum current: 40 for ME 100/110 T1 MI 63 for ME 120 T1 MI, ME 121 MI, ME 122 MI ctive energy measurement and accuracy: Class B (E 50470-3) Reactive energy measurement and accuracy: Class 2 (IEC/E 62053-23) Metrological E with pulse emission for consumption indication Clearable partial energy measurements ne output: pulse for ME 100 T1 MI; programmable static for other types Built-in RS485 port for ME 121 MI; compatible with and Built-in M-Bus port for ME 122 MI Modular housing, 1 module for ME 100 T1, ME 110 T1 MI; 2 module for other types Sealable terminal blocks, standard supplied E degree of protection: IP40 on front; IP20 at terminals. suvision and energy management software See Section 29. configuration and remote control software See Section 29. Certifications and compliance Certifications obtained: MI Class B (E 50470-1, E 50470-3), certifications module B (type tests) + module (production conformity). Compliant with standards: E 50470-1, E 50470-3, TR50579. ❶ Multi-measurements: - Total and partial active energy - Total and partial reactive energy - Voltage - Current - ctive and reactive power - Power factor - Frequency - Total and partial hour counter - verage active power (calculation made using the last 15 minutes of data) - Maximum demand. Software and accessories pages -27 and 28 imensions page -32 Wiring diagrams page -35 pages -38 and 39-9
Energy meters Three-phase with or without neutral, non expandable ME 300 T2 ME 330 Three-phase with or without neutral, expandable ME 310 T2 EXM10 10 new new new rder code escription Qty Wt pkg n [kg] igital meter for three-phase with neutral. 80 direct connection. ME 300 T2 4U, 2 programmable 1 0.360 static outputs, multi-measurements ❶ ME 301 4U, RS485 interface, 1 0.360 multi-measurements❶ ME 302 4U, M-Bus interface, 1 0.360 multi-measurements❶ igital meter for three-phase with or without neutral. Connection by CT /5. ME 305 T2 4U, 2 programmable 1 0.332 static outputs, multi-measurements ❶ ME 330 4U, RS485 interface, 1 0.332 multi-measurements❶ ME 332 4U, M-Bus interface, 1 0.332 multi-measurements❶ rder code escription Qty Wt pkg n [kg] igital meter for three-phase with or without neutral. Connection by CT /5. ME 310 T2 4U, 2 programmable 1 0.332 static outputs, multi-measurements ❶, expandable rder escription code ME 310 T2 EXPSI MUES. Inputs and outputs. EXM10 00 2 digital inputs and 2 static outputs, opto-isolated EXM10 01 2 opto-isolated digital inputs and 2 relay outputs rated 5 250VC Communication ports. EXM10 10 EXM10 11 EXM10 12 EXM10 13 EXM10 20 EXM10 30 pto-isolated USB interface pto-isolated RS232 interface pto-isolated RS485 interface Ethernet interface with Web server function pto-isolated RS485 interface and 2 relay outputs rated 5 250VC ata storage, clock-calendar (RTC) with backup reserve energy for data logging The energy meters are digital meters/analyzers of electric energy for systems with direct three-phase connection or by CT. Expandable with up to 3 module EXM series by optical interface. ational characteristics C multifunction meter ominal supply voltage: 380...415VC (-) Voltage range: 323...456VC (-) ctive energy measurement and accuracy: Class 0.5s (IEC/E 62053-22) for ME 305T2, ME 330 and ME 332, Class 1❷ (IEC/E 62053-21) for ME 300T2, ME 301 and ME 302 ctive energy measurement and accuracy: Class 2 (IEC/E 62053-23) Metrological E with pulse emission for consumption indication Clearable partial active energy measurements 1 programmable digital input 2 programmable static outputs for ME 300T2, ME 305T2 and ME 310T2 Built-in RS485 port for ME 301 and ME 330; compatible with and Built-in M-Bus port for ME 302 and ME 332 ptical interface for EXM10... expansion modules with ME 310 T2 Modular housing, 4 module Sealable terminal blocks, standard supplied E degree of protection: IP40 on front; IP20 at terminals. suvision and energy management software See Section 29. configuration and remote control software See Section 29. EXM series expansion modules See page 30-3. Certifications and compliance Certifications obtained: EC for all types, RCM for ME 305T2, ME 310T2, ME 330. Compliant with standards: IEC/E 50470-1, IEC/E 61010-1, IEC 61010-2-030. ❶ Multi-measurements: - Total and partial active energy - Total and partial reactive energy - Voltage - Current - ctive and reactive power - Power factor - Frequency - Total and partial hour counter - verage active power (calculation made using the last 15 minutes of data) - Maximum demand. ❷ Class 1 according to IEC/E 62053-21, accuracy measured in the 0.75-80 range: 0.5% Maximum combination MX 3-10 Software and accessories pages -27 and 28 Expansion modules page 30-3 imensions page -32 Wiring diagrams page -35 page -40
Energy meters MI certified Three-phase with neutral, non expandable, MI certified MI ME 300 T2 MI Three-phase with neutral, expandable, MI certified MI ME 310 T2 MI EXM10 10 new rder code escription Qty Wt pkg n [kg] igital meter for three-phase with neutral. 80 direct connection. ME 300 T2 MI 2 programmable static 1 0.360 outputs, multi-measurements❶ ME 301 MI 4U, RS485 interface, 1 0.360 multi-measurements❶ ME 302 MI 4U, M-Bus interface, 1 0.360 multi-measurements❶ igital meter for three-phase with neutral. Connection by CT /5. ME 305 T2 MI 2 programmable static 1 0.332 outputs, multi-measurements❶ ME 330 MI 4U, RS485 interface, 1 0.332 multi-measurements❶ ME 332 MI 4U, M-Bus interface, 1 0.332 multi-measurements❶ rder code escription Qty Wt pkg n [kg] igital meter for three-phase with neutral. Connection by CT /5. ME 310 T2 MI 2 programm. static outputs, 1 0.332 multi-measurements❶, expandable, graphic C display rder escription code ME 310 T2 MI EXPSI MUES. Inputs and outputs. EXM10 00 2 digital inputs and 2 static outputs, opto-isolated EXM10 01 2 opto-isolated digital inputs and 2 relay outputs rated 5 250VC Communication ports. EXM10 10 EXM10 11 EXM10 12 EXM10 13 EXM10 20 EXM10 30 Maximum combination pto-isolated USB interface pto-isolated RS232 interface pto-isolated RS485 interface Ethernet interface with Web server function pto-isolated RS485 interface and 2 relay outputs rated 5 250VC ata storage, clock-calendar (RTC) with backup reserve energy for data logging The ME series energy meters, MI certified, are needed for billing purposes between electricity suppliers and consumers and for energy consumption measurement in directly or CT connected three-phase installations. Expandable with up to 3 module EXM series by optical interface. ational characteristics C multifunction meter ominal supply voltage: 230VC (-); 400VC (-) Voltage range: 187...264VC (-); 323...456VC (-) ctive energy measurement and accuracy: Class B (E 50470-3) Reactive energy measurement and accuracy: Class 2 (IEC/E 62053-23) Metrological E with pulse emission for consumption indication Clearable partial energy measurements 1 programmable digital input 2 programmable static outputs ME 300 T2 MI, ME 305 T2 MI and ME 310 T2 MI Built-in RS485 port for ME 301 MI and ME 330 MI; compatible with and Built-in M-Bus port for ME 302 and ME 332 ptical interface for EXM10... expansion modules with ME 310 T2 Modular housing 4 module Sealable terminal blocks, standard supplied E degree of protection: IP40 on front; IP20 at terminals. suvision and energy management software See Section 29. configuration and remote control software See Section 29. EXM series expansion modules See page 30-3. Certifications and compliance Certifications obtained: MI Class B (E 50470-1, E 50470-3), certifications module B (type tests) + module (production conformity). Compliant with standards: E 50470-1, E 50470-3, TR50579. ❶ Multi-measurements: - Total and partial active energy - Total and partial reactive energy - Voltage - Current - ctive and reactive power - Power factor - Frequency - Total and partial hour counter - verage active power (calculation made using the last 15 minutes of data) - Maximum demand. MX 3 Software and accessories pages -27 and 28 Expansion modules page 30-3 imensions page -32 Wiring diagrams page -35 page -40-11
Energy meters MI certified With UTF certificates Three-phase with neutral, MI certified ME 300 F EXM10 10 new new rder code escription Qty Wt pkg n [kg] igital meter for three-phase with neutral, non expandable, complete with UTF certificates for installations in Italy. ME 300 F ME 300 T2 MI, 1 0.360 complete with UTFcertificate ME 301 F ME 301 MI, 1 0.381 complete with UTFcertificate ME 305 F ME 305 T2 MI, 1 0.381 complete with UTFcertificate ME 330 F ME 330 MI, 1 0.381 complete with UTFcertificate igital meter for three-phase with neutral, expandable, complete with UTF certificates for installations in Italy. ME 310 F ME 310 T2 MI, 1 0.381 complete with UTFcertificate rder code escription ME 310 F EXPSI MUES. Inputs and outputs. EXM10 00 EXM10 01 EXM10 02 Communication ports. EXM10 10 EXM10 11 EXM10 12 EXM10 13 EXM10 20 EXM10 30 Maximum combination 2 digital inputs and 2 static outputs, opto-isolated 2 opto-isolated digital inputs and 2 relay outputs rated 5 250VC 4 opto-isolated digital inputs and 2 relay outputs rated 5 250VC pto-isolated USB interface pto-isolated RS232 interface pto-isolated RS485 interface Ethernet interface with Web server function pto-isolated RS485 interface and 2 relay outputs rated 5 250VC ata storage, clock-calendar (RTC) with backup reserve energy for data logging MX 3 The UTF (Finance Technical ffice) certification is required in case of applications where taxes have to be paid due to energy production (Italian regulations for plants >20kW). The certificates must be associated to the energy meter (MI version) and to each single current transformer in needed (see page -13 for selection). ME energy meters, MI version, for three-phase systems with or without current transformers can be supplied with the certificates included (ME...F). ME 310 F... can be expanded up to 3 EXM modules. If required, the fifth certificate relevant to the meter and current transformer combination can be supplied as well (see page -13). ational characteristics C multifunction meter ominal supply voltage: 230VC (-); 400VC (-) Voltage range: 187...264VC (-); 323...456VC (-) ctive energy measurement and accuracy: Class B (E 50470-3) Reactive energy measurement and accuracy: Class 2 (IEC/E 62053-23) Metrological E with pulse emission for consumption indication Clearable partial energy measurements 1 programmable digital input 2 programmable static outputs for ME 300 F, ME 305 F and ME 310 F Built-in RS485 port for ME 301 F and ME 330 F; compatible with e ptic interface for EXM10... expansion modules with ME 310 F Modular housing 4 module Sealable terminal blocks, standard supplied E degree of protection: IP40 on front; IP20 at terminals. Multi-measurements Total and partial active energy Total and partial reactive energy Voltage Current ctive and reactive power Power Factor Frequency Total and partial hour counter verage active power (calculation made using the last 15 minutes of data) Maximum demand. suvision and energy management software See Section 29. configuration and remote control software See Section 29. EXM series expansion modules See page 30-3. Certifications and compliance Certifications obtained: MI Class B (E 50470-1, E 50470-3), certifications module B (type tests) + module (production conformity) for ME 300 F and ME 310 F energy meters. UTF certificates are standard supplied. Compliant with standards: E 50470-1, E 50470-3, TR 50579. -12 Software and accessories pages -27 and 28 Expansion modules page 30-3 imensions page -32 Wiring diagrams page -35 page -40
