EX310 (MS-1333)Disassemble SOP 1 Battery Pack 2 BOTTOM DOOR ASSY 3 WLAN THERMAL-KIT And CPU Module 4 MDC And RAM Module 5 HDD Module ASSY 6 ODD Module ASSY 7 HINGE COVER ASSY 8 UP CASE ASSY 9 LOWER CASE ASSY 10 LCD MODULE ASSY
1 Battery Pack 1-1:Push the battery Unlock button as below; 1-2:Push the battery Release button as below, then slide the battery pack out of the slot; 1 Battery Pack S9N-0086200-W38 1
2 BOTTOM DOOR ASSY 2-1:Remove 4pcs M2.5*5mm screws with Screw Driver. Note:Screw driver torque is 1.8~2.2kgf.cm 4 3 1 2 2-2:Remove Bottom Door Assy as below; 1 Screw E43-I250551-H29 4 2 BOTTOM DOOR ASSY 307-221J212-W28 1
3 WLAN,THERMAL-KIT And CPU Module 3-1:Remove 3pcs M2*6 screws and CPU Fan sink Cable. Note:Screw driver torque is 2.0~2.5kgf.cm 3 2 1 Cable 3-2: Remove CPU FAN. 1 screw E43-1206001-H29 3
3-3: Remove 1pcs M2*3mm screw, and then Remove 2pcs PIFA ANTENNA/R L as below; Note:Screw driver torque is 1.5~2.0kgf.cm 1 3-4:Remove wlan as below; 1 wlan 605-6890-010 1 2 Screw E43-1203003-H29 1
3-5 Remove 4pcs M2.5*5 screws and 1pcs spring screw as below. Note:Screw driver torque is 2.0~2.5kgf.cm 3 2 1 5 4 1 screw E43-I250551-H29 4
3-6:Remove CPU Thermal Module as below; 1 CPU FAN E33-0900221-F05 1 2 CPU Thermal Module E31-1700034-F05 1
EX310(MS-1333) Disassemble SOP 3-7:Open the CPU Slot; 3-8:Remove CPU Module as below; 1 CPU Module A10-K82G136-A08 1
4 MDC And RAM Module 4-1:Remove 2pcs M2*3mm screws as below; Note:Screw driver torque is 1.5~1.8kgf.cm 1 2 4-2:Remove MDC Cable,Then Remove MODEM as below; 1 MODEM S52-2801180-C59 1 2 Screw E43-1203003-H29 2
4-3:Push the RAM locks away; 4-4:Take off the RAM Module as below: 1 RAM Module S7C-S346801-T10 2
5 HDD Module ASSY 5-1:Remove 2pcs M2.5*5mm screws Then Remove HDD Module Assy as below; Note:Screw driver torque is 1.8~2.2kgf.cm 2 1 1 Screw E43-I250551-H29 2
5-2:Remove 2pcs M3*3.5mm screws, Then Remove HDD Bracket as below; Note:Screw driver torque is 1.5~1.8kgf.cm 1 2 1 Screw E43-1303501-H29 2 2 HDD Bracket Assy E2M-2211511-Y28 1 3 HDD MODULE ASSY S71-2425501-W36 1
6 ODD Module ASSY 6-1:Remove ODD Module Assy as below;
6-2:Remove ODD Bezel as below ; 1 ODD Bezel 307-221F212-Y31 1
6-3:Remove 2pcs M2*3mm screws as below; Note:Screw driver torque is 1.5~1.8kgf.cm 1 2 1 Screw E43-1203003-H29 2 2 ODD Side Bracket E2M-2211611-Y28 1 3 ODD MODULE ASSY S7D-2270001-SI4 1
7 HINGE COVER ASSY EX310(MS-1333)Disassemble SOP 7-1:Attention: Push Fastener as below; 1 2 3 7-2:Unlock the hooks of both sides; 7-3:Remove LCD LVDS Cable CAMERA CABLE and Inverter Cable as below;
7-4:Remove MICROPHONE CABLE Speaker CABLE as below; 1 INVERTER Cable K1H-3006007-H39 1 2 Camera Cable K10-3004099-H58 1 3 LCD LVDS Cable K19-3020016-H58 1 4 BLUETOOTH CABLE K10-3008063-H58 1
7-5:Pull out cable from the slot as below;
7-6:Remove 2pcs M2.5*5mm screws as below; Note:Screw driver torque is 1.8~2.2kgf.cm 1 2 1 Screw E43-I250551-H29 2
7-7:Remove LCD MODULE ASSY as below;; EX310(MS-1333)Disassemble SOP
8 UPCASE ASSY 8-1:Remove 4pcs Middle Shielding Cover; 1 2 3 4 1 Middle Shielding Cover E2M-2240211-Y31 4
8-2:Remove Keyboard as below; 8-3:Remove Keyboard Cable as below; 1 Keyboard S1N-1UUS231-C54 1
; 8-4: Remove Launch Board Cable as below 8-5: Remove Touchpad FFC (To M/B).