Current transformers Current transformer kits with UTF certificates M... new rder code escription of CTs included Qty Wt pkg n [kg] Kit comprising of three /5 and class 0.5s current transformers M1TP 0060 F KIT 3 M1TP0060, complete 1 1.440 with UTF certificate M1TP 0080 F KIT 3 M1TP0080, complete 1 1.440 with UTF certificate M1TP 0100 F KIT 3 M1TP0100, complete 1 1.560 with UTF certificate M1TP 0150 F KIT 3 M1TP0150, complete 1 1.680 with UTF certificate M1TP 0200 F KIT 3 M1TP0200, complete 1 1.620 with UTF certificate M1TP 0250 F KIT 3 M1TP0250, complete 1 1.620 with UTF certificate M1TP 0300 F KIT 3 M1TP0300, complete 1 1.680 with UTF certificate M1TP 0400 F KIT 3 M1TP0400, complete 1 1.680 with UTF certificate M3TP 0500 F KIT 3 M3TP0500, complete 1 2.160 with UTF certificate M3TP 0600 F KIT 3 M3TP0600, complete 1 2.160 with UTF certificate M3TP 0800 F KIT 3 M3TP0800, complete 1 2.280 with UTF certificate M5TP 1000 F KIT 3 M5TP1000, complete 1 2.820 with UTF certificate M5TP 1250 F KIT 3 M5TP1250, complete 1 2.760 with UTF certificate M5TP 1600 F KIT 3 M5TP1600, complete 1 2.880 with UTF certificate M5TP 2000 F KIT 3 M5TP2000, complete 1 2.940 with UTF certificate M5TP 2500 F KIT 3 M5TP2500, complete 1 3.120 with UTF certificate M5TP 3000 F KIT 3 M5TP3000, complete 1 2.940 with UTF certificate The UTF (Finance Technical ffice) certification is required in case of applications where taxes have to be paid due to energy production (Italian regulations for plants >20kW). The certificates must be associated to the energy meter (MI version, see page -13 for selection) and to each single current transformer is needed. ME energy meters, MI version, for three-phase systems with or without current transformers can be supplied with the certificates included (ME...F). ME 310 F... can be expanded up to 3 EXM modules. If required, the fifth certificate relevant to the meter and current transformer combination can be supplied as well. The M...TP type accuracy current transformers (CTs) are installed in an electrical system to reduce the line current to a secondary value of 5 compatible with the ammeter inputs of the digital multimeters or protection relays. M...TP are accuracy current transformers in class 0.5s without a primary winding and are normally used for high primary current values starting from 60. The number of loops of the primary cable does not modify the accuracy but converts the primary current value proportional to secondary current (see page -30). ational characteristics ating frequency: 50 60Hz Secondary output current: 5 verload withstand: 120% Ipn Rated insulation voltage Ui: 720V Rated short time thermal current Ith: 40-60Ipn for 1 second Rated dynamic current Idyn: 2.5Ith for 1 second Insulation (dry type): class E Screw fixing terminals Sealable terminal covers Fixing on 35mm I rail (IEC/E 60715) or by screws (fixing elements standard supplied with the product) E degree of protection: IP30. mbient conditions ating temature: -25...+50 C Storage temature: -40...+80 C. Relative humidity, non condensing: 90%. Compliance Compliant with standards: IEC/E 61869-2, IEC/E 61869-1. Certificate for whole system rder code M CERT UTF escription UTF system certificate imensions page -33-13
ata concentrator Expandable rder code escription Qty Wt pkg n [kg] ata concentrator for general use. ME C EXM10 10 ME C With 8 programmable 1 0.337 digital inputs, expandable, for data collection + pulse count from MEM100T1 and ME, RS485 port rder code escription ME C EXPSI MUES. Inputs and outputs. EXM10 00 2 digital inputs and 2 static outputs, opto-isolated EXM10 01 2 opto-isolated digital inputs and 2 relay outputs rated 5 250VC EXM10 02 4 opto-isolated digital inputs and 2 relay outputs rated 5 250VC Communication ports. EXM10 10 EXM10 11 EXM10 12 EXM10 13 EXM10 20 EXM10 30 Maximum combination pto-isolated USB interface pto-isolated RS232 interface pto-isolated RS485 interface Ethernet interface with Web server function pto-isolated RS485 interface and 2 relay outputs, rated 5 250VC ata storage, clock-calendar (RTC) with backup reserve energy for data logging ME C is equipped with 8 inputs, which can be increased up to a maximum of 14 and allows to indirectly interface devices without communication as long as they have at least one pulse output. It is capable of pulse counting that comes in from the outputs of meters for energy, water, gas and other types of consumption: ll data is viewed on its display or can also be available for PCs through its built-in RS485 interface using or software. It can be expanded with up to 3 EXM series modules by optical interface. With the programmable functions, average values can be determined for instantaneous quantities, such as power, speed, production rate, gas and water consumption, etc. ational characteristics C multifunction meter ominal supply voltage: 100...0VC/110...250VC Voltage range: 85...264VC/93.5...300VC Backlight graphic C 8 inputs, expandable with EXM 10 modules up to 14 Built-in RS485 communication port Modbus-RTU, SCII and TCP communication protocol Clearable total and partial counters for each channel Programmable general counters Calculation of derivative average values Mathematical oations among counters Modular housing, 4 module E degree of protection: IP40 on front; IP20 at terminals. suvision and energy management software See Section 29. configuration and remote control software See Section 29. EXM series expansion modules See page 30-3. Certifications and compliance Certifications obtained: EC for all; U listed for US and Canada (cuus File E346886), as Electrical Process Control Equipment ata concentrator for ME C. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-3. MX 3-14 Software and accessories pages -27 and 28 Expansion modules page 30-3 imensions page -32 Wiring diagrams page -35 page -41
igital metering instruments. Metering and current transformer kits Modular C multimeters, non expandable MG 1... MG 200 - MG 210 rder escription Qty Wt code pkg. n [kg] MG 100 Icon C, auxiliary supply 1 0.294 100...0VC/120...250VC. Multilanguage: Italian, English, French, Spanish, Portuguese and German MG 110 Icon C, RS485 port, 1 0.294 auxiliary supply 100...0VC/120...250VC. Multilanguage: Italian, English, French, Spanish, Portuguese and German MG 200 Graphic128x80 pixel C, 1 0.294 auxiliary supply 100-0VC/110-250VC. Multilanguage: Italian, English, French, Spanish and Portuguese MG 200 01 Graphic128x80 pixel C, 1 0.294 auxiliary supply 100-0VC/110-250VC. Multilanguage: English, Czech, Polish, German and Russian MG 210 Graphic128x80 pixel C, 1 0.300 RS485 port, auxiliary supply 100-0VC/110-250VC. Multilanguage: Italian, English, French, Spanish and Portuguese MG 210 01 Graphic128x80 pixel C, 1 0.300 RS485 port, auxiliary supply 100-0VC/110-250VC. Multilanguage: English, Czech, Polish, German and Russian Kits with CT rder code escription Qty Wt pkg MG KIT 100 150 n [kg] MG KIT 100 060 Composed of one 1 1.035 MG 100 multimeter and n 3 CTs 60/5 for Ø22mm cable MG KIT 100 100 Composed of one 1 1.035 MG 100 multimeter and n 3 CTs 100/5 for Ø22mm cable MG KIT 100 150 Composed of one 1 0.856 MG 100 multimeter and n 3 CTs 150/5 for Ø23mm cable MG KIT 100 250 Composed of one 1 0.856 MG 100 multimeter and n 3 CTs 200/5 for Ø23mm cable MG... digital multimeters are available with a modular housing, 4 module size, and are equipped with a graphic backlight C (except MG 100/110 with icon display) capable of providing extremely clear, intuitive and flexible viewing of all electrical parameters of an installation. For MG 110 and MG 210 versions, there is a built-in isolated RS485 interface. Main measurements: Voltage: phase, line and system values Current: phase values (neutral current calculated) Power: apparent, active and reactive phase and total values P.F.: Power Factor phase and total Frequency of measured voltage value HIGH-W-VERGE value functions of all measurements Maximum demand of power and current values symmetric voltage and current Total harmonic distortion (TH) of voltage and current values Energy meters for active, reactive and apparent values Hour counter (total and partial, 1 on MG 200/210, 4 programmable on MG 100/110) Phase energy (MG 100/110) Harmonic analysis up to the 15th order (MG 100/110). ational characteristic uxiliary supply voltage range: 100...0VC / 110...250VC Maximum rated measurement voltage 600VC (MG 100/110) 690VC (MG 200/210) Voltage measurement range: 50...720VC phase-to-phase (MG 100/110) 20...830VC phase-to-phase (MG 200/210) Usage in medium and high-voltage systems with voltage transformers Rated input current: With external CT /5 (also 1 for MG 100/110) Current measurement range with CT up to 10,000 Frequency measurement range: 45-66Hz True RMS measurements for voltage and current values ccuracy: Voltage: ±0.5% (50...720VC for MG 1...) (50...830VC) for MG 2... Current: ±0.5% (0.1...1.1In) Power: ±1% f.s. Frequency: ±0.05% ctive energy: Class 1 (IEC/E 62053-21) Reactive energy: Class 2 (IEC/E 62053-23) on-volatile memory for data storage Communication protocol Modbus-RTU and SCII (only for MG 210 and MG 110) Programming and remote control by software (only for MG 210 and MG 110; compatible with and software) Modular housing, 4 module E degree of protection: IP40 on front; IP20 at terminals. CURRET TRSFRMERS F MG KITS ating frequency: 50...60Hz Secondary output current: 5 verload withstand: 120% Ipn Rated insulation voltage Ui: 720V Rated short time thermal current Ith: 40 60Ipn for 1 second Rated dynamic current Idyn: 2.5Ith for 1 second Insulation (dry type): class E Faston terminals E degree of protection: IP30. suvision and energy management software See Section 29. configuration and remote control software See Section 29. Certifications and compliance Certifications obtained: EC and RCM for all; U isted for US and Canada (cuus - File E93601), as uxiliary evices - Multimeter for MG 1.../MG 2... types. Compliant with standards: MG100/110: IEC/E 61010-1, IEC/E 61010-2-030, IEC/E 61000-6-2, IEC/E 61000-6-3, U 61010-1, CS C22.2 n 61010-1, U 61010-2-030, CS 22.2 n 61010-2-030. MG200/210: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-4, U 61010-1, U508, CS C22.2 n 14. Software and accessories pages -27 and 28 imensions page -32 Wiring diagrams page -36 page -42-15
igital metering instruments Modular C multimeters, expandable MG 300 EXM10 10 rder escription Qty Wt code pkg n [kg] MG 300 Graphic 128x80 pixel C, 1 0.320 harmonic analysis, auxiliary supply 100-0VC/110-250VC, expandable with modules series EXM... Multilanguage: Italian, English, French, Spanish and Portuguese MG 300 01 Graphic 128x80 pixel C, 1 0.320 harmonic analysis, auxiliary supply 100-0VC/110-250VC, expandable with modules series EXM... Multilanguage: English, Czech, Polish, German and Russian rder escription code MG 300 MG 300 01 EXPSI MUES. Inputs and outputs. EXM10 00 EXM10 01 2 digital inputs and 2 static outputs, opto-isolated 2 opto-isolated digital inputs and 2 relay outputs rated 5 250VC EXM10 02 4 opto-isolated digital inputs and 2 relay outputs rated 5 250VC Communication ports. EXM10 10 EXM10 11 EXM10 12 EXM10 13 EXM10 20 EXM10 30 Maximum combination pto-isolated USB interface pto-isolated RS232 interface pto-isolated RS485 interface Ethernet interface with Web server function pto-isolated RS485 interface and 2 relay outputs rated 5 250VC ata storage, clock-calendar (RTC) with backup battery for data logging MX 3 MG 300 digital multimeters are available with a modular housing, 4 module size, and are equipped with a graphic backlight C capable of providing extremely clear, intuitive and flexible viewing of all electrical parameters of a system. The very accurate measurements combined with their extreme compactness provide an ideal solution for every type of application. Expandable with up to 3 module EXM series by optical interface. Main measurements: Voltage: phase, line and system values Current: phase values (neutral current calculated) Power: apparent, active and reactive phase and total values P.F.: Power Factor phase and total Frequency of measured voltage value HIGH-W-VERGE value functions for all measuements Maximum demand of power and current values Voltage and current asymmetry Total harmonic distortion (TH) of voltage and current values Harmonic analysis of voltage and current up to 31 order Energy meters for active, reactive, apparent partial and total values, programmable tariff functions Hour counter for programmable total and partial hours Pulse counter for general use: consumption pulse counting for water, gas, etc. with expansion module only. ational characteristics uxiliary supply voltage range: 85...264VC / 93.5...300VC Voltage measurement range: 20...830VC phase-to-phase 10...480VC phase-neutral Usage in medium and high-voltage systems with voltage transformers Rated input current: With external CT, 5 or 1 Current measurement range with CT up to 10,000 Frequency measurement range: 45-66Hz True RMS measurements for voltage and current values ccuracy: Voltage: ±0.2% (50...830VC) Current: ±0.2% (0.1...1.1In) Power: ±0.5% f.s. Power factor: ±0.5% Frequency: ±0.05% ctive energy: Class 0.5s (IEC/E 62053-22) Reactive energy: Class 2 (IEC/E 62053-23) on-volatile memory for data storage Communication protocol Modbus - RTU, SCII and TCP (only with communication expansion modules) Programming and remote control by software (only with communication expansion modules); compatible with and software Modular housing, 4 module E degree of protection: IP40 on front; IP20 at terminals. suvision and energy management software See Section 29. configuration and remote control software See Section 29. EXM series expansion modules See page 30-3. Certifications and compliance Certifications obtained: EC and RCM for all; U isted, for US and Canada (cuus - File E93601), as uxiliary evices - Multimeters. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-4, U508, CS C22.2 n 14. -16 Software and accessories pages -27 and 28 Expansion modules page 30-3 imensions page -32 Wiring diagrams page -36 page -42
igital metering instruments Flush-mount C multimeters, expandable MG 600 - MG 610 MG 611 R... ❶ Italian, English, French, Spanish and Portuguese. new rder escription Qty Wt code pkg n [kg] MG 600 Backlight icon 72x46mm C, 1 0.300 harmonic analysis, auxiliary supply 100...440VC/120... 250VC, front optical port. Multilanguage❶ MG 610 Backlight icon 72x46mm C, 1 0.350 harmonic analysis, auxiliary supply 100...440VC/120... 250VC, front optical port, built-in RS485 serial port. Multilanguage❶ MG 611 R 0100 Backlight icon 72x46mm C, 1 0.350 harmonic analysis, auxiliary supply 100 440VC/120 250VC, front optical port, built-in RS485 serial port. Multilanguage❶. Current reading through 3 Rogowski coils included, max current 100 MG 611 R 0500 Backlight icon 72x46mm C, 1 0.350 harmonic analysis, auxiliary supply 100 440VC/120 250VC, front optical port, built-in RS485 serial port. Multilanguage❶. Current reading through 3 Rogowski coils included, max current 500 MG 611 R 3000 Backlight icon 72x46mm C, 1 0.350 harmonic analysis, auxiliary supply 100 440VC/120 250VC, front optical port, built-in RS485 serial port. Multilanguage❶. Current reading through 3 Rogowski coils included, max current 3000 MG 611 R 6300 Backlight icon 72x46mm C, 1 0.350 harmonic analysis, auxiliary supply 100 440VC/120 250VC, front optical port, built-in RS485 serial port. Multilanguage❶. Current reading through 3 Rogowski coils included, max current 6300 MG 600/610/611 digital multimeters are capable of viewing the measurements with high accuracy on the wide graphic C, which allow to control energy distribution networks. They are available with a flush-mount housing, (96x96mm/3.78 x3.78 ) and 1 expansion slot to fit plug-in expansion modules, suitable for numerous applications. The main features include an extended power supply voltage range, high measurement accuracy, expandability and graphic interactive interface for simple use. Main measurements: Voltage: phase, line and system values Current: phase values (neutral current calculated) Power: apparent, active and reactive phase and total values P.F.: Power Factor phase and total Frequency of measured voltage value HIGH-W-VERGE value functions for all measurements Maximum demand of power and current values Voltage and current asymmetry Total harmonic distortion (TH): voltage and current Harmonic analysis of voltage and current up to the 15 order Energy meters for active, reactive, apparent partial and total values Hour counter for programmable total and partial hours. ational characteristics uxiliary supply voltage range: 100...440VC / 110...250VC Voltage measurement range: 50...720VC - Usage in medium and high voltage systems with voltage transformers Rated input current: By external CT 5 or 1 Current reading through Rogowski coils for MG 611... Frequency measurement range 45...66Hz True RMS measurements: for voltage and current Measurement accuracy: Voltage: ±0.5% (50...720VC) Current: ±0.5% (0.1...1.1In) Power: ±1% f.s. Frequency: ±0.05% ctive energy: Class 1 (IEC/E 62053-21) Reactive energy: Class 2 (IEC/E 62053-23) on-volatile memory for data storage Communication protocol Modbus-RTU, SCII and TCP Compatible and sofware Flush-mount housing 96x96mm/3.78 x3.78 E degree of protection: IP54 on front. suvision and energy management software See Section 29. configuration and remote control software See Section 29. EXP10... rder escription code EXPSI MUES Inputs and outputs. EXP10 00 4 opto-isolated digital inputs EXP10 01 EXP10 02 EXP10 03 4 opto-isolated static outputs 2 digital inputs and 2 static outputs, opto-isolated 2 relay outputs rated 5 250VC EXP10 08 2 opto-isolated digital inputs and 2 relay outputs rated 5 250VC Communication ports. EXP10 10 EXP10 11 EXP10 12 EXP10 13 pto-isolated USB interface pto-isolated RS232 interface pto-isolated RS485 interface pto-isolated Ethernet interface EXM series expansion modules See page 30-2. Certifications and compliance Certifications obtained: EC and RCM for all; U listed for US and Canada (cuus File E93601), as uxiliary evices Multimeters. Compliant with standards: IEC/E 61010-1, IEC/E 61010-2-030, IEC/E 61000-6-2, IEC/E 61000-6-3, U 61010-1, CS C22.2 n 61010-1, U 61010-2-030, CS 22.2 n 61010-2-030. Software and accessories pages -27 and 28 Expansion modules page 30-2 imensions page -32 Wiring diagrams page -36 page -43-17
igital metering instruments Flush-mount C multimeters, expandable MG 700 - MG 800... EXP10... rder escription Qty Wt code pkg n [kg] MG 700 Graphic 128x80 pixel C, 1 0.510 auxiliary supply 100...440VC/110...250VC Multilanguage❶ MG 700 01 Graphic 128x80 pixel C, 1 0.510 auxiliary supply 100...440VC/110...250VC Multilanguage❷ MG 800 Graphic 128x80 pixel C, 1 0.510 harmonic analysis, auxiliary supply 100...440VC/110...250VC Multilanguage❶ MG 800 01 Graphic 128x80 pixel C, 1 0.510 harmonic analysis, auxiliary supply 100...440VC/110...250VC Multilanguage❷ MG 800 048 Graphic 128x80 pixel C, 1 0.520 harmonic analysis, auxiliary supply 12--48VC ❶ Italian, English, French, Spanish and Portuguese. ❷ English, Czech, Polish, German and Russian. rder escription code EXPSI MUES Inputs and outputs. EXP10 00 EXP10 01 EXP10 02 EXP10 03 EXP10 04 EXP10 05 4 opto-isolated digital inputs 4 opto-isolated static outputs 2 digital inputs and 2 static outputs, opto-isolated 2 relay outputs rated 5 250VC 2 opto-isolated analog inputs 0/4-20m or PT100 or 0-10V or 0...±5V for MG 800 2 opto-isolated analog outputs 0/4-20m or 0-10V or 0...