8-6:Remove SIM Card Door as below; 1 SIM CARD DOOR E2P-2210211-Y31 1
8-7:Remove 9pcs M2.5*5mm Screws as below, Note:Screw driver torque is 1.8~2.2kgf.cm 4 9 8 3 7 2 1 5 6 1 Screw E43-I250551-H29 9
8-8:Remove 3pcs M2*3mm Screws and 1pcs M2.5*5 screw as below; Note:Screw driver torque is 1.2~1.5kgf.cm(1-3) Note:Screw driver torque is 1.8~2.2kgf.cm (1) 1 2 3 1 1 Screw E43-1203003-H29 3 2 Screw E43-I250551-H29 1
8-9:Remove PCI-EXPRESS DUMMY CARD Then Remove SD DUMMY CARD as below; 1 PCI-EXPRESS DUMMY CARD E2P-2212814-H76 1 2 SD DUMMY CARD E2P-2212712-H76 1
8-10:Remove 2pcs M2*3mm Screws, Then Remove Launch Board as below; Note:Screw driver torque is 1.5~1.8kgf.cm 1 2
8-11:Remove Launch Board Cable as below; 1 Screw E43-1203003-H29 2 2 Launch Board 607-1226A-B10 1 3 Launch Board Cable K1C-1020002-J36 1
8-12:Remove 2pcs M2*3mm Screws, Then Remove VSO-ANTENNA COVER as below; Note:Screw driver torque is 1.2~1.5kgf.cm 1 2 8-13: Remove VSO-ANTENNA. 1 Screw E43-1203003-H29 2 2 COVER E2P-2214321-Y31 1 3 VSO-ANTENNA S79-1800B90-V30 1
8-14:Remove 4pcs M2*3mm Screws, Then Remove SPEAKER_SHIELDING as below; Note:Screw driver torque is 1.5~1.8kgf.cm 1 2 3 4 1 Screw E43-1203003-H29 4 2 SPEAKER_SHIELDING E2M-2240111-Y28 2
8-15:Remove Speaker as below; 1 Speaker S33-A000600-SH2 1
8-16:Remove 2pcs M2*3.5mm Screws as below; Note:Screw driver torque is 1.5~1.8kgf.cm 2 1 1 Screw E43-1203501-H29 2
8-17:Remove Touchpad FFC (To Button) Finger Printer board Cable, Then Remover Touchpad Button Board as below; 8-18:Remove Finger Printer Board as below;
8-19:Remove FFC Cable (TO Button),Then Remove Touchpad Module as below; 8-20:Remove 2pcs MAGNET as below; 1 Touchpad Module S78-3700400-SD2 1 2 Touchpad FFC (To Button) K1C-1012012-J36 1 3 MAGNET E2Y-3310212-SF7 2 4 Upper Case Assy 307-334C221-H74 1
8-21:Remove Touchpad FFC (To M/B) as below; 8-22:Remove Finger Printer board Cable as below; 1 Touchpad Button Board 607-12262-B10 1 2 Touchpad FFC (To M/B) K1C-1012016-J36 1 3 Finger Printer Board 607-13312-010 1 4 Finger Printer board Cable K1C-1006016-J36 1
8-23::Remove Bluetooth Antenna,Then Remove BLUETOOTH CABLE as below; 8-24:Remove BLUETOOTH MODULE as below; 1 BLUETOOTH ANTENNA S79-1800610-V03 1 2 BLUETOOTH MODULE 605-6837D-070 1 3 BLUETOOTH CABLE K10-3008063-H58 1
9 LOWER CASE ASSY 9-1:Remove1pcs M2.5*5mm Screw, then remove M/B as below; Note:Screw driver torque is 1.8~2.2kgf.cm 1 1 Screw E43-I250551-H29 1 2 M/B 607-13331-020 1
9-2:Remove WLAN Antenna-L R BLUETOOTH ANTENNA, Then Remove RJ11 CABLE as below; BLUETOOTH ANTENNA RJ11 CABLE WLAN Antenna-L WLAN Antenna-R 1 WLAN Antenna-L S79-1800900-V03 1 2 WLAN Antenna-R S79-1800910-V03 1 3 RJ11 CABLE K10-3002094-H58 1
9-3:Remove TV IO JACK as below; 1 TV IO JACK K19-3001009-H39 1 2 Lower Case Assy 307-221D216-Y31 1