±5V for MG 800 EXP10 08 2 opto-isolated digital inputs and 2 relay outputs rated 5 250VC Communication ports. EXP10 10 EXP10 11 EXP10 12 EXP10 13 EXP10 14 EXP10 30 pto-isolated USB interface pto-isolated RS232 interface pto-isolated RS485 interface pto-isolated Ethernet interface pto-isolated Profibus-P interface for MG 800 ata storage, clock-calendar (RTC) with backup reserve energy for data logging for MG 800 MG 700 and MG 800 digital multimeters are capable of viewing the measurements with high accuracy on the wide graphic C, which allow to control energy distribution networks. They are available with a flush-mount housing, (96x96mm/3.78 x3.78 ) with 4 expansion slots to fit plug-in expansion modules, suitable for numerous applications. The main features include an extended power supply voltage range, high measurement accuracy, expandability and graphic interactive interface for simple use. Main measurements: Voltage: phase, line and system values Current: phase values (neutral current calculated) Power: apparent, active and reactive phase and total values P.F.: Power Factor phase and total Frequency of measured voltage value HIGH-W-VERGE value functions for all measurements Maximum demand of power and current values Voltage and current asymmetry Harmonic analysis of voltage and current up to the 31 order (only MG 800) Energy meters for active, reactive, apparent partial and total values Programmable tariff functions Hour counter for programmable total and partial hours Pulse counter for general use: consumption pulse counting for water, gas, etc., with expansion module. ational characteristics uxiliary supply voltage range: 100...440VC / 110...250VC for MG 700/800 12--48VC for MG 800 048 Voltage measurement range: 20...830VC - Usage in medium and high voltage systems with voltage transformers Rated input current: by external CT 5 for MG 700; by external CT 5 or 1 for MG 800 Frequency measurement range 45...66Hz True RMS measurements: for voltage and current Measurement accuracy for MG 700: Voltage: ±0,5% Current: ±0,5% (0,1...1,1In) Power: ±1% f.s. Frequency: ±0,05% ctive energy: Class 1 (IEC/E 62053-21) Reactive energy: Class 2 (IEC/E 62053-23) Measurement accuracy for MG 800..: Voltage: ±0,2% (50...830VC) Current: ±0,2% (0,1...1,1In) Power: ±0,5% f.s. Power factor: ±0,5% Frequency: ±0,05% ctive energy: Class 0,5s (IEC/E 62053-22) Reactive energy: Class 2 (IEC/E 62053-23) on-volatile memory for data storage Communication protocol Modbus-RTU, SCII and TCP Compatible with and software Flush-mount housing 96x96mm/3.78 x3.78 E degree of protection: IP65 on front; IP20 at terminals. suvision and energy management software See Section 29. configuration and remote control software See Section 29. EXM series expansion modules See page 30-2. Certifications and compliance Certifications obtained: EC and RCM for all; U listed for US and Canada (cuus File E93601), as uxiliary evices Multimeters. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-4, U 61010-1, U508, CS C22.2 n 14. -18 Software and accessories pages -27 and 28 Expansion modules page 30-2 imensions page -32 Wiring diagrams page -36 page -43
igital metering instruments Flush-mount C touchscreen power analyzers, expandable MG 900... MG M3 900 01 MG 900T... MG 900R EXP10... rder escription Qty Wt code pkg. n [kg] MG 900 Graphic 128x112 pixel 1 0.566 touch-screen C, harmonic analysis, 4 current channels, (neutral meas.), 100...440VC/110...250VC. Multilanguage: Italian, English, French, Spanish and Portuguese MG 900 01 Graphic 128x112 pixel 1 0.566 touch-screen C, harmonic analysis, 4 current channels, (neutral meas.), 100...440VC/110...250VC. Multilanguage: English, Czech, Polish, German and Russian MG 900 048 Graphic 128x112 pixel 1 0.580 touch-screen C, harmonic analysis, 4 current channels, auxiliary supply 12--48VC MG M3 900 01 MG 900 portable unit in 1 3.400 M3 case, prewired for mobile applications, with USB port, without external cables (see page -28) MG 900T Measurement transducer, 1 0.570 harmonic analysis, 4 current channels (neutral meas.), 100...440VC/110...250VC, RS232 and RS485 ports ❶ MG 900T 048 Measurement transducer, 1 0.590 harmonic analysis, 4 current channels (neutral meas.), 12--48VC, RS232 and RS485 ports ❶ Remote display for MG 900T... MG 900R Graphic 128x112 pixel 1 0.396 touch-screen C, with 3m long connecting cable❷ ❶ o simultaneous oations of serial ports. Consult Technical support for information (Tel. 035 42822; E-mail: service@ovatoelectric.com) or the instructions manual. ❷ irect link to MG 900T dedicated port: powered directly by MG 900T. rder escription code MG 900 and MG 900 T EXPSI MUES. Inputs and outputs. EXP10 00 EXP10 01 EXP10 02 EXP10 03 EXP10 04 EXP10 05 4 opto-isolated digital inputs 4 opto-isolated static outputs 2 digital inputs and 2 static outputs, opto-isolated 2 relay outputs rated 5 250VC 2 opto-isolated analog inputs 0/4-20m or PT100 or 0-10V or 0...±5V 2 opto-isolated analog outputs 0/4-20m or 0-10V or 0...±5V EXP10 08 2 opto-isolated digital inputs and 2 relay outputs rated 5 250VC Communication ports. EXP10 10 EXP10 11 EXP10 12 EXP10 13 EXP10 14 EXP10 15 EXP10 30 pto-isolated USB interface pto-isolated RS232 interface pto-isolated RS485 interface pto-isolated Ethernet interface with Web server function pto-isolated Profibus-P interface GPRS/GSM modem, without antenna ata storage, clock-calendar (RTC) with backup reserve energy for data logging EXP10 31 ata storage, with Energy Quality (E 50160 - class B), clock-calendar (RTC) with backup reserve energy for data logging MG 900... expandable digital power analyzers are available with a flush-mount housing, 96x96mm/3.78 x3.78. The wide graphic touch-screen display provides extremely simple interacting between the device and the user. The high formance of the power analyzers gives very accurate measurements and can control energy distribution networks, to detect and prevent energy problems which could compromise quality and supply. The main features include an extensive power supply voltage range, high measurement accuracy, expandability up to 4 plug-in expansion modules. There also is available the MG 900T measurement transducer which can be used with the MG 900R remote display. The MG 900T, without display, is arranged for mounting inside the panel board, on 35mm I rail, and is an ideal solution for installations where the measurements of various multimeters must be remotely viewed. The MG 900R remote display connected to the MG 900T transducer can display the measurements on the panel front. Main measurements and functions include: Voltage: phase, phase-neutral and ground neutral-earth Supply voltage value (only MG... 048) Current: phase values eutral current calculated and true values Power: apparent, active and reactive phase and total values P.F.: Power Factor phase and total Cos phase Frequency of measured voltage value Voltage and current asymmetry Total harmonic distortion (TH) of voltage and current Harmonic analysis of voltage and current up to the 63 order HIGH-W-VERGE value functions for all measurements Maximum demand of power and current values Energy meters for active, reactive, apparent partial and total values with programmable tariff functions Hour counter for programmable total and partial hours Pulse counter for general use: consumption pulse counting for water, gas, etc., with expansion module only Energy quality analysis to E 50160 Class B (with expansion module). ational characteristics uxiliary supply voltage range: 110...440VC / 110...250VC for MG 900 and MG 900T; 12--48VC for MG 900 048 and MG 900T 048 Voltage measurement range: 20...830VC phase-to-phase 10...480VC phase-neutral Usage in medium and high-voltage systems with voltage transformers rated input current: 5 or 1 via CT Current measurement range: 0.05...10 o 0.01...1.2 Current measurements via CT up to 10,000 Frequency measurement range: 45...66Hz / 360...440Hz True RMS measurements for voltage and current values ccuracy: Voltage: ±0.2% (50...830VC) Current: ±0.2% (0.1...1.1In) Power: ±0.5% f.s. Power factor: ±0.5% Frequency: ±0.05% ctive energy: Class 0.5s (IEC/E 62053-22) Reactive energy: Class 2 (IEC/E 62053-23) on-volatile memory for data and event (last 100) storage Communication protocol Modbus-RTU, SCII and TCP with communication expansion modules only Programming and remote control by software with communication expansion modules only Housing: 96x96mm/3.78 x3.78 flush-mount (for MG 900... and MG 900R) and 35mm I rail (for MG 900T...) E degree of protection: IP65 on front for MG 900 - MG 900R; IP20 at terminals for MG 900 - MG 900T. suvision and energy management software See Section 29. configuration and remote control software See Section 29. EXM series expansion modules See page 30-2. Certifications and compliance Certifications obtained: EC and RCM for all except MG M3...; U isted, for US and Canada (cuus - File E93601), as uxiliary evices-multimeters for all except MG M3... Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-4, U 508, CS C22.2 n 14. Software and accessories pages -27 and 28 Expansion modules page 30-2 imensions page -32 Wiring diagrams page -36 page -43-19
igital metering instruments Flush-mount E instruments single-phase, non expandable MK 0... rder isplayed Relay Qty Wt code measurements output pkg n n n [kg] Voltmeter. MK 00 1 voltage value 1 0.290 MK 00 R1❷ 1 max voltage value 1 min voltage value 1 1 0.323 mmeter. MK 01 1 current value 1 0.290 MK 01 R1❷ 1 max current value 1 min current value 1 1 0.323 Voltmeter or ammeter. MK 02❶ 1 voltage or 1 0.290 current value 1 maximum voltage or current value 1 minimum voltage or current value Frequency meter. MK 03 R1❷ 1 frequency value 1 1 0.323 1 max frequency value 1 min frequency value Cos meter. MK 04 R1❷ 1 cos value 1 1 0.290 1 power factor value ❶ The MK02 can oate as a voltmeter or ammeter. It is duly equipped with two front plates (V and ) which must be fitted by the user depending on which instrument is required and on the wiring scheme used. ❷ Relay output for control and protection functions. The MK 0... instruments are available with flush-mount housing, 96x48mm/3.78x1.89. Measurements are True RMS values and provide for reliable oation even in the presence of harmonics. ational characteristics uxiliary supply voltage: 220-0VC; ating frequency: 50-60Hz True RMS measurements Max. and min. measurement storage 1 relay output with 1 changeover contact (for MK...R1 only) Housing: flush-mount 96x48mm/3.78x1.89 Terminals: 4mm 2 egree of protection: IP54 on front; IP20 at terminals. MK 00 - MK 00 R1 Voltage measurement range: 15-660VC ating frequency range: 45-65Hz Programmable VT ratio: 1.00-500.00 ccuracy: ±0.25% f.s. ±1 digit MK 01 - MK 01 R1 Current measurement range: 0.05-5.75 ating frequency range: 45-65Hz Programmable CT ratio: 5-10,000 ccuracy: ±0.5% f.s. ±1 digit MK 02 Voltage measurement range: 15-660VC Current measurement range: 0.05-5.75 ating frequency range: 45-65Hz Programmable VT ratio: 1.00-500.00 Programmable CT ratio: FF/5-10,000 ccuracy: Voltage ±0.25% f.s. ±1 digit Current ±0.5% f.s. ±1 digit MK 03 R1 Measurement input: 15-660VC Frequency measurement range: 15-65Hz ccuracy: ±1 digit MK 04 R1 Cos measurement error: ±0.5 ±1 digit Cos measurement in 4 quadrants ccuracy: ±1 ±1 digit Control and protection functions MK 00 R1 Voltage loss or failure: FF/5-85% Maximum voltage: FF/102-120% Minimum voltage: FF/70-98% Time delay for max-min voltage or voltage loss❸: 0.0-900.0 seconds. MK 01 R1 Current loss: FF/2-100% Maximum current: FF/102-200% Maximum current instantaneous tripping: FF/110-600% Minimum current: FF/5-98% Time delay for max-min current or current loss❸: 0.0-900.0 seconds. MK 03 R1 Maximum frequency: FF/101-110% Minimum frequency: FF/90-99% Time delay for min-max frequency ❸: 0.5-900.0 seconds. MK 04 R1 Minimum-maximum cos thresholds in 4 quadrants Minimum-maximum PF thresholds in 4 quadrants elay time for max or min threshold ❸: 1-9,000 seconds. Certifications and compliance Certifications obtained: EC; U isted, for US and Canada (cuus - File E93601), as uxiliary evices-multimeters. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-3, U508, CS C22.2 n 14. ❸ Independent adjustable delays. -20 ccessories page -27 imensions page -32 Wiring diagrams page -37 pages -44 and 45
igital metering instruments Flush-mount E instruments three-phase, non expandable MK 1... rder isplayed Relay Qty Wt code measurements output pkg n n n [kg] Voltmeter. MK 10 3 phase voltage values 1 0.297 MK 10 R1❷ 3 phase to phase voltage values 1 1 0.330 3 maximum phase voltage values 3 maximum phase to phase voltage values 3 minimum phase voltage values 3 minimum phase to phase voltage values mmeter. MK 11 3 phase current values 1 0.292 MK 11 R1❷ 3 maximum phase current values 1 1 0.336 3 minimum phase current values Voltmeter, ammeter and wattmeter. MK 15 3 phase voltage values 1 0.332 MK 15 R1❶❷ 3 phase to phase voltage values 1 1 0.350 3 phase current values 4 active power values, phase and total 3 maximum phase voltage values 3 maximum phase to phase voltage values 3 maximum phase current values 4 maximum active power values, phase and total 3 minimum phase voltage values 3 minimum phase to phase voltage values 3 minimum phase current values 4 minimum active power values, phase and total ❶ Connection also to single-phase. ❷ Relay output for control and protection functions. The MK 1... instruments are available with flush-mount housing, 96x48mm/3.78x1.89. Measurements are True RMS values and provide for reliable oation even in the presence of harmonics. ational characteristics uxiliary supply voltage: 220-0VC; ating frequency: 50-60Hz True RMS measurements Max and min measurement storage 1 relay output with 1 changeover contact (for MK...R1 only) Housing: flush-mount 96x48mm/3.78x1.89 Terminals: 4mm 2 egree of protection: IP54 on front; IP20 at terminals. MK 10 - MK 10 R1 Voltage measurement range: 15-660VC ating frequency range: 45-65Hz Programmable VT ratio: 1.00-500.00 ccuracy: ±0.25% f.s. ±1 digit. MK 11 - MK 11 R1 Current measurement range: 0.05-5.75 ating frequency range: 45-65Hz Programmable CT ratio: 5-10,000 ccuracy: ±0.5% f.s. ±1 digit. MK 15 - MK 15 R1 Voltage measurement range: 35-660VC Current measurement range: 0.05-5.75 Frequency measure range: 45-65Hz Programmable VT ratio: 1.00-500.00 Programmable CT ratio: 5-10,000 ccuracy: Voltage ±0.25% f.s. ±1 digit Current ±0.5% f.s. ±1 digit Power ±1% f.s. ±1 digit. Control and protection functions MK 10 R1 Phase loss or failure: FF/5-85% Maximum voltage: FF/102-120% Minimum voltage: FF/70-98% symmetry: FF/2-20% Phase sequence: FF/1-2-3/3-2-1 Frequency Maximum frequency: FF/101-110% Minimum frequency: FF/90-99% Time delay for max-min voltage, phase loss, asymmetry and min-max frequency ❸: 0.5-900.0 seconds. MK 11 R1 Current loss: FF/2-100% Maximum current: FF/102-200% Maximum current instantaneous tripping: FF/110-600% Minimum current: FF/5-98% symmetry: FF/2-20% Time delay for max-min current or current loss and asymmetry ❸: 0.5-900.0 seconds. MK 15 R1 Voltage Phase loss or failure: FF/5-85% Maximum voltage: FF/102-120% Minimum voltage: FF/70-98% symmetry: FF/2-20% Phase sequence: FF/1-2-3/3-2-1 Current Current loss: FF/5-85% Maximum current: FF/102-200% Maximum current instantaneous tripping: FF/110-600% Minimum current: FF/5-98% symmetry: FF/2-20% Power Rated power: 1-10,000 Maximum power: FF/101-200% Max. power instantaneous tripping: FF/110-600% Minimum power: FF/10-99% Frequency Maximum frequency: FF/101-110% Minimum frequency FF/90-99% Time delay for max-min voltage, max-min current or current loss, phase loss, asymmetry and min-max power ❸: 0.0-900.0 seconds. Certifications and compliance Certifications obtained: EC; U isted, for US and Canada (cuus - File E93601), as uxiliary evices-multimeters. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-3, U 508, CS C22.2 n 14. ❸ Independent adjustable delays. ccessories page -27 imensions page -32 Wiring diagrams page -37 page -46-21
igital metering instruments Flush-mount E multimeter three-phase, non expandable MK 16 rder isplayed Qty Wt code measurements pkg n [kg] MK 16 3 phase voltage values 1 0.350 3 phase to phase voltage values 3 phase current values 4 active power values, phase and total 4 reactive power values, phase and total 4 apparent power values, phase and total 3 phase power factor values 1 frequency value 1 active energy value in kwh 1 reactive energy value in kvarh 1 hour counter 3 maximum phase voltage values 3 maximum phase to phase voltage values 3 maximum phase current values 4 maximum active power values, phase and total 4 maximum reactive power values, phase and total 4 maximum apparent power values, phase and total 3 minimum phase voltage values 3 minimum phase to phase voltage values 3 minimum phase current values 4 minimum active power values, phase and total 4 minimum reactive power values, phase and total 4 minimum apparent power values, phase and total The MK 16 multimeter is available with flush-mount housing, 96x48mm/3.78x1.89. Measurements are True RMS values and provide for reliable oation even in the presence of harmonics. ational characteristics uxiliary supply voltage: 220-0VC ating frequency: 50-60Hz True RMS measurements ccuracy: Voltage ±0.25% f.s. ±1 digit Current ±0.5% f.s. ±1 digit ctive energy accuracy: Class 2 (IEC/E 62053-21 and IEC/E 62053-23) Max and min measurement storage Voltage measurement range: 35-660VC Current measurement range: 0.05-5.75 ating frequency range: 45-65Hz Programmable VT ratio: 1.00-500.0 Programmable CT ratio: 5-10,000 Housing: flush-mount 96x48mm/3.78x1.89 Terminals: 4mm 2 E degree of protection: IP54 on front; IP20 at terminals. Certifications and compliance Certifications obtained: EC; U isted, for US and Canada (cuus - File E93601), as uxiliary evices-multimeters. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-3, U508, CS C22.2 n 14. -22 ccessories page -27 imensions page -32 Wiring diagrams page -37 page -46
igital metering instruments Flush-mount E multimeter three-phase, non expandable MK 16 R1 rder isplayed Relay Qty Wt code measurements output pkg n n n [kg] MK 16 R1 ❶ 3 phase voltage values 1 1 0.353 3 phase to phase voltage values 3 phase current values 4 active power values, phase and total 4 reactive power values, phase and total 4 apparent power values, phase and total 3 phase power factor values 1 frequency value 1 active energy value in kwh 1 reactive energy value in kvarh 1 hour counter 3 maximum phase voltage values 3 maximum phase to phase voltage values 3 maximum phase current values 4 maximum active power values, phase and total 4 maximum reactive power values, phase and total 4 maximum apparent power values, phase and total 3 minimum phase voltage values 3 minimum phase to phase voltage values 3 minimum phase current values 4 minimum active power values, phase and total 4 minimum reactive power values, phase and total 4 minimum apparent power values, phase and total 2 minimum and maximum power factor values ❶ Connection also to single-phase. The MK 16 R1 multimeter is available with flush-mount housing, 96x48mm/3.78x1.89 Measurements are True RMS values and provide for reliable oation even in the presence of harmonics. ational characteristics uxiliary supply voltage: 220-0VC ating frequency: 50-60Hz True RMS measurements ccuracy: Voltage ±0.25% f.s. ±1 digit Current ±0.5% f.s. ±1 digit ctive energy accuracy: Class 2 (IEC/E 62053-21 and IEC/E 62053-23) Max and min measurement storage Voltage measurement range: 35-660VC Current measurement range: 0.05-5.75 Frequency measurement range: 45-65Hz Programmable VT ratio: 1.00-500.0 Programmable CT ratio: 5-10,000 1 relay output with 1 changeover (SPT) contact Housing: flush-mount 96x48mm/3.78x1.89 Terminals: 4mm 2 E degree of protection: IP54 on front; IP20 at terminals. PRGRMMBE REY UTPUT Voltage Phase loss or failure: FF/5-85% Maximum voltage: FF/102-120% Minimum voltage: FF/70-98% symmetry: FF/2-20% Phase sequence: FF/1-2-3/3-2-1 Current Protection inhibition max current: FF/2-100% Maximum current: FF/102-200% Maximum current instantaneous tripping: FF/110-600% Minimum current: FF/5-98% symmetry: FF/2-20% Power factor Maximum power factor: 0.10-1.00 Minimum power factor: 0.10-1.00 Time delay for max-min voltage, max-min current or current loss, phase loss, asymmetry and min-max power factor ❷: 0.0-900.0 seconds. Certifications and compliance Certifications obtained: EC; U isted, for US and Canada (cuus - File E93601), as uxiliary evices-multimeters. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6- 2, IEC/E 61000-6-3, U508, CS C22.2 n 14. ❷ Independent adjustable delays. ccessories page -27 imensions page -32 Wiring diagrams page -37 page -46-23
igital metering instruments Flush-mount E multimeters, non expandable 47 electrical parameters MK 2... rder code escription Qty Wt pkg. n [kg] MK 20 Basic version, auxiliary 1 0.434 supply 208...0VC MK 22 Version with energy 1 0.477 meters and RS485 port included, auxiliary supply 208...0VC MK 2... digital multimeters are available with flush-mount housing, 96x96mm/3.78x3.78. They monitor and view reliable readings of electrical parameters, even in the presence of critical oating conditions, such as voltages and currents with high harmonic content and variable frequency. The total and partial hour counter provides an interesting feature for electric panels of emergency generating sets. The diversified and accurate measurements give the multimeters valuable technical and cost effective advantages with respect to traditional analog instrumentation. MK2... digital multimeters view 47 electrical parameters: Voltage: phase, line and system values Current: phase values Power: active and reactive values, apparent phase. P.F.: power factor phase Frequency (measured voltage frequency) HIGH/W: instantaneous minimum and maximum values of each phase voltage and current, total active power ( W), total reactive power ( var) and total apparent power ( V) values Total hours: non-volatile clearable log for MK 20 Partial hours: non-volatile configurable log for MK 20 ctive and reactive energy meters for MK22 only. ational characteristics uxiliary supply voltage range: 154-288VC for MK 20 177-264VC for MK 22 Voltage measurement range: 60-830VC phase-phase 30-480VC phase-neutral Current measurement range: 0.05-6 Frequency measurement range: 45-65Hz Programmable CT ratio: 1.0-2,000 Voltage accuracy: Class 0.5 ±0.35% f.s. (830V) Current accuracy: Class 0.5 ±0.5% f.s. (6) ctive energy accuracy: Class 2 Total and partial hour counter (can be used as maintenance with optical alarm and separate resetting) (MK 20) HIGH and W value functions to read and log instantaneous voltage, current and power values elayed automatic resetting of default measurements veraging function to slow down repetitive fluctuations to obtain more stable readouts Current connection in R configuration by 2 current transformers (CTs) only Single, two, three-phase, with or without neutral, True RMS measurements RS485 serial port, compatible with software for MK 22 Housing: flush-mount 96x96mm/3.78x3.78 E degree of protection: IP54 on front; IP20 at terminals. suvision and energy management software See Section 29. Certifications and compliance Certifications obtained: EC; U isted, for US and Canada (cuus - File E93601), as uxiliary evices-multimeters. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-3, U508, CS C22.2 n 14. - Software and accessories page -27 imensions page -32 Wiring diagrams page -37 page -47