10 LCD MODULE ASSY EX310(MS-1333)Disassemble SOP 10-1:Remove 4pcs LCD Rubber,Then Remove 2pcs LCD BEZEL RUBBER as below; LCD Rubber LCD BEZEL RUBBER LCD BEZEL RUBBER LCD Rubber LCD Rubber LCD Rubber 10-2:Remove 4pcs M2.5*5mm screws as below; Note:Screw driver torque is 2.0-2.2kgf.cm 1 2 3 4 1 LCD Rubber E2Y-3110611-Y40 4 2 Screw E43-I250551-H29 4 3 LCD BEZEL RUBBER E2Y-2210711-Y40 2
10-3:Remove LCD Bezel as below; ; 1 LCD BEZEL 307-331B212-Y31 1
10-4:Remove 2pcs M2.5*5mm screws, then remove Hinge_L-R as below; Note:Screw driver torque is 2.0-2.5kgf.cm 1 2 1 Hinge_Left E2M-3310311-G60 1 2 Hinge_Right E2M-3310411-G60 1 3 screw E43-I250551-H29 2
10-5:Remove Inverter Cable as blew; 10-6:Remove Inverter Module, Then Remove Display Module as below; 1 Notebook Inverter S78-3300450-SG3 1 2 Display Module S78-2307210-A90 1
10-7:Remove Camera Cable as below; 10-8:Remove CMOS Camera Module as below; 1 CMOS Camera Module S1F-0003020-C54 1 2 Camera Cable K10-3004099-H58 1
10-9:Remove MICROPHONE as below;; 1 MICROPHONE S34-2100720-N44 1
10-10:Remove 2pcs MAGNET as below; 2 1 1 LCD COVER E43-I250551-H29 1 2 MAGNET E2Y-3310113-SF7 2
10-11:Remove Coaxial Cable as below; 1 LCD LVDS Cable K19-3020016-H58 1
10-12:Remove 6pcs M2*3mm Screws, Then Remove LCD Bracket as below; Note:Screw driver torque is 1.6-1.8kgf.cm 1 3 5 6 2 4 1 Screw E43-1203003-H29 6 2 LCD-Bracket-R E2M-3310211-Y28 1 3 LCD-Bracket-L E2M-3310111-Y28 1
EX310(MS-1333)screws specification Photo Screw specification label (M2.5*L5MM) black (M2*L3MM)white (M3*L3.5MM) white (M2*L3.5MM) black (M2*6MM)white
EX310(MS-1333)screws specification 1 Bottom Door total 7pcs screws, specification: Photo Screw specification Label (M2.5*L5MM) black
EX310(MS-1333)screws specification 2 THERMAL-KIT and HDD total 10pcs Screws specification: 1 3 2 2 1 3 2 1 5 4 Photo Screw specification label (M2.5*L5MM) black (M2*L6MM)white
EX310 (MS-1333)screws specification 3 WIRELESS,MDC CARD and HDD ASSY total 5pcs screws, specification: Photo Screw specification label (M3*L3.5MM) white (M2*L3MM)white
EX310(MS-1333)screws specification 4 LCD Bezel total 4pcs screws, specification: Photo Screw specification Label (M2.5*L5MM) black
EX310(MS-1333)screws specification 5. LCD Bracket total 8pcs screws, specification: Photo Screw specification Label (M2.5*L5MM) black (M2*L3MM)white
EX310(MS-1333)screws specification 6 Upper Case Assy screw total 1pcs, specification: Photo Screw specification Label (M2.5*L5MM) black
EX310 (MS-1333)screws specification 7. UPCASE and LOWER CASES total 12pcs screws, specification: Photo Screw specification label (M2.5*L5MM)black (M2*L3MM)white
EX310(MS-1333)screws specification 8 Touch Pad Board total 10pcs screws, specification: Photo Screw specification label (M2*L3.5MM) black (M2*L3MM)white
EX310(MS-1333)screws specification 9 NB screw 1pcs, specification: Photo Screw specification label (M2.5*L5MM) black