igital metering instruments Modular E instruments single-phase, non expandable MK 80 MK 81 MK 80 R1 MK 81 R1 MK 82 MK 82 rder isplayed Relay Qty Wt code measurements output pkg n n n [kg] Voltmeter. MK 80 1 voltage value 1 0.237 MK 80 R1❷ 1 max voltage value 1 min voltage value 1 1 0.268 mmeter. MK 81 1 current value 1 0.237 MK 81 R1❷ 1 max current value 1 min current value 1 1 0.268 Voltmeter or ammeter. MK 82❶ 1 voltage or current 1 0.1 value 1 maximum voltage or current value 1 minimum voltage or current value Frequency meter. MK 83 R1❷ 1 frequency value 1 1 0.268 1 max frequency value 1 min frequency value Cos meter. MK 84 R1❷ 1 cos value 1 1 0.272 1 power factor value ❶ The MK82 can oate as a voltmeter or ammeter. It is duly equipped with two front plates (V and ) which must be fitted by the user depending on which instrument is required and on the wiring scheme used. ❷ Relay output with control and protection functions. The MK 8... instruments are available with modular housing, 3 module size. Measurements are True RMS values and provide for reliable oation even in the presence of harmonics. ational characteristics uxiliary supply voltage: 220-0VC ating frequency: 50-60Hz True RMS measurements Max and min measurement storage 1 relay output with 1 changeover contact (SPT) for MK...R1 version only Modular I 43880 housing, 3 modules Terminals: 4mm 2 E degree of protection: IP40 on front; IP20 on terminals. MK 80 - MK 80 R1 Voltage measurement range: 15-660VC ating frequency range: 45-65Hz Programmable VT ratio: 1.00-500.00 ccuracy: ±0.25% f.s. ±1 digit MK 81 - MK 81 R1 Current measurement range: 0.05-5.75 ating frequency range: 45-65Hz Programmable CT ratio: 5-10,000 ccuracy: ±0.5% f.s. ±1 digit MK 82 Voltage measurement range: 15-660VC Current measurement range: 0.05-5.75 ating frequency range: 45-65Hz Programmable VT ratio: 1.00-500.00 Programmable CT ratio: FF/5-10,000 ccuracy: Voltage ±0.25% f.s. ±1 digit ccuracy: Current ±0.5% f.s. ±1 digit MK 83 R1 Measurement input: 15-660VC Frequency measurement range: 50-60Hz ±10% Measurement accuracy: ±1 digit ccuracy: ±1 digit MK 84 R1 Cos measurement error: ±0.5 ±1 digit Cos measurement in 4 quadrants ccuracy: ±1 ±1 digit MK 83 MK 83 R1 Control and protection functions MK 80 R1 Voltage loss or failure: FF/5-85% Maximum voltage: FF/102-120% Minimum voltage: FF/70-98% Time delay for max-min voltage or voltage loss ❸: 0.0-900.0 seconds. MK 81 R1 Current loss: FF/2-100% Maximum current: FF/102-200% Maximum current instantaneous tripping: FF/110-600% Minimum current: FF/5-98% Time delay for max-min current or current loss ❸: 0.0-900.0 seconds. MK 84 MK 84 R1 MK 83 R1 Maximum frequency: FF/101-110% Minimum frequency: FF/90-99% Time delay for min-max frequency ❸: 0.5-900.0 seconds. MK 84 R1 Minimum-maximum cos thresholds in 4 quadrants Minimum-maximum PF thresholds in 4 quadrants elay time for max or min threshold ❸: 1-9,000 seconds. Certifications and compliance Certifications obtained: EC. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-3. ❸ Independent adjustable delays. imensions page -33 Wiring diagrams page -37 pages -44 and 45-25
igital metering instruments Modular E instruments three-phase, non expandable MK 70 MK 71 MK 75 MK 70 R1 MK 71 R1 MK 75 R1 rder isplayed Relay Qty Wt code measurements output pkg n n n [kg] Voltmeter. MK 70 3 phase voltage values 1 0.233 MK 70 R1❷ 3 phase to phase voltage values 1 1 0.264 3 max phase voltage values 3 max phase to phase voltage values 3 min phase voltage values 3 min phase to phase voltage values mmeter. MK 71 3 phase current values 1 0.1 MK 71 R1❷ 3 max phase current values 1 1 0.272 3 min phase current values Combined voltmeter, ammeter and wattmeter. MK 75 3 phase voltage values 1 0.271 MK 75 R1❶❷ 3 phase to phase voltage values 1 1 0.280 3 phase current values 4 active power values, phase and total 3 maximum phase voltage values 3 maximum phase to phase voltage values 3 maximum phase current values 4 max active power, phase and total 3 minimum phase voltage values 3 minimum phase to phase voltage values 3 minimum phase current values 4 min active power, phase and total ❶ Connection also to single-phase. ❷ Relay output with control and protection functions. The MK 7... instruments are available with modular housing, 3 module size. Measurements are True RMS values and provide for reliable oation even in the presence of harmonics. ational characteristics uxiliary supply voltage: 220-0VC ating frequency: 50-60Hz True RMS measurements Max and min measurement storage 1 relay output with 1 changeover contact (SPT) for MK...R1 version only Modular I 43880 housing, 3 module Terminals: 4mm 2 E degree of protection: IP40 on front; IP20 on terminals. MK 70 - MK 70 R1 Voltage measurement range: 15-660VC ating frequency range: 45-65Hz Programmable VT ratio: 1.00-500.00 ccuracy: ±0.25% f.s. ±1 digit MK 71 - MK 71 R1 Current measurement range: 0.05-5.75 ating frequency range: 45-65Hz Programmable CT ratio: 5-10,000 ccuracy: ±0.5% f.s. ±1 digit MK 75 - MK 75 R1 Voltage measurement range: 35-660VC Current measurement range: 0.05-5.75 Frequency measure range: 45-65Hz Programmable VT ratio: 1.00-500.00 Programmable CT ratio: 5-10,000 ccuracy: Voltage ±0.25% f.s. ±1 digit ccuracy: Current ±0.5% f.s. ±1 digit Control and protection functions MK 70 R1 Phase loss or failure: FF/5-85% Maximum voltage: FF/102-120% Minimum voltage: FF/70-98% symmetry: FF/2-20% Phase sequence: FF/1-2-3/3-2-1 Maximum frequency: FF/101-110% Minimum frequency: FF/90-99% Time delay for max-min voltage, phase loss, asymmetry and min-max frequency ❸: 0.0-900.0 seconds. MK 71 R1 Current loss: FF/2-100% Maximum current: FF/102-200% Maximum current instantaneous tripping: FF/110-600% Minimum current: FF/5-98% symmetry: FF/2-20% Time delay for max-min current or current loss and asymmetry ❸: 0.0-900.0 seconds. MK 75 R1 Voltage Phase loss or failure: FF/5-85% Maximum voltage: FF/102-120% Minimum voltage: FF/70-98% symmetry: FF/2-20% Phase sequence: FF/1-2-3/3-2-1 Current Current loss: FF/2-100% Maximum current: FF/102-200% Maximum current instantaneous tripping: FF/110-600% Minimum current: FF/5-98% symmetry: FF/2-20% Power Rated power: 1-10,000 Maximum power: FF/101-200% Maximum power instantaneous tripping: FF/110-600% Minimum power: FF/10-99% Frequency Maximum frequency: FF/101-110% Minimum frequency: FF/90-99% Time delay for max-min voltage, max-min current or current loss, phase loss, asymmetry and min-max power ❸: 0.0-900.0 seconds. Certifications and compliance Certifications obtained: EC. Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-3. ❸ Independent adjustable delays. -26 imensions page -33 Wiring diagrams page -37 page -46
ccessories for metering instruments Communication devices rder code escription Qty Wt pkg CX 01 CX 02 n [kg] CX 01 USB/optical dongle with 1 0.090 PC VT Electric product connecting cable, for programming, data download, diagnostics and firmware upgrade CX 02 Wi-Fi dongle for PC VT 1 0.090 Electric product programming, data download, diagnostics and cloning CX 03 GSM/GPRS penta-band antenna 1 0.090 (850/900/1800/1900/2100Mhz) for EXP1015 expansion module Communication devices for connection of VT Electric products to sonal computers, smartphones and tablets. CX 01 The USB/optical dongle, complete with cable, allows the connection of products compatible with PCs without having to disconnect the power supply from the electric panel. The PC identifies the connection as a standard USB. CX 02 By Wi-Fi connection, compatible VT Electric products can be viewed on PCs, smartphones and tablets with no need for cabling. CX 03 ntenna compatible with the major part of worldwide mobile networks thanks to the available frequencies at 850/900/1800/1900/2100MHz. egree of protection: IP67. Fixing by Ø10mm drilling. Cable length: 2.5mm For dimensions, wiring schemes and technical characteristics, refer to technical instructions in the ownloads section at: www.ovatoelectric.com CX 03 Protection covers rder code escription Qty Wt pkg n [kg] P 96X48 Front protection cover, IEC IP65 1 0.048 for MK 0/1... 31 P 96X96 Front protection cover, IEC IP54 1 0.077 for MK 2... When a higher front IP protection degree is needed, the covers can be installed on the corresponding devices and also provide a sealing feature. 31 P96x96 ccessories rder code escription Qty Wt pkg n [kg] EXP80 00 EXP80 00 Plastic insert for customising 10 0.005 label fixing for MG 600/610/611... EXM80 04 Set of sealable terminal covers 1 0.020 for MG 100/110/200/210/300-27
ccessories for metering instruments Converter rder code escription Qty Wt pkg. n [kg] EXC C 01 EXC C 01 RS485/Ethernet 12...48VC 1 0.400 converter, including I rail fixing kit The EXC C 01 converter allows Slave devices connected on an RS485 network to interface with a Master featuring Ethernet port: kit comprising converter and I rail mounting accessory; programming via web interface; power supply not included. Certifications Certifications obtained: cuus (U 60950-1) isted Fcc CSS. Gateway rder escription Qty Wt code pkg n [kg] EXC M3G 01 EXC G 01 EXC G X1 Connecting cables rder code escription Qty Wt pkg. 51 C4 MG M3 KIT... new EXC M3G 01 RS485 Gateway/3G modem, 1 0.340 9.5...27VC/9.5...35VC, including antenna and programming cables EXC G 01 Gateway data logger for the data 1 0.6 collecting via Modbus from the device in the field. Publishing of the data to suvision software, also in Cloud EXC G X1 2G/3G modem communication 1 module for EXC G 01 n [kg] 51 C2 For PC-multimeter 1 0.090 RS232 port, 1.8m long 51 C4 For PC-4 PX1 1 0.147 converter drive, 1.8m long 51 C5 For analog modem-multimeter 1 0.111 RS232 port, 1.8m long 51 C9 For 4PX 1 converter 1 0.137 drive-analog modem, 1.8m long Current clamp kits for MG M3. portable devices MG M3 KIT01 Composed of 3 current clamps 1 6.900 1000/1 and 4 alligator clip cables for voltage measurements MG M3 KIT02 Composed of 1 current clamps 1 0.860 1000/1 and 1 alligator clip cable for voltage measurements. For MGM3900, if measuring inputs for neutral-earth/ground and neutral current are used too EXC M3G 01 general characteristics The EXC M3G 01 gateway allows Slave devices connected on an RS485 network to interface with a Master via 3G network: TCP server connection via 3G or 2G network; Transparent oating mode: the data is transferred from 3G side to serial side and vice versa without protocol conversion; Settable parameters: TCP server IP and remote port, network oator apn (with username and password), SIM card pin (with enabling), connection time-out, serial parameters (baud rate from 1,200 bps to 115,200 bps, stop bit, character length, parity) RJ45 port for parameter programming and diagnosis with a simple software application. Compatible with major worldwide mobile phone networks, thanks to the use of 850/900/1800/1900/2100MHz frequencies Protection rating IP67 Fixing hole Ø10mm. Cable length 2.5m. Reference standards Compliant with standards: E 60950-1. EXC G 01 general characteristics EXC G 01 gateway is able to collect data from devices which are connected through ethernet or RS485 port. Modbus RTU, SCII and TCP protocols are supported. The data can be reviewed by a connection to Synergy Cloud service or to ethernet local web server and a browser. The access to internet for data sending can be achieved with ethernet port or by adding EXC G X1 2G/3G modem. CPU RM 1 GHz 2 ethernet port 1 RS232/RS422/RS485 serial port VC (10 32VC) power supply ating temature -20 +60 C Simplified connection to ovato Electric devices Compatible with and software. Reference standards Compliant with standards: emissions E 61000-6-4, immunity E61000-6-2, for installation in industrial environment. CECTIG CBES 51 C To connect energy meters and/or multimeters with: Personal computers Modems Bus converters. Electrical safety for MG M3 KIT... (IEC/E 61010-1 and IEC/E 611-2-032) CURRET CMPS 600V category III 300V category IV. VTGE MESURIG CBES 1000V category III. Reference standards Compliant with standards: IEC/E 61010-1, IEC/E 61000-6-2, IEC/E 61000-6-3. For dimensions, wiring schemes and technical characteristics, refer to technical instructions in ownloads at www.ovatoelectric.com. -28
Current transformers Solid-core M0T... M2T... M3T... M35T... M4T... rder code Primary Burden Qty Weight current Ipn cl. 0.5 cl. 1 pkg. /5 [] [V] [V] n [kg] For Ø22mm/0.87 cable. M0T 0050 50 1.25 1 0.200 M0T 0060 60 1.5 1 0.200 M0T 0080 80 1.5 1 0.200 M0T 0100 100 1.5 1 0.200 M0T 0150 150 2 1 0.200 For Ø23mm/0.90 cable. For 30x10mm/1.18x0.39, 25x12.5mm/0.98x0.49, 20x15mm/0.79x0.59 busbars. M2T 0100 100 1 1 0.130 M2T 0150 150 1.5 1 0.130 M2T 0200 200 2 1 0.130 M2T 0250 250 2.5 1 0.130 M2T 0300 300 1.5 3 1 0.130 M2T 0400 400 2 3 1 0.130 For Ø30mm/1.18 cable. For 40x10mm1.57x0.39, 30x20mm/1.18x0.79, 25x25mm/0.98x0.98 busbars. M3T 0200 200 5 1 0.260 M3T 0250 250 5 1 0.260 M3T 0300 300 2.5 5 1 0.260 M3T 0400 400 2.5 5 1 0.260 M3T 0500 500 2.5 5 1 0.260 M3T 0600 600 5 10 1 0.260 M3T 0800 800 5 10 1 0.260 For Ø66mm/2.60 cable. For 80x12,5mm/3.15 x0.49, 60x30mm/2.36x1.18, 50x50mm/1.97x1.97 busbars. M35T 0800 800 10 15 1 0.460 M35T 1000 1000 15 20 1 0.460 M35T 1250 1250 15 20 1 0.460 For Ø86mm/3.38 cable. For 100x30mm/3.94x1.18, 80x50mm/3.15x1,97, 70x60mm/2.75x2.36 busbars. M4T 1000 1000 10 20 1 0.700 M4T 1250 1250 15 30 1 0.760 M4T 1500 1500 20 30 1 0.760 M4T 1600 1600 20 30 1 0.800 M4T 2000 2000 30 45 1 0.840 M4T 2500 2500 35 45 1 0.900 M4T 3000 3000 45 45 1 0.900 M4T 3500 3500 50 50 1 0.900 M4T 4000 4000 50 50 1 0.900 The current transformers (CTs) in the M series are installed in an electrical system to reduce the line current to a secondary value of 5 compatible with the ammeter inputs of the digital multimeters or protection relays. M... are instrument transformers in class 1/0.5 without a primary winding and are normally used for high primary current values starting from 50. The number of loops of the primary cable does not modify the accuracy but converts the primary current value proportional to secondary current. 300/5 300/5 300/5 S1 K S1 K S1 K J-29 P1-K J-29 P1-K J-29 P1-K S2 300:n/5 300:1/5=300/5 S2 300:n/5 300:2/5=150/5 S2 300:n/5 300:3/5=100/5 n =1 300 / 5 standard 1 loop = 300 / 5 n =2 300 / 5 2 loops = 150 / 5 n =3 300 / 5 3 loops = 100 / 5 ational characteristics ating frequency: 50-60Hz Secondary output current: 5 verload withstand: 120% Ipn IEC rated insulation voltage Ui: 720V IEC rated short-time thermal current Ith: 40-60 Ipn for 1 second IEC rated dynamic current Idyn: 2.5 Ith for 1 second Insulation (dry type): Class E Terminals: Faston for M2T and M3T types Screw for M0T, M4T and M35T types Sealable terminal covers for M4T and M35T types Fixing on 35mm I rail (IEC/E 60715) or by screws (fixing elements standard supplied with the product) E degree of protection: IP30 mbient conditions: ating temature: -25...+50 C Storage temature: -40...+80 C Relative humidity, non condensing: 90%. Certifications and compliance Certifications obtained: EC. Compliant with standards: IEC/E 61869-2, IEC/E 61869-1. imensions page -33-29
Current transformers ccuracy solid-core M1TP... M3TP... M5TP... Version with UTF certificates. See page -13. rder code Primary Burden Qty Weight current Ipn cl. 0.5s cl. 0.5 pkg. /5 [] [V] [V] n [kg] For Ø28mm/1.10 ❶ cable. For 30x10mm/1.18x0.39, 25x12.5mm/0.98x0.49, 20x20mm/0.79x0.79 busbar. M1TP 0060 60 1.5 1.5 1 0.560 M1TP 0080 80 2,5 2,5 1 0.580 M1TP 0100 100 2.5 3.75 1 0.480 M1TP 0150 150 2.5 3.75 1 0.480 M1TP 0200 200 2.5 3.75 1 0.480 M1TP 0250 250 2.5 5 1 0.480 M1TP 0300 300 2.5 5 1 0.480 M1TP 0400❷ 400 5 5 1 0.480 M1TP 0500❷ 500 5 5 1 0.480 For Ø52mm/2.04 ❶ cable. For 60x20mm/2.36x0.79, 50x25mm/1.97x0.98 busbar. M3TP 0500 500 3.75 5 1 0.700 M3TP 0600 600 5 10 1 0.700 M3TP 0800 800 5 10 1 0.700 M3TP 1000 1000 5 10 1 0.700 For Ø85.5mm/3.37 ❶ cable. For 100x20mm/3.94x0.79, 80x45mm/3.15x1.77 busbar. M5TP 1000 1000 5 10 1 0.900 M5TP 1250 1250 7.5 10 1 0.900 M5TP 1600 1600 7.5 10 1 0.900 M5TP 2000 2000 10 15 1 0.900 M5TP 2500 2500 10 15 1 0.900 M5TP 3000 3000 10 15 1 0.900 ❶ Consult Technical support to inquiry about versions with Italian UTF certificates. ❷ For Ø33mm cable. For 40x10mm, 30x20mm, 25x25mm busbar. The M...TP type accuracy current transformers (CTs) are installed in an electrical system to reduce the line current to a secondary value of 5 compatible with the ammeter inputs of the digital multimeters or protection relays. M...TP are accuracy current transformers in class 0.5s without a primary winding and are normally used for high primary current values starting from 60. The number of loops of the primary cable does not modify the accuracy but converts the primary current value proportional to secondary current. 300/5 300:n/5 300:1/5=300/5 300/5 300:n/5 300:3/5=100/5 300/5 n=1 300 / 5 standard 1 loop = 300 / 5 n=2 300 / 5 2 loops = 150 / 5 n=3 300 / 5 3 loops = 100 / 5 300:n/5 300:3/5=100/5 ational characteristics ating frequency: 50-60Hz Secondary output current: 5 verload withstand: 120% Ipn IEC rated insulation voltage Ui: 720V IEC rated short-time thermal current Ith: 40-60 Ipn for 1 second IEC rated dynamic current Idyn: 2.5 Ith for 1 second Insulation (dry type): Class E Screw terminals Sealable terminal covers Fixing on 35mm I rail (IEC/E 60715) or by screws (fixing elements standard supplied with the product) E degree of protection: IP30 mbient conditions: ating temature: -25...+50 C Storage temature: -40...+80 C. Relative humidity, non condensing: 90%. Certifications and compliance Certifications obtained: EC. Compliant with standards: IEC/E 61869-2, IEC/E 61869-1. -30 imensions page -33
Current transformers Compact prewired split-core M1TM... rder code Primary Burden Qty Weight current Ipn cl. 0.5 cl. 1 pkg. /5 [] [V] [V] n [kg] xmm/0.94x0.94 hole. Cable supplied as standard, length 1m. M1TM 0100 100 1.2 1 0.200 M1TM 0150 150 1.2 1 0.200 M1TM 0200 200 1.2 1 0.200 M1TM 0250 250 1.2 1 0.200 36x38mm/1.42x1.50 hole. Cable supplied as standard, length 1m. M2TM 0250 250 1.5 1 0.380 M2TM 0300 300 1.5 1 0.380 M2TM 0400 400 1.5 1 0.380 M2TM 0500 500 1.5 1 0.380 The M...TM type current transformers (CTs) are installed in an electrical system to reduce the line current to a secondary value of 5 compatible with the ammeter inputs of the digital multimeters or protection relays. M...TM are instrument transformers in class 1 without a primary winding and are normally used for high primary current values starting from 100. ational characteristics ating frequency: 50-60Hz Secondary output current: 5 verload withstand: 120% Ipn IEC rated insulation voltage Ui: 720V IEC rated short-time thermal current Ith: 40-60 Ipn for 1 second IEC rated dynamic current Idyn: 2.5 Ith for 1 second Cable supplied as standard, length 1m. Insulation (dry type): Class E mbient conditions: ating temature: -25...+50 C Storage temature: -40...+80 C Relative humidity, non condensing: 90%. M2TM... Certifications and compliance Certifications obtained: EC. Compliant with standards: IEC/E 61869-2, IEC/E 61869-1. Split-core M1T... M2T... M3T... rder code Primary Burden Qty Weight current Ipn cl. 0.5 cl. 1 pkg. /5 [] [V] [V] n [kg] 50x80mm/1.97x3.15 hole. M1T 0250 250 1 2 1 0.900 M1T 0300 300 1.5 3 1 0.900 M1T 0400 400 1.5 3 1 0.900 M1T 0500 500 2.5 5 1 0.900 M1T 0600 600 2.5 5 1 0.900 M1T 0800 800 3 7.5 1 0.900 M1T 1000 1000 5 10 1 0.900 80x80mm/3.15x3.15 hole. M2T 0250 250 1 2 1 1.050 M2T 0300 300 1.5 3 1 1.050 M2T 0400 400 1.5 3 1 1.050 M2T 0500 500 2.5 5 1 1.050 M2T 0600 600 2.5 5 1 1.050 M2T 0800 800 3 7.5 1 1.050 M2T 1000 1000 5 10 1 1.050 80x120mm/3.15x4.72 hole. M3T 0500 500 4 1 1.250 M3T 0600 600 5 1 1.250 M3T 0800 800 3 7.5 1 1.250 M3T 1000 1000 5 10 1 1.250 M3T 1250 1250 7.5 15 1 1.250 M3T 1500 1500 8 17 1 1.250 80x160mm/3.15x6.30 hole. M4T 2000 2000 15 20 1 3.160 M4T 2500 2500 15 20 1 3.340 M4T 3000 3000 20 25 1 3.500 M4T 4000 4000 20 25 1 3.760 The M...T type current transformers (CTs) are installed in an electrical system to reduce the line current to a secondary value of 5 compatible with the ammeter inputs of the digital multimeters or protection relays. M...T are instrument transformers in class 0.5/1 without a primary winding and are normally used for high primary current values starting from 250. ational characteristics ating frequency: 50-60Hz Secondary output current: 5 verload withstand: 120% Ipn IEC rated insulation voltage Ui: 720V IEC rated short-time thermal current Ith: 40-60 Ipn for 1 second IEC rated dynamic current Idyn: 2.5 Ith for 1 second Insulation (dry type): Class E Screw terminals Sealable terminal covers Screw fixing (fixing elements standard supplied with the product) IEC degree of protection: IP30 mbient conditions: ating temature: -25...+50 C Storage temature: -40...+80 C. Relative humidity, non condensing: 90%. Certifications and compliance Certifications obtained: EC. Compliant with standards: IEC/E 61869-2, IEC/E 61869-1. M4T... imensions page -33-31
imensions [mm(in)] EERGY S Mechanical meter ME M100... igital meter ME 100... - ME 110... 17.5 (0.69") 59.9 (2.35") 43.8 (1.72") igital meter ME 115 T1 - ME 120 T1... ME 121 - ME 122 35.8 (1.41") 5 (0.20") 58 (2.28") 43.7 (1.72") igital meter ME 3... ata concentrator ME C - ME C PV1... 71.6 (2.82") 5 (0.20") 58 (2.28") 43.7 (1.72") igital meter ME 130 M 35.8 (1.41") 71.6 (2.82 ) 35.8 (1.41") 63 (2.48") 43.8 (1.72") 20 (0.79") 115 (4.53") 96 (3.78") 5 (0.20") 28.8 (1.13") 43.5 (1.71 ) 37.3 (1.47 ) 96 (3.78") (0.94") 19 (0.75") 92 (3.62") 110 (4.33") 101.3 (3.99") 64.5 (2.54 ) 96.3 (3.79 ) 90.8 (3.57") 96 (3.78") 92 (3.62") 98.3 (3.87") 104.7 (4.12") 45 (1.77") 90 (3.54") 5 (0.20") Ø4.2 (0.16") MUTIS MG 100 - MG 110 - MG 200 - MG 210 - MG 300 Expansion modules EXM... 71.6 (2.82") 5 (0.20") 63 (2.48") 43.8 (1.72") 42.7 (1.68") 11 (0.43") 35.8 (1.41") 63 (2.48") 43.8 (1.72") 54 (2.12") 91.6 (3.61") 91.7 (3.61") EXP 10... FUSH-MUT IG ISTRUMETS Instruments MK 0... - MK 1... 96 (3.78") (0.94") 81 (3.19") 9 (0.35") 92 (3.62") 44 (1.73") 48 (1.89") 105.4 (4.15") 90 (3.54") 45 (1.77") 63.5 (2.50") 93.4 (3.68") 95 (3.74") 90 (3.54") 45 (1.77") 63.5 (2.50") 36.4 (1 43") MG 600 - MG 610 - MG 611... 96 (3.78") 65 (2.56") 55 (2.16") 8.5 (0.33") MG 700 - MG 800... - MG 900... with expansion modules EXP... 96 (3.78") 26.3 (1.03") 53.2 (2.09") 19 (0.75") 92 (3.62") 61.5 (2.42") EXP 10... FUSH-MUT MUTIS MK 2... 96 (3.78") 14 (0.55") 62 (2.44") 6 (0.") 92 (3.62") 90 (3.54") 96 (3.78") 92 (3.62") 99.5 (3.92") 64.5 (2.54") 96 (3.78") 92 (3.62") 85 (3.35") 45 (1.77") 98.3 (3.87") 104.7 (4.12") 45 (1.77") 90 (3.54") 95 (3.74") 90 (3.54") 45 (1.77") 63.5 (2.50") Ø4.2 (0.16") Ø4.2 (0.16") Cutout EXP 10... Transducer MG 900T with expansion modules EXP... MG 900R remote display Cutout Cutout Cutout -32
imensions [mm(in)] IGIT IG ISTRUMETS MK 7... - MK 8... 53.5 (2.11") 5 (0.20") 58.1 (2.29") 43.8 (1.72") 90 (3.54") 99 (3.90") 105.4 (4.15") 45 (1.77") Ø4.2 (0.16") CURRET TRSFRMERS Solid core M0T... 32 (1.26 ) M2T... 52 (2.05") 9.5 (0.37") 46.5 (1.83") M3T... 71 (2.79") 9.5 (0.37") 62.5 (2.46") Ø22 (0.87 ) 44 (1.73 ) M35T... 66 (2.60 ) 30 (1.18 ) 28 (1.10") Ø23 (0.90") 10 (0.39") 20 25 (0.79") (0.79") 30 (1.18") 12.5 (0.49") 15 (0.59") 65.5 (2.58") 27.5 (1.08") 56.5 (2.22") 36.5 (1.44") M4T... Ø30 (1.18") 25 (0.98") 30 (1.18") 40 (1.57") 10 (0.39") 20 (0.79") 104 (4.09") 40 (1.57") 81.5 (3.19") 44.5 (1.75") 72.5 (2.85") 53 (2.08") Ø66 (2.60 ) 12.5 (0.49 ) 31.5 (1. ) 51.5 (2.03 ) 61.5 (2.42 ) 126.5 (4.98 ) Ø86 (3.38") 31 (1.22") 51 (2.01") 61 (2.40") 71 (2.79") 81 (3.19") 155 (6.10") 31.5 (1. ) 51.5 (2.03 ) 61.5 (2.42 ) 81.5 (3.21 ) 105 (4.13 ) M1TP0060... - M1TP0300 20 (0.79 ) 41.5 (1.63 ) M1TP0400... - M1TP0500 60 (2.36 ) 45 (1.77 ) 74 (2.91") 51 (2.01") 101 (3.98") 121 (4.76") 140 (5.51") 11.5 (0.45 ) 11 (0.43 ) 41.5 (1.63 ) Ø28 (1.10 ) 16 (0.63 ) 16.5 (0.65 ) 21.5 (0.85 ) 26 (1.02 ) 31.5 (1. ) 98.5 (3.88 ) Ø33 (1.30 ) 21 (0.83 ) 26.5 (1.04 ) 31.5 (1. ) 41.5 (1.63 ) 98.5 (3.88 ) 55 (2.16 ) 11.5 16.5 (0.45 ) (0.65 ) 21.5 26 (0.85 ) (1.02 ) 31.5 (1. ) 74.5 (2.93 ) M3TP... 11 21 (0.43 ) (0.83 ) 26.5 31.5 (1.04 ) (1. ) 41.5 (1.63 ) 74.5 (2.93 ) 65 (2.56 ) 45 (1.77 ) M5TP... 20 40 (1.57 ) (0.79 ) 6.4 (0.25 ) 15.5 (0.61 ) 65 (2.56 ) 45 (1.77 ) Ø52 (2.05 ) 21 (0.83 ) 52 (2.05 ) 61 (2.40 ) 127 (5.00 ) Ø85.5 (3.37 ) 22 (0.87 ) 45 (1.77 ) 81 (3.19 ) 101 (3.98 ) 163.5 (6.44 ) 21 (0.83 ) 25 (0.98 ) 61 (2.40 ) 101 (3.98 ) 16 (0.63 ) 20 (0.79 ) 45 (1.77 ) 54.5 (2.14 ) 6.4 (0.25 ) 15.5 (0.61 ) 55 (2.16 ) 22 (0.87 ) 45 (1.77 ) 62 (2.44 ) 81 (3.19 ) 101 (3.98 ) 144 (5.67 ) 16 (0.63 ) 20 (0.79 ) 45 (1.77 ) 80.5 (3.17 ) 6.4 (0.25 ) 15.5 (0.61 ) 55 (2.16 ) -33
imensions [mm(in)] Compact prewired split-core M1TM... 28 (1.10") M2TM... 33 (1.30") Split-core M1T... 114 (4.49") 50 (1.97") S2 P2 80 (3.15") 144 (5.67") 25 (0.98") 43.5 (1.71") 66.5 (2.62") 23 (0.90") 37 (1.46") 49.5 (1.95") 86 (3.38") 36.5 (1.44") (0.94") 45.5 (1.79") 34.5 (1.36") 37 (1.46") 57.5 (2.26") 42 (1.65") M2T... 142 (5.59") 50 (1.97") M3T... 142 (5.59") 50 (1.97") S2 P2 S2 P2 80 (3.15") 144 (5.67") 120 (4.72") 184 (7.") P2 32 (1.26") P2 32 (1.26") 52 (2.05") 78 (3.07") 32 (1.26") 80 (3.15") 109 (4.29") 32 (1.26") P2 32 (1.26") M4T... 80 (3.15") 109 (4.29") 32 (1.26") 184 (7.") 68 (2.68") S2 P2 38 (1.50") 38 (1.50") 47 (1.85") 32 (1.26") 5 (9.64") 160 (6.30") 175 (6.89") 80 (3.15") 120 (4.72") 32 (1.26") 52 (2.05") -34
Wiring diagrams EERGY S Mechanical ME M100 230VC ME M100 T1 5 6 230VC 640 pulses/kwh Vce max: 35V Imax: 20m igital ME 100 T1... - ME 110 T1... ME 115 T1 - ME 120 T1... ME 121... ME 122... ME 130 M IE 1+ 1- Static IE 1+ 1- Static IE B RS485 IE M1 M2 M-BUS + I1 I2 - UT 3 UT 4 1 1 2 2 14 11 12 21 22 ❶ 110-120VC ME...120; 220-0VC ME...; 230V 50Hz ME... T1 MI. 1 2 ME 300 T2... - ME 300 F IE 380-415V (-) 220-0V (-) 1 2 3 1 2 3 Tariff input 100...0VC T1 T2 + 1 Static 2 + Pulse output 30VC 50m ❶ 230V 50Hz (-), 400V 50Hz (-) ME... T2 MI / ME... F. ME 310 T2... - ME 310 F... 1 380-415V (-) 2 220-0V (-) 3 V1 V2 V3 V S1S2 S1 S2 S1 T1 T2 1+ Static I1 I2 I3 S2 1-2+ 2- Pulse output 30VC 50m ME 301 IE 380-415V (-) 220-0V (-) 1 2 3 1 2 3 Tariff input 100...0VC T1 TR T2 RS485 B S ME 302 IE 380-415V (-) 220-0V (-) 1 2 3 1 2 3 Tariff input 100...0VC T1 T2 M1 M2 M1 M2 M-BUS ME 330 - ME 305 T2 Single-phase Two-phase Three-phase with or without neutral CT2 CT2 CT3 V1 V2 V3 V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET Three-phase without neutral in R connection Tariff input Pulse output 30VC 50m for ME 305 T2 CT2 CT3 100...0VC T1 T2 Static 1+ 1-2+ 2- RS485 for ME 330 TR B S V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET RS485 M-Bus for ME 332 M1 M2 M1 M2 M-BUS ata concentrator ME C 100...0VC 110...250VC 100...0VC 110VC CM1 I1.1 I1.2 1 2 T1 T2 TR B SG ux Supply Tariff Input RS485 2 x 4 groups Insulated inputs CM2 I2.1 I2.2 CM3 I3.1 I3.2 CM4 I4.1 I4.2-35
Wiring diagrams MUTIS MG 100 - MG 110 - MG 200 - MG 210 - MG 300 Single-phase Two-phase Three-phase with or without neutral CT2 CT2 CT3 110...250VC 100...0VC 110...250VC 100...0VC 110...250VC 100...0VC 1 2 UX SUPPY V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET 1 2 UX SUPPY V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET 1 2 UX SUPPY V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET Three-phase without neutral in R connection Balanced 3-phase connection with or without neutral CT2 CT3 1 2 3 S1 S2 110...250VC 100...0VC 110...250VC 100...0VC 100...0VC 110...250VC 1 2 UX SUPPY V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET 1 2 UX SUPPY V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET --- + 1 2 UX SUPPY V1 V2 V3 V VTGE S1 S2 I1 S1 S2 S1 S2 I2 I3 CURRET B RS485 MUTIS MG 600-610... - MG 700 - MG 800... Single-phase Two-phase MG 900... Single-phase Two-phase 12--48VC ❶ 110...250VC 100...440VC 12--48VC ❶ 110...250VC 100...440VC CT2 12--48VC ❷ 110...250VC 100...440VC 12--48VC ❷ 110...250VC 100...440VC CT2 1 2 UX SUPPY V1 V2 V3 V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET 1 2 UX SUPPY V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET 1 2 UX SUPPY V1 V2 V3 V4V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET S1 S2 I4 1 2 V1 V2 V3 V4V S1 S2 S1 S2 S1 S2 I1 I2 I3 UX SUPPY VTGE CURRET S1 S2 I4 Three-phase with or without neutral Three-phase with or without neutral CT2 CT3 CT2 CT3 12--48VC ❶ 110...250VC 100...440VC 12--48VC ❷ 110...250VC 100...440VC 1 2 UX SUPPY V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET 1 2 V1 V2 V3 V4V S1 S2 S1 S2 S1 S2 I1 I2 I3 UX SUPPY VTGE CURRET S1 S2 I4 Three-phase without neutral in R connection Three-phase without neutral in R connection 12--48VC ❶ 110...250VC 100...440VC CT2 12--48VC ❷ 110...250VC 100...440VC CT2 12--48VC ❷ 110...250VC 100...440VC CT3 1 2 UX SUPPY V1 V2 V3V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET 1 2 V1 V2 V3 V4V S1 S2 S1 S2 S1 S2 I1 I2 I3 UX SUPPY VTGE CURRET S1 S2 I4 1 2 UX SUPPY V1 V2 V3 V4V VTGE S1 S2 S1 S2 S1 S2 I1 I2 I3 CURRET S1 S2 I4 12--48VC ❶ 110...250VC 100...440VC 1 2 UX SUPPY ❶ For MG 800... 048 only. CT3 V1 V2 V3V S1 S2 S1 S2 S1 S2 I1 I2 I3 VTGE CURRET Two-phase with neutral. Measurement of neutral current and neutral-earth voltage 12--48VC ❷ 110...250VC 100...440VC CT2 1 2 V1 V2 V3 V4V S1 S2 S1 S2 S1 S2 I1 I2 I3 UX SUPPY VTGE CURRET CT4 S1 S2 I4 Three-phase with neutral. Measurement of neutral current and neutral-earth voltage 12--48VC ❷ 110...250VC 100...440VC CT2 CT3 1 2 V1 V2 V3 V4V S1 S2 S1 S2 S1 S2 I1 I2 I3 UX SUPPY VTGE CURRET CT4 S1 S2 I4 ❷ For MG 900... 048 only. -36
Wiring diagrams IG ISTRUMETS MK 00 - MK 00 R1 MK 01 - MK 01 R1 MK 02 Voltmeter / 1.3 1.4 / 1.5 1.6 / 1.3 1.4 1.5 1.6 mmeter / 1.3 1.4 1.5 1.6 600V~ 5~ 600V~ 5~ 1.1 1.2 3.2 3.1 3.3 220...0VC For MK 00 R1 1.1 1.2 3.2 3.1 3.3 220...0VC For MK 01 R1 1.1 1.2 220...0VC 1.1 1.2 220...0VC MK 03 - MK 03 R1 MK 04 - MK 04 R1 Single-phase Three-phase / 1.3 1.4 1 2 3 1.3 1.4 1.5 1.6 600V~ 45/65Hz 600V~ 5~ 1.1 1.2 3.2 3.1 3.3 220...0VC For MK 03 R1 1.1 1.2 3.2 3.1 3.3 220...0VC For MK 04 R1 MK 10 - MK 10 R1 MK 11 - MK 11 R1 MK 15 - MK 15 R1 MK 16 - MK 16 R1 1 2 3 1 2 3 1 2 3 1 2 3 1.3 1.4 1.5 1.6 1.3 1.4 1.5 1.6 1.3 1.4 1.5 1.6 2.1 2.2 2.3 2.4 1.3 1.4 1.5 1.6 2.1 2.2 2.3 2.4 600V~ 5~ 600V~ 5~ 600V~ 5~ 1.1 1.2 220...0VC 3.2 3.1 3.3 For MK 10 R1 1.1 1.2 220...0VC 3.2 3.1 3.3 For MK 11 R1 1.1 1.2 220...0VC 3.2 3.1 3.3 For MK 15 R1 1.1 1.2 220...0VC 3.2 3.1 3.3 For MK 16 R1 MK 80 - MK 80 R1 MK 81 - MK 81 R1 MK 82 Voltmeter / 600V~ / / S1 5~ S2 / 600V~ / S1 S2 mmeter / / S1 S2 5~ MK 70 - MK 70 R1 1 2 3 1 2 3 600V~ / 1 2 14 12 11 220...0VC 600V~ 45/65Hz For MK 80 R1 MK 83 - MK 83 R1 / 1 2 14 12 11 220...0VC For MK 81 R1 1 2 3 1 2 220...0VC MK 84 - MK 84 R1 Single-phase / 600V~ 5~ S1 S2 1 2 3 1 2 220...0VC Three-phase 1.3 1.4 1.5 1.6 600V~ 5~ 1 2 3 1 2 220...0VC I1 I2 I3 CM 5~ 14 12 11 For MK 70 R1 MK 71 - MK 71 R1 1 2 14 12 11 220...0VC For MK 83 R1 FUSH-MUT MUTIS MK2... Single-phase MK 2... 208...0VC MK 25 12...VC Two-phase 1 2 MK 2... 208...0VC MK 25 12...VC CT2 1 2 14 12 11 1.1 1.2 3.2 3.1 3.3 220...0VC 220...0VC For MK 84 R1 For MK 84 R1 Three-phase with or without neutral 1 CT2 2 CT3 3 MK 2... 208...0VC MK 25 12...VC 1 2 3 1 2 220...0VC 1 2 3 600V~ 14 12 11 For MK 71 R1 MK 75 - MK 75 R1 I1 I2 I3 CM 5~ 1 2 3 I1 I2 I3 C 1 2 3 I1 I2 I3 C 1 2 3 I1 I2 I3 C UX SUPPY VTGE CURRET UX SUPPY VTGE CURRET UX SUPPY VTGE CURRET 1 2 220...0VC 14 13 For MK 75 R1 Three-phase without neutral in R connection 1 2 3 CT2 1 2 3 CT3 MK 2... 208...0VC MK 25 12...VC MK 2... 208...0VC MK 25 12...VC 1 2 3 I1 I2 I3 C 1 2 3 I1 I2 I3 C UX SUPPY VTGE CURRET UX SUPPY VTGE CURRET -37